The Allwinner SID device holds a 16-bit SoC identifier, which we already
use in our code.
Export this number through the generic SMCCC SOCID interface, to allow
an architectural identification of an Allwinner SoC. This enables access
to this information from non-secure world, simplifies generic drivers
(ACPI comes to mind), and gives easy and precise access to the SoC ID
from userland in OSes like Linux.
Change-Id: I91753046b2ae5408ca7bc0b864fcd97d24c8267c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When using SCPI as the PSCI backend, firmware can wake up the CPUs and
cluster from sleep, so CPU idle states are available for the rich OS to
use. In that case, advertise them to the rich OS via the DTB.
Change-Id: I718ef6ef41212fe5213b11b4799613adbbe6e0eb
Signed-off-by: Samuel Holland <samuel@sholland.org>
Use the encoding recommended by the PSCI specification: four bits for
the power state at each power level.
SCPI provides no way to handshake an exit from a standby state, so the
only possible standby state is the architectural WFI state. Since WFI
can be used outside of PSCI, we do not allow passing in standby states.
Change-Id: I4b3b84e5c255ee58a25255a0cab5d7623425086e
Signed-off-by: Samuel Holland <samuel@sholland.org>
Aligning the PSCI and SCPI power states avoids some code to translate
between the two. This also makes room for an intermediate power state,
for future firmware capability growth.
Change-Id: I26691085f277a96bd405e3305ab0fe390a92b418
Signed-off-by: Samuel Holland <samuel@sholland.org>
Currently, if any step of the DTB patching process fails, the whole
process is aborted. However, this causes some problems:
- If any step modifies the DTB (including fdt_open_into), the dcache
must still be cleaned, even if some later step fails.
- The DTB may need changes in multiple places; if one patch fails (for
example due to missing nodes), we should still apply other patches.
- Similarly, if some patch fails, we should still run fdt_pack to
clean up after ourselves.
Change-Id: If1af2e58e5a7edaf542354bb8a261dd1c3da1ad0
Signed-off-by: Samuel Holland <samuel@sholland.org>
Idle states are advertised to the rich OS by declaring them in the DTB.
Since the availability of idle states depends on which PSCI
implementation was chosen, the DTB must be updated after PSCI setup.
Move this operation to bl31_plat_runtime_setup, the platform hook
which happens at the right time. Defining this hook overrides the weak
definition from plat/common, so copy over the code from there, too.
Change-Id: I42a83edb9cb28e1803d17dc2d73dbc879d885222
Signed-off-by: Samuel Holland <samuel@sholland.org>
So far the H616 was the only Allwinner SoC needed to amend the DTB, to
reserve the DRAM portion that BL31 occupies.
To allow other SoCs to modify the DTB as well, without duplicating code,
move the DTB change routines into Allwinner common code, and generalise
the current code to allow other modifications.
No functional change intended.
Change-Id: I080ea07b6470367f3c2573a4368f8ef5196d411c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
For somewhat historical reasons we are doing some initial PMIC regulator
setup in BL31, as U-Boot does not (yet) have a PMIC driver. This worked
fine so far, but there is at least one board (OrangePi 3) that gets upset,
because the Ethernet PHY needs some *coordinated* bringup of *two*
regulators.
To avoid custom hacks, let's introduce a build option to keep doing the
regulator setup in TF-A. Defining SUNXI_SETUP_REGULATORS to 0 will break
support for some devices on some boards in U-Boot (Ethernet and HDMI),
but will allow to bring up the OrangePi 3 in Linux correctly. We keep
the default at 1 to not change the behaviour for all other boards.
After U-Boot gained proper PMIC support at some point in the future, we
will probably change the default to 0, to get rid of the less optimal
PMIC code in TF-A.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Change-Id: Ie8e2583d0396f6eeaae8ffe6b6190f27db63e2a7
Allwinner R329 is a new dual-core Corte-A53 SoC. Add basical TF-A
support for it, to provide a PSCI implementation containing CPU
boot/shutdown and SoC reset.
Change-Id: I0fa37ee9b4a8e0e1137bf7cf7d614b6ca9624bfe
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Not all Allwinner SoCs have the same arrangement to SRAM A2.
Allow to specify a offset at which BL31 will stay in SRAM A2.
Change-Id: I574140ffd704a796fae0a5c2d0976e85c7fcbdf9
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
In newer Allwiner SoCs, the AA64nAA32 wires are mapped to a new register
called "General Control Register0" in the manual rather than the
"Cluster 0 Control Register0" in older SoCs.
Now the position of AA64nAA32 (reg and bit offset) is defined in a few
macros instead assumed to be at bit offset 24 of
SUNXI_CPUCFG_CLS_CTRL_REG0.
Change-Id: I933d00b9a914bf7103e3a9dadbc6d7be1a409668
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Adds a 1us delay after enabling power to a CPU core, to prevent
inrush-caused CPU crash before it's up.
Change-Id: I8f4c1b0dc0d1d976b31ddc30efe7a77a1619b1b3
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Group the SCP base/size definitions in a more logical location.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Id43f9b468d7d855a2413173d674a5ee666527808
BL31 does not appear to ever access the DRAM allocated to BL32,
so there is no need to map it at EL3.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie8727b793e53ea14517894942266f6da0333eb74
The SRAM on Allwinner platforms is shared between BL31 and coprocessor
firmware. Previously, SRAM was mapped as normal memory by default.
This scheme requires carveouts and cache maintenance code for proper
synchronization with the coprocessor.
A better scheme is to only map pages owned by BL31 as normal memory,
and leave everything else as device memory. This removes the need for
cache maintenance, and it makes the mapping for BL31 RW data explicit
instead of magic.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I820ddeba2dfa2396361c2322308c0db51b55c348
This constant specifically refers to the number of static mmap regions.
Rename it to make that clear.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I475c037777ce2a10db2631ec0e7446bb73590a36
When the BL31 for the Allwinner H616 runs in DRAM, we need to make sure
we tell the non-secure world about the memory region it uses.
Add a reserved-memory node to the DT, which covers the area that BL31
could occupy. The "no-map" property will prevent OSes from mapping
the area, so there would be no speculative accesses.
Change-Id: I808f3e1a8089da53bbe4fc6435a808e9159831e1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The new Allwinner H616 SoC lacks the management controller and the secure
SRAM A2, so we need to tweak the memory map quite substantially:
We run BL31 in DRAM. Since the DRAM starts at 1GB, we cannot use our
compressed virtual address space (max 256MB) anymore, so we revert to
the full 32bit VA space and use a flat mapping throughout all of it.
The missing controller also means we need to always use the native PSCI
ops, using the CPUIDLE hardware, as SCPI and suspend depend on the ARISC.
Change-Id: I77169b452cb7f5dc2ef734f3fc6e5d931749141d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In preparation for changing the memory map, express the locations of the
various code and data pieces more dynamically, allowing SoCs to override
the memmap later.
Also prepare for the SCP region to become optional.
No functional change.
Change-Id: I7ac01e309be2f23bde2ac2050d8d5b5e3d6efea2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The code to power the current core off when SCPI is not available is now
different for the two supported SoC families.
To make adding new platforms easier, move sunxi_cpu_power_off_self()
into the SoC directory, so we don't need to carry definitions for both
methods for all SoCs.
On the H6 we just need to trigger the CPUIDLE hardware, so can get rid
of all the code to program the ARISC, which is now only needed for the
A64 version.
Change-Id: Id2a1ac7dcb375e2fd021b441575ce86b4d7edf2c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For the existing SoCs we support, we use SEPARATE_NOBITS_REGION, to move
some parts of the data into separate memory regions (to save on the SRAM
A2 we are loaded into).
For the upcoming H616 platform this is of no concern (we run in DRAM),
so make this flag a platform choice instead.
Change-Id: Ic01d49578c6274660f8f112bd23680d3eca3be7a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The upcoming refactoring to support the new H616 SoCs will push the A64
build over the edge, by using more than the 48KB of SRAM available.
To reduce the code size, set some libfdt options that aim to reduce
sanity checks (for saving code space):
- ASSUME_LATEST: only allow v17 DTBs (as created by dtc)
- ASSUME_NO_ROLLBACK: don't prepare for failed DT additions
- ASSUME_LIBFDT_ORDER: assume sane ordering, as done by dtc
Change-Id: I12c93ec09e7587c5ae71e54947f817c32ce5fd6d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This works even on SoCs that do not have an ARISC, and it avoids
clobbering whatever ARISC firmware might be running.
Change-Id: I9f2fed597189bb387de79e8e76a7da3375e1ee91
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that we have split the native and the SCPI version of the PSCI ops,
we can introduce build options to compile in either or both of them.
If one version is not compiled in, some stub functions make sure the
common code still compiles and makes the right decisions.
By default both version are enabled (as before), but one of them can be
disabled on the make command line, or via a platform specific Makefile.
Change-Id: I0c019d8700c0208365eacf57809fb8bc608eb9c0
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
In order to keep SCP firmware as optional, the original, limited native
PSCI implementation was kept around as a fallback. This turned out to be
a good decision, as some newer SoCs omit the ARISC, and thus cannot run
SCP firmware.
However, keeping the two implementations in one file makes things
unnecessarily messy. First, it is difficult to compile out the
SCPI-based implementation where it is not applicable. Second the check
is done in each callback, while scpi_available is only updated at boot.
This makes the individual callbacks unnecessarily complicated.
It is cleaner to provide two entirely separate implementations in two
separate files. The native implementation does not support any kind of
CPU suspend, so its callbacks are greatly simplified. One function,
sunxi_validate_ns_entrypoint, is shared between the two implementations.
Finally, the logic for choosing between implementations is kept in a
third file, to provide for platforms where only one implementation is
applicable and the other is compiled out.
Change-Id: I4914f07d8e693dbce218e0e2394bef15c42945f8
Signed-off-by: Samuel Holland <samuel@sholland.org>
- When the SCPI shutdown/reset command returns success, the SCP is
still waiting for the CPU to enter WFI. Do that.
- Peform board-level poweroff before CPU poweroff. If there is a PMIC
available, it will turn everything off including the CPUs, so doing
CPU poweroff first is a waste of cycles.
- During poweroff, attempt to turn off the local CPU using the ARISC.
This should use slightly less power than just an infinite WFI.
- Drop the WFI in the reset failure path. The panic will hang anyway.
Change-Id: I897efecb3fe4e77a56041b97dd273156ec51ef8e
Signed-off-by: Samuel Holland <samuel@sholland.org>
When operating on the local cpu, sunxi_cpu_power_off_self() only "arms"
the ARISC to perform the power-off process; the SCP waits for the CPU to
enter WFI before acutally powering it off. Since this matches the
expected split between .pwr_domain_off and .pwr_domain_pwr_down_wfi, we
can move the sunxi_cpu_power_off_self() call to sunxi_pwr_domain_off().
Since that change makes sunxi_pwr_down_wfi() equivalent to the default
implementation, the callback is no longer needed.
Change-Id: I7d65f66c550d1c69fa5e9945affd7a25b3d3ef42
Signed-off-by: Samuel Holland <samuel@sholland.org>
Currently, sunxi_cpu_off() has two separate code paths: one for the
local CPU, and one for other CPUs. Let's split them in to two functions.
This actually simplifies things, because all callers either operate on
the local CPU only (sunxi_pwr_down_wfi()) or other CPUs only
(sunxi_cpu_power_off_others()). This avoids needing a second MPIDR read
to choose the appropriate code path.
Change-Id: I55de85025235cc95466bfa106831fc4c2368f527
Signed-off-by: Samuel Holland <samuel@sholland.org>
Disabling secondary CPUs during boot is unnecessary because the other
CPUs are already in reset, and it saves an entirely insignificant amount
of power. Let's remove this bit of code that was added mostly "because
we can", and along with it remove an unconditional dependency on the CPU
ops functions.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ia77a1b722da6ba989c3992b656a6cde3f2238fd7
Checking the exceptional case and letting the success case fall through
is not only more idiomatic, but it also allows adding more exceptional
cases in the future, such as a check for overlapping secure DRAM.
Change-Id: I720441a6a8853fd7f211ebe851f14d921a6db03d
Signed-off-by: Samuel Holland <samuel@sholland.org>
This duplicated the logic in psci_validate_mpidr() which was already
called from psci_cpu_on().
Change-Id: I96ee92f1ce3e9cc2985b4e229ba86ebd27b79915
Signed-off-by: Samuel Holland <samuel@sholland.org>
This optional PSCI function was only implemented when SCPI was
available. However, the underlying SCPI function is not able to fulfill
the necessary contract. First, the SCPI protocol has no way to represent
HW_STANDBY at the CPU power level. Second, the SCPI implementation
maintains its own logical view of power states, and its implementation
of SCPI_CMD_GET_CSS_POWER_STATE does not actually query the hardware.
Thus it cannot provide "the physical view of power state", as required
for this function by the PSCI specification.
Since the function is optional, drop it.
Change-Id: I5f3a0810ac19ddeb3c0c5d35aeb09f09a0b80c1d
Signed-off-by: Samuel Holland <samuel@sholland.org>
RSB is faster and more efficient, and it has a simpler driver. As long
as the PMIC is returned to I2C mode after use, the rich OS can later use
either bus.
Change-Id: I0c5f32e88a090c8c5cccb81bd24596b301ab9da7
Signed-off-by: Samuel Holland <samuel@sholland.org>
This gives the rich OS the flexibility to choose between I2C and RSB
communication. Since a runtime address can only be assigned once after
entering RSB mode, it also lets the rich OS choose any runtime address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Id49c124c5e925985fc31c0ba38c7fb6c941aafa8
None of the other drivers (Linux, U-Boot, Crust) need to lower the bus
clock frequency to switch the PMIC to RSB mode. That logic is not needed
here, either. The hardware takes care of running this transaction at the
correct bus frequency.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Idcfe933df4da75d5fd5a4f3e362da40ac26bdad1
BL31 reports the following warning during boot:
WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing!
Resolve this by enabling the workaround on the affected platforms.
Change-Id: Ia1d5075370be5ae67b7bece96ec0069d9692b14c
Signed-off-by: Samuel Holland <samuel@sholland.org>
While the Allwinner platform code nominally supported a custom
PRELOADED_BL33_BASE, some references to the BL33 load address used
another constant: PLAT_SUNXI_NS_IMAGE_OFFSET. To allow the DTB search
code to work if a U-Boot BL33 is loaded to a custom address,
consistently use PRELOADED_BL33_BASE. And to avoid this confusion in
the future, remove the other constant.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie6b97ae1fdec95d784676aef39200bef161471b0
The H6 has a "secure port controller" similar to the A64/H5, but with
more ports and a different register layout. Split the platform-specific
parts out into a header, and add the missing MMIO base address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I3703868bc595459ecf9568b9d1605cb1be014bf5
H6 has a reorganized R_PRCM compared to A64/H5, with the security switch
at a different offset. Until now, we did not notice, because the switch
has no effect unless the secure mode e-fuse is blown.
Since we are adding more platform-specific CCU registers, move them to
their own header, and out of the memory map (where they do not belong).
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie77476db0515080954eaa2e32bf6c3de657cda86
Compiling BL31 for the Allwinner platform now produces a message about
the deprecation of gic_common.c.
Follow the advice and use include gicv2.mk instead.
Collect all includes at the beginning of the file on the way.
Change-Id: Iee46e21a630bfa831d28059f09aa7b049eb554bb
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The non-secure world has no business accessing the CPU power switches in
the PRCM; those are handled by TF-A or the SCP. Only allow access to the
clock control part of the PRCM.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I657b97f4ea8a0073448ad3343fbc66ba168ed89e
The base address for both the GPIO and the clock unit of the H6 memory map
have been typo-ed. Fix them to match the Linux DT and the manual.
The H6 code use neither of them, so this doesn't change or fix anything
in the real world, but should be corrected anyway.
The issue was found and reported by Github user "armlabs".
Change-Id: Ic6fdfb732ce1cfc54cbb927718035624a06a9e08
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara
Samuel Holland
Icenowy Zheng
Olivier Deprez