The PE target mask is used to translate linear PE index (returned by
platform core position) to a bit mask used when targeting interrupts to
a PE, viz. when raising SGIs and routing SPIs.
The platform shall:
- Populate the driver data with a pointer to array that's to contain
per-PE target masks.
- Invoke the new driver API 'gicv2_set_pe_target_mask()' during
per-CPU initialization so that the driver populates the target mask
for that CPU.
Platforms that don't intend to target interrupts or raise SGIs need not
populate this.
Change-Id: Ic0db54da86915e9dccd82fff51479bc3c1fdc968
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Document the API in separate platform interrupt controller API document.
Change-Id: If18f208e10a8a243f5c59d226fcf48e985941949
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch fixes an assertion check in the GICv3 ITS helper function.
Change-Id: I75f50d7bf6d87c12c6e24a07c9a9889e5facf4a5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds functions to save and restore GICv3 ITS registers during
system suspend. Please note that the power management of GIC ITS is
implementation defined. These functions only implements the
architectural part of the ITS power management and they do not restore
memory structures or register content required to support ITS. Even if
the ITS implementation stores structures in memory, an implementation
defined power down sequence is likely to be required to flush some
internal ITS caches to memory. If such implementation defined sequence
is not followed, the platform must ensure that the ITS is not power
gated during system suspend.
Change-Id: I5f31e5541975aa7dcaab69b0b7f67583c0e27678
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
During system suspend, the GICv3 Distributor and Redistributor context
can be lost due to power gating of the system power domain. This means
that the GICv3 context needs to be saved prior to system suspend and
restored on wakeup. Currently the consensus is that the Firmware should
be in charge of this. See tf-issues#464 for more details.
This patch introduces helper APIs in the GICv3 driver to save and
restore the Distributor and Redistributor contexts. The GICv3 ITS
context is not considered in this patch because the specification says
that the details of ITS power management is implementation-defined.
These APIs are expected to be appropriately invoked by the platform
layer during system suspend.
FixesARM-software/tf-issues#464
Change-Id: Iebb9c6770ab8c4d522546f161fa402d2fe02ec00
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
Tidy up the code a bit by turning some macros into inline functions
which allows to remove the do/while(0) idiom and backslashes at the end
of the line.
Change-Id: Ie41a4ea4a4da507f7b925247b53e85019101d717
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
Reindent the file using tabs as the mix of spaces and tabs confuses some
editors and leads them to use spaces instead of tabs for new code
although the coding style mandates tabs.
Change-Id: I87fa4a5d368a048340054b9b3622325f3f7befba
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
The type `unsigned long` is 32 bit wide in AArch32, but 64 bit wide in
AArch64. This is inconsistent and that's why we avoid using it as per
the Coding Guidelines. This patch changes all `UL` occurrences to `U`
or `ULL` depending on the context so that the size of the constant is
clear.
This problem affected the macro `BIT(nr)`. As long as this macro is used
to fill fields of registers, that's not a problem, since all registers
are 32 bit wide in AArch32 and 64 bit wide in AArch64. However, if the
macro is used to fill the fields of a 64-bit integer, it won't be able
to set the upper 32 bits in AArch32.
By changing the type of this macro to `unsigned long long` the behaviour
is always the same regardless of the architecture, as this type is
64-bit wide in both cases.
Some Tegra platform files have been modified by this patch.
Change-Id: I918264c03e7d691a931f0d1018df25a2796cc221
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The driver has only one API: to initialize an SMMUv3 device. This
operates on a device that implements secure state, by invalidating
secure caches and TLBs.
Change-Id: Ief32800419ddf0f1fe38c8f0da8f5ba75c72c826
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The current build system and driver requires the CCI product to be
specified at build time. The device constraints can be determined at run
time from its ID registers, obviating the need for specifying them
ahead.
This patch adds changes to identify and validate CCI at run time. Some
global variables are renamed to be in line with the rest of the code
base.
The build option ARM_CCI_PRODUCT_ID is now removed, and user guide is
updated.
Change-Id: Ibb765e349d3bc95ff3eb9a64bde1207ab710a93d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
ARM GIC-600 IP complies with ARM GICv3 architecture, but among others,
implements a power control register in the Redistributor frame. This
register must be programmed to mark the frame as powered on, before
accessing other registers in the frame. Rest of initialization sequence
remains the same.
The driver provides APIs for Redistributor power management, and
overrides those in the generic GICv3 driver. The driver data is shared
between generic GICv3 driver and that of GIC-600.
For FVP platform, the GIC-600 driver is chosen when FVP_USE_GIC_DRIVER
is set to FVP_GIC600. Also update user guide.
Change-Id: I321b2360728d69f6d4b0a747b2cfcc3fe5a20d67
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.
NOTE: Files that have been imported by FreeBSD have not been modified.
[0]: https://spdx.org/
Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Many asserts depend on code that is conditionally compiled based on the
DEBUG define. This patch modifies the conditional inclusion of such code
so that it is based on the ENABLE_ASSERTIONS build option.
Change-Id: I6406674788aa7e1ad7c23d86ce94482ad3c382bd
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
C files shouldn't be included into others. This file only contains some
macros and functions that can be made `static inline`, so it is ok to
convert it into a header file.
This is the only occurrence of a C file being included in another one in
the codebase instead of using a header, other occurrences are a way of
achieving backwards-compatibility.
Functions therein have been qualified as `inline`.
Change-Id: I88fe300f6d85a7f0740ef14c9cb8fa54849218e6
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The amount of console output is controlled by the LOG_LEVEL build
option. Using tf_printf without any #ifdef depending on the LOG_LEVEL
doesn't give the user that flexibility.
This patch replaces all occurrences of tf_printf that prints error, but
aren't dependent on LOG_LEVEL, with the ERROR macro.
Change-Id: Ib5147f14fc1579398a11f19ddd0e840ff6692831
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This function ensures that console output is flushed, for example
before shutting down or use by another component
In line with other console APIs, console_flush() wraps
console_core_flush().
Also implement console_core_flush() for PL011.
Change-Id: I3db365065e4de04a454a5c2ce21be335a23a01e4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Due to incorrect conditional compilation checks, bakery locks were
excluded from the CCN driver and the power controller driver for FVP
when BL32 was built as the EL3 Runtime Software in AArch32 mode.
This patch corrects the same.
Change-Id: Ib1f163d9167a5c38e4d622232c4835cad9c235aa
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The GIC driver data is initialized by the primary CPU with caches
enabled. When the secondary CPU boots up, it initializes the
GICC/GICR interface with the caches disabled and there is a chance that
the driver data is not yet written back to the memory. This patch fixes
this problem by flushing the driver data after they have been
initialized.
Change-Id: Ie9477029683846209593ff005d2bac559bb8f5e6
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
One nasty part of ATF is some of boolean macros are always defined
as 1 or 0, and the rest of them are only defined under certain
conditions.
For the former group, "#if FOO" or "#if !FOO" must be used because
"#ifdef FOO" is always true. (Options passed by $(call add_define,)
are the cases.)
For the latter, "#ifdef FOO" or "#ifndef FOO" should be used because
checking the value of an undefined macro is strange.
Here, IMAGE_BL* is handled by make_helpers/build_macro.mk like
follows:
$(eval IMAGE := IMAGE_BL$(call uppercase,$(3)))
$(OBJ): $(2)
@echo " CC $$<"
$$(Q)$$(CC) $$(TF_CFLAGS) $$(CFLAGS) -D$(IMAGE) -c $$< -o $$@
This means, IMAGE_BL* is defined when building the corresponding
image, but *undefined* for the other images.
So, IMAGE_BL* belongs to the latter group where we should use #ifdef
or #ifndef.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We are duplicating this macro define, and it is useful enough
to be placed in the common place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some GICv3 implementations have provision for power management
operations at Redistributor level. This patch introduces and provides
place-holders for Redistributor power management. The default
implementations are empty stubs, but are weakly bound so as to enable
implementation-specific drivers to override them.
Change-Id: I4fec1358693d3603ca5dce242a2f7f0e730516d8
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch makes following miscellaneous fixes:
* pl011_console.S: Fixed the bit mask used to check if the
transmit FIFO is full or empty.
* smcc_macros.S: Added `_fsxc` suffix while updating the SPSR.
By default the assembler assumes `_fc` suffix which does not
update all the fields in SPSR. By adding `_fsxc` suffix all
the fields gets updated.
* platform_helpers.S: Removed the weak definition for
`plat_my_core_pos()` as this is a mandatory function which
needs to be defined by all platforms.
Change-Id: I8302292533c943686fff8d7c749a07132c052a3b
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Currently the GICv3 driver mandates that platform populate
both G1S and G0 interrupts. However, it is possible that a
given platform is not interested in both the groups and
just needs to specify either one of them.
This patch modifies the `gicv3_rdistif_init()` & `gicv3_distif_init()`
functions to allow either G1S or G0 interrupts to be configured.
FixesARM-software/tf-issues#400
Change-Id: I43572b0e08ae30bed5af9334f25d35bf439b0d2b
As per the GICv3 specification, to power down a processor using GICv3
and allow automatic power-on if an interrupt must be sent to a processor,
software must set Enable to zero for all interrupt groups(by writing to
GICC_CTLR or ICC_IGRPEN{0,1}_EL1/3 as appropriate.
Also, NonSecure EL1 software may not be aware of the CPU power state
details and fail to choose right states that require quiescing the CPU
interface. So it's preferred that the PSCI implementation handles it as
it is fully aware of the CPU power states.
This patch adds disabling of Group1 NonSecure interrupts during processor
power down along with Group0 and Group1 Secure interrupts so that all the
interrupt groups are handled at once as per specification.
Change-Id: Ib564d773c9c4c41f2ca9471451c030e3de75e641
This patch modifies GICv3 and TZC drivers to add AArch32 support.
No modifications are required for the GICv2 driver for AArch32 support.
The TZC driver assumes that the secure world is running in Little-Endian
mode to do 64 bit manipulations. Assertions are present to validate the
assumption.
Note: The legacy GICv3 driver is not supported for AArch32.
Change-Id: Id1bc75a9f5dafb9715c9500ca77b4606eb1e2458
This patch moves the various assembly console drivers
into `aarch64` architecture specific folder. Stub files,
which include files from new location, are retained at the
original location for platform compatibility reasons.
Change-Id: I0069b6c1c0489ca47f5204d4e26e3bc3def533a8
This patch fixes the offset of GICD_IROUTER register defined in gicv3.h.
Although the GICv3 documention mentions that the offset for this register
is 0x6100-0x7FD8, the offset calculation for an interrupt id `n` is :
0x6000 + 8n, where n >= 32
This requires the offset for GICD_IROUTER to be defined as 0x6000.
FixesARM-software/tf-issues#410
Change-Id: If9e91e30d946afe7f1f60fea4f065c7567093fa8
This patch reworks type usage in generic code, drivers and ARM platform files
to make it more portable. The major changes done with respect to
type usage are as listed below:
* Use uintptr_t for storing address instead of uint64_t or unsigned long.
* Review usage of unsigned long as it can no longer be assumed to be 64 bit.
* Use u_register_t for register values whose width varies depending on
whether AArch64 or AArch32.
* Use generic C types where-ever possible.
In addition to the above changes, this patch also modifies format specifiers
in print invocations so that they are AArch64/AArch32 agnostic. Only files
related to upcoming feature development have been reworked.
Change-Id: I9f8c78347c5a52ba7027ff389791f1dad63ee5f8
The legacy GIC driver assumes that the SGIs and PPIs are Group0 during
initialization. This is true if the driver is the first one to initialize
the GIC hardware after reset. But in some cases, earlier BL stages could
have already initialized the GIC hardware which means that SGI and PPI
configuration are not the expected reset values causing assertion failure
in `gicd_set_ipriorityr()`. This patch explicitly resets the SGI and PPI
to Group0 prior to their initialization in the driver. The same patch is
not done in the GICv2-only driver because unlike in the legacy driver,
`gicd_set_ipriorityr()` of GICv2 driver doesn't enforce this policy and
the appropriate group is set irrespective of the initial value.
FixesARM-software/tf-issues#396
Change-Id: I521d35caa37470ce542c796c2ba99716e4763105
This patch adds the API `ccn_get_part0_id` to query the PART0 ID from the
PERIPHERAL_ID 0 register in the CCN driver. This ID allows to distinguish
the variant of CCN present on the system and possibly enable dynamic
configuration of the IP based on the variant. Also added an assert in
`ccn_master_to_rn_id_map()` to ensure that the master map bitfield provided
by the platform is within the expected interface id.
Change-Id: I92d2db7bd93a9be8a7fbe72a522cbcba0aba2d0e
Currently the `tzc400_configure_region` and `tzc_dmc500_configure_region`
functions uses uintptr_t as the data type for `region_top` and `region_base`
variables, which will be converted to 32/64 bits for AArch32/AArch64
respectively. But the expectation is to keep these addresses at least 64 bit.
This patch modifies the data types to make it at least 64 bit by using
unsigned long long instead of uintptr_t for the `region_top` and
`region_base` variables. It also modifies the associated macros
`_tzc##fn_name##_write_region_xxx` accordingly.
Change-Id: I4e3c6a8a39ad04205cf0f3bda336c3970b15a28b
The ARM CoreLink DMC-500 Dynamic Memory Controller provides the
programmable address region control of a TrustZone Address Space
Controller. The access permissions can be defined for eight
separate address regions plus a background or default region.
This patch adds a DMC-500 driver to define address regions and
program their access permissions as per ARM 100131_0000_02_en
(r0p0) document.
Change-Id: I9d33120f9480d742bcf7937e4b876f9d40c727e6
TrustZone protection can be programmed by both memory and TrustZone
address space controllers like DMC-500 and TZC-400. These peripherals
share a similar programmer's view.
Furthermore, it is possible to have multiple instances of each type of
peripheral in a system resulting in multiple programmer's views.
For example, on the TZC-400 each of the 4 filter units can be enabled
or disabled for each region. There is a single set of registers to
program the region attributes. On the DMC-500, each filter unit has its
own programmer's view resulting in multiple sets of registers to program
the region attributes. The layout of the registers is almost the same
across all these variations.
Hence the existing driver in `tzc400\tzc400.c` is refactored into the
new driver in `tzc\tzc400.c`. The previous driver file is still maintained
for compatibility and it is now deprecated.
Change-Id: Ieabd0528e244582875bc7e65029a00517671216d
The PL011 initialization function disables the UART, flushes the FIFO
and waits for the current character to be transmitted before applying
the configuration and enabling the UART. This waiting might result in
a deadlock if the FIFO is disabled while another CPU is printing a
message since the flush of FIFO will never finish.
This patch fixes the problem by removing the flush operation and the
loop for last character completion from the initialization function.
The UART is disabled, configured and enabled again.
Change-Id: I1ca0b6bd9f352c12856f10f174a9f6eaca3ab4ea
This patch adds support for the `%p` format specifier in tf_printf()
following the example of the printf implementation of the stdlib used
in the trusted firmware.
FixesARM-software/tf-issues#292
Change-Id: I0b3230c783f735d3e039be25a9405f00023420da
This patch moves the private GIC common accessors from `gic_common.h` to
a new private header file `gic_common_private.h`. This patch also adds
additional comments to GIC register accessors to highlight the fact
that some of them access register values that correspond to multiple
interrupt IDs. The convention used is that the `set`, `get` and `clr`
accessors access and modify the values corresponding to a single interrupt
ID whereas the `read` and `write` GIC register accessors access the raw
GIC registers and it could correspond to multiple interrupt IDs depending
on the register accessed.
Change-Id: I2643ecb2533f01e3d3219fcedfb5f80c120622f9
The code to set the interrupt priority for secure interrupts in the
new GICv2 and GICv3 drivers is incorrect. The setup code to configure
interrupt priorities of secure interrupts, one interrupt at a time, used
gicd_write_ipriorityr()/gicr_write_ipriority() function affecting
4 interrupts at a time. This bug did not manifest itself because all the
secure interrupts were configured to the highest secure priority(0) during
cold boot and the adjacent non secure interrupt priority would be configured
later by the normal world. This patch introduces new accessors,
gicd_set_ipriorityr() and gicr_set_ipriorityr(), for configuring priority
one interrupt at a time and fixes the the setup code to use the new
accessors.
FixesARM-software/tf-issues#344
Change-Id: I470fd74d2b7fce7058b55d83f604be05a27e1341
GICD_IPRIORITYR and GICD_ITARGETSR specifically support byte addressing
so that individual interrupt priorities can be atomically updated by
issuing a single byte write. The previous implementation of
gicd_set_ipriority() and gicd_set_itargetsr() used 32-bit register
accesses, modifying values for 4 interrupts at a time, using a
read-modify-write approach. This potentially may cause concurrent changes
by other CPUs to the adjacent interrupts to be corrupted. This patch fixes
the issue by modifying these accessors to use byte addressing.
FixesARM-software/tf-issues#343
Change-Id: Iec28b5f5074045b00dfb8d5f5339b685f9425915
Currently, `ccn_snoop_dvm_domain_common()` is responsible for providing
a bitmap of HN-F and HN-I nodes in the interconnect. There is a request
node (RN) corresponding to the master interface (e.g. cluster) that needs
to be added or removed from the snoop/DVM domain. This request node is
removed from or added to each HN-F or HN-I node present in the bitmap
depending upon the type of domain.
The above logic is incorrect when participation of a master interface in
the DVM domain has to be managed. The request node should be removed
from or added to the single Miscellaneous Node (MN) in the system
instead of each HN-I node.
This patch fixes this by removing the intermediate
`ccn_snoop_dvm_domain_common()` and instead reads the MN registers to
get the needed node Id bitmap for snoop(HN-F bitmap) and DVM(MN bitmap)
domains.
Additionally, it renames `MN_DDC_SET_OFF` to `MN_DDC_SET_OFFSET` to
be inline with other macros.
Change-Id: Id896046dd0ccc5092419e74f8ac85e31b104f7a4
The PL011 TRM (ARM DDI 0183G) specifies that the UART must be
disabled before any of the control registers are programmed. The
PL011 driver included in TF does not disable the UART, so the
initialization in BL2 and BL31 is violating this requirement
(and potentially in BL1 if the UART is enabled after reset).
This patch modifies the initialization function in the PL011
console driver to disable the UART before programming the
control registers.
Register clobber list and documentation updated.
FixesARM-software/tf-issues#300
Change-Id: I839b2d681d48b03f821ac53663a6a78e8b30a1a1
Jeenu Viswambharan
Soby Mathew
Douglas Raillard
Antonio Nino Diaz
dp-arm
davidcunado-arm
Masahiro Yamada
Yatharth Kochar
danh-arm
Sudeep Holla
Vikram Kanigiri
Juan Castillo
Haojian Zhuang