In preparation for adding support for Reference Design platforms
which have different base addresses for GIC Distributor or
Redistributor, move GIC related base addresses to individual platform
definition files.
Change-Id: Iecf52b4392a30b86905e1cd047c0ff87d59d0191
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Include multi-chip-mode parameter in HW_CONFIG dts to let next stage of
boot firmware know about the multi-chip operation mode.
Change-Id: Ic7535c2280fd57180ad14aa0ae277cf0c4d1337b
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
RD-N1-Edge based platforms can operate in dual-chip configuration
wherein two rdn1edge SoCs are connected through a high speed coherent
CCIX link.
This patch adds a function to check if the RD-N1-Edge platform is
operating in multi-chip mode by reading the SID register's NODE_ID
value. If operating in multi-chip mode, initialize GIC-600 multi-chip
operation by overriding the default GICR frames with array of GICR
frames and setting the chip 0 as routing table owner.
The address space of the second RD-N1-Edge chip (chip 1) starts from the
address 4TB. So increase the physical and virtual address space size to
43 bits to accommodate the multi-chip configuration. If the multi-chip
mode configuration is detected, dynamically add mmap entry for the
peripherals memory region of the second RD-N1-Edge SoC. This is required
to let the BL31 platform setup stage to configure the devices in the
second chip.
PLATFORM_CORE_COUNT macro is set to be multiple of CSS_SGI_CHIP_COUNT
and topology changes are added to represent the dual-chip configuration.
In order the build the dual-chip platform, CSS_SGI_CHIP_COUNT macro
should be set to 2:
export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all
Change-Id: I576cdaf71f0b0e41b9a9181fa4feb7091f8c7bb4
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.
Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.
Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
AFF3 bits of MPIDR corresponds to Chip-Id in Arm multi-chip platforms.
For calculating linear core position of CPU cores from slave chips, AFF3
bits has to be used. Update `plat_arm_calc_core_pos` assembly function
to include AFF3 bits in calculation.
Change-Id: I4af2bd82ab8e31e18bc61de22705a73893954260
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Some of the Reference Design platforms like RD-N1-Edge can operate in
multi-chip configuration wherein two or more SoCs are connected through
a high speed coherent CCIX link. For the RD platforms, the remote chip
address space is at the offset of 4TB per chip. In order for the primary
chip to access the device memory region on the remote chip, the required
memory region entries need to be added as mmap entry. This patch adds
macros related to the remote chip device memory region.
Change-Id: I833810b96f1a0e7c3c289ac32597b6ba03344c80
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Multi-chip platforms have two or more identical chips connected using a
high speed coherent link. In order to identify such platforms,
add chip_id and multi_chip_mode information in the platform variant
info structure. The values of these two new elements is populated
during boot.
Change-Id: Ie6e89cb33b3f0f408814f6239cd06647053e23ed
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
For SGI-575 and RD platforms, move bl31_platform_setup handler to
individual board files to allow the platforms to perform board specific
bl31 setup.
Change-Id: Ia44bccc0a7f40a155b33909bcb438a0909b20d42
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Introduce macro 'CSS_SGI_CHIP_COUNT' to allow Arm CSS platforms with
multi-chip support to define number of chiplets on the platform. By
default, this flag is set to 1 and does not affect the existing single
chip platforms.
For multi-chip platforms, override the default value of
CSS_SGI_CHIP_COUNT with the number of chiplets supported on the
platform. As an example, the command below sets the number of chiplets
to two on the RD-N1-Edge multi-chip platform:
export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all
Change-Id: If364dc36bd34b30cc356f74b3e97633933e6c8ee
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
The platform topology description of the upcoming Arm's RD platforms
have different topology than those listed in the sgi_topology.c file. So
instead of adding platform specific topology into existing
sgi_topology.c file, those can be added to respective board files. In
order to maintain consistency with the upcoming platforms, move the
existing platform topology description to respective board files.
Change-Id: I4689c7d24cd0c75a3dc234370c34a85c08598abb
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
As on SGI platforms, SCPI is unsupported on SGM platforms.
Change-Id: I556ed095b9eb55b72447230ee2725d3c76160a08
Signed-off-by: Chris Kay <chris.kay@arm.com>
NOTE for platform integrators:
API `plat_psci_stat_get_residency()` third argument
`last_cpu_idx` is changed from "signed int" to the
"unsigned int" type.
Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.
2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent
Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.
Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c
The contents of this header have been merged into the spm_mm_svc.h
header file.
Change-Id: I01530b2e4ec1b4c091ce339758025e2216e740a4
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Before adding any new SPM-related components we should first do
some cleanup around the existing SPM-MM implementation. The aim
is to make sure that any SPM-MM components have names that clearly
indicate that they are MM-related. Otherwise, when adding new SPM
code, it could quickly become confusing as it would be unclear to
which component the code belongs.
The secure_partition.h header is a clear example of this, as the
name is generic so it could easily apply to any SPM-related code,
when it is in fact SPM-MM specific.
This patch renames the file and the two structures defined within
it, and then modifies any references in files that use the header.
Change-Id: I44bd95fab774c358178b3e81262a16da500fda26
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
The Secure Partition Manager (SPM) prototype implementation is
being removed. This is preparatory work for putting in place a
dispatcher component that, in turn, enables partition managers
at S-EL2 / S-EL1.
This patch removes:
- The core service files (std_svc/spm)
- The Resource Descriptor headers (include/services)
- SPRT protocol support and service definitions
- SPCI protocol support and service definitions
Change-Id: Iaade6f6422eaf9a71187b1e2a4dffd7fb8766426
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
There are two different implementations of Secure Partition
management in TF-A. One is based on the "Management Mode" (MM)
design, the other is based on the Secure Partition Client Interface
(SPCI) specification. Currently there is a dependency between their
build flags that shouldn't exist, making further development
harder than it should be. This patch removes that
dependency, making the two flags function independently.
Before: ENABLE_SPM=1 is required for using either implementation.
By default, the SPCI-based implementation is enabled and
this is overridden if SPM_MM=1.
After: ENABLE_SPM=1 enables the SPCI-based implementation.
SPM_MM=1 enables the MM-based implementation.
The two build flags are mutually exclusive.
Note that the name of the ENABLE_SPM flag remains a bit
ambiguous - this will be improved in a subsequent patch. For this
patch the intention was to leave the name as-is so that it is
easier to track the changes that were made.
Change-Id: I8e64ee545d811c7000f27e8dc8ebb977d670608a
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
This patch invokes the new function gicv3_rdistif_probe() in the
ARM platform specific gicv3 driver. Since this API modifies the
shared GIC related data structure, it must be invoked coherently
by using the platform specific pwr_domain_on_finish_late hook.
Change-Id: I6efb17d5da61545a1c5a6641b8f58472b31e62a8
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
NOTE: __ASSEMBLY__ macro is now deprecated in favor of __ASSEMBLER__.
All common C compilers predefine a macro called __ASSEMBLER__ when
preprocessing a .S file. There is no reason for TF-A to define it's own
__ASSEMBLY__ macro for this purpose instead. To unify code with the
export headers (which use __ASSEMBLER__ to avoid one extra dependency),
let's deprecate __ASSEMBLY__ and switch the code base over to the
predefined standard.
Change-Id: Id7d0ec8cf330195da80499c68562b65cb5ab7417
Signed-off-by: Julius Werner <jwerner@chromium.org>
Fixed the path to a source file specified in tsp makefile
Created a platform specific tsp makefile
Change-Id: I89565127c67eff510e48e21fd450af4c3088c2d4
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.
So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.
Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
There is a bug in the shared heap implementation for SGM. Until the bug
is solved, the default implementation is used.
Change-Id: I010911a3f00ed860f742b14daad1d99b9e7ce711
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
The weak version of plat_get_mbedtls_heap() was being used.
Change-Id: I6da331a098dd1af5bb64729d5b914cfb74b8869e
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
This file is used when building the cert_create tool without using
the 'standard' set of Arm OID values as defined in the TBBR
specification (see tbbr_oid.h). This configuration is enabled by
setting USE_TBBR_DEFS to 0 during build.
At the moment this will fail because the header file included by
this file was removed in commit bb41eb7a9d ("cert: move
platform_oid.h to include/tools_share for all platforms"). For
the SGM platform this means that there is no current use for
this file.
Change-Id: I3c82983ada62330f1ab6be6d6c0cf489adabae7b
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Improved support for W=1 compilation flag by solving missing-prototypes
and old-style-definition warnings.
The libraries are compiling with warnings (which turn into errors with
the Werror flag).
Outside of libraries, some warnings cannot be fixed without heavy
structural changes.
Change-Id: I1668cf99123ac4195c2a6a1d48945f7a64c67f16
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
MHU doorbell driver requires arm platform specific
macro "PLAT_CSS_MHU_BASE".
Rename it to "PLAT_MHUV2_BASE", so that platforms other than arm
can use generic MHU doorbell driver.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Replace all uses of 'SGI_CLARK' with 'RD_N1E1_EDGE' and
'SGI_CLARK_HELIOS' with 'RD_E1_EDGE' as per the updated product
names
Change-Id: Ib8136e421b1a46da1e5df58c6b1432d5c78d279b
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Many parts of the code were duplicating symbols that are defined in
include/common/bl_common.h. It is better to only use the definitions in
this header.
As all the symbols refer to virtual addresses, they have to be
uintptr_t, not unsigned long. This has also been fixed in bl_common.h.
Change-Id: I204081af78326ced03fb05f69846f229d324c711
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Use full include paths like it is done for common includes.
This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.
Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
On ARM platforms, the BL2 memory can be overlaid by BL31/BL32. The memory
descriptors describing the list of executable images are created in BL2
R/W memory, which could be possibly corrupted later on by BL31/BL32 due
to overlay. This patch creates a reserved location in SRAM for these
descriptors and are copied over by BL2 before handing over to next BL
image.
Also this patch increases the PLAT_ARM_MAX_BL2_SIZE for juno when TBBR
is enabled.
FixesARM-Software/tf-issues#626
Change-Id: I755735706fa702024b4032f51ed4895b3687377f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
Corrects typos in core code, documentation files, drivers, Arm
platforms and services.
None of the corrections affect code; changes are limited to comments
and other documentation.
Change-Id: I5c1027b06ef149864f315ccc0ea473e2a16bfd1d
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.
This also prevents problems like cyclic dependencies.
Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The definitions in bl1/bl1_private.h and bl2/bl2_private.h are useful for
platforms that may need to access them.
Change-Id: Ifd1880f855ddafcb3bfcaf1ed4a4e0f121eda174
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Update some asserts that refer to #defines that only occur in
ARM platforms, preventing this code to be used on other platforms.
Instead, use a platform agnostic name, and update all the existing
users.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This patch removes the dependency of the N1SDP on soc
css defines in order to let the N1SDP platform port
define the uart related constants.
Change-Id: If13796f278586a01512ee99615502b30e478189e
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>
Aditya Angadi
Vijayenthiran Subramaniam
Zelalem
Manish Pandey
Chris Kay
Deepika Bhavnani
Paul Beesley
Madhukar Pappireddy
Julius Werner
John Tsichritzis
Antonio Niño Díaz
Ambroise Vincent
Masahisa Kojima
Chandni Cherukuri
Sathees Balya
Soby Mathew
Ard Biesheuvel
Deepak Pandey