/* * Copyright (C) 2018 Marvell International Ltd. * * SPDX-License-Identifier: BSD-3-Clause * https://spdx.org/licenses */ #include #include #include #include #include #include #include #include #include #include #include /* Register for skip image use */ #define SCRATCH_PAD_REG2 0xF06F00A8 #define SCRATCH_PAD_SKIP_VAL 0x01 #define NUM_OF_GPIO_PER_REG 32 #define MMAP_SAVE_AND_CONFIG 0 #define MMAP_RESTORE_SAVED 1 /* SAR clock settings */ #define MVEBU_AP_GEN_MGMT_BASE (MVEBU_RFU_BASE + 0x8000) #define MVEBU_AP_SAR_REG_BASE(r) (MVEBU_AP_GEN_MGMT_BASE + 0x200 +\ ((r) << 2)) #define SAR_CLOCK_FREQ_MODE_OFFSET (0) #define SAR_CLOCK_FREQ_MODE_MASK (0x1f << SAR_CLOCK_FREQ_MODE_OFFSET) #define SAR_PIDI_LOW_SPEED_OFFSET (20) #define SAR_PIDI_LOW_SPEED_MASK (1 << SAR_PIDI_LOW_SPEED_OFFSET) #define SAR_PIDI_LOW_SPEED_SHIFT (15) #define SAR_PIDI_LOW_SPEED_SET (1 << SAR_PIDI_LOW_SPEED_SHIFT) #define FREQ_MODE_AP_SAR_REG_NUM (0) #define SAR_CLOCK_FREQ_MODE(v) (((v) & SAR_CLOCK_FREQ_MODE_MASK) >> \ SAR_CLOCK_FREQ_MODE_OFFSET) #define AVS_I2C_EEPROM_ADDR 0x57 /* EEPROM */ #define AVS_EN_CTRL_REG (MVEBU_AP_GEN_MGMT_BASE + 0x130) #define AVS_ENABLE_OFFSET (0) #define AVS_SOFT_RESET_OFFSET (2) #define AVS_TARGET_DELTA_OFFSET (21) #ifndef MVEBU_SOC_AP807 /* AP806 SVC bits */ #define AVS_LOW_VDD_LIMIT_OFFSET (4) #define AVS_HIGH_VDD_LIMIT_OFFSET (12) #define AVS_VDD_LOW_LIMIT_MASK (0xFF << AVS_LOW_VDD_LIMIT_OFFSET) #define AVS_VDD_HIGH_LIMIT_MASK (0xFF << AVS_HIGH_VDD_LIMIT_OFFSET) #else /* AP807 SVC bits */ #define AVS_LOW_VDD_LIMIT_OFFSET (3) #define AVS_HIGH_VDD_LIMIT_OFFSET (13) #define AVS_VDD_LOW_LIMIT_MASK (0x3FF << AVS_LOW_VDD_LIMIT_OFFSET) #define AVS_VDD_HIGH_LIMIT_MASK (0x3FF << AVS_HIGH_VDD_LIMIT_OFFSET) #endif /* VDD limit is 0.9V for A70x0 @ CPU frequency < 1600MHz */ #define AVS_A7K_LOW_CLK_VALUE ((0x80 << AVS_TARGET_DELTA_OFFSET) | \ (0x1A << AVS_HIGH_VDD_LIMIT_OFFSET) | \ (0x1A << AVS_LOW_VDD_LIMIT_OFFSET) | \ (0x1 << AVS_SOFT_RESET_OFFSET) | \ (0x1 << AVS_ENABLE_OFFSET)) /* VDD limit is 1.0V for all A80x0 devices */ #define AVS_A8K_CLK_VALUE ((0x80 << AVS_TARGET_DELTA_OFFSET) | \ (0x24 << AVS_HIGH_VDD_LIMIT_OFFSET) | \ (0x24 << AVS_LOW_VDD_LIMIT_OFFSET) | \ (0x1 << AVS_SOFT_RESET_OFFSET) | \ (0x1 << AVS_ENABLE_OFFSET)) /* VDD limit is 0.82V for all A3900 devices * AVS offsets are not the same as in A70x0 */ #define AVS_A3900_CLK_VALUE ((0x80u << 24) | \ (0x2c2 << 13) | \ (0x2c2 << 3) | \ (0x1 << AVS_SOFT_RESET_OFFSET) | \ (0x1 << AVS_ENABLE_OFFSET)) /* VDD is 0.88V for 2GHz clock */ #define AVS_A3900_HIGH_CLK_VALUE ((0x80u << 24) | \ (0x2f5 << 13) | \ (0x2f5 << 3) | \ (0x1 << AVS_SOFT_RESET_OFFSET) | \ (0x1 << AVS_ENABLE_OFFSET)) #define MVEBU_AP_EFUSE_SRV_CTRL_REG (MVEBU_AP_GEN_MGMT_BASE + 0x8) #define EFUSE_SRV_CTRL_LD_SELECT_OFFS 6 #define EFUSE_SRV_CTRL_LD_SEL_USER_MASK (1 << EFUSE_SRV_CTRL_LD_SELECT_OFFS) /* * - Identification information in the LD-0 eFuse: * DRO: LD0[74:65] - Not used by the SW * Revision: LD0[78:75] - Not used by the SW * Bin: LD0[80:79] - Not used by the SW * SW Revision: LD0[115:113] * Cluster 1 PWR: LD0[193] - if set to 1, power down CPU Cluster-1 * resulting in 2 CPUs active only (7020) */ #define MVEBU_AP_LD_EFUSE_BASE (MVEBU_AP_GEN_MGMT_BASE + 0xF00) /* Bits [94:63] - 32 data bits total */ #define MVEBU_AP_LD0_94_63_EFUSE_OFFS (MVEBU_AP_LD_EFUSE_BASE + 0x8) /* Bits [125:95] - 31 data bits total, 32nd bit is parity for bits [125:63] */ #define MVEBU_AP_LD0_125_95_EFUSE_OFFS (MVEBU_AP_LD_EFUSE_BASE + 0xC) /* Bits [220:189] - 32 data bits total */ #define MVEBU_AP_LD0_220_189_EFUSE_OFFS (MVEBU_AP_LD_EFUSE_BASE + 0x18) /* Offsets for the above 2 fields combined into single 64-bit value [125:63] */ #define EFUSE_AP_LD0_DRO_OFFS 2 /* LD0[74:65] */ #define EFUSE_AP_LD0_DRO_MASK 0x3FF #define EFUSE_AP_LD0_REVID_OFFS 12 /* LD0[78:75] */ #define EFUSE_AP_LD0_REVID_MASK 0xF #define EFUSE_AP_LD0_BIN_OFFS 16 /* LD0[80:79] */ #define EFUSE_AP_LD0_BIN_MASK 0x3 #define EFUSE_AP_LD0_SWREV_OFFS 50 /* LD0[115:113] */ #define EFUSE_AP_LD0_SWREV_MASK 0x7 #ifndef MVEBU_SOC_AP807 /* AP806 AVS work points in the LD0 eFuse * SVC1 work point: LD0[88:81] * SVC2 work point: LD0[96:89] * SVC3 work point: LD0[104:97] * SVC4 work point: LD0[112:105] */ #define EFUSE_AP_LD0_SVC1_OFFS 18 /* LD0[88:81] */ #define EFUSE_AP_LD0_SVC2_OFFS 26 /* LD0[96:89] */ #define EFUSE_AP_LD0_SVC3_OFFS 34 /* LD0[104:97] */ #define EFUSE_AP_LD0_WP_MASK 0xFF #else /* AP807 AVS work points in the LD0 eFuse * SVC1 work point: LD0[91:81] * SVC2 work point: LD0[102:92] * SVC3 work point: LD0[113:103] */ #define EFUSE_AP_LD0_SVC1_OFFS 17 /* LD0[91:81] */ #define EFUSE_AP_LD0_SVC2_OFFS 28 /* LD0[102:92] */ #define EFUSE_AP_LD0_SVC3_OFFS 39 /* LD0[113:103] */ #define EFUSE_AP_LD0_WP_MASK 0x3FF #endif #define EFUSE_AP_LD0_SVC4_OFFS 42 /* LD0[112:105] */ #define EFUSE_AP_LD0_CLUSTER_DOWN_OFFS 4 #if MARVELL_SVC_TEST #define MVEBU_CP_MPP_CTRL37_OFFS 20 #define MVEBU_CP_MPP_CTRL38_OFFS 24 #define MVEBU_CP_MPP_I2C_FUNC 2 #define MVEBU_MPP_CTRL_MASK 0xf #endif /* Return the AP revision of the chip */ static unsigned int ble_get_ap_type(void) { unsigned int chip_rev_id; chip_rev_id = mmio_read_32(MVEBU_CSS_GWD_CTRL_IIDR2_REG); chip_rev_id = ((chip_rev_id & GWD_IIDR2_CHIP_ID_MASK) >> GWD_IIDR2_CHIP_ID_OFFSET); return chip_rev_id; } /****************************************************************************** * The routine allows to save the CCU and IO windows configuration during DRAM * setup and restore them afterwards before exiting the BLE stage. * Such window configuration is required since not all default settings coming * from the HW and the BootROM allow access to peripherals connected to * all available CPn components. * For instance, when the boot device is located on CP0, the IO window to CP1 * is not opened automatically by the HW and if the DRAM SPD is located on CP1 * i2c channel, it cannot be read at BLE stage. * Therefore the DRAM init procedure have to provide access to all available * CPn peripherals during the BLE stage by setting the CCU IO window to all * CPnph addresses and by enabling the IO windows accordingly. * Additionally this function configures the CCU GCR to DRAM, which allows * usage or more than 4GB DRAM as it configured by the default CCU DRAM window. * * IN: * MMAP_SAVE_AND_CONFIG - save the existing configuration and update it * MMAP_RESTORE_SAVED - restore saved configuration * OUT: * NONE **************************************************************************** */ static void ble_plat_mmap_config(int restore) { if (restore == MMAP_RESTORE_SAVED) { /* Restore all orig. settings that were modified by BLE stage */ ccu_restore_win_all(MVEBU_AP0); /* Restore CCU */ iow_restore_win_all(MVEBU_AP0); return; } /* Store original values */ ccu_save_win_all(MVEBU_AP0); /* Save CCU */ iow_save_win_all(MVEBU_AP0); init_ccu(MVEBU_AP0); /* The configuration saved, now all the changes can be done */ init_io_win(MVEBU_AP0); } /**************************************************************************** * Setup Adaptive Voltage Switching - this is required for some platforms **************************************************************************** */ #if !MARVELL_SVC_TEST static void ble_plat_avs_config(void) { uint32_t freq_mode, device_id; uint32_t avs_val = 0; freq_mode = SAR_CLOCK_FREQ_MODE(mmio_read_32(MVEBU_AP_SAR_REG_BASE( FREQ_MODE_AP_SAR_REG_NUM))); /* Check which SoC is running and act accordingly */ if (ble_get_ap_type() == CHIP_ID_AP807) { /* Increase CPU voltage for higher CPU clock */ if (freq_mode == CPU_2000_DDR_1200_RCLK_1200) avs_val = AVS_A3900_HIGH_CLK_VALUE; else avs_val = AVS_A3900_CLK_VALUE; } else { /* Check which SoC is running and act accordingly */ device_id = cp110_device_id_get(MVEBU_CP_REGS_BASE(0)); switch (device_id) { case MVEBU_80X0_DEV_ID: case MVEBU_80X0_CP115_DEV_ID: /* Always fix the default AVS value on A80x0 */ avs_val = AVS_A8K_CLK_VALUE; break; case MVEBU_70X0_DEV_ID: case MVEBU_70X0_CP115_DEV_ID: /* Fix AVS for CPU clocks lower than 1600MHz on A70x0 */ if ((freq_mode > CPU_1600_DDR_900_RCLK_900_2) && (freq_mode < CPU_DDR_RCLK_INVALID)) avs_val = AVS_A7K_LOW_CLK_VALUE; break; default: ERROR("Unsupported Device ID 0x%x\n", device_id); return; } } if (avs_val) { VERBOSE("AVS: Setting AVS CTRL to 0x%x\n", avs_val); mmio_write_32(AVS_EN_CTRL_REG, avs_val); } } #endif /****************************************************************************** * Update or override current AVS work point value using data stored in EEPROM * This is only required by QA/validation flows and activated by * MARVELL_SVC_TEST flag. * * The function is expected to be called twice. * * First time with AVS value of 0 for testing if the EEPROM requests completely * override the AVS value and bypass the eFuse test * * Second time - with non-zero AVS value obtained from eFuses as an input. * In this case the EEPROM may contain AVS correction value (either positive * or negative) that is added to the input AVS value and returned back for * further processing. ****************************************************************************** */ static uint32_t avs_update_from_eeprom(uint32_t avs_workpoint) { uint32_t new_wp = avs_workpoint; #if MARVELL_SVC_TEST /* --------------------------------------------------------------------- * EEPROM | Data description (avs_step) * address | * --------------------------------------------------------------------- * 0x120 | AVS workpoint correction value * | if not 0 and not 0xff, correct the AVS taken from eFuse * | by the number of steps indicated by bit[6:0] * | bit[7] defines correction direction. * | If bit[7]=1, add the value from bit[6:0] to AVS workpoint, * | othervise substruct this value from AVS workpoint. * --------------------------------------------------------------------- * 0x121 | AVS workpoint override value * | Override the AVS workpoint with the value stored in this * | byte. When running on AP806, the AVS workpoint is 7 bits * | wide and override value is valid when bit[6:0] holds * | value greater than zero and smaller than 0x33. * | When running on AP807, the AVS workpoint is 10 bits wide. * | Additional 2 MSB bits are supplied by EEPROM byte 0x122. * | AVS override value is valid when byte @ 0x121 and bit[1:0] * | of byte @ 0x122 combined have non-zero value. * --------------------------------------------------------------------- * 0x122 | Extended AVS workpoint override value * | Valid only for AP807 platforms and must be less than 0x4 * --------------------------------------------------------------------- */ static uint8_t avs_step[3] = {0}; uintptr_t reg; uint32_t val; unsigned int ap_type = ble_get_ap_type(); /* Always happens on second call to this function */ if (avs_workpoint != 0) { /* Get correction steps from the EEPROM */ if ((avs_step[0] != 0) && (avs_step[0] != 0xff)) { NOTICE("AVS request to step %s by 0x%x from old 0x%x\n", avs_step[0] & 0x80 ? "DOWN" : "UP", avs_step[0] & 0x7f, new_wp); if (avs_step[0] & 0x80) new_wp -= avs_step[0] & 0x7f; else new_wp += avs_step[0] & 0x7f; } return new_wp; } /* AVS values are located in EEPROM * at CP0 i2c bus #0, device 0x57 offset 0x120 * The SDA and SCK pins of CP0 i2c-0: MPP[38:37], i2c function 0x2. */ reg = MVEBU_CP_MPP_REGS(0, 4); val = mmio_read_32(reg); val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) | (MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS)); val |= (MVEBU_CP_MPP_I2C_FUNC << MVEBU_CP_MPP_CTRL37_OFFS) | (MVEBU_CP_MPP_I2C_FUNC << MVEBU_CP_MPP_CTRL38_OFFS); mmio_write_32(reg, val); /* Init CP0 i2c-0 */ i2c_init((void *)(MVEBU_CP0_I2C_BASE)); /* Read EEPROM only once at the fist call! */ i2c_read(AVS_I2C_EEPROM_ADDR, 0x120, 2, avs_step, 3); NOTICE("== SVC test build ==\n"); NOTICE("EEPROM holds values 0x%x, 0x%x and 0x%x\n", avs_step[0], avs_step[1], avs_step[2]); /* Override the AVS value? */ if ((ap_type != CHIP_ID_AP807) && (avs_step[1] < 0x33)) { /* AP806 - AVS is 7 bits */ new_wp = avs_step[1]; } else if (ap_type == CHIP_ID_AP807 && (avs_step[2] < 0x4)) { /* AP807 - AVS is 10 bits */ new_wp = avs_step[2]; new_wp <<= 8; new_wp |= avs_step[1]; } if (new_wp == 0) NOTICE("Ignore BAD AVS Override value in EEPROM!\n"); else NOTICE("Override AVS by EEPROM value 0x%x\n", new_wp); #endif /* MARVELL_SVC_TEST */ return new_wp; } /**************************************************************************** * SVC flow - v0.10 * The feature is intended to configure AVS value according to eFuse values * that are burned individually for each SoC during the test process. * Primary AVS value is stored in HD efuse and processed on power on * by the HW engine * Secondary AVS value is located in LD efuse and contains 4 work points for * various CPU frequencies. * The Secondary AVS value is only taken into account if the SW Revision stored * in the efuse is greater than 0 and the CPU is running in a certain speed. **************************************************************************** */ static void ble_plat_svc_config(void) { uint32_t reg_val, avs_workpoint, freq_pidi_mode; uint64_t efuse; uint32_t device_id, single_cluster; uint16_t svc[4], perr[4], i, sw_ver; unsigned int ap_type; /* Set access to LD0 */ avs_workpoint = avs_update_from_eeprom(0); if (avs_workpoint) goto set_aws_wp; /* Set access to LD0 */ reg_val = mmio_read_32(MVEBU_AP_EFUSE_SRV_CTRL_REG); reg_val &= ~EFUSE_SRV_CTRL_LD_SELECT_OFFS; mmio_write_32(MVEBU_AP_EFUSE_SRV_CTRL_REG, reg_val); /* Obtain the value of LD0[125:63] */ efuse = mmio_read_32(MVEBU_AP_LD0_125_95_EFUSE_OFFS); efuse <<= 32; efuse |= mmio_read_32(MVEBU_AP_LD0_94_63_EFUSE_OFFS); /* SW Revision: * Starting from SW revision 1 the SVC flow is supported. * SW version 0 (efuse not programmed) should follow the * regular AVS update flow. */ sw_ver = (efuse >> EFUSE_AP_LD0_SWREV_OFFS) & EFUSE_AP_LD0_SWREV_MASK; if (sw_ver < 1) { NOTICE("SVC: SW Revision 0x%x. SVC is not supported\n", sw_ver); #if MARVELL_SVC_TEST NOTICE("SVC_TEST: AVS bypassed\n"); #else ble_plat_avs_config(); #endif return; } /* Frequency mode from SAR */ freq_pidi_mode = SAR_CLOCK_FREQ_MODE( mmio_read_32( MVEBU_AP_SAR_REG_BASE( FREQ_MODE_AP_SAR_REG_NUM))); /* Decode all SVC work points */ svc[0] = (efuse >> EFUSE_AP_LD0_SVC1_OFFS) & EFUSE_AP_LD0_WP_MASK; svc[1] = (efuse >> EFUSE_AP_LD0_SVC2_OFFS) & EFUSE_AP_LD0_WP_MASK; svc[2] = (efuse >> EFUSE_AP_LD0_SVC3_OFFS) & EFUSE_AP_LD0_WP_MASK; /* Fetch AP type to distinguish between AP806 and AP807 */ ap_type = ble_get_ap_type(); if (ap_type != CHIP_ID_AP807) { svc[3] = (efuse >> EFUSE_AP_LD0_SVC4_OFFS) & EFUSE_AP_LD0_WP_MASK; INFO("SVC: Efuse WP: [0]=0x%x, [1]=0x%x, [2]=0x%x, [3]=0x%x\n", svc[0], svc[1], svc[2], svc[3]); } else { INFO("SVC: Efuse WP: [0]=0x%x, [1]=0x%x, [2]=0x%x\n", svc[0], svc[1], svc[2]); } /* Validate parity of SVC workpoint values */ for (i = 0; i < 4; i++) { uint8_t parity, bit; perr[i] = 0; for (bit = 1, parity = svc[i] & 1; bit < 7; bit++) parity ^= (svc[i] >> bit) & 1; /* Starting from SW version 2, the parity check is mandatory */ if ((sw_ver > 1) && (parity != ((svc[i] >> 7) & 1))) perr[i] = 1; /* register the error */ } single_cluster = mmio_read_32(MVEBU_AP_LD0_220_189_EFUSE_OFFS); single_cluster = (single_cluster >> EFUSE_AP_LD0_CLUSTER_DOWN_OFFS) & 1; device_id = cp110_device_id_get(MVEBU_CP_REGS_BASE(0)); if (device_id == MVEBU_80X0_DEV_ID || device_id == MVEBU_80X0_CP115_DEV_ID) { /* A8040/A8020 */ NOTICE("SVC: DEV ID: %s, FREQ Mode: 0x%x\n", single_cluster == 0 ? "8040" : "8020", freq_pidi_mode); switch (freq_pidi_mode) { case CPU_1800_DDR_1200_RCLK_1200: case CPU_1800_DDR_1050_RCLK_1050: if (perr[1]) goto perror; avs_workpoint = svc[1]; break; case CPU_1600_DDR_1050_RCLK_1050: case CPU_1600_DDR_900_RCLK_900_2: if (perr[2]) goto perror; avs_workpoint = svc[2]; break; case CPU_1300_DDR_800_RCLK_800: case CPU_1300_DDR_650_RCLK_650: if (perr[3]) goto perror; avs_workpoint = svc[3]; break; case CPU_2000_DDR_1200_RCLK_1200: case CPU_2000_DDR_1050_RCLK_1050: default: if (perr[0]) goto perror; avs_workpoint = svc[0]; break; } } else if (device_id == MVEBU_70X0_DEV_ID || device_id == MVEBU_70X0_CP115_DEV_ID) { /* A7040/A7020/A6040 */ NOTICE("SVC: DEV ID: %s, FREQ Mode: 0x%x\n", single_cluster == 0 ? "7040" : "7020", freq_pidi_mode); switch (freq_pidi_mode) { case CPU_1400_DDR_800_RCLK_800: if (single_cluster) {/* 7020 */ if (perr[1]) goto perror; avs_workpoint = svc[1]; } else { if (perr[0]) goto perror; avs_workpoint = svc[0]; } break; case CPU_1200_DDR_800_RCLK_800: if (single_cluster) {/* 7020 */ if (perr[2]) goto perror; avs_workpoint = svc[2]; } else { if (perr[1]) goto perror; avs_workpoint = svc[1]; } break; case CPU_800_DDR_800_RCLK_800: case CPU_1000_DDR_800_RCLK_800: if (single_cluster) {/* 7020 */ if (perr[3]) goto perror; avs_workpoint = svc[3]; } else { if (perr[2]) goto perror; avs_workpoint = svc[2]; } break; case CPU_600_DDR_800_RCLK_800: if (perr[3]) goto perror; avs_workpoint = svc[3]; /* Same for 6040 and 7020 */ break; case CPU_1600_DDR_800_RCLK_800: /* 7020 only */ default: if (single_cluster) {/* 7020 */ if (perr[0]) goto perror; avs_workpoint = svc[0]; } else avs_workpoint = 0; break; } } else if (device_id == MVEBU_3900_DEV_ID) { NOTICE("SVC: DEV ID: %s, FREQ Mode: 0x%x\n", "3900", freq_pidi_mode); switch (freq_pidi_mode) { case CPU_1600_DDR_1200_RCLK_1200: if (perr[0]) goto perror; avs_workpoint = svc[0]; break; case CPU_1300_DDR_800_RCLK_800: if (perr[1]) goto perror; avs_workpoint = svc[1]; break; default: if (perr[0]) goto perror; avs_workpoint = svc[0]; break; } } else { ERROR("SVC: Unsupported Device ID 0x%x\n", device_id); return; } /* Set AVS control if needed */ if (avs_workpoint == 0) { ERROR("SVC: AVS work point not changed\n"); return; } /* Remove parity bit */ if (ap_type != CHIP_ID_AP807) avs_workpoint &= 0x7F; /* Update WP from EEPROM if needed */ avs_workpoint = avs_update_from_eeprom(avs_workpoint); set_aws_wp: reg_val = mmio_read_32(AVS_EN_CTRL_REG); NOTICE("SVC: AVS work point changed from 0x%x to 0x%x\n", (reg_val & AVS_VDD_LOW_LIMIT_MASK) >> AVS_LOW_VDD_LIMIT_OFFSET, avs_workpoint); reg_val &= ~(AVS_VDD_LOW_LIMIT_MASK | AVS_VDD_HIGH_LIMIT_MASK); reg_val |= 0x1 << AVS_ENABLE_OFFSET; reg_val |= avs_workpoint << AVS_HIGH_VDD_LIMIT_OFFSET; reg_val |= avs_workpoint << AVS_LOW_VDD_LIMIT_OFFSET; mmio_write_32(AVS_EN_CTRL_REG, reg_val); return; perror: ERROR("Failed SVC WP[%d] parity check!\n", i); ERROR("Ignoring the WP values\n"); } #if PLAT_RECOVERY_IMAGE_ENABLE static int ble_skip_image_i2c(struct skip_image *skip_im) { ERROR("skipping image using i2c is not supported\n"); /* not supported */ return 0; } static int ble_skip_image_other(struct skip_image *skip_im) { ERROR("implementation missing for skip image request\n"); /* not supported, make your own implementation */ return 0; } static int ble_skip_image_gpio(struct skip_image *skip_im) { unsigned int val; unsigned int mpp_address = 0; unsigned int offset = 0; switch (skip_im->info.test.cp_ap) { case(CP): mpp_address = MVEBU_CP_GPIO_DATA_IN(skip_im->info.test.cp_index, skip_im->info.gpio.num); if (skip_im->info.gpio.num > NUM_OF_GPIO_PER_REG) offset = skip_im->info.gpio.num - NUM_OF_GPIO_PER_REG; else offset = skip_im->info.gpio.num; break; case(AP): mpp_address = MVEBU_AP_GPIO_DATA_IN; offset = skip_im->info.gpio.num; break; } val = mmio_read_32(mpp_address); val &= (1 << offset); if ((!val && skip_im->info.gpio.button_state == HIGH) || (val && skip_im->info.gpio.button_state == LOW)) { mmio_write_32(SCRATCH_PAD_REG2, SCRATCH_PAD_SKIP_VAL); return 1; } return 0; } /* * This function checks if there's a skip image request: * return values: * 1: (true) images request been made. * 0: (false) no image request been made. */ static int ble_skip_current_image(void) { struct skip_image *skip_im; /*fetching skip image info*/ skip_im = (struct skip_image *)plat_marvell_get_skip_image_data(); if (skip_im == NULL) return 0; /* check if skipping image request has already been made */ if (mmio_read_32(SCRATCH_PAD_REG2) == SCRATCH_PAD_SKIP_VAL) return 0; switch (skip_im->detection_method) { case GPIO: return ble_skip_image_gpio(skip_im); case I2C: return ble_skip_image_i2c(skip_im); case USER_DEFINED: return ble_skip_image_other(skip_im); } return 0; } #endif int ble_plat_setup(int *skip) { int ret; unsigned int freq_mode; /* Power down unused CPUs */ plat_marvell_early_cpu_powerdown(); /* * Save the current CCU configuration and make required changes: * - Allow access to DRAM larger than 4GB * - Open memory access to all CPn peripherals */ ble_plat_mmap_config(MMAP_SAVE_AND_CONFIG); #if PLAT_RECOVERY_IMAGE_ENABLE /* Check if there's a skip request to bootRom recovery Image */ if (ble_skip_current_image()) { /* close memory access to all CPn peripherals. */ ble_plat_mmap_config(MMAP_RESTORE_SAVED); *skip = 1; return 0; } #endif /* Do required CP-110 setups for BLE stage */ cp110_ble_init(MVEBU_CP_REGS_BASE(0)); /* Setup AVS */ ble_plat_svc_config(); /* read clk option from sampled-at-reset register */ freq_mode = SAR_CLOCK_FREQ_MODE(mmio_read_32(MVEBU_AP_SAR_REG_BASE( FREQ_MODE_AP_SAR_REG_NUM))); /* work with PLL clock driver in AP807 */ if (ble_get_ap_type() == CHIP_ID_AP807) ap807_clocks_init(freq_mode); /* Do required AP setups for BLE stage */ ap_ble_init(); /* Update DRAM topology (scan DIMM SPDs) */ plat_marvell_dram_update_topology(); /* Kick it in */ ret = dram_init(); /* Restore the original CCU configuration before exit from BLE */ ble_plat_mmap_config(MMAP_RESTORE_SAVED); return ret; }