MHU doorbell driver requires arm platform specific
macro "PLAT_CSS_MHU_BASE".
Rename it to "PLAT_MHUV2_BASE", so that platforms other than arm
can use generic MHU doorbell driver.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This TODO was added five years ago so I assume that there is not
going to be a shutdown API added after all.
Change-Id: If0f4e2066454df773bd9bf41ed65d3a10248a2d3
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
There are some issues with synopsys MMC driver:
- CMD8 should not expect data (for SD)
- ACMD51 should expect data (Send SCR for SD)
- dw_prepare should not dictate size to be MMC_BLOCK_SIZE, block size is
now handled in the dw_prepare function
- after the CMD completes, when doing dw_read, we need to invalidate cache
and wait for the data transfer to complete
- Need to set FIFO threshold, otherwise DMA might never get the interrupt
to read or write
Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>
Some bugs in MMC stack needs to be fixed:
- scr cannot be local as this will cause cache issue when invalidating
after the read DMA transfer is completed
- ACMD41 needs to send voltage information in initialization, otherwise the
command is a query, thus will not initialize the controller
- when checking device state, retry until the retries counter goes to zero
before failing
Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>
This commit improves the SDHost driver for RPi3 as following:
* Unblock MMC_CMD(17). Using MMC_CMD(17) is more efficient on
block reading.
* In some low probability that SEND_OP_COND might results CRC7
error. We can consider that the command runs correctly. We don't
need to retry this command so removing the code for retry.
* Using MMC_BUS_WIDTH_1 as MMC default value to improve the stability.
* Increase the clock to 50Mhz in data mode to speed up the io.
* Change the pull resistors configuration to gain more stability.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
STM32MP1 chip embeds a dual Cortex-A7 and a Cortex-M4.
The support for Cortex-M4 clocks is added when configuring the clock tree.
Some minimal security features to allow communications between A7 and M4
are also added.
Change-Id: I60417e244a476f60a2758f4969700b2684056665
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Remove useless private structure in function prototypes.
Add a reference counter on clocks.
Prepare for future secured/shared/non-secured clocks.
Change-Id: I3dbed81721da5ceff5e10b2c4155b1e340c036ee
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
This change makes the platform to panic in case of peripheral reset
resource malfunction.
Change-Id: I17eb9cb045b78a4e5142a8c33b744e84992d732a
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
Create a new file stm32mp_clkfunc.c to put functions that could be common
between several platforms.
Change-Id: Ica915c796b162b2345056b33328acc05035a242c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Regulator configuration at boot takes more information from DT.
I2C configuration from DT is done in I2C driver.
I2C driver manages more transfer modes.
The min voltage of buck1 should also be increased to 1.2V,
else the platform does not boot.
Heavily modifies stm32_i2c.c since many functions move inside the source
file to remove redundant declarations.
Change-Id: I0bee5d776cf3ff15e687427cd6abc06ab237d025
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
Remove the previously use function: get_timer, and use new functions
timeout_init_us and timeout_elapsed.
Change-Id: I4e95b123648bff7ca91e40462a2a3ae24cfe1697
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
Mainly remove suffix 1 from prefix stm32mp1 in several macros and functions
that can be used in drivers shared by different platforms.
Change-Id: I2295c44f5b1edac7e80a93c0e8dfd671b36e88e7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
This commit adds SDHost driver for RaspberryPi3. SDHost driver uses the
GPIO driver to connect the SDCard and SDHost. By using this driver it is
able to read/write raw blocks on SDCard.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
This commit adds GPIO driver for RaspberryPi3. The GPIO driver for RPi3
also provides the way to do pinmux selections.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Valid addresses for GICR base are always a set calculable distance from
the GICD and is based on the number of cores a given instance of GICv3 IP
can support. The formula for the number of address bits is given by the
ARM GIC-500 TRM section 3.2 as 2^(18+log2(cores)) with the MSB set to
one for GICR instances. Holes in the GIC address space are also
guaranteed to safely return 0 on reads. This allows us to support runtime
detection of the GICR base address by starting from GIC base address plus
BIT(18) and walking until the GICR ID register (IIDR) is detected. We
stop searching after BIT(20) to prevent searching out into space if
something goes wrong. This can be extended out if we ever have a device
with 16 or more cores.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The BSEC (Boot and Security and OTP control) is intended to control an OTP
(one time programmable) fuse box, used for on-chip non-volatile storage
for device configuration and security parameters.
Change-Id: I38c44684c7b9c6a1f24ec0ae3fe99cec481d5a51
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Change fdt_check_status function to fdt_get_status.
Update GPIO defines.
Move some functions in gpio driver, instead of dt helper file.
Add GPIO bank helper functions.
Use only one status field in dt_node_info structure including both status
and secure status.
Change-Id: I34f93408dd4aac16ae722f564bc3f7d6ae978cf4
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Reword some traces.
Use uintptr_t where required.
Reduce scope of variables.
Improve io_stm32image algo.
Complete some IP registers definitions.
Add failure on supported DDR (stm32mp1_ddr_init()).
Fix cache flush on cache disable (stm32mp1_ddr_setup).
Change-Id: Ie02fa71e02b9d69abc807fd5b7df233e5be6668c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Change-Id: I4a1b281925e0a3a1e2a34b3e363537e4a7f13823
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
The drivers are also updated to reflect the changes.
Set RCC as non-secure.
Change-Id: I568fa1f418355830ad1d4d1cdcdb910fb362231b
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This is the correct name of the IP.
Rename stm32mp1_pmic files to stm32mp_pmic.
Change-Id: I238a7d1f9a1d099daf7788dc9ebbd3146ba2f15f
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Instead, only platform_def.h is included.
The required files to be included are added in stm32mp1_def.h.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The GIC lowest priority values for each world depends on the number of
priority values implemented in hardware. These constants currently
defined in gic_common.h only meant to enumerate lowest possible
architectural values. Since these values are not used in generic code or
upstream platforms, and that general use of these constants can be
wrong, remove these. Platforms should either define and use these as
appropriate, or determine correct values at run time.
Change-Id: I3805cea8ceb8a592b9eff681ea1b63b7496cec5f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
console_unregister() has always returned a pointer to the console that
was removed on success, not just an integer. Fix the C prototype to
match the assembly implementation.
Change-Id: Iafc43de0767a5c87c9ae5c3aba53761dd28d51e6
Signed-off-by: Julius Werner <jwerner@chromium.org>
- Update CPU frequency on AP807 to 2GHz for SAR 0x0.
- Increase AVS to 0.88V for 2GHz clock
Change-Id: Ic945b682ab2f8543e34294bfc56c3eae2c5e0c8e
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
ARM CoreLink DMC-620 Dynamic Memory Controller includes a TZC controller
to setup secure or non-secure regions of DRAM memory. The TZC controller
allows to setup upto eight such regions of memory in DRAM. This driver
provides helper functions to setup the TZC controller within DMC-620.
Change-Id: Iee7692417c2080052bdb7b1c2873a024bc5d1d10
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Migrate Marvell platforms from legacy console API to
multi-console API.
Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>