Reference code:
==============
rar_gen3: IPL and Secure Monitor Rev1.0.22
https://github.com/renesas-rcar/arm-trusted-firmware [rcar_gen3]
Author: Takuya Sakata <takuya.sakata.wz@bp.renesas.com>
Date: Thu Aug 30 21:26:41 2018 +0900
Update IPL and Secure Monitor Rev1.0.22
General Information:
===================
This port has been tested on the Salvator-X Soc_id r8a7795 revision
ES1.1 (uses an SPD).
Build Tested:
-------------
ATFW_OPT="LSI=H3 RCAR_DRAM_SPLIT=1 RCAR_LOSSY_ENABLE=1"
MBEDTLS_DIR=$mbedtls
$ make clean bl2 bl31 rcar PLAT=rcar ${ATFW_OPT} SPD=opteed
Other dependencies:
------------------
* mbed_tls:
git@github.com:ARMmbed/mbedtls.git [devel]
Merge: 68dbc94 f34a4c1
Author: Simon Butcher <simon.butcher@arm.com>
Date: Thu Aug 30 00:57:28 2018 +0100
* optee_os:
https://github.com/BayLibre/optee_os
Until it gets merged into OP-TEE, the port requires Renesas' Trusted
Environment with a modification to support power management.
Author: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Date: Thu Aug 30 16:49:49 2018 +0200
plat-rcar: cpu-suspend: handle the power level
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
* u-boot:
The port has beent tested using mainline uboot.
Author: Fabio Estevam <festevam@gmail.com>
Date: Tue Sep 4 10:23:12 2018 -0300
*linux:
The port has beent tested using mainline kernel.
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Sep 16 11:52:37 2018 -0700
Linux 4.19-rc4
Overview
---------
BOOTROM starts the cpu at EL3; In this port BL2 will therefore be entered
at this exception level (the Renesas' ATF reference tree [1] resets into
EL1 before entering BL2 - see its bl2.ld.S)
BL2 initializes DDR (and i2c to talk to the PMIC on some platforms)
before determining the boot reason (cold or warm).
During suspend all CPUs are switched off and the DDR is put in
backup mode (some kind of self-refresh mode). This means that BL2 is
always entered in a cold boot scenario.
Once BL2 boots, it determines the boot reason, writes it to shared
memory (BOOT_KIND_BASE) together with the BL31 parameters
(PARAMS_BASE) and jumps to BL31.
To all effects, BL31 is as if it is being entered in reset mode since
it still needs to initialize the rest of the cores; this is the reason
behind using direct shared memory access to BOOT_KIND_BASE and
PARAMS_BASE instead of using registers to get to those locations (see
el3_common_macros.S and bl31_entrypoint.S for the RESET_TO_BL31 use
case).
Depending on the boot reason BL31 initializes the rest of the cores:
in case of suspend, it uses a MBOX memory region to recover the
program counters.
[1] https://github.com/renesas-rcar/arm-trusted-firmware
Tests
-----
* cpuidle
-------
enable kernel's cpuidle arm_idle driver and boot
* system suspend
--------------
$ cat suspend.sh
#!/bin/bash
i2cset -f -y 7 0x30 0x20 0x0F
read -p "Switch off SW23 and press return " foo
echo mem > /sys/power/state
* cpu hotplug:
------------
$ cat offline.sh
#!/bin/bash
nbr=$1
echo 0 > /sys/devices/system/cpu/cpu$nbr/online
printf "ONLINE: " && cat /sys/devices/system/cpu/online
printf "OFFLINE: " && cat /sys/devices/system/cpu/offline
$ cat online.sh
#!/bin/bash
nbr=$1
echo 1 > /sys/devices/system/cpu/cpu$nbr/online
printf "ONLINE: " && cat /sys/devices/system/cpu/online
printf "OFFLINE: " && cat /sys/devices/system/cpu/offline
Signed-off-by: ldts <jramirez@baylibre.com>
Whereas the GPT table is read with io_block, the binaries to be loaded
(e.g. BL33) cannot use it, as it is not suitable to read them block by
block, or the boot time would be very bad.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This IO is required to read binaries with STM32 header.
This header is added with the stm32image tool.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This driver is for the STMicroelectronics sdmmc2 IP
which is in STM32MP1 SoC.
It uses the MMC framework, and can address either eMMC or SD-card.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The comments with the prototypes of the register functions of the
console drivers are incorrect. The arguments are wrong. This patch fixes
them.
Change-Id: I38c4b481ee69e840780111c42f03c0752eb6315c
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
commit 97d5db8c5c reverts an update to the
MMC layer that accompanied the original submission of this MMC driver this
is the right-thing-to-do in terms of the MMC spec.
Unfortunately the reversion also breaks this driver. The issue is the i.MX
controller doesn't want MMC_RSP_48 set for MMC_RESPONSE_R2.
The appropriate place to place that constraint is obviously in
drivers/imx/usdhc/imx_usdhc.c not in the shared MMC codebase. This patch
restores the logic the i.MX controller requires without breaking it for
everyone else.
Fixes: 97d5db8c5c
Fixes: 2a82a9c95f
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Jun Nie <jun.nie@linaro.org>
This way it can be reused by other platforms if needed.
Note that this driver is designed to work with the Versatile Express NOR
flash of Juno and FVP. In said platforms, the memory is organized as an
interleaved memory of two chips with a 16 bit word.
Any platform that wishes to reuse it with a different configuration will
need to modify the driver so that it is more generic.
Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Mark the GICv3, CCI and CCN code only used in Bl31 initialization
with __init to be reclaimed once no longer needed.
Change-Id: I3d77f36758450d9d1d87ecc60bc1c63fe4082667
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
Respect official response type and update response to follow
official specification.
All the MMC_RESPONSE_R(_x) are replaced with each corresponding define.
Partly revert 2a82a9c95f for dw_mmc.c:
Responses R1, R1B and R5 have CRC.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
It is still a placeholder, but now it is registered correctly by the
macro finish_console_register.
Change-Id: Ic78c966d9be606cbc1a53cec43ead23b32963afe
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The Poplar is broken on eMMC initialization because of commit
2a82a9c95f ("drivers: emmc: dw_mmc: Add response flag into response ID
definition"). It changes the driver behavior on response type handling
in dw_send_cmd(), because MMC_RESPONSE_R(2) and MMC_RESPONSE_R2 are
different things. MMC core is still sending the former while we already
changed to check the latter in dw_mmc driver.
This patch fixes R2 response type in MMC core code. It's the same
thing as what commit 94522ff7f6 ("drivers: mmc: Fix R3 response type
definition") does for R3 response.
With this fix, Poplar is back to work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Allow AArch32 to use the multi console driver by adding the
required functions
Change-Id: I9e69f18965f320074cf75442d6b0de891aef7936
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
The old driver is now in deprecated_console.S, in a similar way to the
AArch64 driver.
Change-Id: Ib57209c322576c451d466d7406a94adbf01ab8fd
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner 64-bit SoCs all use the Mentor Graphics MI2CV I2C controller
core, with inverted clear quirk.
Add a glue driver for this.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The I2C controller on Allwinner SoCs after A31 has a inverted interrupt
clear flag, which needs to be written 1 (rather than 0 on Marvell SoCs
and old Allwinner SoCs) to clear.
Add such a quirk to mi2cv driver common code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which
is also used by Allwinner.
As Mentor Graphics allows a lot of customization, the MI2CV in the two
SoC families are not compatible, and driver modifications are needed.
Extract the common code to a MI2CV driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The I2C controller found in Marvell A8K SoCs (and some older SoCs) mux
status and baudrate registers into the same address, however, it's a
vendor customization, and the original IP core by Mentor Graphics uses
two different addresses for the two registers.
Use anonymous union in the driver, in order to ease code sharing for
other SoC vendors that use this IP core (Allwinner SoCs that are newly
introduced to mainline ATF use this core).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Soby Mathew
Jorge Ramirez-Ortiz
Yann Gautier
Dimitris Papastamos
Antonio Nino Diaz
Bryan O'Donoghue
Daniel Boulby
Shawn Guo
Sathees Balya
Andre Przywara
Icenowy Zheng