The value of BL31_BASE currently depends on the size of BL31. This
causes problems in the RESET_TO_BL31 case because the value of
BL31_BASE is used in the model launch parameters, which often changes.
Therefore, this patch fixes BL31_BASE to the middle of Trusted SRAM,
to avoid further model parameter changes in future.
Change-Id: I6d7fa4fe293717d84768974679539c0e0cb6d935
Signed-off-by: David Cunado <david.cunado@arm.com>
This patch gives users control over logging messages printed from the C
code using the LOG macros defined in debug.h Users now have the ability
to reduce the log_level at run time using the tf_log_set_max_level()
function. The default prefix string can be defined by platform by
overriding the `plat_log_get_prefix()` platform API which is also
introduced in this patch.
The new log framework results in saving of some RO data. For example,
when BL1 is built for FVP with LOG_LEVEL=LOG_LEVEL_VERBOSE, resulted
in saving 384 bytes of RO data and increase of 8 bytes of RW data. The
framework also adds about 108 bytes of code to the release build of FVP.
FixesARM-software/tf-issues#462
Change-Id: I476013d9c3deedfdd4c8b0b0f125665ba6250554
Co-authored-by: Eleanor Bonnici <Eleanor.bonnici@arm.com>
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch does the required changes to enable CSS platforms
to build and use the SDS framework. Since SDS is always coupled with
SCMI protocol, the preexisting SCMI build flag is now renamed to
`CSS_USE_SCMI_SDS_DRIVER` which will enable both SCMI and SDS on
CSS platforms. Also some of the workarounds applied for SCMI are
now removed with SDS in place.
Change-Id: I94e8b93f05e3fe95e475c5501c25bec052588a9c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch fixes the inconsistency with regards as to how
BL2_BASE/BL2U_BASE and BL2_LIMIT/BL2U_LIMIT macros are defined
when building Juno to run in AArch32 mode at EL3. In this case,
BL32 is compiled for AArch32 whereas BL1 and BL2 are compiled
for AArch64. This resulted in BL32 conditionally compiling a
different definition of the above mentioned macros from BL1/BL2.
This is fixed by taking into consideration the
JUNO_AARCH32_EL3_RUNTIME build flag as well in the conditional
compilation check.
Change-Id: I27ac68aa4df0502089c1739c05366a9c509eb5be
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The commit 3eb2d67 optimizes the memory map for BL2 when TSP
is not present. But this also broke OP-TEE as it was reusing
the TSP mapping. This patch fixes this problem by adding a
separate mapping for OP-TEE in the BL2 memory map table.
Change-Id: I130a2ea552b7b62d8478081feb1f4ddf5292a118
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch ensures that the ARM_MAP_TSP_SEC_MEM memory region is mapped
in BL2 only if the TSPD has been included in the build. This saves one
entry in the plat_arm_mmap[] array and avoids to map extra memory when
it's not needed.
Change-Id: I6ae60822ff8f0de198145925b0b0d45355179a94
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The current definition of ARM_INSTANTIATE_LOCK macro includes a
semicolon, which means it's omitted where it's used. This is anomalous
for a C statement in global scope.
Fix this by removing semicolon from the definition; and where it's a
NOP, declare a file-scoped variable explicitly tagged as unused to avoid
compiler warning.
No functional changes.
Change-Id: I2c1d92ece4777e272a025011e03b8003f3543335
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Changes ARM_OPTEE_PAGEABLE_LOAD_BASE to end of ARM_AP_TZC_DRAM1.
ARM_OPTEE_PAGEABLE_LOAD_SIZE is also increased to 4MB to optimize
translation table usage.
This change makes loading of paged part easier inside OP-TEE OS as the
previous location of ARM_OPTEE_PAGEABLE_LOAD_BASE normally isn't mapped
if paging is enabled.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
NOR memory only supports setting bits to 1. To clear a bit, set to zero,
the NOR memory needs to be erased.
Change-Id: Ia82eb15a5af9a6d4fc7e5ea2b58e6db87226b351
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
lock/unlock operation must wait until WSM bit
is set. Since we do not allow to loop forever then these functions
must return an error if WSM bit isn't enabled after a number of tries.
Change-Id: I21c9e292b514b28786ff4a225128bcd8c1bfa999
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Trusted OS may have extra images to be loaded. Load them one by one
and do the parsing. In this patch, ARM TF need to load up to 3 images
for optee os: header, pager and paged images. Header image is the info
about optee os and images. Pager image include pager code and data.
Paged image include the paging parts using virtual memory.
Change-Id: Ia3bcfa6d8a3ed7850deb5729654daca7b00be394
Signed-off-by: Summer Qin <summer.qin@arm.com>
Revision C of the Base FVP has the same memory map as earlier revisions,
but has the following differences:
- Implements CCI550 instead of CCI400,
- Has a single instantiation of SMMUv3,
- CPU MPIDs are shifted left by one level, and has MT bit set in them.
The correct interconnect to program is chosen at run time based on the
FVP revision. Therefore, this patch implements FVP functions for
interconnect programming, rather than depending on ARM generic ones. The
macros used have been renamed to reflect this change.
Additionally, this patch initializes SMMUv3 as part of FVP early
platform setup.
New ARM config flags are introduced for feature queries at run time.
Change-Id: Ic7b7f080953a51fceaf62ce7daa6de0573801f09
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
On ARM CSS platforms, the SCP_BL2/2U image is loaded below
BL1 read-write data. This same memory is used to load BL31
later on. But sufficient checks were not done to ensure that the
SCP_BL2 would not overwrite BL1 rw data. This patch adds the
required CASSERT checks to prevent overwrite into BL1 or BL2
memory by load of SCP_BL2/2U. Also the size of BL31 is increased
and SCP_BL2/2U size is decreased to accomodate it within the
allocated region.
Change-Id: I23b28b5e1589e91150852a06452bd52b273216ee
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch makes the necessary changes to enable ARM platform to
successfully integrate CryptoCell during Trusted Board Boot. The
changes are as follows:
* A new build option `ARM_CRYPTOCELL_INTEG` is introduced to select
the CryptoCell crypto driver for Trusted Board boot.
* The TrustZone filter settings for Non Secure DRAM is modified
to allow CryptoCell to read this memory. This is required to
authenticate BL33 which is loaded into the Non Secure DDR.
* The CSS platforms are modified to use coherent stacks in BL1 and BL2
when CryptoCell crypto is selected. This is because CryptoCell makes
use of DMA to transfer data and the CryptoCell SBROM library allocates
buffers on the stack during signature/hash verification.
Change-Id: I1e6f6dcd1899784f1edeabfa2a9f279bbfb90e31
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
SPE is only supported in non-secure state. Accesses to SPE specific
registers from SEL1 will trap to EL3. During a world switch, before
`TTBR` is modified the SPE profiling buffers are drained. This is to
avoid a potential invalid memory access in SEL1.
SPE is architecturally specified only for AArch64.
Change-Id: I04a96427d9f9d586c331913d815fdc726855f6b0
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
On ARM platforms before exiting from SP_MIN ensure that
the default console is switched to the runtime serial port.
Change-Id: I0ca0d42cc47e345d56179eac16aa3d6712767c9b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch adds the memory map region for the SCMI payload memory
and maps the Juno core indices to SCMI power domains via the
`plat_css_core_pos_to_scmi_dmn_id_map` array.
Change-Id: I0d2bb2a719ff5b6a9d8e22e91e1625ab14453665
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds the SCMI driver for communicating with SCP. The power
domain management and system power management protocol of the SCMI
specification[1] is implemented in the driver. The SCP power management
abstraction layer for SCMI for CSS power management is also added.
A new buid option `CSS_USE_SCMI_DRIVER` is introduced to select SCMI
driver over SCPI.
[1] ARM System Control and Management Interface v1.0 (SCMI)
Document number: ARM DEN 0056A
Change-Id: I67265615a17e679a2afe810b9b0043711ba09dbb
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Platforms aligned with TBBR are supposed to use their own OIDs, but
defining the same macros with different OIDs does not provide any
value (at least technically).
For easier use of TBBR, this commit allows platforms to reuse the OIDs
obtained by ARM Ltd. This will be useful for non-ARM vendors that
do not need their own extension fields in their certificate files.
The OIDs of ARM Ltd. have been moved to include/tools_share/tbbr_oid.h
Platforms can include <tbbr_oid.h> instead of <platform_oid.h> by
defining USE_TBBR_DEFS as 1. USE_TBBR_DEFS is 0 by default to keep the
backward compatibility.
For clarification, I inserted a blank line between headers from the
include/ directory (#include <...>) and ones from a local directory
(#include "..." ).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for firmware upgrade on AArch32.
This patch has been tested on the FVP models.
NOTE: Firmware upgrade on Juno AArch32 is not currently supported.
Change-Id: I1ca8078214eaf86b46463edd14740120af930aec
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Co-Authored-By: Yatharth Kochar <yatharth.kochar@arm.com>
This patch adds `TRUSTED_BOARD_BOOT` support for AArch32 mode.
To build this patch the "mbedtls/include/mbedtls/bignum.h"
needs to be modified to remove `#define MBEDTLS_HAVE_UDBL`
when `MBEDTLS_HAVE_INT32` is defined. This is a workaround
for "https://github.com/ARMmbed/mbedtls/issues/708"
NOTE: TBBR support on Juno AArch32 is not currently supported.
Change-Id: I86d80e30b9139adc4d9663f112801ece42deafcf
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Co-Authored-By: Yatharth Kochar <yatharth.kochar@arm.com>
In AArch64, privileged exception levels control the execution state
(a.k.a. register width) of the immediate lower Exception Level; i.e.
whether the lower exception level executes in AArch64 or AArch32 state.
For an exception level to have its execution state changed at run time,
it must request the change by raising a synchronous exception to the
higher exception level.
This patch implements and adds such a provision to the ARM SiP service,
by which an immediate lower exception level can request to switch its
execution state. The execution state is switched if the request is:
- raised from non-secure world;
- raised on the primary CPU, before any secondaries are brought online
with CPU_ON PSCI call;
- raised from an exception level immediately below EL3: EL2, if
implemented; otherwise NS EL1.
If successful, the SMC doesn't return to the caller, but to the entry
point supplied with the call. Otherwise, the caller will observe the SMC
returning with STATE_SW_E_DENIED code. If ARM Trusted Firmware is built
for AArch32, the feature is not supported, and the call will always
fail.
For the ARM SiP service:
- Add SMC function IDs for both AArch32 and AArch64;
- Increment the SiP service minor version to 2;
- Adjust the number of supported SiP service calls.
Add documentation for ARM SiP service.
FixesARM-software/tf-issues#436
Change-Id: I4347f2d6232e69fbfbe333b340fcd0caed0a4cea
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.
NOTE: Files that have been imported by FreeBSD have not been modified.
[0]: https://spdx.org/
Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
utils.h is included in various header files for the defines in it.
Some of the other header files only contain defines. This allows the
header files to be shared between host and target builds for shared defines.
Recently types.h has been included in utils.h as well as some function
prototypes.
Because of the inclusion of types.h conflicts exist building host tools
abd these header files now. To solve this problem,
move the defines to utils_def.h and have this included by utils.h and
change header files to only include utils_def.h and not pick up the new
types.h being introduced.
FixesARM-software/tf-issues#461
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Remove utils_def.h from utils.h
This patch removes utils_def.h from utils.h as it is not required.
And also makes a minor change to ensure Juno platform compiles.
Change-Id: I10cf1fb51e44a8fa6dcec02980354eb9ecc9fa29
The CSS power management layer previously allowed to suspend system
power domain level via both PSCI CPU_SUSPEND and PSCI SYSTEM_SUSPEND
APIs. System suspend via PSCI CPU_SUSPEND was always problematic to
support because of issues with targeting wakeup interrupts to
suspended cores before the per-cpu GIC initialization is done. This
is not the case for PSCI SYSTEM_SUSPEND API because all the other
cores are expected to be offlined prior to issuing system suspend and
PSCI CPU_ON explicit calls will be made to power them on. Hence the Juno
platform used to downgrade the PSCI CPU_SUSPEND request for system
power domain level to cluster level by overriding the default
`plat_psci_pm_ops` exported by CSS layer.
Given the direction the new CSS platforms are evolving, it is best to
limit the system suspend only via PSCI SYSTEM_SUSPEND API for all
CSS platforms. This patch makes changes to allow system suspend
only via PSCI SYSTEM_SUSPEND API. The override of `plat_psci_ops`
for Juno is removed.
Change-Id: Idb30eaad04890dd46074e9e888caeedc50a4b533
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds support for SP_MIN on JUNO platform.
The changes include addition of AArch32 assembly files,
JUNO specific SP_MIN make file and miscellaneous changes
in ARM platform files to enable support for SP_MIN.
Change-Id: Id1303f422fc9b98b9362c757b1a4225a16fffc0b
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Following steps are required to boot JUNO in AArch32 state:
1> BL1, in AArch64 state, loads BL2.
2> BL2, in AArch64 state, initializes DDR.
Loads SP_MIN & BL33 (AArch32 executable)images.
Calls RUN_IMAGE SMC to go back to BL1.
3> BL1 writes AArch32 executable opcodes, to load and branch
at the entrypoint address of SP_MIN, at HI-VECTOR address and
then request for warm reset in AArch32 state using RMR_EL3.
This patch makes following changes to facilitate above steps:
* Added assembly function to carry out step 3 above.
* Added region in TZC that enables Secure access to the
HI-VECTOR(0xFFFF0000) address space.
* AArch32 image descriptor is used, in BL2, to load
SP_MIN and BL33 AArch32 executable images.
A new flag `JUNO_AARCH32_EL3_RUNTIME` is introduced that
controls above changes. By default this flag is disabled.
NOTE: BL1 and BL2 are not supported in AArch32 state for JUNO.
Change-Id: I091d56a0e6d36663e6d9d2bb53c92c672195d1ec
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
ARM platforms have migrated to the translation tables library v2.
However, for testing purposes, it can be useful to temporarily switch
back to the old version.
This patch introduces the option `ARM_XLAT_TABLES_LIB_V1`, that switches
to v1 of the library when is set to 1. By default, it is 0, so that ARM
platforms use the new version unless specifically stated.
Updated User Guide.
Change-Id: I53d3c8dd97706f6af9c6fca0364a88ef341efd31
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Some header files using the ULL() macro were not directly including
utils.h where the macro definition resides. As a consequence, a linker
script with values using this macro did not see the macro definition
and kept the "ULL(<value>)" call in the preprocessed file, which lead to
link error.
Files using ULL() macro now include utils.h directly.
Change-Id: I433a7f36bd21a156c20e69bc2a2bb406140ebdf9
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
Introduce new build option ENABLE_STACK_PROTECTOR. It enables
compilation of all BL images with one of the GCC -fstack-protector-*
options.
A new platform function plat_get_stack_protector_canary() is introduced.
It returns a value that is used to initialize the canary for stack
corruption detection. Returning a random value will prevent an attacker
from predicting the value and greatly increase the effectiveness of the
protection.
A message is printed at the ERROR level when a stack corruption is
detected.
To be effective, the global data must be stored at an address
lower than the base of the stacks. Failure to do so would allow an
attacker to overwrite the canary as part of an attack which would void
the protection.
FVP implementation of plat_get_stack_protector_canary is weak as
there is no real source of entropy on the FVP. It therefore relies on a
timer's value, which could be predictable.
Change-Id: Icaaee96392733b721fa7c86a81d03660d3c1bc06
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
This API makes sure that all the characters sent to the crash console
are output before returning from it.
Porting guide updated.
Change-Id: I1785f970a40f6aacfbe592b6a911b1f249bb2735
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch modifies some of the functions in ARM platform layer to cater
for the case when multi-threading `MT` is set in MPIDR. A new build flag
`ARM_PLAT_MT` is added, and when enabled, the functions accessing MPIDR
now assume that the `MT` bit is set for the platform and access the bit
fields accordingly.
Also, a new API plat_arm_get_cpu_pe_count is added when `ARM_PLAT_MT` is
enabled, returning the PE count within the physical cpu corresponding to
`mpidr`.
Change-Id: I04ccf212ac3054a60882761f4087bae299af13cb
Signed-off-by: Summer Qin <summer.qin@arm.com>
Modify ARM common makefile to use version 2 of the translation tables
library and include the new header in C files.
Simplify header dependencies related to this library to simplify the
change.
The following table contains information about the size increase in
bytes for BL1 after applying this patch. The code has been compiled for
different configurations of FVP in AArch64 mode with compiler GCC 4.9.3
20150413. The sizes have been calculated with the output of `nm` by
adding the size of all regions and comparing the total size before and
after the change. They are sumarized in the table below:
text bss data total
Release +660 -20 +88 +728
Debug +740 -20 +242 +962
Debug (LOG_LEVEL=50) +1120 -20 +317 +1417
Change-Id: I539e307f158ab71e3a8b771640001fc1bf431b29
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Added APIs to add and remove regions to the translation tables
dynamically while the MMU is enabled. Only static regions are allowed
to overlap other static ones (for backwards compatibility).
A new private attribute (MT_DYNAMIC / MT_STATIC) has been added to
flag each region as such.
The dynamic mapping functionality can be enabled or disabled when
compiling by setting the build option PLAT_XLAT_TABLES_DYNAMIC to 1
or 0. This can be done per-image.
TLB maintenance code during dynamic table mapping and unmapping has
also been added.
FixesARM-software/tf-issues#310
Change-Id: I19e8992005c4292297a382824394490c5387aa3b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Due to incorrect conditional compilation checks, bakery locks were
excluded from the CCN driver and the power controller driver for FVP
when BL32 was built as the EL3 Runtime Software in AArch32 mode.
This patch corrects the same.
Change-Id: Ib1f163d9167a5c38e4d622232c4835cad9c235aa
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
davidcunado-arm
Qixiang Xu
Soby Mathew
Sandrine Bailleux
danh-arm
Jeenu Viswambharan
Jens Wiklander
Roberto Vargas
Summer Qin
Dimitris Papastamos
Masahiro Yamada
Yatharth Kochar
Scott Branden
Scott Branden
Antonio Nino Diaz
Douglas Raillard