Since LOAD_IMAGE_V2 is always enabled in HiKey960 platform. Drop
LOAD_IMAGE v1 to simplify code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
MAP_TSP_MEM could be either in SRAM or DRAM. When MAP_TSP_MEM is in
DRAM, it's overlapped with MAP_DDR.
Since TSP_MEM is always configured in DRAM case, it means
MAP_OPTEE_PAGEABLE is always disabled. Just remove it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The main difference between HiKey960 v1 hardware and HiKey960 v2
hardware is on UART console.
But the function of detecting boardid dumps message before console
ready. So fix it by removing those messages.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since non-TF ROM is used in HiKey platform (Hisilicon Hi6220 SoC),
replace BL1 by BL2_EL3 in normal boot mode.
When we recovery images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Although SRAM is initialized, DCACHE should be cleaned too.
Because MCU is a parrallel core to access SRAM. We need to make
sure that initialized value is really written to SRAM before
MCU using it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since LOAD_IMAGE_V2 is always enabled in HiKey platform. Drop
LOAD_IMAGE v1 to simplify code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
MAP_TSP_MEM could be either in SRAM or DRAM. When MAP_TSP_MEM is in
DRAM, it's overlapped with MAP_DDR.
Since MAP_OPTEE_PAGEABLE isn't used in SRAM case, just remove it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
`assert(e)` was used in place of `if (e) ERROR()` when sec_protect()
was ported from hikey fork so the logic should have been reversed.
Fixes: 3d5d9f5a ("hikey: configure the top 16MB of DRAM as secure")
Fixes: 52988b38 ("hikey: configure 4 MB of secure DRAM for OP-TEE
Secure Data Path")
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Victor Chong <victor.chong@linaro.org>
Update the memory firewall configuration to reserve 4 MB of secure RAM
for use by the kernel and OP-TEE as the Secure Data Path pool.
Note that this address range (0x3E800000 - 0x3EC00000) falls in the
range already set aside by UEFI (which reserves the upper 32 MB of the
1GB DRAM for OP-TEE [1]) and was previously unused.
[1] https://github.com/96boards-hikey/edk2/blob/hikey/HisiPkg/HiKeyPkg/Library/HiKeyLib/HiKeyMem.c#L44
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Victor Chong <victor.chong@linaro.org>
DRAM region 0x3f000000 - 0x3fffffff is reserved for OP-TEE and should
therefore be accessible only from secure world.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Victor Chong <victor.chong@linaro.org>
Let bl1 and bl2 have the ability to load images from emmc instead of
dram (mmap).
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
When some interrupts are configured as group 0 in GICv2, these
interrupts trigger FIQ signal; this results in the Linux kernel panic
by reporting log: "Bad mode in FIQ handler detected on CPU0, code
0x00000000 -- Unknown/Uncategorized". Unfortunately from kernel side it
has no permission to read the GIC register for group 0 interrupts so we
have no chance to get to know which interrupt is configured as secure
interrupt and cause the kernel panic.
For upper reason, this commit enables FIQ exception handling for
SPD_none case. If the system has not enabled SPD the FIQ interrupt is
trapped into EL3 and the FIQ handler can report the interrupt number so
we can easily narrow down which FIQ introduce unexpected interrupt.
After enable SPD we can rely on SPD interrupt route model to handle FIQ.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
At early time, the CPU CA73 retention state has been supported on
Hikey960. Later we found the system has the hang issue and for
resolving this issue Hisilicon released new MCU firmware, but
unfortunately the new MCU firmware has side effect and results in the
CA73 CPU cannot really enter retention state and roll back to WFI state.
After discussion we cannot see the possibility to enable CA73 retention
state anymore on Hikey960, based on this conclusion we should remove
this state supporting from ARM-TF and roll back to WFI state only. We
will commit one patch to remove CA73 CPU retention state in kernel DT
binding as well.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
This reverts commit fdae60b6ba.
The commit fdae60b6ba changed the
parameter encoding for the hikey960. However that implies a DT change
in the kernel side. After submitting the DT change for upstreaming,
the backward compatibility issue and the interface change raise some
concerns from the Linux community about the issues related to kernel <->
ATF alignment. There is no way to detect a mis-alignment of those
without a deep knowledge of the ATF and the kernel. Furthermore, the
failing calls to PSCI in the idle path (because of bad parameters), will
lead to busy looping, implying: thermal issues and extra energy
consumption.
In regard of the Linux community concerns, the potential issues when the
ATF and the kernel are not aligned, it is preferable to revert the
commit.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Co-authored-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
The security properties of some IP blocks are configured to secure mode
after reset. This means these IP blocks can only be accessed by cpus
in secure state by default. These should be configured correclty as needed.
Signed-off-by: y00241285 <yyangwei.yangwei@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
ARM Power State Coordination Interface (ARM DEN 0022D) chapter
6.5 "Recommended StateID Encoding" defines the state ID which can be
used by platforms. The recommended power states can be presented by
below values; and it divides into three fields, every field has 4 bits
to present power states corresponding to core level, cluster level and
system level.
0: Run
1: Standby
2: Retention
3: Powerdown
This commit changes to use upper recommended power states definition on
Hikey960; and changes the power state validate function to check the
power state passed from kernel side.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Pre-v8.2 platforms such as the Juno platform does not have
the Scalable Vector Extensions implemented and so the build
option ENABLE_SVE is set to zero.
This has a minor performance improvement with no functional
impact.
Change-Id: Ib072735db7a0247406f8b60e325b7e28b1e04ad1
Signed-off-by: David Cunado <david.cunado@arm.com>
Set alignment size to 512B so finally we can get fip.bin with 512B
alignment. This can avoid stuck issue for 'fastboot' downloading
if USB driver uses DMA for data transferring.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Set alignment size to 512B so finally we can get fip.bin with 512B
alignment. This can avoid stuck issue for 'fastboot' downloading if
USB driver uses DMA for data transferring.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
These macros are only defined for corresponding image,
and they are undefined for other images. It means that we have
to use ifdef or defined() instead of relying on being 0 by default.
Change-Id: Iad11efab9830ddf471599b46286e1c56581ef5a7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Init EDMA controller with non secure mode. A lot of peripherals are
depend on EDMA controller. But EDMA controller is in secure mode
by default. And this operation has to be executed in secure mode.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Otherwise, BL2 tries to load a BL32 image and triggers
assert(result == 0)
in
plat_get_image_source()
in hikey{960}_io_storage.c
in a debug build, or displays
ERROR: BL2: Failed to load image
in a release build.
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Every CPU has its own debug module and this module is used by JTAG
debugging and coresight tracing. If without enabling it, it's easily to
introduce lockup issue when we enable debugging features.
This patch is to enable CPU debug module when power on CPU; this allows
connecting to all cores through JTAG and used by kernel coresight
driver.
Signed-off-by: Matthias Welwarsky <maw@sysgo.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Constants named as *ACTLR* refer in fact to the CPUACTRL_EL1 register.
Since ACTLR and ACTRL_EL1 are different registers this patch renames
these constants for clarity.
Change-Id: I2a9e402dab7b0fcb6e481ee0d8a11eda943ed299
Signed-off-by: Eleanor Bonnici <Eleanor.bonnici@arm.com>
At the system boot time we need enable watchdog reset, otherwise after
the watchdog is timeout it cannot reset the SoC. We need set the bit 0
and bit 16 together, the bit 16 is mask bit so after set bit 16 we have
permission to operate bit 0 and bit 0 is watchdog reset enabling bit.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Clear the cpuidle flag when resuming from idle. This flag is set
when entering idle, and if it remains set when resuming, it can
prevent the cluster from powering off during the next system
suspend operation. During system suspend, all CPUs are plugged
out except the last CPU, which is suspended. If any of the
cpuidle flags are set at this point, the last CPU will be stuck
in a WFI loop and will not be powered off.
This problem only occurs during system suspend.
Signed-off-by: Tao Wang <kevin.wangtao@linaro.org>
Haojian Zhuang
Victor Chong
davidcunado-arm
Peter Griffin
Jerome Forissier
Leo Yan
Kaihua Zhong
Jiancheng Xue
Roberto Vargas
Jeenu Viswambharan
danh-arm
Eleanor Bonnici
Tao Wang