The bl2_early_platform_setup() and bl2_platform_setup() were
redefined for Juno AArch32 eventhough CSS platform layer had
same definition for them. The CSS definitions definitions were
previously restricted to EL3_PAYLOAD_BASE builds and this is now
modified to include the Juno AArch32 builds as well thus
allowing us to remove the duplicate definitions in Juno platform
layer.
Change-Id: Ibd1d8c1428cc1d51ac0ba90f19f5208ff3278ab5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch does the required changes to enable CSS platforms
to build and use the SDS framework. Since SDS is always coupled with
SCMI protocol, the preexisting SCMI build flag is now renamed to
`CSS_USE_SCMI_SDS_DRIVER` which will enable both SCMI and SDS on
CSS platforms. Also some of the workarounds applied for SCMI are
now removed with SDS in place.
Change-Id: I94e8b93f05e3fe95e475c5501c25bec052588a9c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Before BL2 loads the SCP ram firmware, `SCP_BOOT_CFG_ADDR` specifies
the primary core. After the SCP ram firmware has started executing,
`SCP_BOOT_CFG_ADDR` is modified. This is not normally an issue but
the Juno AArch32 boot flow is a special case. BL1 does a warm reset
into AArch32 and the core jumps to the `sp_min` entrypoint. This is
effectively a `RESET_TO_SP_MIN` configuration. `sp_min` has to be
able to determine the primary core and hence we need to restore
`SCP_BOOT_CFG_ADDR` to the cold boot value before `sp_min` runs.
This magically worked when booting on A53 because the core index was
zero and it just so happened to match with the new value in
`SCP_BOOT_CFG_ADDR`.
Change-Id: I105425c680cf6238948625c1d1017b01d3517c01
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.
NOTE: Files that have been imported by FreeBSD have not been modified.
[0]: https://spdx.org/
Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Following steps are required to boot JUNO in AArch32 state:
1> BL1, in AArch64 state, loads BL2.
2> BL2, in AArch64 state, initializes DDR.
Loads SP_MIN & BL33 (AArch32 executable)images.
Calls RUN_IMAGE SMC to go back to BL1.
3> BL1 writes AArch32 executable opcodes, to load and branch
at the entrypoint address of SP_MIN, at HI-VECTOR address and
then request for warm reset in AArch32 state using RMR_EL3.
This patch makes following changes to facilitate above steps:
* Added assembly function to carry out step 3 above.
* Added region in TZC that enables Secure access to the
HI-VECTOR(0xFFFF0000) address space.
* AArch32 image descriptor is used, in BL2, to load
SP_MIN and BL33 AArch32 executable images.
A new flag `JUNO_AARCH32_EL3_RUNTIME` is introduced that
controls above changes. By default this flag is disabled.
NOTE: BL1 and BL2 are not supported in AArch32 state for JUNO.
Change-Id: I091d56a0e6d36663e6d9d2bb53c92c672195d1ec
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Soby Mathew
Dimitris Papastamos
Yatharth Kochar