On GICv3 systems, as a side effect of adding provision to handle EL3
interrupts (unconditionally routing FIQs to EL3), pending Non-secure
interrupts (signalled as FIQs) may preempt execution in lower Secure ELs
[1]. This will inadvertently disrupt the semantics of Fast SMC
(previously called Atomic SMC) calls.
To retain semantics of Fast SMCs, the GIC PMR must be programmed to
prevent Non-secure interrupts from preempting Secure execution. To that
effect, two new functions in the Exception Handling Framework subscribe
to events introduced in an earlier commit:
- Upon 'cm_exited_normal_world', the Non-secure PMR is stashed, and
the PMR is programmed to the highest Non-secure interrupt priority.
- Upon 'cm_entering_normal_world', the previously stashed Non-secure
PMR is restored.
The above sequence however prevents Yielding SMCs from being preempted
by Non-secure interrupts as intended. To facilitate this, the public API
exc_allow_ns_preemption() is introduced that programs the PMR to the
original Non-secure PMR value. Another API
exc_is_ns_preemption_allowed() is also introduced to check if
exc_allow_ns_preemption() had been called previously.
API documentation to follow.
[1] On GICv2 systems, this isn't a problem as, unlike GICv3, pending NS
IRQs during Secure execution are signalled as IRQs, which aren't
routed to EL3.
Change-Id: Ief96b162b0067179b1012332cd991ee1b3051dd0
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Acknowledging interrupt shall return a raw value from the interrupt
controller in which the actual interrupt ID may be encoded. Add a
platform API to extract the actual interrupt ID from the raw value
obtained from interrupt controller.
Document the new function. Also clarify the semantics of interrupt
acknowledge.
Change-Id: I818dad7be47661658b16f9807877d259eb127405
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Some SoCs integrate a GIC in version 1 that is currently not supported
by the trusted firmware. This change hijacks GICv2 driver to handle the
GICv1 as GICv1 is compatible enough with GICv2 as far as the platform
does not attempt to play with virtualization support or some GICv2
specific power features.
Note that current trusted firmware does not use these GICv2 features
that are not available in GICv1 Security Extension.
Change-Id: Ic2cb3055f1319a83455571d6d918661da583f179
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
For Trusted Board Boot, BL2 needs more space to support the ECDSA
and ECDSA+RSA algorithms.
Change-Id: Ie7eda9a1315ce836dbc6d18d6588f8d17891a92d
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>
An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.
This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms. The
deprecated interrupt list definitions are however retained to support
legacy builds.
Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.
NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.
Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The GIC driver initialization currently allows an array of interrupts to
be configured as secure. Future use cases would require more interrupt
configuration other than just security, such as priority.
This patch introduces a new interrupt property array as part of both
GICv2 and GICv3 driver data. The platform can populate the array with
interrupt numbers and respective properties. The corresponding driver
initialization iterates through the array, and applies interrupt
configuration as required.
This capability, and the current way of supplying array (or arrays, in
case of GICv3) of secure interrupts, are however mutually exclusive.
Henceforth, the platform should supply either:
- A list of interrupts to be mapped as secure (the current way).
Platforms that do this will continue working as they were. With this
patch, this scheme is deprecated.
- A list of interrupt properties (properties include interrupt group).
Individual interrupt properties are specified via. descriptors of
type 'interrupt_prop_desc_t', which can be populated with the macro
INTR_PROP_DESC().
A run time assert checks that the platform doesn't specify both.
Henceforth the old scheme of providing list of secure interrupts is
deprecated. When built with ERROR_DEPRECATED=1, GIC drivers will require
that the interrupt properties are supplied instead of an array of secure
interrupts.
Add a section to firmware design about configuring secure interrupts.
FixesARM-software/tf-issues#262
Change-Id: I8eec29e72eb69dbb6bce77879febf32c95376942
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The helpers perform read-modify-write on GIC*_ICFGR registers, but don't
serialise callers. Any serialisation must be taken care of by the
callers.
Change-Id: I71995f82ff2c7f70d37af0ede30d6ee18682fd3f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
SPIs can be routed to either a specific PE, or to any one of all
available PEs.
API documentation updated.
Change-Id: I28675f634568aaf4ea1aa8aa7ebf25b419a963ed
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The back end GIC driver converts and assigns the interrupt type to
suitable group.
For GICv2, a build option GICV2_G0_FOR_EL3 is introduced, which
determines to which type Group 0 interrupts maps to.
- When the build option is set 0 (the default), Group 0 interrupts are
meant for Secure EL1. This is presently the case.
- Otherwise, Group 0 interrupts are meant for EL3. This means the SPD
will have to synchronously hand over the interrupt to Secure EL1.
The query API allows the platform to query whether the platform supports
interrupts of a given type.
API documentation updated.
Change-Id: I60fdb4053ffe0bd006b3b20914914ebd311fc858
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
These APIs allow the GIC implementation to categorize interrupt numbers
into SPIs, PPIs, and SGIs. The default implementations for GICv2 and
GICv3 follows interrupt numbering as specified by the ARM GIC
architecture.
API documentation updated.
Change-Id: Ia6aa379dc955994333232e6138f259535d4fa087
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The PE target mask is used to translate linear PE index (returned by
platform core position) to a bit mask used when targeting interrupts to
a PE, viz. when raising SGIs and routing SPIs.
The platform shall:
- Populate the driver data with a pointer to array that's to contain
per-PE target masks.
- Invoke the new driver API 'gicv2_set_pe_target_mask()' during
per-CPU initialization so that the driver populates the target mask
for that CPU.
Platforms that don't intend to target interrupts or raise SGIs need not
populate this.
Change-Id: Ic0db54da86915e9dccd82fff51479bc3c1fdc968
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Document the API in separate platform interrupt controller API document.
Change-Id: If18f208e10a8a243f5c59d226fcf48e985941949
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch adds functions to save and restore GICv3 ITS registers during
system suspend. Please note that the power management of GIC ITS is
implementation defined. These functions only implements the
architectural part of the ITS power management and they do not restore
memory structures or register content required to support ITS. Even if
the ITS implementation stores structures in memory, an implementation
defined power down sequence is likely to be required to flush some
internal ITS caches to memory. If such implementation defined sequence
is not followed, the platform must ensure that the ITS is not power
gated during system suspend.
Change-Id: I5f31e5541975aa7dcaab69b0b7f67583c0e27678
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
During system suspend, the GICv3 Distributor and Redistributor context
can be lost due to power gating of the system power domain. This means
that the GICv3 context needs to be saved prior to system suspend and
restored on wakeup. Currently the consensus is that the Firmware should
be in charge of this. See tf-issues#464 for more details.
This patch introduces helper APIs in the GICv3 driver to save and
restore the Distributor and Redistributor contexts. The GICv3 ITS
context is not considered in this patch because the specification says
that the details of ITS power management is implementation-defined.
These APIs are expected to be appropriately invoked by the platform
layer during system suspend.
FixesARM-software/tf-issues#464
Change-Id: Iebb9c6770ab8c4d522546f161fa402d2fe02ec00
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
Add new option rsa+ecdsa for TF_MBEDTLS_KEY_ALG, which selects
rsa or ecdsa depending on the certificate used.
Change-Id: I08d9e99bdbba361ed2ec5624248dc382c750ad47
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>
The type `unsigned long` is 32 bit wide in AArch32, but 64 bit wide in
AArch64. This is inconsistent and that's why we avoid using it as per
the Coding Guidelines. This patch changes all `UL` occurrences to `U`
or `ULL` depending on the context so that the size of the constant is
clear.
This problem affected the macro `BIT(nr)`. As long as this macro is used
to fill fields of registers, that's not a problem, since all registers
are 32 bit wide in AArch32 and 64 bit wide in AArch64. However, if the
macro is used to fill the fields of a 64-bit integer, it won't be able
to set the upper 32 bits in AArch32.
By changing the type of this macro to `unsigned long long` the behaviour
is always the same regardless of the architecture, as this type is
64-bit wide in both cases.
Some Tegra platform files have been modified by this patch.
Change-Id: I918264c03e7d691a931f0d1018df25a2796cc221
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The driver has only one API: to initialize an SMMUv3 device. This
operates on a device that implements secure state, by invalidating
secure caches and TLBs.
Change-Id: Ief32800419ddf0f1fe38c8f0da8f5ba75c72c826
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The current build system and driver requires the CCI product to be
specified at build time. The device constraints can be determined at run
time from its ID registers, obviating the need for specifying them
ahead.
This patch adds changes to identify and validate CCI at run time. Some
global variables are renamed to be in line with the rest of the code
base.
The build option ARM_CCI_PRODUCT_ID is now removed, and user guide is
updated.
Change-Id: Ibb765e349d3bc95ff3eb9a64bde1207ab710a93d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This fix modifies the order of system includes to meet the ARM TF coding
standard. There are some exceptions in order to retain header groupings,
minimise changes to imported headers, and where there are headers within
the #if and #ifndef statements.
Change-Id: I65085a142ba6a83792b26efb47df1329153f1624
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>
This patch adds header files with required declarations and
macro definitions to enable integration with CryptoCell SBROM
version `CC712 – Release 1.0.0.1061`. These headers enable ARM
Trusted Firmware to build and link with CryptoCell SBROM
library.
Change-Id: I501eda7fe1429acb61db8e1cab78cc9aee9c1871
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch uses the U() and ULL() macros for constants, to fix some
of the signed-ness defects flagged by the MISRA scanner.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch adds support for RSASSA-PSS Signature Algorithm for
X509 certificates in mbedtls crypto driver. Now the driver supports
RSA PKCS2_1 standard as mandated by TBBR.
NOTE: With this patch, the PKCS1_5 standard compliant RSA signature
is deprecated.
Change-Id: I9cf6d073370b710cc36a7b374a55ec96c0496461
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
If UFS device is initialized, we could just make it out of
hibernation by UFS_FLAGS_SKIPINIT. And vendor's dirver is always
focus on PHY setting. We could use UFS driver directly if it
exits from hibernation.
There're eight LUNs in UFS device. The UFS driver only provides
the read/write API with LUN. User could define his own read/write
since user may want to access different LUNs.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The Trusted Firmware uses a subset of the APIs provided by mbed TLS.
This subset internally uses `snprintf`, but the only format specifier
used is '%d', which is supported by `tf_snprintf`.
This patch makes mbed TLS use `tf_snprintf` instead of `snprintf`,
saving 3 KB in both debug and release builds when TBBR is enabled.
Change-Id: I7f992a21015930d7c0f4660e7a28ceefd60b9597
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
An earlier patch (arm-trusted-firmware#874) migrated MBEDTLS_ suffixed
macros to have a TBBR_ suffix to avoid any potential clash with future
mbedtls macros.
But on reflection the TBBR_ suffix could be confusing as the macros
are used to drive TF-specific configuration of mbedtls. As such
this patch migrates these macros from TBBR_suffix to TF_MBEDTLS_
suffix which more accurately conveys their use.
Change-Id: Ic87642b653ceeaa03d62f724976abd5e12e867d4
Signed-off-by: David Cunado <david.cunado@arm.com>
To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.
NOTE: Files that have been imported by FreeBSD have not been modified.
[0]: https://spdx.org/
Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
This function ensures that console output is flushed, for example
before shutting down or use by another component
In line with other console APIs, console_flush() wraps
console_core_flush().
Also implement console_core_flush() for PL011.
Change-Id: I3db365065e4de04a454a5c2ce21be335a23a01e4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
These macros are not part of mbed TLS so they should not be prefixed
with `MBEDTLS_` to avoid potential collision in the future. Use the
`TBBR_` suffix to highlight that they only used in TF.
`MBEDTLS_KEY_ALG` was not modified because that is documented and used
by platforms to select the key algorithm.
Change-Id: Ief224681715c481691c80810501830ce16e210b0
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
tbz check for RDR status is to check for a bit being zero.
Unfortunately, we are using a mask rather than the bit position.
Further as per http://www.ti.com/lit/ds/symlink/pc16550d.pdf (page 17),
LSR register bit 0 is Data ready status (RDR), not bit position 2.
Update the same to match the specification.
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Some GICv3 implementations have provision for power management
operations at Redistributor level. This patch introduces and provides
place-holders for Redistributor power management. The default
implementations are empty stubs, but are weakly bound so as to enable
implementation-specific drivers to override them.
Change-Id: I4fec1358693d3603ca5dce242a2f7f0e730516d8
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Some files have incorrect copyright notices, this patch fixes all
files with deviations from the standard notice.
Change-Id: I66b73e78a50a235acb55f1e2ec2052a42c0570d2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
C99 restricts bitfields type is signed and unsigned integer or _Bool.
See section 6.7.2.1 Structure and union specifiers.
"A bit-field shall have a type that is a qualified or unqualified version
of _Bool, signed int, unsigned int, or some other implementation-defined type."
Since the compiler packs bitfields anyways, actual data layout in the structure is unaffected.
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Support CMD23. When CMD23 is used, CMD12 could be avoided.
Two scenarios:
1. CMD17 for single block, CMD18 + CMD12 for multiple blocks.
2. CMD23 + CMD18 for both single block and multiple blocks.
The emmc_init() should initialize whether CMD23 is supported
or not.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
This patch fixes the offset of GICD_IROUTER register defined in gicv3.h.
Although the GICv3 documention mentions that the offset for this register
is 0x6100-0x7FD8, the offset calculation for an interrupt id `n` is :
0x6000 + 8n, where n >= 32
This requires the offset for GICD_IROUTER to be defined as 0x6000.
FixesARM-software/tf-issues#410
Change-Id: If9e91e30d946afe7f1f60fea4f065c7567093fa8
This patch reworks type usage in generic code, drivers and ARM platform files
to make it more portable. The major changes done with respect to
type usage are as listed below:
* Use uintptr_t for storing address instead of uint64_t or unsigned long.
* Review usage of unsigned long as it can no longer be assumed to be 64 bit.
* Use u_register_t for register values whose width varies depending on
whether AArch64 or AArch32.
* Use generic C types where-ever possible.
In addition to the above changes, this patch also modifies format specifiers
in print invocations so that they are AArch64/AArch32 agnostic. Only files
related to upcoming feature development have been reworked.
Change-Id: I9f8c78347c5a52ba7027ff389791f1dad63ee5f8
On some platform gpio can set/get pull status when input, add these
function so we can set/get gpio pull status when need it. And they are
optional function.
This patch adds the API `ccn_get_part0_id` to query the PART0 ID from the
PERIPHERAL_ID 0 register in the CCN driver. This ID allows to distinguish
the variant of CCN present on the system and possibly enable dynamic
configuration of the IP based on the variant. Also added an assert in
`ccn_master_to_rn_id_map()` to ensure that the master map bitfield provided
by the platform is within the expected interface id.
Change-Id: I92d2db7bd93a9be8a7fbe72a522cbcba0aba2d0e
Add delay timer implementation based on the system generic counter.
This either uses the platform's implementation of
`plat_get_syscnt_freq()` or explicit clock multiplier/divider values
provided by the platform.
The current implementation of udelay has been modified to avoid
unnecessary calculations while waiting on the loop and to make it
easier to check for overflows.
Change-Id: I9062e1d506dc2f68367fd9289250b93444721732
Allow to handle cases where some images are pre-loaded (by debugger for
instance) without introducing many switches in files calling load_* functions.
Fixes: arm-software/tf-issues#398
Signed-off-by: Gerald Lejeune <gerald.lejeune@st.com>
In a lot of embedded platforms, eMMC device is the only one storage
device. So loading content from eMMC device is required in ATF.
Create the emmc stack that could co-work with IO block driver.
Support to read/write/erase eMMC blocks on both rpmb and normal
user area. Support to change the IO speed and bus width.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
FIP is accessed as memory-mapped type. eMMC is block device type.
In order to support FIP based on eMMC, add the new io_block layer.
io_block always access eMMC device as block size. And it'll only
copy the required data into buffer in io_block driver. So preparing
an temporary buffer is required.
When use io_block device, MAX_IO_BLOCK_DEVICES should be declared
in platform_def.h. It's used to support multiple block devices.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Currently the `tzc400_configure_region` and `tzc_dmc500_configure_region`
functions uses uintptr_t as the data type for `region_top` and `region_base`
variables, which will be converted to 32/64 bits for AArch32/AArch64
respectively. But the expectation is to keep these addresses at least 64 bit.
This patch modifies the data types to make it at least 64 bit by using
unsigned long long instead of uintptr_t for the `region_top` and
`region_base` variables. It also modifies the associated macros
`_tzc##fn_name##_write_region_xxx` accordingly.
Change-Id: I4e3c6a8a39ad04205cf0f3bda336c3970b15a28b
The ARM CoreLink DMC-500 Dynamic Memory Controller provides the
programmable address region control of a TrustZone Address Space
Controller. The access permissions can be defined for eight
separate address regions plus a background or default region.
This patch adds a DMC-500 driver to define address regions and
program their access permissions as per ARM 100131_0000_02_en
(r0p0) document.
Change-Id: I9d33120f9480d742bcf7937e4b876f9d40c727e6
TrustZone protection can be programmed by both memory and TrustZone
address space controllers like DMC-500 and TZC-400. These peripherals
share a similar programmer's view.
Furthermore, it is possible to have multiple instances of each type of
peripheral in a system resulting in multiple programmer's views.
For example, on the TZC-400 each of the 4 filter units can be enabled
or disabled for each region. There is a single set of registers to
program the region attributes. On the DMC-500, each filter unit has its
own programmer's view resulting in multiple sets of registers to program
the region attributes. The layout of the registers is almost the same
across all these variations.
Hence the existing driver in `tzc400\tzc400.c` is refactored into the
new driver in `tzc\tzc400.c`. The previous driver file is still maintained
for compatibility and it is now deprecated.
Change-Id: Ieabd0528e244582875bc7e65029a00517671216d
This patch adds support for non-volatile counter authentication to
the Authentication Module. This method consists of matching the
counter values provided in the certificates with the ones stored
in the platform. If the value from the certificate is lower than
the platform, the boot process is aborted. This mechanism protects
the system against rollback.
The TBBR CoT has been updated to include this method as part of the
authentication process. Two counters are used: one for the trusted
world images and another for the non trusted world images.
** NEW PLATFORM APIs (mandatory when TBB is enabled) **
int plat_get_nv_ctr(void *cookie, unsigned int *nv_ctr);
This API returns the non-volatile counter value stored
in the platform. The cookie in the first argument may be
used to select the counter in case the platform provides
more than one (i.e. TBSA compliant platforms must provide
trusted and non-trusted counters). This cookie is specified
in the CoT.
int plat_set_nv_ctr(void *cookie, unsigned int nv_ctr);
This API sets a new counter value. The cookie may be
used to select the counter to be updated.
An implementation of these new APIs for ARM platforms is also
provided. The values are obtained from the Trusted Non-Volatile
Counters peripheral. The cookie is used to pass the extension OID.
This OID may be interpreted by the platform to know which counter
must return. On Juno, The trusted and non-trusted counter values
have been tied to 31 and 223, respectively, and cannot be modified.
** IMPORTANT **
THIS PATCH BREAKS THE BUILD WHEN TRUSTED_BOARD_BOOT IS ENABLED. THE
NEW PLATFORM APIs INTRODUCED IN THIS PATCH MUST BE IMPLEMENTED IN
ORDER TO SUCCESSFULLY BUILD TF.
Change-Id: Ic943b76b25f2a37f490eaaab6d87b4a8b3cbc89a
This patch moves the private GIC common accessors from `gic_common.h` to
a new private header file `gic_common_private.h`. This patch also adds
additional comments to GIC register accessors to highlight the fact
that some of them access register values that correspond to multiple
interrupt IDs. The convention used is that the `set`, `get` and `clr`
accessors access and modify the values corresponding to a single interrupt
ID whereas the `read` and `write` GIC register accessors access the raw
GIC registers and it could correspond to multiple interrupt IDs depending
on the register accessed.
Change-Id: I2643ecb2533f01e3d3219fcedfb5f80c120622f9
The code to set the interrupt priority for secure interrupts in the
new GICv2 and GICv3 drivers is incorrect. The setup code to configure
interrupt priorities of secure interrupts, one interrupt at a time, used
gicd_write_ipriorityr()/gicr_write_ipriority() function affecting
4 interrupts at a time. This bug did not manifest itself because all the
secure interrupts were configured to the highest secure priority(0) during
cold boot and the adjacent non secure interrupt priority would be configured
later by the normal world. This patch introduces new accessors,
gicd_set_ipriorityr() and gicr_set_ipriorityr(), for configuring priority
one interrupt at a time and fixes the the setup code to use the new
accessors.
FixesARM-software/tf-issues#344
Change-Id: I470fd74d2b7fce7058b55d83f604be05a27e1341
The PL011 TRM (ARM DDI 0183G) specifies that the UART must be
disabled before any of the control registers are programmed. The
PL011 driver included in TF does not disable the UART, so the
initialization in BL2 and BL31 is violating this requirement
(and potentially in BL1 if the UART is enabled after reset).
This patch modifies the initialization function in the PL011
console driver to disable the UART before programming the
control registers.
Register clobber list and documentation updated.
FixesARM-software/tf-issues#300
Change-Id: I839b2d681d48b03f821ac53663a6a78e8b30a1a1
Migrate all direct usage of __attribute__ to usage of their
corresponding macros from cdefs.h.
e.g.:
- __attribute__((unused)) -> __unused
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Use the new __deprecated macro from the generic cdefs header and remove
the deprecated __warn_deprecated.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
This patch rearranges fields of the `image_desc_t` & `auth_img_desc_t`
data structures to reduce padding between the fields and thereby
save memory.
NOTE: Platform ports which anonymously initialize these structures
should be aware of the rearrangement and do the required
modification.
Change-Id: I428b5429632797b31d5bd306174599c07e24c060
By default ARM TF is built with the '-pedantic' compiler flag, which
helps detecting violations of the C standard. However, the mbed TLS
library and its associated authentication module in TF used to fail
building with this compiler flag. As a workaround, the mbed TLS
authentication module makefile used to set the 'DISABLE_PEDANTIC'
TF build flag.
The compiler errors flagged by '-pedantic' in the mbed TLS library
have been fixed between versions 1.3.9 and 2.2.0 and the library now
properly builds with this compiler flag.
This patch fixes the remaining compiler errors in the mbed TLS
authentication module in TF and unsets the 'DISABLE_PEDANTIC' TF
build flag. This means that TF is now always built with '-pedantic'.
In particular, this patch:
* Removes the final semi-colon in REGISTER_COT() macro.
This semi-colon was causing the following error message:
drivers/auth/tbbr/tbbr_cot.c:544:23: error: ISO C does not allow
extra ';' outside of a function [-Werror=pedantic]
This has been fixed both in the mbed TLS authentication module
as well as in the certificate generation tool. Note that the latter
code didn't need fixing since it is not built with '-pedantic' but
the change has been propagated for consistency.
Also fixed the REGISTER_KEYS() and REGISTER_EXTENSIONS() macros,
which were suffering from the same issue.
* Fixes a pointer type.
It was causing the following error message:
drivers/auth/mbedtls/mbedtls_crypto.c: In function 'verify_hash':
drivers/auth/mbedtls/mbedtls_crypto.c:177:42: error: pointer of
type 'void *' used in arithmetic [-Werror=pointer-arith]
Change-Id: I7b7a04ef711efd65e17b5be26990d1a0d940257d
The mbed TLS library has introduced some changes in the API from
the 1.3.x to the 2.x releases. Using the 2.x releases requires
some changes to the crypto and transport modules.
This patch updates both modules to the mbed TLS 2.x API.
All references to the mbed TLS library in the code or documentation
have been updated to 'mbed TLS'. Old references to PolarSSL have
been updated to 'mbed TLS'.
User guide updated to use mbed TLS 2.2.0.
NOTE: moving up to mbed TLS 2.x from 1.3.x is not backward compatible.
Applying this patch will require an mbed TLS 2.x release to be used.
Also note that the mbed TLS license changed to Apache version 2.0.
Change-Id: Iba4584408653cf153091f2ca2ee23bc9add7fda4
The Server Base System Architecture document (ARM-DEN-0029)
specifies a generic UART device. The programmer's view of this
generic UART is a subset of the ARM PL011 UART. However, the
current PL011 driver in Trusted Firmware uses some features
that are outside the generic UART specification.
This patch modifies the PL011 driver to exclude features outside
the SBSA generic UART specification by setting the boolean build
option 'PL011_GENERIC_UART=1'. Default value is 0 (use full
PL011 features).
User guide updated.
FixesARM-software/tf-issues#216
Change-Id: I6e0eb86f9d69569bc3980fb57e70d6da5d91a737
Allowing console base address to be set to NULL conveniently
allows console driver to ignore further invocations to console_putc()
and console_getc(). This patch adds `console_uninit()` API to the
console driver which sets console base address as NULL. The BL images can
invoke this API to finish the use of console and ignore any further
invocations to print to the console.
Change-Id: I00a1762b3e0b7c55f2be2f9c4c9bee3967189dde
Add compile time `__warn_deprecated` flag to public api's in CCI-400
specific driver so that user is aware of the driver being deprecated.
Similarly, it also adds an error message when `ERROR_DEPRECATED` is set
to prevent succesful compilation if CCI-400 specific driver is used.
Change-Id: Id7e61a560262abc01cbbd432ca85b9bf448a194d
This patch renames the GICv3 interrupt group macros from
INT_TYPE_G0, INT_TYPE_G1S and INT_TYPE_G1NS to INTR_GROUP0,
INTR_GROUP1S and INTR_GROUP1NS respectively.
Change-Id: I40c66f589ce6234fa42205adcd91f7d6ad8f33d4
This patch fixes several issues with the SP804 delay timer on FVP:
* By default, the SP804 dual timer on FVP runs at 32 KHz. In order
to run the timer at 35 MHz (as specified in the FVP user manual)
the Overwrite bit in the SP810 control register must be set.
* The CLKMULT and CLKDIV definitions are mixed up:
delta(us) = delta(ticks) * T(us) = delta(ticks) / f(MHz)
From the delay function:
delta_us = (delta * ops->clk_mult) / ops->clk_div;
Matching both expressions:
1 / f(MHz) = ops->clk_mult / ops->clk_div
And consequently:
f(MHz) = ops->clk_div / ops->clk_mult
Which, for a 35 MHz timer, translates to:
ops->clk_div = 35
ops->clk_mult = 1
* The comment in the delay timer header file has been corrected:
The ratio of the multiplier and the divider is the clock period
in microseconds, not the frequency.
Change-Id: Iffd5ce0a5a28fa47c0720c0336d81b678ff8fdf1
The TZC-400 driver implementation incorrectly uses the component
ID registers to detect the TZC-400 peripheral. As all ARM
peripherals share the same component ID, it doesn't allow to
uniquely identify the TZC-400 peripheral. This patch fixes the
TZC-400 driver by relying on the `part_number_0` and
`part_number_1` fields in the `PID` registers instead.
The `tzc_read_component_id` function has been replaced by
`tzc_read_peripheral_id`, which reads the 'part_number' values
and compares them with the TZC-400 peripheral ID.
Also, it adds a debug assertion to detect when the TZC driver
initialisation function is called multiple times.
Change-Id: I35949f6501a51c0a794144cd1c3a6db62440dce6
Based on SP805 Programmer's model (ARM DDI 0270B). This driver
provides three public APIs:
void sp805_start(uintptr_t base, unsigned long ticks);
void sp805_stop(uintptr_t base);
void sp805_refresh(uintptr_t base, unsigned long ticks);
Upon start, the watchdog starts counting down from the number of
ticks specified. When the count reaches 0 an interrupt is triggered.
The watchdog restarts counting down from the number of ticks
specified. If the count reaches 0 again, the system is reset. A
mechanism to handle the interrupt has not been implemented. Instead,
the API to refresh the watchdog should be used instead to prevent a
system reset.
Change-Id: I799d53f8d1213b10b341a4a67fde6486e89a3dab
This patch deprecates the legacy ARM GIC driver and related header files
(arm_gic.h, gic_v2.h, gic_v3.h). For GICv2 systems, platform ports should
use the GICv2 driver in include/drivers/arm/gicv2.h and for GICv3 systems,
platform ports should use the GICv3 driver in include/drivers/arm/gicv3.h
NOTE: The ARM Legacy GIC drivers have been deprecated with this patch.
Platform ports are encouraged to migrate to the new GIC drivers.
Change-Id: Ic0460ef0427b54a6aac476279a7f29b81943e942
This patch adds a driver for ARM GICv2 systems, example GIC-400. Unlike
the existing GIC driver in `include/drivers/arm/arm_gic.h`, this driver
is optimised for GICv2 and does not support GICv3 systems in GICv2
compatibility mode. The driver interface has been implemented in
`drivers/arm/gic/v2/gicv2_main.c`. The corresponding header is in
`include/drivers/arm/gicv2.h`. Helper functions are implemented in
`drivers/arm/gic/v2/gicv2_helpers.c` and are accessible through the
`drivers/arm/gic/v2/gicv2_private.h` header.
Change-Id: I09fffa4e621fb99ba3c01204839894816cd89a2a
This patch adds a driver for ARM GICv3 systems that need to run software
stacks where affinity routing is enabled across all privileged exception
levels for both security states. This driver is a partial implementation
of the ARM Generic Interrupt Controller Architecture Specification, GIC
architecture version 3.0 and version 4.0 (ARM IHI 0069A). The driver does
not cater for legacy support of interrupts and asymmetric configurations.
The existing GIC driver has been preserved unchanged. The common code for
GICv2 and GICv3 systems has been refactored into a new file,
`drivers/arm/gic/common/gic_common.c`. The corresponding header is in
`include/drivers/arm/gic_common.h`.
The driver interface is implemented in `drivers/arm/gic/v3/gicv3_main.c`.
The corresponding header is in `include/drivers/arm/gicv3.h`. Helper
functions are implemented in `drivers/arm/gic/v3/arm_gicv3_helpers.c`
and are accessible through the `drivers/arm/gic/v3/gicv3_private.h`
header.
Change-Id: I8c3c834a1d049d05b776b4dcb76b18ccb927444a
Patch 7e26fe1f deprecates IO specific return definitions in favour
of standard errno codes. This patch removes those definitions
and its usage from the IO framework, IO drivers and IO platform
layer. Following this patch, standard errno codes must be used
when checking the return value of an IO function.
Change-Id: Id6e0e9d0a7daf15a81ec598cf74de83d5768650f
This patch redefines the values of IO_FAIL, IO_NOT_SUPPORTED and
IO_RESOURCES_EXHAUSTED to match the corresponding definitions in
errno.h:
#define IO_FAIL (-ENOENT)
#define IO_NOT_SUPPORTED (-ENODEV)
#define IO_RESOURCES_EXHAUSTED (-ENOMEM)
NOTE: please note that the IO_FAIL, IO_NOT_SUPPORTED and
IO_RESOURCES_EXHAUSTED definitions are considered deprecated
and their usage should be avoided. Callers should rely on errno.h
definitions when checking the return values of IO functions.
Change-Id: Ic8491aa43384b6ee44951ebfc053a3ded16a80be
The generic delay timer driver expects a pointer to a timer_ops_t
structure containing the specific timer driver information. It
doesn't make a copy of the structure, instead it just keeps the
pointer. Therefore, this pointer must remain valid over time.
The SP804 driver doesn't satisfy this requirement. The
sp804_timer_init() macro creates a temporary instanciation of the
timer_ops_t structure on the fly and passes it to the generic
delay timer. When this temporary instanciation gets deallocated,
the generic delay timer is left with a pointer to invalid data.
This patch fixes this bug by statically allocating the SP804
timer_ops_t structure.
Change-Id: I8fbf75907583aef06701e3fd9fabe0b2c9bc95bf
This patch adds a device driver which can be used to program the following
aspects of ARM CCN IP:
1. Specify the mapping between ACE/ACELite/ACELite+DVM/CHI master interfaces and
Request nodes.
2. Add and remove master interfaces from the snoop and dvm
domains.
3. Place the L3 cache in a given power state.
4. Configuring system adress map and enabling 3 SN striping mode of memory
controller operation.
Change-Id: I0f665c6a306938e5b66f6a92f8549b529aa8f325
Currently, on ARM platforms(ex. Juno) non-secure access to specific
peripheral regions, config registers which are inside and outside CSS
is done in the soc_css_security_setup(). This patch separates the CSS
security setup from the SOC security setup in the css_security_setup().
The CSS security setup involves programming of the internal NIC to
provide access to regions inside the CSS. This is needed only in
Juno, hence Juno implements it in its board files as css_init_nic400().
Change-Id: I95a1fb9f13f9b18fa8e915eb4ae2f15264f1b060
Jeenu Viswambharan
Etienne Carriere
Qixiang Xu
Soby Mathew
davidcunado-arm
Antonio Nino Diaz
Isla Mitchell
Varun Wadekar
danh-arm
Haojian Zhuang
dp-arm
Nishanth Menon
Qixiang.Xu
Caesar Wang
Gerald Lejeune
Yatharth Kochar
Soren Brinkmann
Vikram Kanigiri
Juan Castillo
Sandrine Bailleux
Achin Gupta
Juan Castillo