Very rarely, during cpuidle operations the following error
is seen: "PM MSG Trigger Timeout".
This is caused by slow handling of message interrutps
in the PM FW running on CM3 (under heavy PM operation load).
This is not a real issue, so we extend the timeout to
avoid the error prints.
Change-Id: I92fd6f2ff1ddf208b216c123880ded28a00b6e0e
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/59670
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Add static configuration for SFI+ 10Gbps interface on SERDES
Lane 4.
This is just a copy of Lane 2 static values, not optimized.
Board-to-board iperf test shows up to 6Gbps transfer speed.
Change-Id: I024d2ac132f7fa6c342a64367f3dca2123a27e97
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Add description for memory layouts used by EspressoBin v7 (DDR4)
Change-Id: I199d8b52580b26e560f14b503a6e99d32de4f284
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/61279
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
- Number of open power switches for CPUs should be three
and now two.
- This patch updates the value of open power switches from
0xfd (two power-switches) to 0xfc (three power-switches).
Change-Id: I2783ab7f04bbbb6da78eeedcabe4636f9a774512
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Add support for SVC test builds for tuning AVS values.
Update the SVC procedure and add EEPROM access.
Add support for AP807 AVS values (10 bits wide).
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
- Update CPU frequency on AP807 to 2GHz for SAR 0x0.
- Increase AVS to 0.88V for 2GHz clock
Change-Id: Ic945b682ab2f8543e34294bfc56c3eae2c5e0c8e
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
In Armada 8K DB boards, PCIe initialization can be executed only once
because PCIe reset performed during chip power on and it cannot be
executed via GPIO later.
This means that power on can be executed only once, when it's called
from the bootloader.
Power on:
Read bit 21 of the mode, it marks if the caller is
the bootloader or the Linux Kernel.
Power off:
Check if the comphy was already configured to PCIe, if yes,
check if the caller is bootloader, if both conditions are true
(PCIe mode and called by Linux) - skip the power-off.
In addition, fix incorrect documentation describing mode fields -
PCIe width is 3 bits, not 2.
NOTE: with this patch, please use LK4.14.76 (LK4.4.120 may not work
with it).
Change-Id: I4b929011f97a0a1869a51ba378687e78b3eca4ff
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Do not power off the CPU1 since there is no way to wake it up
(wake-up is causing CPU0 reset as well duo to HW bug). Quote from errata
Ref #13 [In power saving mode, both cores must be powered off]:
"When Core 0 is on and Core 1 is in power-off state, a Core 1
wake-up resets Core 0 as well and puts Core 0 back to ROM".
To overcome described HW bug instead of powering the CPU off, let it
reach WFI instruction, which is invoked by generic psci_do_cpu_off
function after platform handler finishes. This will put the core in low
power state and give a chance to wake it up.
Before this change, after running secondary kernel via kexec, only one
core was up, now both cores are up.
Change-Id: I87f144867550728055d9b8a2edb84a14539acab7
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Secure world execution nearly always expect a controlled exit to
Non-secure world. SDEI interrupts, although targets EL3, occur on behalf
of Non-secure world, and may have higher priority than Secure world
interrupts. Therefore they might preempt Secure execution, and yield
execution to Non-secure SDEI handler. Upon completion of SDEI event
handling (regardless of whether it's COPLETE or COMPLETE_AND_RESUME), we
must resume Secure execution if it was preempted.
Change-Id: I6edd991032588588427ba2fe6c3d7668f7080e3d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The headers forked at some point in the past and have diverged a lot. In
order to make it easier to share code between TF-A-Tests and TF-A, this
patch synchronises most of the definitions in the mentioned headers.
This is not a complete sync, it has to be followed by more cleanup.
This patch also removes the read helpers for the AArch32 instructions
ats1cpr and ats1hr (they are write-only).
Change-Id: Id13ecd7aeb83bd2318cd47156d71a42f1c9f6ba2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch adds support to build a combined BL1
and ROMLIB binary file with the right page
alignment in Juno. When USE_ROMLIB=1 is set for
Juno, it generates the combined file
bl1_romlib.bin which needs to be used instead of
bl1.bin
Change-Id: I407efbe48d3e522fa6ef855538a9587193cb1919
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
Register functions have to be added to the
jump table to allow patching in the
future
Change-Id: I57a885f7fc6290ea74a6096aea5b1867b2098eb7
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
This change allows patching of functions in the
romlib. This can be done by adding "patch" at the
end of the jump table entry for the function that
needs to be patched in the file jmptbl.i.
Functions patched in the jump table list will be
built as part of the BL image and the romlib
version will not be used
Change-Id: Iefb200cb86e2a4b61ad3ee6180d3ecc39bad537f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
This reverts commit 6f512a3dfd.
According to the 'Cortex-A57 MPCore Software Developers Errata Notice':
This bug will only affect secure AArch64 EL3. If the above
conditions occur, the CPU will not invalidate the targeted EL3 TLB
entries and incorrect translations might occur.
For this reason it is not needed in AArch32.
Change-Id: I6f7b333817515499723e8f306145790ad6af9975
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Provide new APIs to add new regions without specifying the base VA.
- `mmap_add_region_alloc_va` adds a static region to mmap choosing as
base VA the first possible address after all the currently mapped
regions. It is aligned to an appropriate boundary in relation to the
size and base PA of the requested region. No attempt is made to fill
any unused VA holes.
- `mmap_add_dynamic_region_alloc_va` it adds a region the same way as
`mmap_add_region_alloc_va` does, but it's dynamic instead of static.
- `mmap_add_alloc_va` takes an array of non const `mmap_region_t`,
maps them in the same way as `mmap_add_region_alloc_va` and fills
their `base_va` field. A helper macro has been created to help create
the array, called `MAP_REGION_ALLOC_VA`.
Change-Id: I5ef3f82ca0dfd0013d2e8034aa22f13ca528ba37
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Remove the platform common plat_arm_security_setup function to allow
platform specific implementations of the security setup function
implemented in the board directory of the platform.
For use by secure software, configure region0 of DMC-620 trustzone
controller to protect the upper 16MB of memory of the first DRAM block
from non-secure accesses.
Change-Id: I9a8c19656702c4fa4f6917b3655b692d443bb568
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
ARM CoreLink DMC-620 Dynamic Memory Controller includes a TZC controller
to setup secure or non-secure regions of DRAM memory. The TZC controller
allows to setup upto eight such regions of memory in DRAM. This driver
provides helper functions to setup the TZC controller within DMC-620.
Change-Id: Iee7692417c2080052bdb7b1c2873a024bc5d1d10
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
RCAR_RPC_HYPERFLASH_LOCKED can be set to 0 as a build option if the
user needs to allow u-boot to reprogram the ATF firmware using a FIP
image (as a faster alternative of toggling numerous DIP switches on
the board and using ascii-xfer of srec files)
The code being controlled with this commit should only be re-enabled for
debugging (_never_ on a product release)
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
It's better to have them in a separate file instead of having them spread
across the Makefile. This is what the stack protector is already doing.
Change-Id: Id30742c0af10de5ea6d10674ca25bf52b0f2b262
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The default Raspberry Pi 3 memory mapping for ATF is geared towards
the use of uboot + Linux. This creates issues when trying to use
ATF with an UEFI payload and Windows on ARM64.
We therefore introduce new build option RPI3_USE_UEFI_MAP, that
enables the build process to use an alternate memory mapping that
is compatible with UEFI + Windows (as well as UEFI + Linux).
FixesARM-software/tf-issues#649
Signed-off-by: Pete Batard <pete@akeo.ie>
Migrate Marvell platforms from legacy console API to
multi-console API.
Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Now that MULTI_CONSOLE_API is enabled for the STM32MP1 platform,
we can remove the non MULTI_CONSOLE_API parts in the driver.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
When compiling assembly files, stdint.h is not included.
UINT32_C and UINT64_C are then not defined.
A new GENMASK macro for assembly is then created.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
According to "openssl" manual:
-K key
The actual key to use: this must be represented as a string
comprised only of hex digits. If only the key is specified,
the IV must additionally specified using the -iv option.
When both a key and a password are specified, the key given
with the -K option will be used and the IV generated from the
password will be taken.
It does not make much sense to specify both key and password.
This patch removes "-k 0" parameter from the encryption command
since we are already using "-K" and "-iv" for the key and IV.
Change-Id: Ia333cedaa3207e643c95d2ec7c229f50eeab96db
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/60745
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Sharon Habet <sharonh@marvell.com>
Konstantin Porotchkin
Igal Liberman
Christine Gharzuzi
Grzegorz Jaszczyk
Antonio Niño Díaz
Jeenu Viswambharan
Sathees Balya
Vijayenthiran Subramaniam
Pete Batard
Jorge Ramirez-Ortiz
Ryan Grachek
Yann Gautier