diphda platform is now being renamed to corstone1000.
These changes are to replace all the instances and traces
of diphda corstone1000.
Change-Id: I330f3a112d232b99b4721b6bf0236253b068dbba
Signed-off-by: Arpita S.K <Arpita.S.K@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
This commit enables trusted-firmware-a with Trusted Board Boot support
for the Diphda 64-bit platform.
Diphda uses a FIP image located in the flash. The FIP contains the
following components:
- BL2
- BL31
- BL32
- BL32 SPMC manifest
- BL33
- The TBB certificates
The board boot relies on CoT (chain of trust). The trusted-firmware-a
BL2 is extracted from the FIP and verified by the Secure Enclave
processor. BL2 verification relies on the signature area at the
beginning of the BL2 image. This area is needed by the SecureEnclave
bootloader.
Then, the application processor is released from reset and starts by
executing BL2.
BL2 performs the actions described in the trusted-firmware-a TBB design
document.
Signed-off-by: Rui Miguel Silva <rui.silva@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Change-Id: Iddb1cb9c2a0324a9635e23821c210ac81dfc305d
Remove an incorrect tabulation in front of an $(error) function call
outside of a recipe, which caused the following text to be displayed:
plat/arm/board/common/board_common.mk:36: *** recipe commences before first target. Stop.
instead of:
plat/arm/board/common/board_common.mk:36: *** "Unsupported ARM_ROTPK_LOCATION value". Stop.
Change-Id: I8592948e7de8ab0c4abbc56eb65a53eb1875a83c
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Only non-file targets should be set a .PHONY. Otherwise if file target is
set as .PHONY then targets which depends on those file .PHONY targets would
be always rebuilt even when their prerequisites are not changed.
File target which needs to be always rebuilt can be specified in Make
system via having a prerequisite on some .PHONY target, instead of marking
whole target as .PHONY. In Makefile projects it is common to create empty
.PHONY target named FORCE for this purpose.
This patch changes all file targets which are set as .PHONY to depends on
new .PHONY target FORCE, to ensure that these file targets are always
rebuilt (as before). Basically they are those targets which calls external
make subprocess.
After FORCE target is specified in main Makefile, remove it from other
Makefile files to prevent duplicate definitions.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Iee3b4e0de93879b95eb29a1745a041538412e69e
Only define arm_get_rotpk_info_regs if ROTPK is in registers,
i.e. (ARM_ROTPK_LOCATION_ID == ARM_ROTPK_REGS_ID). This will
allow platform build without definition of TZ_PUB_KEY_HASH_BASE
if dedicated registers for ROTPK are not available on the platform.
Change-Id: I74ee2d5007f5d876a031a1efca20ebee2dede0c7
Signed-off-by: Usama Arif <usama.arif@arm.com>
Using the Fconf, register base address of the various nv-counters
(currently, trusted, non-trusted nv-counters) are moved to the
device tree and retrieved during run-time. This feature is
enabled using the build option COT_DESC_IN_DTB.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I236f532e63cea63b179f60892cb406fc05cd5830
The dualroot chain of trust involves 2 root-of-trust public keys:
- The classic ROTPK.
- The platform ROTPK (a.k.a. PROTPK).
Use the cookie argument as a key ID for plat_get_rotpk_info() to return the
appropriate one. This only applies if we are using the dualroot CoT ; if using
the TBBR one, the behaviour is unchanged.
Change-Id: I400707a87ec01afd5922b68db31d652d787f79bd
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The cookie will be leveraged in the next commit.
Change-Id: Ie8bad275d856d84c27466461cf815529dd860446
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
- Use the development PROTPK if using the dualroot CoT.
Note that unlike the ROTPK, the PROTPK key hash file is not generated
from the key file, instead it has to be provided. This might be
enhanced in the future.
- Define a CoT build flag for the platform code to provide different
implementations where needed.
Change-Id: Iaaf25183b94e77a99a5d8d875831d90c102a97ea
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
When using the new dualroot chain of trust, a new root of trust key is
needed to authenticate the images belonging to the platform owner.
Provide a development one to deploy this on Arm platforms.
Change-Id: I481145e09aa564822d474cb47d38ec211dd24efd
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Forced hash generation used to always generate hash via RSA encryption.
This patch changes encryption based on ARM_ROTPK_LOCATION.
Also removes setting KEY_ALG based on ARM_ROTPL_LOCATION - there is no
relation between these two.
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: Id727d2ed06176a243719fd0adfa0cae26c325005
Enables usage of ARM_ROTPK_LOCATION=regs for FVP board.
Removes hard-coded developer keys. Instead, setting
ARM_ROTPK_LOCATION=devel_* takes keys from default directory.
In case of ROT_KEY specified - generates a new hash and replaces the
original.
Note: Juno board was tested by original feature author and was not tested
for this patch since we don't have access to the private key. Juno
implementation was moved to board-specific file without changing
functionality. It is not known whether byte-swapping is still needed
for this platform.
Change-Id: I0fdbaca0415cdcd78f3a388551c2e478c01ed986
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Code using Cryptocell specific APIs was used as part of the
arm common board ROT support, instead of being abstracted
in Cryptocell specific driver code, creating two problems:
- Any none arm board that uses Cryptocell wuld need to
copy and paste the same code.
- Inability to cleanly support multiple versions of Cryptocell
API and products.
Move over Cryptocell specific API calls into the Cryptocell
driver, creating abstraction API where needed.
Signed-off-by: Gilad Ben-Yossef <gilad.benyossef@arm.com>
Change-Id: I9e03ddce90fcc47cfdc747098bece86dbd11c58e
Use full include paths like it is done for common includes.
This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.
Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.
This also prevents problems like cyclic dependencies.
Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This file is only used by Juno as all other CSS platforms have their own
private memory maps.
Change-Id: I1c9f27aac7b1d8bff4d92674e8bde5505b93c8c4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This way it can be reused by other platforms if needed.
Note that this driver is designed to work with the Versatile Express NOR
flash of Juno and FVP. In said platforms, the memory is organized as an
interleaved memory of two chips with a 16 bit word.
Any platform that wishes to reuse it with a different configuration will
need to modify the driver so that it is more generic.
Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This option makes it hard to optimize the memory definitions of all Arm
platforms because any change in the common defines must work in all of
them. The best thing to do is to remove it and move the definition to
each platform's header.
FVP, SGI and SGM were using the definitions in board_arm_def.h. The
definitions have been copied to each platform's platform_def.h. Juno
was already using the ones in platform_def.h, so there have been no
changes.
Change-Id: I9aecd11bbc72a3d0d7aad1ef9934d8df21dcfaf2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
All the arm platforms were including the files related to
mem-protect. This configuration generates some problems
with new platforms that don't support such functionality,
and for that reason this patch moves these files to the
platform specific makefiles.
Change-Id: I6923e5224668b76667795d8e11723cede7979b1e
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Change arm_setup_page_tables() to take a variable number of memory
regions. Remove coherent memory region from BL1, BL2 and BL2U as
their coherent memory region doesn't contain anything and
therefore has a size of 0. Add check to ensure this
doesn't change without us knowing.
Change-Id: I790054e3b20b056dda1043a4a67bd7ac2d6a3bc0
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.
The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.
Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.
In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.
Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.
Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
On ARM platforms, the maximum size of the address space is limited
to 32-bits as defined in arm_def.h. In order to access DRAM2, which
is defined beyond the 32-bit address space, the maximum address space
is increased to 36-bits in AArch64. It is possible to increase the
virtual space for AArch32, but it is more difficult and not supported
for now.
NOTE - the actual maximum memory address space is platform dependent
and is checked at run-time by querying the PARange field in the
ID_AA64MMFR0_EL1 register.
Change-Id: I6cb05c78a63b1fed96db9a9773faca04a5b93d67
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
mem_protect needs some kind of non-volatile memory because it has
to remember its state across reset and power down events.
The most suitable electronic part for this feature is a NVRAM
which should be only accesible from the secure world. Juno and
FVP lack such hardware and for this reason the MEM_PROTECT
functionality is implemented with Flash EEPROM memory on both
boards, even though this memory is accesible from the non-secure
world. This is done only to show a full implementation of
these PSCI features, but an actual system shouldn't use a
non-secure NVRAM to implement it.
The EL3 runtime software will write the mem_protect flag and BL2
will read and clear the memory ranges if enabled. It is done in
BL2 because it reduces the time that TF needs access to the full
non-secure memory.
The memory layout of both boards is defined using macros which
take different values in Juno and FVP platforms. Generic platform
helpers are added that use the platform specific macros to generate
a mem_region_t that is valid for the platform.
Change-Id: I2c6818ac091a2966fa07a52c5ddf8f6fde4941e9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This patch does the required changes to enable CSS platforms
to build and use the SDS framework. Since SDS is always coupled with
SCMI protocol, the preexisting SCMI build flag is now renamed to
`CSS_USE_SCMI_SDS_DRIVER` which will enable both SCMI and SDS on
CSS platforms. Also some of the workarounds applied for SCMI are
now removed with SDS in place.
Change-Id: I94e8b93f05e3fe95e475c5501c25bec052588a9c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The commit 3eb2d67 optimizes the memory map for BL2 when TSP
is not present. But this also broke OP-TEE as it was reusing
the TSP mapping. This patch fixes this problem by adding a
separate mapping for OP-TEE in the BL2 memory map table.
Change-Id: I130a2ea552b7b62d8478081feb1f4ddf5292a118
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch ensures that the ARM_MAP_TSP_SEC_MEM memory region is mapped
in BL2 only if the TSPD has been included in the build. This saves one
entry in the plat_arm_mmap[] array and avoids to map extra memory when
it's not needed.
Change-Id: I6ae60822ff8f0de198145925b0b0d45355179a94
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The nor_XXXXX functions may fail due to different reasons, and it
is convenient to do a full check to detect any failure. It is also
a good idea to have a specific function to do a full status check,
because new checks can be added to this function and they will be
incorporated automatically to any function calling it.
Change-Id: I54fed913e37ef574c1608e94139a519426348d12
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
NOR memory only supports setting bits to 1. To clear a bit, set to zero,
the NOR memory needs to be erased.
Change-Id: Ia82eb15a5af9a6d4fc7e5ea2b58e6db87226b351
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
The status register bits remain until explicitly cleared, which means
that a command can be incorrectly considered to have generated an error -
for example, after reset the status register contents may be unknown or
if a previous command had failed.
This patch clears the status register before beginning any command to
be sure that the status register only represents information about the
current operation.
Change-Id: I9e98110ee24179937215461c00b6543a3467b350
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
lock/unlock operation must wait until WSM bit
is set. Since we do not allow to loop forever then these functions
must return an error if WSM bit isn't enabled after a number of tries.
Change-Id: I21c9e292b514b28786ff4a225128bcd8c1bfa999
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Trusted OS may have extra images to be loaded. Load them one by one
and do the parsing. In this patch, ARM TF need to load up to 3 images
for optee os: header, pager and paged images. Header image is the info
about optee os and images. Pager image include pager code and data.
Paged image include the paging parts using virtual memory.
Change-Id: Ia3bcfa6d8a3ed7850deb5729654daca7b00be394
Signed-off-by: Summer Qin <summer.qin@arm.com>
The DEVICE2 memory range is needed to access the Root of Trust Public
Key registers. This is not needed when Trusted Board Boot is disabled
so it's safer to not map it in this case. This also saves one level-2
page table in each of BL1 and BL2 images.
Also add some comments.
Change-Id: I67456b44f3fd5e145f6510a8499b7fdf720a7273
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
This patch implements the platform APIs plat_get_rotpk_info,
plat_get_nv_ctr, plat_set_nv_ctr to invoke CryptoCell SBROM
APIs when ARM_CRYPTOCELL_INT is set.
Change-Id: I693556b3c7f42eceddd527abbe6111e499f55c45
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds the memory map region for the SCMI payload memory
and maps the Juno core indices to SCMI power domains via the
`plat_css_core_pos_to_scmi_dmn_id_map` array.
Change-Id: I0d2bb2a719ff5b6a9d8e22e91e1625ab14453665
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This function was removed long ago. Remove remaining
pragma reference.
Change-Id: I66c556863d47dc17d2ffdc6c23aa524df6aade80
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
The header tbbr_oid.h contains OIDs obtained by ARM Ltd.
so there is no good reason to use platform_oid.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.
NOTE: Files that have been imported by FreeBSD have not been modified.
[0]: https://spdx.org/
Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
This patch adds support for SP_MIN on JUNO platform.
The changes include addition of AArch32 assembly files,
JUNO specific SP_MIN make file and miscellaneous changes
in ARM platform files to enable support for SP_MIN.
Change-Id: Id1303f422fc9b98b9362c757b1a4225a16fffc0b
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
One nasty part of ATF is some of boolean macros are always defined
as 1 or 0, and the rest of them are only defined under certain
conditions.
For the former group, "#if FOO" or "#if !FOO" must be used because
"#ifdef FOO" is always true. (Options passed by $(call add_define,)
are the cases.)
For the latter, "#ifdef FOO" or "#ifndef FOO" should be used because
checking the value of an undefined macro is strange.
Here, IMAGE_BL* is handled by make_helpers/build_macro.mk like
follows:
$(eval IMAGE := IMAGE_BL$(call uppercase,$(3)))
$(OBJ): $(2)
@echo " CC $$<"
$$(Q)$$(CC) $$(TF_CFLAGS) $$(CFLAGS) -D$(IMAGE) -c $$< -o $$@
This means, IMAGE_BL* is defined when building the corresponding
image, but *undefined* for the other images.
So, IMAGE_BL* belongs to the latter group where we should use #ifdef
or #ifndef.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds common changes to support AArch32 state in
BL1 and BL2. Following are the changes:
* Added functions for disabling MMU from Secure state.
* Added AArch32 specific SMC function.
* Added semihosting support.
* Added reporting of unhandled exceptions.
* Added uniprocessor stack support.
* Added `el3_entrypoint_common` macro that can be
shared by BL1 and BL32 (SP_MIN) BL stages. The
`el3_entrypoint_common` is similar to the AArch64
counterpart with the main difference in the assembly
instructions and the registers that are relevant to
AArch32 execution state.
* Enabled `LOAD_IMAGE_V2` flag in Makefile for
`ARCH=aarch32` and added check to make sure that
platform has not overridden to disable it.
Change-Id: I33c6d8dfefb2e5d142fdfd06a0f4a7332962e1a3
This patch adds AArch32 support for FVP and implements common platform APIs
like `plat_get_my_stack`, `plat_set_my_stack`, `plat_my_core_cos` for AArch32.
Only Multi Processor(MP) implementations of these functions are considered in
this patch. The ARM Standard platform layer helpers are implemented for
AArch32 and the common makefiles are modified to cater for both AArch64 and
AArch32 builds. Compatibility with the deprecated platform API is not
supported for AArch32.
Change-Id: Iad228400613eec91abf731b49e21a15bcf2833ea
This patch migrates the upstream platform makefiles to include the
console drivers from the new location in ARM Trusted Firmware code
base.
Change-Id: I866d6c4951e475de1f836ce8a8c1d5e6da9577e3
Compile option `ARM_BOARD_OPTIMISE_MMAP` has been renamed to
`ARM_BOARD_OPTIMISE_MEM` because it now applies not only to defines
related to the translation tables but to the image size as well.
The defines `PLAT_ARM_MAX_BL1_RW_SIZE`, `PLAT_ARM_MAX_BL2_SIZE` and
`PLAT_ARM_MAX_BL31_SIZE` have been moved to the file board_arm_def.h.
This way, ARM platforms no longer have to set their own values if
`ARM_BOARD_OPTIMISE_MEM=0` and they can specify optimized values
otherwise. The common sizes have been set to the highest values used
for any of the current build configurations.
This is needed because in some build configurations some images are
running out of space. This way there is a common set of values known
to work for all of them and it can be optimized for each particular
platform if needed.
The space reserved for BL2 when `TRUSTED_BOARD_BOOT=0` has been
increased. This is needed because when memory optimisations are
disabled the values for Juno of `PLAT_ARM_MMAP_ENTRIES` and
`MAX_XLAT_TABLES` are higher. If in this situation the code is
compiled in debug mode and with "-O0", the code won't fit.
Change-Id: I70a3d8d3a0b0cad1d6b602c01a7ea334776e718e
This patch introduces the arm_setup_page_tables() function to
set up page tables on ARM platforms. It replaces the
arm_configure_mmu_elx() functions and does the same thing except
that it doesn't enable the MMU at the end. The idea is to reduce
the amount of per-EL code that is generated by the C preprocessor
by splitting the memory regions definitions and page tables creation
(which is generic) from the MMU enablement (which is the only per-EL
configuration).
As a consequence, the call to the enable_mmu_elx() function has been
moved up into the plat_arch_setup() hook. Any other ARM standard
platforms that use the functions `arm_configure_mmu_elx()` must be
updated.
Change-Id: I6f12a20ce4e5187b3849a8574aac841a136de83d
Vishnu Banavath
Abdellatif El Khlifi
Sandrine Bailleux
Pali Rohár
Usama Arif
Manish V Badarkhe
Max Shvetsov
Gilad Ben-Yossef
Antonio Nino Diaz
Soby Mathew
Roberto Vargas
Daniel Boulby
davidcunado-arm
Qixiang Xu
Summer Qin
dp-arm
Masahiro Yamada
Yatharth Kochar