Currently only UART0 is handled as console device, fix the
code to support UART1 as console also.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I08f69b65b78b967ceb7159f4a467aa5982b1f791
With new gcc11.2 by default the -mbranch-protection is
set to "standard" which is leading to increase the text
section by 4Kb. As the ZynqMP uses the ARMv8 architecture,
so there is no impact when we disable the branch protection.
These instructions do not provide the branch protection in
architectures before Armv8.3-A.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I36f7a55abf99f50df2ee265255598d83b1f480c6
Add support for runtime feature configuration which are running on the
firmware. Add new IOCTL IDs like IOCTL_SET_FEATURE_CONFIG and
IOCTL_GET_FEATURE_CONFIG for configuring the features.
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I976aef15932783a25396b2adeb4c8f140cc87e79
Sync IOCTL IDs in order to avoid conflict with other components like,
Linux and firmware. Hence assigning value to IDs to make it more
specific.
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I11ae679fbd0a953290306b62d661cc142f50dc28
All API calls except non-blocking should wait for
IPI response and read buffer to check return status
from firmware. Some of API calls are not reading
status from IPI payload data. Use sync method which
reads actual return status from IPI payload.
Signed-off-by: Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
Change-Id: I78f9c061a80cee6d524ade4ef124ca88ce1848cf
As there is constraint with the space for the release builds,
remove some of the legacy code.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I5b8b16f34ed8e480f16ab1aeac80b85cdb391852
In case of TF-A running out of DDR there is a need to reserved
memory to let other SW know that none can't use this memory. HW
wise this region can be (and should be) also protected by
protection unit XMPU. This is the first step to add reserved
memory location to DT.
DT address corresponds with default address in U-Boot and also
default address in Xilinx BSPs.
Code is valid only when TF-A runs out of DDR. When it runs out
of OCM there is no need to reseve anything because OCM is hidden
to OS.
Change-Id: I01f230ced67207a159128cc11d11d36dd4590cab
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add basic SDEI support, implementing the software event 0 only for now.
This already allows hypervisors like Jailhouse to use SDEI for internal
signaling while passing the GICC through to the guest (see also IMX8).
With SDEI on, we overrun the SRAM and need to stay in DRAM. So keep SDEI
off by default.
Co-developed-by: Angelo Ruocco <angeloruocco90@gmail.com>
Signed-off-by: Angelo Ruocco <angeloruocco90@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Change-Id: Ic0d71b4ef0978c0a34393f4e3530ed1e24a39ca2
Add support for XCK26 silicon which is available on SOM board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: Ic98213328702903af8a79f487a2868f3e6d60338
Counter frequency for generic timer of Arm-A53 based Application
Processing Unit(APU) is not configuring in case if First Stage Boot
Loader(FSBL) does not initialize counter frequency. This happens
when FSBL is running from Arm-R5 based Real-time Processing Unit(RPU).
Because of that generic timer driver functionality is not working.
So configure counter frequency during initialization.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Icfccd59d7d2340fba25ebfb2ef6a813af4290896
Rename the macro ZYNQMP_IPI_CRC_CHECK to IPI_CRC_CHECK and
move the related defines to the common include.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I6d30b081ac607572a0b23e10ca8031bc90489e58
As per the new multi-console framework, updating the JTAG DCC support.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I62cfbb57ae7e454fbc91d1c54aafa6e99f9a35c8
Add support for ZU43DR, ZU46DR and ZU47DR to the list of zynqmp
devices. The ZU43DR, ZU46DR and ZU47DR RFSoC silicon id values are
0x7d, 0x78 and 0x7f.
Signed-off-by: Sandeep Gundlupet Raju <sandeep.gundlupet-raju@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I566f707116d83475de7c87a6004ca96bf7bccebe
Removing the custom crash implementation and use
plat/common/aarch64/crash_console_helpers.S.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I045d42eb62bcaf7d1e18fbe9ab9fb9470e800215
Add ability to support PS and System reset after idling the APU,
by reading the restart scope from the PMU.
Signed-off-by: Will Wong <willw@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I23c01725d8ebb71ad34be02ab204411b93620702
ATF is not checking PM version. Add version check in such
a way that it is compatible with current and newer version
of PM.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Ia095d118121e6f75e8d320e87d5e2018068fa079
This patch fixes the non compliant code like missing braces for
conditional single statement bodies.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I95b410ae5950f85dc913c4448fcd0a97e0fd490c
Adding the EM specific smc handler for the EM-related requests.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I98122d49604a01a2f6bd1e509a5896ee68069dd0
This patch adds new api to access zynqmp efuse memory
Signed-off-by: VNSL Durga <vnsl.durga.challa@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I0971ab6549552a6f96412431388d19b822db00ab
This patch adds new zynqmp-pm api to provide read/write access to
CSU or PMU global registers.
Signed-off-by: Kalyani Akula <kalyania@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I4fd52eb732fc3e6a8bccd96cad7dc090b2161042
Functions are reimplemented to issue system-level pinctrl EEMI calls
to the PMU-FW rather than using MMIO read/write. Macros and functions
that appear to be unused after the change is made are removed.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I51f2285a79f202cb2ca9f031044002e16dd1e92f
Functions are reimplemented to issue system-level pinctrl EEMI calls
to the PMU-FW rather than using MMIO read/write. Macros and functions
that appear to be unused after the change is made are removed.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I21b8fda855aa69090b85d6aaf411e19560201cb5
The calls are just passed through to the PMU-FW. Before issuing
other pinctrl functions the pin should be successfully requested.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Ibce280edebedf779b3962009c274d0b3d928e0e4
In pm_query_data() function return type is stored in response so
there is no use of return type. Update return type of function
pm_query_data() from enum pm_ret_status to void. Similarly
update return type of pm_api_clock_get_name() and
pm_api_pinctrl_get_function_name() functions.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Id811926f0b4ebcc472480bb94f3b88109eb036cd
This patch disable the ITAPDLYENA bit for ITAP delay value zero.
As per IP design, it is recommended to disable the ITAPDLYENA bit
before auto-tuning.
Also disable OTAPDLYENA bit always as there is one issue in RTL
where SD0_OTAPDLYENA has been wrongly connected to both SD0 and SD1
controllers. Hence it is recommended to disable OTAPDLYENA bit always
for both the controllers.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Acked-by: Srinivas Goud <srinivas.goud@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Icf035cb63510ac7bec4e9d523a622f145eaf0989
This patch check for the DLL status before doing the DLL reset.
If DLL reset is already issued then skip the reset inside ATF
otherwise DLL reset will be issued.
By doing this way, all the following cases will be supported.
1. Patched ATF + Patched Linux base.
2. Older ATF + Patched Linux base.
3. Patched ATF + Older Linux base.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I53a0a27521330f1543275cc9cb44cd1dfc569c65
Current implementation doesn't support change of div1 value if clk
has 2 divisor because div1 clk is the parent of the div2 clk and div2
clk does not have SET_RATE_PARENT flag.
This causes div1 value to be fixed and only value of div2 will be
adjusted according to required clock rate.
Example:
Consider a case of nand_ref clock which has 2 divisor and 1 mux.
The frequency of mux clock is 1500MHz and default value of div1 and
div2 is 15 and 1 respectively. So the final clock will be of 100MHz.
When driver requests 80MHz for nand_ref clock, clock framework will
adjust the div2 value to 1 (setting div2 value 2 results final clock
to 50MHz which is more inaccurate compare to 100Mhz) which results
final clock to 100MHz.
Ideally the value of div1 and div2 should be updated to 19 and 1
respectively so that final clock goes to around 78MHz.
This patch fixes above problem by allowing change in div1 value.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Ibb98f6748d28653fdd1e59bf433b6a37ce9c1a58
This patches copies only the valid part of string and
avoids filling junk at the end.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: If23772f31f9cf7f5042e8bfc474fbfe77dcd90e7
Save some space by enabling the log messages like bl33 address
only for debug builds. Also check the bl33 and bl32 address and
print only if this is not NULL.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I58d846bf69a75e839eb49abcbb9920af13296886
For boot health status PMU Global General Storage Register 4 is
used. GGS4 can be used for other purpose along with boot health
status. So, change its name from PM_BOOT_HEALTH_STATUS_REG
to PMU_GLOBAL_GEN_STORAGE4.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I2f5c4c6a161121e7cdb4b9f0f8711d0dad16c372
Update the xilinx platform makefile to include GICv2 makefile
instead of adding the individual files. Updating this change
as per the latest changes done in the commit #1322dc94f7.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I79d8374c47a7f42761d121522b32ac7a5021ede8
From GCC-9 implementation of switch case was generated through jump tables,
because of which we are seeing 1MB increase in rodata section. To reduce
the size we are recommending to use fno-jump-tables.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I069733610809b8299fbf641f0ae35b359a8afd69
All EEMI error codes start with value 2000.
Note: Legacy error codes ARGS (=1) and NOTSUPPORTED (=4) returned by
current ATF code have been left in place.
Signed-off-by: Davorin Mista <davorin.mista@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I939afa85957cac88025d82a80f9f6dd49be993b6
Linux clock framework cannot properly deal with these errors. When the
error is related to the lack of permissions to control the clock we
filter the error and report the success to linux. Before recent changes
in clock framework across the stack, this was done in the PMU-FW as a
workaround. Since the PMU-FW now handles clocks and the permissions to
control them using general principles rather than workarounds, it can
no longer distinguish such exceptions and it has to return no-access
error.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I1491a80e472f44e322a542b29a20eb1cb3319802
And from crash_console_flush.
We ignore the error information return by console_flush in _every_
place where we call it, and casting the return type to void does not
work around the MISRA violation that this causes. Instead, we collect
the error information from the driver (to avoid changing that API), and
don't return it to the caller.
Change-Id: I1e35afe01764d5c8f0efd04f8949d333ffb688c1
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Moved SMCCC defines from plat_arm.h to new <smccc_def.h> header
and include this header in all ARM platforms.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I4cbc69c7b9307461de87b7c7bf200dd9b810e485
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I9f8b55414ab7965e431e3e86d182eabd511f32a4
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To find result count use ARRAY_SIZE for better readability.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: I97201de4d43024e59fa78bd61937c86d47724ab5
ATF handover can be used by Xilinx platforms, so move it to common
file from platform specific files.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I5f0839351f534619de581d1953c8427a079487e0
Move pm_client.h to common directory to avoid duplication
of function declaration.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: Iea542e681f42db089cccd9b24d286ac8f0a2ce35
As IPI mailbox service is common to both ZynqMP and Versal,
move it to xilinx/common.
Signed-off-by: Wendy Liang <wendy.liang@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: I1a7008ccf7930829621147922d2c6d8d46df5502
- Flag GICV2_G0_FOR_EL3 needs to be set for group interrupts
to be targeted to EL3.
- Raise SGI interrupts for individual CPU cores as GIC API
uses CPU num as parameter, not CPU mask.
- Flag WARMBOOT_ENABLE_DCACHE_EARLY needs to be set to enable
CPU interface mask work properly for all CPU cores which is
required when generating SGI.
- Call plat_ic_end_of_interrupt() from ttc_fiq_handler() to clear
GIC interrupt to avoid same interrupt again.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Change-Id: I71d4935b8d4688a3729c62753ca8a1a77cd92ae7
Venkatesh Yadav Abbarapu
Ronak Jain
Abhyuday Godhasara
Madhukar Pappireddy
Michal Simek
Jan Kiszka
Manish Pandey
Rajan Vaja
Will Wong
VNSL Durga
Kalyani Akula
Mirela Simonovic
Sai Krishna Potthuri
Ravi Patel
Siva Durga Prasad Paladugu
Tejas Patel
Davorin Mista
Jimmy Brisson
Manish V Badarkhe
Andre Przywara
Mark Dykes
Deepika Bhavnani
Norbert Werner
Wendy Liang