The DEVICE2 memory range is needed to access the Root of Trust Public
Key registers. This is not needed when Trusted Board Boot is disabled
so it's safer to not map it in this case. This also saves one level-2
page table in each of BL1 and BL2 images.
Also add some comments.
Change-Id: I67456b44f3fd5e145f6510a8499b7fdf720a7273
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
This fix modifies the order of #includes in ARM standard platforms
to meet the ARM TF coding standard.
Change-Id: Ide19aad6233babda4eea2d17d49e523645fed1b2
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>
SPE is only supported in non-secure state. Accesses to SPE specific
registers from SEL1 will trap to EL3. During a world switch, before
`TTBR` is modified the SPE profiling buffers are drained. This is to
avoid a potential invalid memory access in SEL1.
SPE is architecturally specified only for AArch64.
Change-Id: I04a96427d9f9d586c331913d815fdc726855f6b0
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
On ARM platforms before exiting from SP_MIN ensure that
the default console is switched to the runtime serial port.
Change-Id: I0ca0d42cc47e345d56179eac16aa3d6712767c9b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
ARM GIC-600 IP complies with ARM GICv3 architecture, but among others,
implements a power control register in the Redistributor frame. This
register must be programmed to mark the frame as powered on, before
accessing other registers in the frame. Rest of initialization sequence
remains the same.
The driver provides APIs for Redistributor power management, and
overrides those in the generic GICv3 driver. The driver data is shared
between generic GICv3 driver and that of GIC-600.
For FVP platform, the GIC-600 driver is chosen when FVP_USE_GIC_DRIVER
is set to FVP_GIC600. Also update user guide.
Change-Id: I321b2360728d69f6d4b0a747b2cfcc3fe5a20d67
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Both Cortex-A75 and Cortex-A55 CPUs use the ARM DynamIQ Shared Unit
(DSU). The power-down and power-up sequences are therefore mostly
managed in hardware, and required software operations are considerably
simpler.
Change-Id: I68b30e6e1ebe7c041d5e67f39c59f08575fc7ecc
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The default case is impossible to hit as the `power_level`
is already checked earlier. Avoids a clang warning.
Change-Id: I707463c843adc748ee9aa1d2313f9ab7dab3a8ab
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
The header tbbr_oid.h contains OIDs obtained by ARM Ltd.
so there is no good reason to use platform_oid.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Platforms aligned with TBBR are supposed to use their own OIDs, but
defining the same macros with different OIDs does not provide any
value (at least technically).
For easier use of TBBR, this commit allows platforms to reuse the OIDs
obtained by ARM Ltd. This will be useful for non-ARM vendors that
do not need their own extension fields in their certificate files.
The OIDs of ARM Ltd. have been moved to include/tools_share/tbbr_oid.h
Platforms can include <tbbr_oid.h> instead of <platform_oid.h> by
defining USE_TBBR_DEFS as 1. USE_TBBR_DEFS is 0 by default to keep the
backward compatibility.
For clarification, I inserted a blank line between headers from the
include/ directory (#include <...>) and ones from a local directory
(#include "..." ).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds `TRUSTED_BOARD_BOOT` support for AArch32 mode.
To build this patch the "mbedtls/include/mbedtls/bignum.h"
needs to be modified to remove `#define MBEDTLS_HAVE_UDBL`
when `MBEDTLS_HAVE_INT32` is defined. This is a workaround
for "https://github.com/ARMmbed/mbedtls/issues/708"
NOTE: TBBR support on Juno AArch32 is not currently supported.
Change-Id: I86d80e30b9139adc4d9663f112801ece42deafcf
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Co-Authored-By: Yatharth Kochar <yatharth.kochar@arm.com>
We used to have the following circular dependency in the FVP platform
header files:
+-> arm_def.h ---> platform_def.h ---> fvp_def.h --+
|__________________________________________________|
This patch breaks it by not including 'arm_def.h' from 'fvp_def.h'.
Change-Id: I280d906559e3343dd38764029e77c0ea768b4fec
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.
NOTE: Files that have been imported by FreeBSD have not been modified.
[0]: https://spdx.org/
Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Some header files using the ULL() macro were not directly including
utils.h where the macro definition resides. As a consequence, a linker
script with values using this macro did not see the macro definition
and kept the "ULL(<value>)" call in the preprocessed file, which lead to
link error.
Files using ULL() macro now include utils.h directly.
Change-Id: I433a7f36bd21a156c20e69bc2a2bb406140ebdf9
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
Introduce new build option ENABLE_STACK_PROTECTOR. It enables
compilation of all BL images with one of the GCC -fstack-protector-*
options.
A new platform function plat_get_stack_protector_canary() is introduced.
It returns a value that is used to initialize the canary for stack
corruption detection. Returning a random value will prevent an attacker
from predicting the value and greatly increase the effectiveness of the
protection.
A message is printed at the ERROR level when a stack corruption is
detected.
To be effective, the global data must be stored at an address
lower than the base of the stacks. Failure to do so would allow an
attacker to overwrite the canary as part of an attack which would void
the protection.
FVP implementation of plat_get_stack_protector_canary is weak as
there is no real source of entropy on the FVP. It therefore relies on a
timer's value, which could be predictable.
Change-Id: Icaaee96392733b721fa7c86a81d03660d3c1bc06
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
With GCC 6.2 compiler, more C undefined behaviour is being flagged as
warnings, which result in build errors in ARM TF build.
The specific issue that this patch resolves is the use of (1 << 31),
which is predominantly used in case statements, where 1 is represented
as a signed int. When shifted to msb the behaviour is undefined.
The resolution is to specify 1 as an unsigned int using a convenience
macro ULL(). A duplicate macro MAKE_ULL() is replaced.
FixesARM-software/tf-issues#438
Change-Id: I08e3053bbcf4c022ee2be33a75bd0056da4073e1
Signed-off-by: David Cunado <david.cunado@arm.com>
One nasty part of ATF is some of boolean macros are always defined
as 1 or 0, and the rest of them are only defined under certain
conditions.
For the former group, "#if FOO" or "#if !FOO" must be used because
"#ifdef FOO" is always true. (Options passed by $(call add_define,)
are the cases.)
For the latter, "#ifdef FOO" or "#ifndef FOO" should be used because
checking the value of an undefined macro is strange.
Here, IMAGE_BL* is handled by make_helpers/build_macro.mk like
follows:
$(eval IMAGE := IMAGE_BL$(call uppercase,$(3)))
$(OBJ): $(2)
@echo " CC $$<"
$$(Q)$$(CC) $$(TF_CFLAGS) $$(CFLAGS) -D$(IMAGE) -c $$< -o $$@
This means, IMAGE_BL* is defined when building the corresponding
image, but *undefined* for the other images.
So, IMAGE_BL* belongs to the latter group where we should use #ifdef
or #ifndef.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Earlier patches introduced GIC Redistributor power management for ARM
platforms. This patch modifies FVP power management to power down
Redistributor during CPU power on/off.
Change-Id: I2adb9c50a7dd750019fe3b4e576b5d5fc364bffb
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The capabilities exposed by the PSCI generic layer depends on the hooks
populated by the platform in `plat_arm_psci_pm_ops`. Currently ARM
Standard platforms statically define this structure. However, some
platforms may want to modify the hooks at runtime before registering
them with the generic layer.
This patch introduces a new ARM platform layer API
`plat_arm_psci_override_pm_ops` which allows the platform to probe
the power controller and modify `plat_arm_psci_pm_ops` if required.
Consequently, 'plat_arm_psci_pm_ops' is no longer qualified as
`const` on ARM Standard platforms.
Change-Id: I7dbb44b7bd36c20ec14ded5ee45a96816ca2ab9d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
There are many instances in ARM Trusted Firmware where control is
transferred to functions from which return isn't expected. Such jumps
are made using 'bl' instruction to provide the callee with the location
from which it was jumped to. Additionally, debuggers infer the caller by
examining where 'lr' register points to. If a 'bl' of the nature
described above falls at the end of an assembly function, 'lr' will be
left pointing to a location outside of the function range. This misleads
the debugger back trace.
This patch defines a 'no_ret' macro to be used when jumping to functions
from which return isn't expected. The macro ensures to use 'bl'
instruction for the jump, and also, for debug builds, places a 'nop'
instruction immediately thereafter (unless instructed otherwise) so as
to leave 'lr' pointing within the function range.
Change-Id: Ib34c69fc09197cfd57bc06e147cc8252910e01b0
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This prevents a warning being emitted in the console during FVP
configuration setup when using the Foundation FVP 9.6 onwards.
Change-Id: I685b8bd0dbd0119af4b0cb3f7d708fcc08e99561
This patch adds ARM Cortex-A32 MPCore Processor support
in the CPU specific operations framework. It also includes
this support for the Base FVP port.
Change-Id: If3697b88678df737c29f79cf3fa1ea2cb6fa565d
This patch adds support in SP_MIN to receive generic and
platform specific arguments from BL2.
The new signature is as following:
void sp_min_early_platform_setup(void *from_bl2,
void *plat_params_from_bl2);
ARM platforms have been modified to use this support.
Note: Platforms may break if using old signature.
Default value for RESET_TO_SP_MIN is changed to 0.
Change-Id: I008d4b09fd3803c7b6231587ebf02a047bdba8d0
This patch adds ARM platform changes in BL2 for AArch32 state.
It instantiates a descriptor array for ARM platforms describing
image and entrypoint information for `SCP_BL2`, `BL32` and `BL33`.
It also enables building of BL2 for ARCH=aarch32.
Change-Id: I60dc7a284311eceba401fc789311c50ac746c51e
This patch adds ARM platform changes in BL1 for AArch32 state.
It also enables building of BL1 for ARCH=aarch32.
Change-Id: I079be81a93d027f37b0f7d8bb474b1252bb4cf48
This patch adds common changes to support AArch32 state in
BL1 and BL2. Following are the changes:
* Added functions for disabling MMU from Secure state.
* Added AArch32 specific SMC function.
* Added semihosting support.
* Added reporting of unhandled exceptions.
* Added uniprocessor stack support.
* Added `el3_entrypoint_common` macro that can be
shared by BL1 and BL32 (SP_MIN) BL stages. The
`el3_entrypoint_common` is similar to the AArch64
counterpart with the main difference in the assembly
instructions and the registers that are relevant to
AArch32 execution state.
* Enabled `LOAD_IMAGE_V2` flag in Makefile for
`ARCH=aarch32` and added check to make sure that
platform has not overridden to disable it.
Change-Id: I33c6d8dfefb2e5d142fdfd06a0f4a7332962e1a3
This patch adds changes in ARM platform code to use new
version of image loading.
Following are the major changes:
-Refactor the signatures for bl31_early_platform_setup()
and arm_bl31_early_platform_setup() function to use
`void *` instead of `bl31_params_t *`.
-Introduce `plat_arm_bl2_handle_scp_bl2()` to handle
loading of SCP_BL2 image from BL2.
-Remove usage of reserve_mem() function from
`arm_bl1_early_platform_setup()`
-Extract BL32 & BL33 entrypoint info, from the link list
passed by BL2, in `arm_bl31_early_platform_setup()`
-Provides weak definitions for following platform functions:
plat_get_bl_image_load_info
plat_get_next_bl_params
plat_flush_next_bl_params
bl2_plat_handle_post_image_load
-Instantiates a descriptor array for ARM platforms
describing image and entrypoint information for
`SCP_BL2`, `BL31`, `BL32` and `BL33` images.
All the above changes are conditionally compiled using the
`LOAD_IMAGE_V2` flag.
Change-Id: I5e88b9785a3df1a2b2bbbb37d85b8e353ca61049
This patch implements FVP platform hook to support NODE_HW_STATE PSCI
API. The platform hook validates the given MPIDR and reads corresponding
status from FVP power controller, and returns expected values for the
PSCI call.
Change-Id: I286c92637da11858db2c8aba8ba079389032de6d
This patch adds a WFI instruction in the default implementations of
plat_error_handler() and plat_panic_handler(). This potentially reduces
power consumption by allowing the hardware to enter a low-power state.
The same change has been made to the FVP and Juno platform ports.
Change-Id: Ia4e6e1e5bf1ed42efbba7d0ebbad7be8d5f9f173
This patch implements the support for SP_MIN in FVP. The SP_MIN platform
APIs are implemented and the required makefile support is added for FVP.
Change-Id: Id50bd6093eccbd5e38894e3fd2b20d5baeac5452
This patch adds AArch32 support for FVP and implements common platform APIs
like `plat_get_my_stack`, `plat_set_my_stack`, `plat_my_core_cos` for AArch32.
Only Multi Processor(MP) implementations of these functions are considered in
this patch. The ARM Standard platform layer helpers are implemented for
AArch32 and the common makefiles are modified to cater for both AArch64 and
AArch32 builds. Compatibility with the deprecated platform API is not
supported for AArch32.
Change-Id: Iad228400613eec91abf731b49e21a15bcf2833ea
Compile option `ARM_BOARD_OPTIMISE_MMAP` has been renamed to
`ARM_BOARD_OPTIMISE_MEM` because it now applies not only to defines
related to the translation tables but to the image size as well.
The defines `PLAT_ARM_MAX_BL1_RW_SIZE`, `PLAT_ARM_MAX_BL2_SIZE` and
`PLAT_ARM_MAX_BL31_SIZE` have been moved to the file board_arm_def.h.
This way, ARM platforms no longer have to set their own values if
`ARM_BOARD_OPTIMISE_MEM=0` and they can specify optimized values
otherwise. The common sizes have been set to the highest values used
for any of the current build configurations.
This is needed because in some build configurations some images are
running out of space. This way there is a common set of values known
to work for all of them and it can be optimized for each particular
platform if needed.
The space reserved for BL2 when `TRUSTED_BOARD_BOOT=0` has been
increased. This is needed because when memory optimisations are
disabled the values for Juno of `PLAT_ARM_MMAP_ENTRIES` and
`MAX_XLAT_TABLES` are higher. If in this situation the code is
compiled in debug mode and with "-O0", the code won't fit.
Change-Id: I70a3d8d3a0b0cad1d6b602c01a7ea334776e718e
This patch reworks type usage in generic code, drivers and ARM platform files
to make it more portable. The major changes done with respect to
type usage are as listed below:
* Use uintptr_t for storing address instead of uint64_t or unsigned long.
* Review usage of unsigned long as it can no longer be assumed to be 64 bit.
* Use u_register_t for register values whose width varies depending on
whether AArch64 or AArch32.
* Use generic C types where-ever possible.
In addition to the above changes, this patch also modifies format specifiers
in print invocations so that they are AArch64/AArch32 agnostic. Only files
related to upcoming feature development have been reworked.
Change-Id: I9f8c78347c5a52ba7027ff389791f1dad63ee5f8
On ARM CSS platforms, the whole flash used to be mapped as executable.
This is not required, given that the flash is used to store the BL1
and FIP images and:
- The FIP is not executed in place, its images are copied to RAM
and executed from there.
- BL1 is executed in place from flash but only its code needs to be
mapped as executable and platform code takes care of re-mapping
BL1's read-only section as executable.
Therefore, this patch now maps the flash as non-executable by default
on these platforms. This increases security by restricting the
executable region to what is strictly needed.
This patch also adds some comments to clarify the memory mapping
attributes on these platforms.
Change-Id: I4db3c145508bea1f43fbe0f6dcd551e1aec1ecd3
This patch introduces the arm_setup_page_tables() function to
set up page tables on ARM platforms. It replaces the
arm_configure_mmu_elx() functions and does the same thing except
that it doesn't enable the MMU at the end. The idea is to reduce
the amount of per-EL code that is generated by the C preprocessor
by splitting the memory regions definitions and page tables creation
(which is generic) from the MMU enablement (which is the only per-EL
configuration).
As a consequence, the call to the enable_mmu_elx() function has been
moved up into the plat_arch_setup() hook. Any other ARM standard
platforms that use the functions `arm_configure_mmu_elx()` must be
updated.
Change-Id: I6f12a20ce4e5187b3849a8574aac841a136de83d
Replaced placeholder implementation of plat_set_nv_ctr for FVP
platforms by a working one.
On FVP, the mapping of region DEVICE2 has been changed from RO to RW
to prevent exceptions when writing to the NV counter, which is
contained in this region.
Change-Id: I56a49631432ce13905572378cbdf106f69c82f57
This patch adds ARM Cortex-A73 MPCore Processor support
in the CPU specific operations framework. It also includes
this support for the Base FVP port.
Change-Id: I0e26b594f2ec1d28eb815db9810c682e3885716d
This patch adds support to select CCN driver for FVP during build.
A new build option `FVP_INTERCONNECT_DRIVER` is added to allow
selection between the CCI and CCN driver. Currently only the CCN-502
variant is supported on FVP.
The common ARM CCN platform helper file now verifies the cluster
count declared by platform is equal to the number of root node
masters exported by the ARM Standard platform.
Change-Id: I71d7b4785f8925ed499c153b2e9b9925fcefd57a
Added a build flag to select the generic delay timer on FVP instead
of the SP804 timer. By default, the generic one will be selected. The
user guide has been updated.
Change-Id: Ica34425c6d4ed95a187b529c612f6d3b26b78bc6
This patch changes the default driver for FVP platform from the deprecated
GICv3 legacy to the GICv3 only driver. This means that the default build of
Trusted Firmware will not be able boot Linux kernel with GICv2 FDT blob. The
user guide is also updated to reflect this change of default GIC driver for
FVP.
Change-Id: Id6fc8c1ac16ad633dabb3cd189b690415a047764
Sandrine Bailleux
Isla Mitchell
davidcunado-arm
dp-arm
danh-arm
Jeenu Viswambharan
David Wang
Masahiro Yamada
Douglas Raillard
Soby Mathew
Yatharth Kochar
Antonio Nino Diaz