This patch adds the necessary files to support
the SolidRun CN913X CEx7 Evaluation Board.
Because the DRAM connectivity and SerDes settings
is shared with the CN913X DB - reuse relevant
board-specific files.
Change-Id: I75a4554a4373953ca3fdf3b04c4a29c2c4f8ea80
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Map IO WIN to CP1 and CP2 at all stages including the BLE.
Do not map CP1/CP2 if CP_NUM is lower than 2 and 3 accordingly.
This patch allows access to CP1/CP2 internal registers at
BLE stage if CP1/CP2 are connected.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: Icf9ffdf2e9e3cdc2a153429ffd914cc0005f9eca
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/36939
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Yi Guo <yi.guo@cavium.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
The DRAM port code issues a dummy write to SPD page-0 i2c address
in order to select this page for the forthcoming read transaction.
If the write buffer length supplied to i2c_write is not zero, this
call is translated to 2 bus transations:
- set the target offset
- write the data to the target
However no actual data should be transferred to SPD page-0 in order
to select it. Actually, the second transation never receives an ACK
from the target device, which caused the following error report:
ERROR: Status 30 in write transaction
This patch sets the buffer length in page-0 select writes to zero,
leading to bypass the data transfer to the target device.
Issuing the target offset command to SPD page-0 address effectively
selects this page for the read operation.
Change-Id: I4bf8e8c09da115ee875f934bc8fbc9349b995017
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/24387
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Moti Buskila <motib@marvell.com>
The polarity inversion for USB was not tested due to lack of hw design
which requires it. Currently all supported boards doesn't require USB
phy polarity inversion, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards. Enable the option for the ones that need it.
Change-Id: Ia5f2ee313a93962e94963e2dd8a759ef6d9da369
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The cp110 comphy has ability to invert RX and/or TX polarity. Polarity
depends on board design. Currently all supported boards doesn't require
SATA phy polarity invert, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards.
Change-Id: Ifd0bc6aaf8a76a0928132b197422f3193cf020d5
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Marcin Wojtas
Konstantin Porotchkin
Grzegorz Jaszczyk