In order to prepare future support of FIP, BL32 (SP_min) is compiled
as Position Independent Executable.
Change-Id: I15e7cc433fb03e1833002f4fe2eaecb6ed42eb47
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
BL2 size is set to 100kB, and BL32 to 72kB, regardless of OP-TEE
or stack protector flags.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Id7411bd55a4140718d64a647d81037720615fc81
Only BL32 (SP_min) is supported at the moment, BL1 and BL2_AT_EL3 are just
stubbed with _pie_fixup_size=0.
The changes are an adaptation for AARCH32 on what has been done for
PIE support on AARCH64.
The RELA_SECTION is redefined for AARCH32, as the created section is
.rel.dyn and the symbols are .rel*.
Change-Id: I92bafe70e6b77735f6f890f32f2b637b98cf01b9
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The use of end addresses is preferred over the size of sections.
This was done for some AARCH64 files for PIE with commit [1],
and some extra explanations can be found in its commit message.
Align the missing AARCH64 files.
For AARCH32 files, this is required to prepare PIE support introduction.
[1] f1722b693d ("PIE: Use PC relative adrp/adr for symbol reference")
Change-Id: I8f1c06580182b10c680310850f72904e58a54d7d
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The Arm Generic Timer specification mandates that the
interrupt associated with each timer is low level triggered,
see:
Arm Cortex-A76 Core:
"Each timer provides an active-LOW interrupt output to the SoC."
Arm Cortex-A53 MPCore Processor:
"It generates timer events as active-LOW interrupt outputs and
event streams."
The following files in fdts\
fvp-base-gicv3-psci-common.dtsi
fvp-base-gicv3-psci-aarch32-common.dtsi
fvp-base-gicv2-psci-aarch32.dts
fvp-base-gicv2-psci.dts
fvp-foundation-gicv2-psci.dts
fvp-foundation-gicv3-psci.dts
describe interrupt types as edge rising
IRQ_TYPE_EDGE_RISING = 0x01:
interrupts = <1 13 0xff01>,
<1 14 0xff01>,
<1 11 0xff01>,
<1 10 0xff01>;
, see include\dt-bindings\interrupt-controller\arm-gic.h:
which causes Linux to generate the warnings below:
arch_timer: WARNING: Invalid trigger for IRQ5, assuming level low
arch_timer: WARNING: Please fix your firmware
This patch adds GIC_CPU_MASK_RAW macro definition to
include\dt-bindings\interrupt-controller\arm-gic.h,
modifies interrupt type to IRQ_TYPE_LEVEL_LOW and
makes use of type definitions in arm-gic.h.
Change-Id: Iafa2552a9db85a0559c73353f854e2e0066ab2b9
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Counter frequency for generic timer of Arm-A53 based Application
Processing Unit(APU) is not configuring in case if First Stage Boot
Loader(FSBL) does not initialize counter frequency. This happens
when FSBL is running from Arm-R5 based Real-time Processing Unit(RPU).
Because of that generic timer driver functionality is not working.
So configure counter frequency during initialization.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Icfccd59d7d2340fba25ebfb2ef6a813af4290896
Add support for CRC checksum for IPI data when the macro
IPI_CRC_CHECK is enabled.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I3c25c715885759076055c6505471339b5d6edcd5
Rename the macro ZYNQMP_IPI_CRC_CHECK to IPI_CRC_CHECK and
move the related defines to the common include.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I6d30b081ac607572a0b23e10ca8031bc90489e58
ELP processors can sometimes have different MIDR values or features so
we are adding the "_arm" suffix to differentiate the reference
implementation from other future versions.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Ieea444288587c7c18a397d279ee4b22b7ad79e20
In the case of a SP pre-empted by a non-secure interrupt, the SPMC
returns to the SPMD through the FFA_INTERRUPT ABI. It is then forwarded
to the normal world driver hinting the SP has to be resumed after the
non-secure interrupt has been serviced.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I51a694dddcb8ea30fa84e1f11d018bc2abec0a56
As per FF-A v1.0 spec, Table 3.1, messaging method field also contains
information about whether partition supports managed exit or not.
Since a partition can support managed exit only if it supports direct
messaging, so there are two new possible values, managed exit with only
direct messaging or with both messaging methods.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ic77cfb37d70975c3a36c56f8b7348d385735f378
Add support to identify Silicon Linux RZ/G2E evaluation kit (EK874).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Id7bdbc9b0d25aa9af496d58d4bd5055579edc104
Add pin control support for RZ/G2E SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I736724cc0dd32f2169018ed7f2f48319b039b61f
DRAM initialization on RZ/G2E SoC is identical to R-Car E3 so re-use the
same.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I454fb40af4f8ce6c4c0d2a53edb307326efd02df
Add pin control support for RZ/G2N SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Ib5eb4f3b1b75e158ec13c4eefdbe9688344206a3
Add support for initializing DRAM on RZ/G2N SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Id09a367b92b11a5da88f2dce6887677cc935d0c0
Add pin control support for RZ/G2H SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I06dc259d7d26a5a5313e8731ea72f846bfca09ed
Add support for initializing DRAM on RZ/G2H SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Iae23f1093f65a9efd065d37b7d6e9340ff6350b9
Switch using common ddr driver code from renesas/common/ddr directory
for RZ/G2M SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I807dcb0bc5186bd32bc1c577945d28634bb10e1f
Move ddr driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I9aef73d3e9a027a127ce7483b72d339559866727
By default the Arm Ethos-N NPU will boot up in secure mode. In this mode
the non-secure world cannot access the registers needed to use the NPU.
To still allow the non-secure world to use the NPU, a SiP service has
been added that can delegate non-secure access to the registers needed
to use it.
Only the HW_CONFIG for the Arm Juno platform has been updated to include
the device tree for the NPU and the platform currently only loads the
HW_CONFIG in AArch64 builds.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I65dfd864042ed43faae0a259dcf319cbadb5f3d2
To make it possible to use the hw_config device tree for dynamic
configuration in BL31 on the Arm Juno platform. A placeholder hw_config
has been added that is included in the FIP and a Juno specific BL31
setup has been added to populate fconf with the hw_config.
Juno's BL2 setup has been updated to align it with the new behavior
implemented in the Arm FVP platform, where fw_config is passed in arg1
to BL31 instead of soc_fw_config. The BL31 setup is expected to use the
fw_config passed in arg1 to find the hw_config.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: Ib3570faa6714f92ab8451e8f1e59779dcf19c0b6
* changes:
plat/marvell: remove subversion from Marvell make files
drivers/marvell: check if TRNG unit is present
plat/marvell: a8k: move efuse definitions to separate header
plat/marvell/armada: fix TRNG return SMC handling
drivers: marvell: comphy: add rx training on 10G port
plat/marvell/armada: postpone MSS CPU startup to BL31 stage
plat: marvell: armada: a8k: Fix LD selector mask
plat/marvell/armada: allow builds without MSS support
drivers: marvell: misc-dfx: extend dfx whitelist
drivers: marvell: add support for secure read/write of dfx register-set
ddr_phy: use smc calls to access ddr phy registers
drivers: marvell: thermal: use dedicated function for thermal SiPs
drivers: marvell: add thermal sensor driver and expose it via SIP service
fix: plat: marvell: fix MSS loader for A8K family
Subversion is not reflecting the Marvell sources variant anymore.
This patch removes version.mk from Marvell plafroms.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: I8f3afbe3fab3a38da68876f77455f449f5fe0179
Some Marvell SoCs may have crypto engine disabled in the HW.
This patch checks the AP LD0 efuse for crypto engine/TRNG
presence before initializing the driver.
Change-Id: I441e7c69a137106bd36302b028b04c0b31896dbd
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/47314
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Yi Guo <yi.guo@cavium.com>
Move efuse definitions to a separate header file for later
usage with other FW modules.
Change-Id: I2e9465f760d0388c8e5863bc64a4cdc57de2417f
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/47313
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Yi Guo <yi.guo@cavium.com>
Use single 64b register for the return value instead of two 32b.
Report an error if caller requested larger than than 64b random
number in a single SMC call.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: Ib8756cd3c0808b78c359f90c6f6913f7d16ac360
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/33280
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
This patch forces rx training on 10G ports
as part of comphy_smc call from Linux.
Signed-off-by: Alex Evraev <alexev@marvell.com>
Change-Id: Iebe6ea7c8b21cbdce5c466c8a69b92e9d7c8a8ca
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/30763
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Normally the CP MSS CPU was started at the end of FW load to IRAM at BL2.
However, (especailly in secure boot mode), some bus attributes should be
changed from defaults before the MSS CPU tries to access shared resources.
This patch starts to use CP MSS SRAM for FW load in both secure and
non-secure boot modes.
The FW loader inserts a magic number into MSS SRAM as an indicator of
successfully loaded FS during the BL2 stage and skips releasing the MSS
CPU from the reset state.
Then, at BL31 stage, the MSS CPU is released from reset following the
call to cp110_init function that handles all the required bus attributes
configurations.
Change-Id: Idcf81cc350a086835abed365154051dd79f1ce2e
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/46890
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Fixed a bug that the actually bit number was used as a mask to
select LD0 or LD1 fuse
Signed-off-by: Guo Yi <yguo@cavium.com>
Change-Id: I4bec268c3dc2566350b4a73f655bce222707e25b
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/46146
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Setting MSS_SUPPORT to 0 also removes requirement for SCP_BL2
definition.
Images build with MSS_SUPPORT=0 will not include service CPUs
FW and will not support PM, FC and other features implemented
in these FW images.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: Idf301ebd218ce65a60f277f3876d0aeb6c72f105
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/37769
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Linux cpu clk driver requires access to some dfx registers. By adding
these registers to the white list, we enable access to them from
non-secure world.
Change-Id: Ic05c96b375121c025bfb41c2ac9474a530720155
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/25187
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Since the dfx register set is going to be marked as secure expose dfx
secure read and write function via SiP services. In introduced misc_dfx
driver some registers are white-listed so non-secure software can still
access them.
This will allow non-secure word drivers access some white-listed
registers related to e.g.: Sample at reset, efuses, SoC type and
revision ID accesses.
Change-Id: If9ae2da51ab2e6ca62b9a2c940819259bf25edc0
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/25055
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Since more drivers which uses dfx register set need to be handled with
use of SiP services, use dedicated and more meaningful name for thermal
SiP services.
Change-Id: Ic2ac27535a4902477df8edc4c86df3e34cb2344f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/25054
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Manish Pandey
Yann Gautier
Yann Gautier
Alexei Fedorov
Joanna Farley
Rajan Vaja
Venkatesh Yadav Abbarapu
Olivier Deprez
johpow01
Lad Prabhakar
Madhukar Pappireddy
Mikael Olsson
Konstantin Porotchkin
Alex Evraev
Guo Yi
Grzegorz Jaszczyk
Alex Leibovich