To support platforms without Trusted DRAM this patch defines
PLAT_ARM_SPMC_BASE and enables platform to use either Trusted DRAM or
DRAM region behind TZC.
Change-Id: Icaa5c7d33334258ff27e8e0bfd0812c304e68ae4
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Increased BL2 maximum size when CoT descriptors are placed
in device tree.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I6466d2841e189e7f15eb4f1a8db070542893cb5b
This patch adds support for Measured Boot functionality
to FVP platform code. It also defines new properties
in 'tpm_event_log' node to store Event Log address and
it size
'tpm_event_log_sm_addr'
'tpm_event_log_addr'
'tpm_event_log_size'
in 'event_log.dtsi' included in 'fvp_tsp_fw_config.dts'
and 'fvp_nt_fw_config.dts'. The node and its properties
are described in binding document
'docs\components\measured_boot\event_log.rst'.
Change-Id: I087e1423afcb269d6cfe79c1af9c348931991292
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
BL2 size gets increased due to the libfdt library update and
that eventually cause no-optimization build failure for BL2 as below:
aarch64-none-elf-ld.bfd: BL2 image has exceeded its limit.
aarch64-none-elf-ld.bfd: region `RAM' overflowed by 4096 bytes
Makefile:1070: recipe for target 'build/fvp/debug/bl2/bl2.elf' failed
make: *** [build/fvp/debug/bl2/bl2.elf] Error 1
Fixed build failure by increasing BL2 image size limit by 4Kb.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I92a57eb4db601561a98e254b64994bb921a88db3
* changes:
doc: Update memory layout for firmware configuration area
plat/arm: Increase size of firmware configuration area
plat/arm: Load and populate fw_config and tb_fw_config
fconf: Handle error from fconf_load_config
plat/arm: Update the fw_config load call and populate it's information
fconf: Allow fconf to load additional firmware configuration
fconf: Clean confused naming between TB_FW and FW_CONFIG
tbbr/dualroot: Add fw_config image in chain of trust
cert_tool: Update cert_tool for fw_config image support
fiptool: Add fw_config in FIP
plat/arm: Rentroduce tb_fw_config device tree
Increased the size of firmware configuration area to accommodate
all configs.
Updated maximum size of following bootloaders due to increase
in firmware configs size and addition of the code in the BL2.
1. Increased maximum size of BL2 for Juno platform in no
optimisation case.
2. Reduced maximum size of BL31 for fvp and Juno platform.
3. Reduced maximum size of BL32 for Juno platform.
Change-Id: Ifba0564df0d1fe86175bed9fae87fdcf013b1831
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Extract Timer clock frequency from the timer node in
HW_CONFIG dtb. The first timer is a per-core architected timer attached
to a GIC to deliver its per-processor interrupts via PPIs.
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I2f4b27c48e4c79208dab9f03c768d9221ba6ca86
This patch introduces the populate function which leverages
a new driver to extract base address and clk frequency properties
of the uart serial node from HW_CONFIG device tree.
This patch also introduces fdt helper API fdtw_translate_address()
which helps in performing address translation.
Change-Id: I053628065ebddbde0c9cb3aa93d838619f502ee3
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Query the GICD and GICR base addresses in runtime using fconf getter
APIs.
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I309fb2874f3329ddeb8677ddb53ed4c02199a1e9
This patch introduces dynamic configuration for SDEI setup and is supported
when the new build flag SDEI_IN_FCONF is enabled. Instead of using C arrays
and processing the configuration at compile time, the config is moved to
dts files. It will be retrieved at runtime during SDEI init, using the fconf
layer.
Change-Id: If5c35a7517ba00a9f258d7f3e7c8c20cee169a31
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Co-authored-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
At the moment the fconf_populate_gicv3_config() implementation is
somewhat incomplete: First it actually fails to store the retrieved
information (the local addr[] array is going nowhere), but also it makes
quite some assumptions about the device tree passed to it: it needs to
use two address-cells and two size-cells, and also requires all five
register regions to be specified, where actually only the first two
are mandatory according to the binding (and needed by our code).
Fix this by introducing a proper generic function to retrieve "reg"
property information from a DT node:
We retrieve the #address-cells and #size-cells properties from the
parent node, then use those to extract the right values from the "reg"
property. The function takes an index to select one region of a reg
property.
This is loosely based on the STM32 implementation using "reg-names",
which we will subsume in a follow-up patch.
Change-Id: Ia59bfdf80aea4e36876c7b6ed4d153e303f482e8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Increased the maximum size of BL2 image in order to
accommodate the BL2 image when TF-A build with no compiler
optimization for ARM platform.
Note: As of now, "no compiler optimization" build works
only when TRUSTED_BOOT_BOARD option is set to 0.
This change is verified using below CI configuration:
1. juno-no-optimize-default:juno-linux.uboot
2. fvp-no-optimize-default,fvp-default:fvp-tftf-fip.tftf-aemv8a-debug
Change-Id: I5932621237f8acd1b510682388f3ba78eae90ea4
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Rather than creating entry in plat_arm_mmap array to map the
entire DRAM region in BL31/SP_MIN, only map a smaller region holding
HW_CONFIG DTB. Consequently, an increase in number of sub-translation
tables(level-2 and level-3) i.e., MAX_XLAT_TABLES is necessary to map
the new region in memory.
In order to accommodate the increased code size in BL31 i.e.,
PROGBITS, the max size of BL31 image is increased by 0x1000(4K).
Change-Id: I540b8ee550588e22a3a9fb218183d2ab8061c851
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Create, register( and implicitly invoke) fconf_populate_topology()
function which extracts the topology related properties from dtb into
the newly created fconf based configuration structure 'soc_topology'.
Appropriate libfdt APIs are added to jmptbl.i file for use with USE_ROMLIB
build feature.
A new property which describes the power domain levels is added to the
HW_CONFIG device tree source files.
This patch also fixes a minor bug in the common device tree file
fvp-base-gicv3-psci-dynamiq-common.dtsi
As this file includes fvp-base-gicv3-psci-common.dtsi, it is necessary
to delete all previous cluster node definitons because DynamIQ based
models have upto 8 CPUs in each cluster. If not deleted, the final dts
would have an inaccurate description of SoC topology, i.e., cluster0
with 8 or more core nodes and cluster1 with 4 core nodes.
Change-Id: I9eb406da3ba4732008a66c01afec7c9fa8ef59bf
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Necessary infrastructure added to integrate fconf framework in BL31 & SP_MIN.
Created few populator() functions which parse HW_CONFIG device tree
and registered them with fconf framework. Many of the changes are
only applicable for fvp platform.
This patch:
1. Adds necessary symbols and sections in BL31, SP_MIN linker script
2. Adds necessary memory map entry for translation in BL31, SP_MIN
3. Creates an abstraction layer for hardware configuration based on
fconf framework
4. Adds necessary changes to build flow (makefiles)
5. Minimal callback to read hw_config dtb for capturing properties
related to GIC(interrupt-controller node)
6. updates the fconf documentation
Change-Id: Ib6292071f674ef093962b9e8ba0d322b7bf919af
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
When TF-A is built with RESET_TO_BL31=1 option, BL31 is the
first image to be run and should have all the memory allocated
to it except for the memory reserved for Shared RAM at the start
of Trusted SRAM.
This patch fixes FVP BL31 load address and its image size for
RESET_TO_BL31=1 option. BL31 startup address should be set to
0x400_1000 and its maximum image size to the size of Trusted SRAM
minus the first 4KB of shared memory.
Loading BL31 at 0x0402_0000 as it is currently stated in
'\docs\plat\arm\fvp\index.rst' causes EL3 exception when the
image size gets increased (i.e. building with LOG_LEVEL=50)
but doesn't exceed 0x3B000 not causing build error.
Change-Id: Ie450baaf247f1577112f8d143b24e76c39d33e91
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Stack usage reaches 90% with some configuration. Bump slightly the stack
size to prevent a stack-overflow.
Change-Id: I44ce8b12906586a42f152b7677785fcdc5e78ae1
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
NOTE for platform integrators:
API `plat_psci_stat_get_residency()` third argument
`last_cpu_idx` is changed from "signed int" to the
"unsigned int" type.
Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.
2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent
Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.
Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c
The Secure Partition Manager (SPM) prototype implementation is
being removed. This is preparatory work for putting in place a
dispatcher component that, in turn, enables partition managers
at S-EL2 / S-EL1.
This patch removes:
- The core service files (std_svc/spm)
- The Resource Descriptor headers (include/services)
- SPRT protocol support and service definitions
- SPCI protocol support and service definitions
Change-Id: Iaade6f6422eaf9a71187b1e2a4dffd7fb8766426
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
There are two different implementations of Secure Partition
management in TF-A. One is based on the "Management Mode" (MM)
design, the other is based on the Secure Partition Client Interface
(SPCI) specification. Currently there is a dependency between their
build flags that shouldn't exist, making further development
harder than it should be. This patch removes that
dependency, making the two flags function independently.
Before: ENABLE_SPM=1 is required for using either implementation.
By default, the SPCI-based implementation is enabled and
this is overridden if SPM_MM=1.
After: ENABLE_SPM=1 enables the SPCI-based implementation.
SPM_MM=1 enables the MM-based implementation.
The two build flags are mutually exclusive.
Note that the name of the ENABLE_SPM flag remains a bit
ambiguous - this will be improved in a subsequent patch. For this
patch the intention was to leave the name as-is so that it is
easier to track the changes that were made.
Change-Id: I8e64ee545d811c7000f27e8dc8ebb977d670608a
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Provide an SMC interface to the 9p filesystem. This permits
accessing firmware drivers through a common interface, using
standardized read/write/control operations.
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I9314662314bb060f6bc02714476574da158b2a7d
Previously the .init section was created even when the reclaim flag was
manually set to 0.
Change-Id: Ia9e7c7997261f54a4eca725d7ea605192f60bcf8
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Zelalem Aweke <zelalem.aweke@arm.com>
ROMLIB extract functions code from BL images to put them inside ROM.
This has for effect to reduce the size of the BL images.
This patch take this size reduction into consideration to optimize the
memory layout of BL2.
A new "PLAT_ARM_BL2_ROMLIB_OPTIMIZATION" macro is defined and used to
reduce "PLAT_ARM_MAX_BL2_SIZE". This allows to remove the gap between
BL1 and BL2 when ROMLIB is used and provides more room for BL31.
The current memory gain is 0x6000 for fvp and 0x8000 for juno.
Change-Id: I71c2c2c63b57bce5b22a125efaefc486ff3e87be
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
NOTE: AARCH32/AARCH64 macros are now deprecated in favor of __aarch64__.
All common C compilers pre-define the same macros to signal which
architecture the code is being compiled for: __arm__ for AArch32 (or
earlier versions) and __aarch64__ for AArch64. There's no need for TF-A
to define its own custom macros for this. In order to unify code with
the export headers (which use __aarch64__ to avoid another dependency),
let's deprecate the AARCH32 and AARCH64 macros and switch the code base
over to the pre-defined standard macro. (Since it is somewhat
unintuitive that __arm__ only means AArch32, let's standardize on only
using __aarch64__.)
Change-Id: Ic77de4b052297d77f38fc95f95f65a8ee70cf200
Signed-off-by: Julius Werner <jwerner@chromium.org>
N1SDP platform supports RDIMMs with ECC capability. To use the ECC
capability, the entire DDR memory space has to be zeroed out before
enabling the ECC bits in DMC620. Zeroing out several gigabytes of
memory from SCP is quite time consuming so functions are added that
zeros out the DDR memory from application processor which is
much faster compared to SCP. BL33 binary cannot be copied to DDR memory
before enabling ECC so this is also done by TF-A from IOFPGA-DDR3
memory to main DDR4 memory after ECC is enabled.
Original PLAT_PHY_ADDR_SPACE_SIZE was limited to 36-bits with which
the entire DDR space cannot be accessed as DRAM2 starts in base
0x8080000000. So these macros are redefined for all ARM platforms.
Change-Id: If09524fb65b421b7a368b1b9fc52c49f2ddb7846
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
The default DRAM2 base address for Arm platforms
is 0x880000000. However, on some platforms the
firmware may want to move the start address to
a different value.
To support this introduce PLAT_ARM_DRAM2_BASE that
defaults to 0x880000000; but can be overridden by
a platform (e.g. in platform_def.h).
Change-Id: I0d81195e06070bc98f376444b48ada2db1666e28
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
When RECLAIM_INIT_CODE is 1, the stack is used to contain the .text.init
section. This is by default enable on FVP. Due to the size increase of
the .text.init section, the stack had to be adjusted contain it.
Change-Id: Ia392341970fb86c0426cf2229b1a7295453e2e32
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
This patch adds support for Versatile express FVP (Fast models).
Versatile express is a family of platforms that are based on ARM v7.
Currently this port has only been tested on Cortex A7, although it
should work with other ARM V7 cores that support LPAE, generic timers,
VFP and hardware divide. Future patches will support other
cores like Cortex A5 that dont support features like LPAE
and hardware divide. This platform is tested on and only expected to
work on single core models.
Change-Id: I10893af65b8bb64da7b3bd851cab8231718e61dd
Signed-off-by: Usama Arif <usama.arif@arm.com>
The variable is renamed to PLAT_ARM_RUN_UART as
the UART is used outside BL31 as well.
Change-Id: I00e3639dfb2001758b7d24548c11236c6335f64a
Signed-off-by: Usama Arif <usama.arif@arm.com>
PLAT_ARM_NS_IMAGE_OFFSET is in fact not an offset relative to some base
address, it is an absolute address. Rename it to avoid any confusion.
Change-Id: I1f7f5e8553cb267786afe7e5f3cd4d665b610d3f
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The PLAT_XLAT_TABLES_DYNAMIC build option, defined in platform_def.h
in Arm platforms, is checked by several headers, affecting their
behaviour. To avoid issues around the include ordering of the headers,
the definition should be moved to the platform's makefile.
Change-Id: I0e12365c8d66309122e8a20790e1641a4f480a10
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Use full include paths like it is done for common includes.
This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.
Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The SPM implementation based on MM is going to be kept for the
foreseeable future.
Change-Id: I11e96778a4f52a1aa803e7e048d9a7cb24a53954
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.
This also prevents problems like cyclic dependencies.
Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Update some asserts that refer to #defines that only occur in
ARM platforms, preventing this code to be used on other platforms.
Instead, use a platform agnostic name, and update all the existing
users.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
SPM needs to map a number of regions on behalf of the secure partition.
Previously, it used to get a list of them from platform code using the
plat_get_secure_partition_mmap() API. Now it gets them from the resource
description structure.
The SPM<->SP shared buffer is mapped dynamically at EL3. This buffer is
used to pass information between SPM and SP, so it must be mapped at EL3
as well in order to be used by SPM.
Dynamic translation tables have been enabled when the Trusted Firmware
is compiled with SPM support.
Change-Id: I64ad335e931661812a0a60558e60372e1e5e6b72
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Load SP and RD from package instead of relying on RD being already
loaded in memory and the SP being loaded as a BL32 image.
Change-Id: I18d4fbf4597656c6a7e878e1d7c01a8a324f3f8a
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Register a priority level, PLAT_SP_PRI, for secure partition with EL3
exception handling framework(ehf) module.
The secure partition manager(SPM) would raise the core's priority to
PLAT_SP_PRI before entering the secure partition, to protect the core
from getting interrupted while in secure partition.
Change-Id: I686897f052a4371e0efa9b929c07d3ad77249e95
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.
The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.
The exceptions are files that are imported from other projects:
- CryptoCell driver
- dt-bindings folders
- zlib headers
Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This file is shared between FVP and all CSS platforms. While it may be
true that some definitions can be common, it doesn't make sense
conceptually. For example, the stack size depends on the platform and so
does the SRAM size.
After removing them, there are not enough common definitions to justify
having this header, so the other definitions have been moved to the
platform_def.h of FVP, board_css_def.h and arm_def.h.
Change-Id: Ifbf4b017227f9dfefa1a430f67d7d6baae6a4ba1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Arunachalam Ganapathy
Manish V Badarkhe
Alexei Fedorov
Sandrine Bailleux
laurenw-arm
Mark Dykes
Madhukar Pappireddy
Balint Dobszay
Andre Przywara
Louis Mayencourt
Deepika Bhavnani
Paul Beesley
Ambroise Vincent
Julius Werner
Manoj Kumar
Sami Mujawar
Usama Arif
Antonio Nino Diaz
Soby Mathew
Ard Biesheuvel
Sughosh Ganu
Sathees Balya