NOTE for platform integrators:
API `plat_psci_stat_get_residency()` third argument
`last_cpu_idx` is changed from "signed int" to the
"unsigned int" type.
Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.
2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent
Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.
Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c
The SCU connects one to four Cortex-A5/Cortex-A9 processors
to the memory system through the AXI interfaces.
The SCU functions are to:
- maintain data cache coherency between the Cortex-A5/Cortex-A9
processors
- initiate L2 AXI memory accesses
- arbitrate between Cortex-A5/Cortex-A9 processors requesting
L2 accesses
- manage ACP accesses.
Snoop Control Unit will enable to snoop on other CPUs caches.
This is very important when it comes to synchronizing data between
CPUs. As an example, there is a high chance that data might be
cache'd and other CPUs can't see the change. In such cases,
if snoop control unit is enabled, data is synchoronized immediately
between CPUs and the changes are visible to other CPUs.
This driver provides functionality to enable SCU as well as enabling
user to know the following
- number of CPUs present
- is a particular CPU operating in SMP mode or AMP mode
- data cache size of a particular CPU
- does SCU has ACP port
- is L2CPRESENT
Change-Id: I0d977970154fa60df57caf449200d471f02312a0
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Some platforms are extremely memory constrained and must split BL31
between multiple non-contiguous areas in SRAM. Allow the NOBITS
sections (.bss, stacks, page tables, and coherent memory) to be placed
in a separate region of RAM from the loaded firmware image.
Because the NOBITS region may be at a lower address than the rest of
BL31, __RW_{START,END}__ and __BL31_{START,END}__ cannot include this
region, or el3_entrypoint_common would attempt to invalidate the dcache
for the entire address space. New symbols __NOBITS_{START,END}__ are
added when SEPARATE_NOBITS_REGION is enabled, and the dcached for the
NOBITS region is invalidated separately.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Idedfec5e4dbee77e94f2fdd356e6ae6f4dc79d37
Erratum 1688305 is a Cat B erratum present in r0p0, r0p1 versions
of Hercules core. The erratum can be avoided by setting bit 1 of the
implementation defined register CPUACTLR2_EL1 to 1 to prevent store-
release from being dispatched before it is the oldest.
Change-Id: I2ac04f5d9423868b6cdd4ceb3d0ffa46e570efed
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Add additional field definitions for
Cortex_A72 L2 Control registers
Change-Id: I5ef3a6db41cd7c5d9904172720682716276b7889
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
The contents of this header have been merged into the spm_mm_svc.h
header file.
Change-Id: I01530b2e4ec1b4c091ce339758025e2216e740a4
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Before adding any new SPM-related components we should first do
some cleanup around the existing SPM-MM implementation. The aim
is to make sure that any SPM-MM components have names that clearly
indicate that they are MM-related. Otherwise, when adding new SPM
code, it could quickly become confusing as it would be unclear to
which component the code belongs.
The secure_partition.h header is a clear example of this, as the
name is generic so it could easily apply to any SPM-related code,
when it is in fact SPM-MM specific.
This patch renames the file and the two structures defined within
it, and then modifies any references in files that use the header.
Change-Id: I44bd95fab774c358178b3e81262a16da500fda26
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
The Secure Partition Manager (SPM) prototype implementation is
being removed. This is preparatory work for putting in place a
dispatcher component that, in turn, enables partition managers
at S-EL2 / S-EL1.
This patch removes:
- The core service files (std_svc/spm)
- The Resource Descriptor headers (include/services)
- SPRT protocol support and service definitions
- SPCI protocol support and service definitions
Change-Id: Iaade6f6422eaf9a71187b1e2a4dffd7fb8766426
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
There are two different implementations of Secure Partition
management in TF-A. One is based on the "Management Mode" (MM)
design, the other is based on the Secure Partition Client Interface
(SPCI) specification. Currently there is a dependency between their
build flags that shouldn't exist, making further development
harder than it should be. This patch removes that
dependency, making the two flags function independently.
Before: ENABLE_SPM=1 is required for using either implementation.
By default, the SPCI-based implementation is enabled and
this is overridden if SPM_MM=1.
After: ENABLE_SPM=1 enables the SPCI-based implementation.
SPM_MM=1 enables the MM-based implementation.
The two build flags are mutually exclusive.
Note that the name of the ENABLE_SPM flag remains a bit
ambiguous - this will be improved in a subsequent patch. For this
patch the intention was to leave the name as-is so that it is
easier to track the changes that were made.
Change-Id: I8e64ee545d811c7000f27e8dc8ebb977d670608a
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Provide an SMC interface to the 9p filesystem. This permits
accessing firmware drivers through a common interface, using
standardized read/write/control operations.
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I9314662314bb060f6bc02714476574da158b2a7d
Ported the pmf asm macros and the asm code in the bl31 entrypoint
necessary for the instrumentation to AArch32.
Since smc dispatch is handled by the bl32 payload on AArch32, we
provide this service only if AARCH32_SP=sp_min is set.
Signed-off-by: Bence Szépkúti <bence.szepkuti@arm.com>
Change-Id: Id33b7e9762ae86a4f4b40d7f1b37a90e5130c8ac
The 9p interface provides abstraction layers allowing the software
that uses devices to be independent from the hardware.
This patch provides a file system abstraction to link drivers to their
devices and propose a common interface to expose driver operations to
higher layers. This file system can be used to access and configure a
device by doing read/write operations.
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Ia9662393baf489855dc0c8f389fe4a0afbc9c255
SIZE_MAX was mistakenly redefined from UINT32_MAX to UINT64_MAX
on AArch32 when the arch-specific headers were merged.
This value is not currently used by upstream TF-A source code,
so no functionality should be affected.
Change-Id: I2acf7f8736423697c7377e8ed4b08843ced26e66
Signed-off-by: Bence Szépkúti <bence.szepkuti@arm.com>
Previously, the A64/H5 and H6 platforms' PMIC setup code was entirely
independent. However, some H6 boards also need early regulator setup.
Most of the register interface and all of the device tree traversal code
can be reused between the AXP803 and AXP805. The main difference is the
hardware bus interface, so that part is left to the platforms. The
remainder is moved into a driver.
I factored out the bits that were obviously specific to the AXP803;
additional changes for compatibility with other PMICs can be made as
needed.
The only functional change is that rsb_init() now checks the PMIC's chip
ID register against the expected value. This was already being done in
the H6 version of the code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Icdcf9edd6565f78cccc503922405129ac27e08a2
This adds the new regulator list, as well as changes to make the switch
(equivalent to DC1SW on the AXP803) work on both PMICs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I9a1eac8ddfc54b27096c10a8eebdd51aaf9b8311
When a Firmware is complied as Position Independent Executable it needs
to request GDT fixup by passing size of the memory region to
el3_entrypoint_common macro.
The Global descriptor table fixup will be done early on during cold boot
process of primary core.
Currently only BL31 supports PIE, but in future when BL2_AT_EL3 will be
compiled as PIE, it can simply pass fixup size to the common el3
entrypoint macro to fixup GDT.
The reason for this patch was to overcome the bug introduced by SHA
330ead806 which called fixup routine for each core causing
re-initializing of global pointers thus overwriting any changes
done by the previous core.
Change-Id: I55c792cc3ea9e7eef34c2e4653afd04572c4f055
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Add the support needed to enable using CryptoCell integration with
with RSA 3K support.
Signed-off-by: Gilad Ben-Yossef <gilad.benyossef@arm.com>
Change-Id: I95527cb0c41ae012109e8968dd20a4ae9fe67f17
This function scans a string backwards from the end for the first
instance of a character.
Change-Id: I46b21573ed25a0ff222eac340e1e1fb93b040763
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
C99 standard: "What constitutes an access to an object that has
volatile-qualified type is implementation-defined".
GCC is not considering the cast to void of volatile structures as an
access and so is not actually issuing reads.
Clang does read those structures by copying them on the stack, which in
this case creates an overflow because of their large size.
This patch removes the cast to void and instead uses the USED attribute
to tell the compiler to retain the static variables.
Change-Id: I952b5056e3f6e91841e7ef9558434352710ab80d
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Zelalem Aweke <zelalem.aweke@arm.com>
Previously the .init section was created even when the reclaim flag was
manually set to 0.
Change-Id: Ia9e7c7997261f54a4eca725d7ea605192f60bcf8
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Zelalem Aweke <zelalem.aweke@arm.com>
Check that entry point information requesting S-EL2
has AArch64 as an execution state during context setup.
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I447263692fed6e55c1b076913e6eb73b1ea735b7
This patch adds support for enabling S-EL2 if this EL is specified in the entry
point information being used to initialise a secure context. It is the caller's
responsibility to check if S-EL2 is available on the system before requesting
this EL through the entry point information.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Change-Id: I2752964f078ab528b2e80de71c7d2f35e60569e1
Consolidate the definition of size_t to one header per AArch, and
the definition of NULL to one header
Signed-off-by: Bence Szépkúti <bence.szepkuti@arm.com>
Change-Id: Iecfbad2cf360cfb705ce7aaa981700fd16219b82
As supporting architectures aside from AArch32 and AArch64 is not a
concern, keeping identical definitions in two places for a large part
of the libc seems counterproductive
The int128 types were left un-unified as __int128 is not supported by
gcc on AArch32
Signed-off-by: Bence Szépkúti <bence.szepkuti@arm.com>
Change-Id: Idf08e6fab7e4680d9da62d3c57266ea2d80472cf
Conceptually, these are supposed to be the largest integers
representable in C, but GCC and Clang define them as long long for
compatibility.
Signed-off-by: Bence Szépkúti <bence.szepkuti@arm.com>
Change-Id: I7c0117f3be167342814d260a371889120dcf6576
From AArch64 state, arguments are passed in registers W0-W7(X0-X7)
and results are returned in W0-W7(X0-X7) for SMC32(SMC64) calls.
From AArch32 state, arguments are passed in registers R0-R7 and
results are returned in registers R0-R7 for SMC32 calls.
Most of the functions and macros already existed to support using
upto 8 registers for passing/returning parameters/results. Added
few helper macros for SMC calls from AArch32 state.
Link to the specification:
https://developer.arm.com/docs/den0028/c
Change-Id: I87976b42454dc3fc45c8343e9640aa78210e9741
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Add support to configure GIC-600's multichip routing table registers.
Introduce a new gic600 multichip structure in order to support platforms
to pass their GIC-600 multichip information such as routing table owner,
SPI blocks ownership.
This driver is currently experimental and the driver api may change in
the future.
Change-Id: Id409d0bc07843e271ead3fc2f6e3cb38b317878d
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Earlier PIE support was enabled for all arm platforms when
RESET_TO_BL31=1, but later on it was restricted only to FVP with patch
SHA d4580d17 because of n1sdp platform.
Now it has been verified that PIE does work for n1sdp platform also, so
enabling it again for all arm platforms.
Change-Id: I05ad4f1775ef72e7cb578ec9245cde3fbce971a5
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
ARM platform can have a non-contiguous GICR frames. For instance, a
multi socket platform can have two or more GIC Redistributor frames
which are 4TB apart. Hence it is necessary for the `gicv3_rdistif_probe`
function to probe all the GICR frames available in the platform.
Introduce `plat_arm_override_gicr_frames` function which platforms can
use to override the default gicr_frames which holds the GICR base
address of the primary cpu.
Change-Id: I1f537b0d871a679cb256092944737f2e55ab866e
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
The function has to use read_cntpct_el0() to update the counter, and not
read_cntfrq_el0().
Change-Id: I9c676466e784c3122e9ffc2d87e66708797086e7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Deepika Bhavnani
Vishnu Banavath
Alexei Fedorov
Manish Pandey
Samuel Holland
Madhukar Pappireddy
Sheetal Tigadoli
Mark Dykes
Paul Beesley
György Szing
Ambroise Vincent
Soby Mathew
Bence Szépkúti
Olivier Deprez
Sandrine Bailleux
Gilad Ben-Yossef
Artsem Artsemenka
Achin Gupta
Vijayenthiran Subramaniam
Balint Dobszay
Yann Gautier