The `arm-gic.h` file distributed by the Linux kernel is disjunctively
dual-licensed under the GPL-2.0 or MIT licenses, but the BSD-3-Clause
license has been applied in violation of the requirements of both
licenses. This change ensures the file is correctly licensed under the
terms of the MIT license, and that we comply with it by distributing a
copy of the license text.
Change-Id: Ie90066753a5eb8c0e2fc95ba43e3f5bcbe2fa459
Signed-off-by: Chris Kay <chris.kay@arm.com>
As per FF-A v1.0 spec, Table 3.1, messaging method field also contains
information about whether partition supports managed exit or not.
Since a partition can support managed exit only if it supports direct
messaging, so there are two new possible values, managed exit with only
direct messaging or with both messaging methods.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ic77cfb37d70975c3a36c56f8b7348d385735f378
By default the Arm Ethos-N NPU will boot up in secure mode. In this mode
the non-secure world cannot access the registers needed to use the NPU.
To still allow the non-secure world to use the NPU, a SiP service has
been added that can delegate non-secure access to the registers needed
to use it.
Only the HW_CONFIG for the Arm Juno platform has been updated to include
the device tree for the NPU and the platform currently only loads the
HW_CONFIG in AArch64 builds.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I65dfd864042ed43faae0a259dcf319cbadb5f3d2
To make it possible to use the hw_config device tree for dynamic
configuration in BL31 on the Arm Juno platform. A placeholder hw_config
has been added that is included in the FIP and a Juno specific BL31
setup has been added to populate fconf with the hw_config.
Juno's BL2 setup has been updated to align it with the new behavior
implemented in the Arm FVP platform, where fw_config is passed in arg1
to BL31 instead of soc_fw_config. The BL31 setup is expected to use the
fw_config passed in arg1 to find the hw_config.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: Ib3570faa6714f92ab8451e8f1e59779dcf19c0b6
Setting MSS_SUPPORT to 0 also removes requirement for SCP_BL2
definition.
Images build with MSS_SUPPORT=0 will not include service CPUs
FW and will not support PM, FC and other features implemented
in these FW images.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: Idf301ebd218ce65a60f277f3876d0aeb6c72f105
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/37769
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
This change adds a configuration for commitlint - a tool designed to
enforce a particular commit message style - and run it as part of Git's
commit-msg hook. This validates commits immediately after the editor has
been exited, and the configuration is derived from the configuration we
provide to Commitizen.
While the configuration provided suggests a maximum header and body
length, neither of these are hard errors. This is to accommodate the
occasional commit where it may be difficult or impossible to comply
with the length requirements (for example, with a particularly long
scope, or a long URL in the message body).
Change-Id: Ib5e90472fd1f1da9c2bff47703c9682232ee5679
Signed-off-by: Chris Kay <chris.kay@arm.com>
Husky is a tool for managing Git hooks within the repository itself.
Traditionally, commit hooks need to be manually installed on a per-user
basis, but Husky allows us to install these hooks either automatically
when `npm install` is invoked within the repository, or manually with
`npx husky install`.
This will become useful for us in the next few patches when we begin
introducing tools for enforcing a commit message style.
Change-Id: I64cae147e9ea910347416cfe0bcc4652ec9b4830
Signed-off-by: Chris Kay <chris.kay@arm.com>
Updated the documentation with latest Mbed TLS supported
version i.e. Mbed TLS v2.26.0
Fixes available in this version of Mbed TLS mainly affect
key generation/writing and certificates writing, which
are features used in the cert_create tool.
Release notes of Mbed TLSv2.26.0 are available here:
https://github.com/ARMmbed/mbedtls/releases/tag/v2.26.0
Change-Id: Ie15ee45d878b7681e15ec4bf64d54b416a31aa2f
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
CZ.NIC as part of Turris project released free and open source WTMI
application firmware 'wtmi_app.bin' for all Armada 3720 devices. This
firmware includes additional features like access to Hardware Random
Number Generator of Armada 3720 SoC which original Marvell's 'fuse.bin'
image does not have.
CZ.NIC's Armada 3720 Secure Firmware is available at website:
https://gitlab.nic.cz/turris/mox-boot-builder/
This change updates documentation to include steps how to build Marvell
firmware image for Espressobin with this firmware to enable Hardware
Random Number Generator on Espressobin.
In this change is fixed also URL to TF-A and U-Boot git repositories in
Espressobin build example. And as Marvell github repositories switched
default branch to master, explicit branch via -b parameter is redundant
and therefore from examples removed.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I59ee29cb6ed149264c5e4202f2af8f9ab3859418
Cortex A77 erratum 1946167 is a Cat B erratum that applies to revisions
<= r1p1. This erratum is avoided by inserting a DMB ST before acquire
atomic instructions without release semantics through a series of
writes to implementation defined system registers.
SDEN can be found here:
https://documentation-service.arm.com/static/600057a29b9c2d1bb22cd1be?token=
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I53e3b4fb7e7575ec83d75c2f132eda5ae0b4f01f
As per the new multi-console framework, updating the JTAG DCC support.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I77994ce387caf0d695986df3d01d414a920978d0
As per the new multi-console framework, updating the JTAG DCC support.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I62cfbb57ae7e454fbc91d1c54aafa6e99f9a35c8
The legacy console is gone. Re-add DCC console support based
on the multi-console framework.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Ia8388721093bc1be3af40974530d7c9a9ae5f43e
The new Allwinner H616 SoC lacks the management controller and the secure
SRAM A2, so we need to tweak the memory map quite substantially:
We run BL31 in DRAM. Since the DRAM starts at 1GB, we cannot use our
compressed virtual address space (max 256MB) anymore, so we revert to
the full 32bit VA space and use a flat mapping throughout all of it.
The missing controller also means we need to always use the native PSCI
ops, using the CPUIDLE hardware, as SCPI and suspend depend on the ARISC.
Change-Id: I77169b452cb7f5dc2ef734f3fc6e5d931749141d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Update the Allwinner platform documentation.
Reorder the section, to have the build instructions first, followed by
hints about the installation.
Add some ASCII art about the layout of our virtual memory map, which
uses a non-trivial condensed virtual address space.
Change-Id: Iaaa79b4366012394e15e4c1b26c212b5efb6ed6a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Adds bl2 with FIP to the build required for mbed Linux booting where
we do:
BootROM -> SPL -> BL2 -> OPTEE -> u-boot
If NEED_BL2 is specified then BL2 will be built and BL31 will have
its address range modified upwards to accommodate. BL31 must be
loaded from a FIP in this case.
If NEED_BL2 is not specified then the current BL31 boot flow is
unaffected and u-boot SPL will load and execute BL31 directly.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: I655343b3b689b1fc57cfbedda4d3dc2fbd549a96
Added GIC600AE FVP model version information.
Change-Id: I15d25fbdb8e09900976d5993032ec049f8db79f2
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
ARMv8.6 adds virtual offset registers to support virtualization of the
event counters in EL1 and EL0. This patch enables support for this
feature in EL3 firmware.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I7ee1f3d9f554930bf5ef6f3d492e932e6d95b217
Added a build option 'FVP_GICR_REGION_PROTECTION' to make
redistributor frame of fused/unused cores as read only.
Change-Id: Ie85f86e2465b93321a92a888ce8712a3144e4ccb
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
This adds the TRNG Firmware Interface Service to the standard
service dispatcher. This includes a method for dispatching entropy
requests to platforms and includes an entropy pool implementation to
avoid dropping any entropy requested from the platform.
Change-Id: I71cadb3cb377a507652eca9e0d68714c973026e9
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
* changes:
docs: marvell: Replace ESPRESSObin-Ultra TF-A build example by full example how to build production release of Marvell firmware image
docs: marvell: Fix description of flash-image.bin image
docs: marvell: Add information into CLOCKSPRESET option how to identify CPU frequency
docs: marvell: Reformat DDR_TOPOLOGY option and mention EspressoBin-Ultra board
docs: marvell: Move Supported Marvell platforms to PLAT build option
* changes:
docs: marvell: Update info about WTMI_IMG option
plat: marvell: armada: a3k: Remove unused variable WTMI_SYSINIT_IMG from Makefile
plat: marvell: armada: Show informative build messages and blank lines
plat: marvell: armada: Move definition of mrvl_flash target to common marvell_common.mk file
plat: marvell: armada: a3k: Use $(Q) instead of @
plat: marvell: armada: a3k: Add a new target mrvl_uart which builds UART image
plat: marvell: armada: a3k: Build UART image files directly in $(BUILD_UART) subdirectory
plat: marvell: armada: a3k: Build intermediate files in $(BUILD_PLAT) directory
plat: marvell: armada: a3k: Correctly set DDR_TOPOLOGY and CLOCKSPRESET for WTMI
plat: marvell: armada: a3k: Allow use of the system Crypto++ library
docs: marvell: Update info about WTP and MV_DDR_PATH parameters
plat: marvell: armada: a3k: Add checks that WTP, MV_DDR_PATH and CRYPTOPP_PATH are correctly defined
docs: marvell: Update mv-ddr-marvell and A3700-utils-marvell branches
ESPRESSObin-Ultra TF-A build example was now just a copy+paste of previous
mentioned example. It produced debug binary with custom log level, which
was not described. So rather replace this duplicate build example by a full
example with all steps how to build production release of Marvell firmware
image for EspressoBin with 1GHz CPU and 1GB DDR4 RAM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ief1b8bc96a3035ebd8421bd68dca5eb5c8d8fd52
Reformat list of boards, remove unsupported OcteonTX2 and mention
supported Turris MOX board.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I22cea7f77fd078554c7f0ed4108781626209e563
Default WTMI_IMG value was documented incorrectly. Also WTMI_IMG name may
be misleading as this option does not specify full WTMI image, just a main
loop (e.g. fuse.bin or custom RTOS image) without hardware initialization
code (DDR, CPU and clocks).
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I3de4a27ce2165b962fa628c992fd8f80151efd7c
This change separates building of flash and UART images, so it is possible
to build only one of these images. Also this change allows make to build
them in parallel.
Target mrvl_flash now builds only flash image and mrvl_uart only UART
image. This change reflects it also in the documentation.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ie9ce4538d52188dd26d99dfeeb5ad171a5b818f3
This change introduces two new A3720 parameters, CRYPTOPP_LIBDIR and
CRYPTOPP_INCDIR, which can be used to specify directory paths to
pre-compiled Crypto++ library and header files.
When both new parameters are specified then the source code of Crypto++ via
CRYPTOPP_PATH parameter is not needed. And therefore it allows TF-A build
process to use system Crypto++ library.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I6d440f86153373b11b8d098bb68eb7325e86b20b
Marvell finally started providing the latest version of mv-ddr-marvell and
A3700-utils-marvell code in master branch of their git repositories.
Reflect this in build instructions.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I08d1189dac60eb2a28335c68f611c1da634106f6
Chris Kay
Manish Pandey
Mark Dykes
Joanna Farley
Olivier Deprez
Mikael Olsson
Konstantin Porotchkin
Madhukar Pappireddy
Manish V Badarkhe
Pali Rohár
laurenw-arm
Venkatesh Yadav Abbarapu
André Przywara
Ying-Chun Liu (PaulLiu)
Mark Dykes
johpow01
Yann Gautier
Jimmy Brisson
Peng Fan