Register in the shared resources driver the secure or non-secure state
of the GPIO pins.
Change-Id: Ifda473bcbbb0af799be6587961d6641edf887605
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Register in the shared resources driver the secure or non-secure state
of the IWDG instances.
Change-Id: I3a3bc9525447f6a2a465891ca3a3fd5fe664ca07
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Register in the shared resources driver the secure or non-secure
state of the PMIC.
Change-Id: Ic1f172ba62785018f8e9bb321782d725e2d2f434
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Introduce stm32mp1_register_clock_parents_secure() in stm32mp1
clock driver to allow platform shared resources to register as
secure the parent clocks of a clock registered as secure.
Change-Id: I53a9ab6aa78ee840ededce67e7b12a84e08ee843
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
This change implements SCMI channels for reading a SCMI message from a
shared memory and call the SCMI message drivers to route the message
to the target platform services.
SMT refers to the shared memory management protocol which is used
to get/put message/response in shared memory. SMT is a 28byte header
stating shared memory state and exchanged protocol data.
The processing entry for a SCMI message can be a secure interrupt
or fastcall SMCCC invocation.
SMT description in this implementation is based on the OP-TEE
project [1] itself based in the SCP-firmware implementation [2].
Link: [1] a58c4d706d
Link: [2] https://github.com/ARM-software/SCP-firmware.git
Change-Id: I416c7dab5c67954c6fe80bae8d8cdfdcda66873e
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Adds SCMI reset domain protocol support in the SCMI message drivers
as defined in SCMI specification v2.0 [1]. Not all the messages
defined in the specification are supported.
scmi_msg_get_rd_handler() sanitizes the message_id value
against any speculative use of reset domain ID as a index since by
SCMI specification, IDs are indices.
This implementation is based on the OP-TEE project implementation [2]
itself based on the SCP-firmware implementation [3] of the SCMI
protocol server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] 56a1f10ed9
Link: [3] https://github.com/ARM-software/SCP-firmware.git
Change-Id: If7cf13de40a815dedb40dcd5af8b6bb6725d9078
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Adds SCMI clock protocol support in the SCMI message drivers as
defined in SCMI specification v2.0 [1] for clock protocol messages.
Platform can provide one of the plat_scmi_clock_*() handler for the
supported operations set/get state/rate and others.
scmi_msg_get_clock_handler() sanitizes the message_id value
against any speculative use of clock ID as a index since by
SCMI specification, IDs are indices.
This implementation is based on the OP-TEE project implementation [2]
itself based on the SCP-firmware implementation [3] of the SCMI
protocol server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] a7a9e3ba71
Link: [3] https://github.com/ARM-software/SCP-firmware.git
Change-Id: Ib56e096512042d4f7b9563d1e4181554eb8ed02c
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
This change introduces drivers to allow a platform to create a basic
SCMI service and register handlers for client request (SCMI agent) on
system resources. This is the first piece of the drivers: an entry
function, the SCMI base protocol support and helpers for create
the response message.
With this change, scmi_process_message() is the entry function to
process an incoming SCMI message. The function expect the message
is already copied from shared memory into secure memory. The message
structure stores message reference and output buffer reference where
response message shall be stored.
scmi_process_message() calls the SCMI protocol driver according to
the protocol ID in the message. The SCMI protocol driver will call
defined platform handlers according to the message content.
This change introduces only the SCMI base protocol as defined in
SCMI specification v2.0 [1]. Not all the messages defined
in the specification are supported.
The SCMI message implementation is derived from the OP-TEE project [2]
itself based on the SCP-firmware implementation [3] of the SCMI protocol
server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] ae8c806809
Link: [3] https://github.com/ARM-software/SCP-firmware/tree/v2.6.0
Change-Id: I639c4154a39fca60606264baf8d32452641f45e9
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
ETZPC stands for Extended TrustZone Protection Controller. It is a
resource conditional access device. It is mainly based on Arm TZPC.
ST ETZPC exposes memory mapped DECPROT cells to set access permissions
to SoC peripheral interfaces as I2C, SPI, DDR controllers, and some
of the SoC internal memories.
ST ETZPC exposes memory mapped TZMA cells to set access permissions
to some SoC internal memories.
Change-Id: I47ce20ffcfb55306dab923153b71e1bcbe2a5570
Co-developed-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Changes stm32mp1 reset driver to API to add a timeout argument
to stm32mp_reset_assert() and stm32mp_reset_deassert() and
a return value.
With a supplied timeout, the functions wait the target reset state
is reached before returning. With a timeout of zero, the functions
simply load target reset state in SoC interface and return without
waiting.
Helper functions stm32mp_reset_set() and stm32mp_reset_release()
use a zero timeout and return without a return code.
This change updates few stm32 drivers and plat/stm32mp1 blé_plat_setup.c
accordingly without any functional change.
functional change.
Change-Id: Ia1a73a15125d3055fd8739c125b70bcb9562c27f
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Adds missing terminal new line character '\n' to debug traces,
fix format as index is an unsigned value and use present tense rather
than past tense in the printed message.
Change-Id: I88c06ef4d3a11d97ff8e96875a3dd0f58a3c98b6
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Enable few system clocks at related BL initialization.
Change-Id: I12b35e8cdc128b993de4a1dc4c6e9d52624dd8d9
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Oscillators and PLLs are not gated on stm32mp_clk_enable/disable()
calls. This change prevents functions to panic when called for such
always-on clocks. Gating these clocks is out of the scope of
this change.
Change-Id: Ie730553dea480b529de942446176db9119587832
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Adds RTC clock to the list of the supported clocks. This allows
stm32mp_clk_*() API functions to enable, disable and set and get
rate for the clock RTC clock.
Change-Id: I8efc3f00b1f22d1912f59d1846994e9e646d6614
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
The current implementation optimizes memory consumed by gateable
clock table by storing bit mask and bit shift with 1 byte each.
The issue is that register selector bit masks above the 7th LSBit
cannot be stored.
This change uses the shift info to shift the mask before it is used,
allowing clock selector register bit fields to be spread on the 32 bits
of the register as long as the mask fits in 8 contiguous bit at most.
This change is needed to add the RTC clock to the gateable clocks table.
Change-Id: I8a0fbcbf20ea383fb3d712f5064d2d307e44465d
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Oscillators, PLLs and some system clocks can be related straight to
a parent clock. Prior this change were only oscillators and few
clocks supported by this look up. This changes adds PLLs and other
system clocks. This enables for flexible use of clock tree exploration
when computing a clock frequency value.
Change-Id: I15ec98023a7095e3120a6954de59a4799d92c66b
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
The STM32 platform port parse DT nodes to find base address to
peripherals. It does this by using its own implementation, even though
this functionality is generic and actually widely useful outside of the
STM32 code.
Re-implement fdt_get_reg_props_by_name() on top of the newly introduced
fdt_get_reg_props_by_index() function, and move it to fdt_wrapper.c.
This is removes the assumption that #address-cells and #size-cells are
always one.
Change-Id: I6d584930262c732b6e0356d98aea50b2654f789d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The STM32 platform code uses its own set of FDT helper functions,
although some of them are fairly generic.
Remove the implementation of fdt_read_uint32_default() and implement it
on top of the newly introduced fdt_read_uint32() function, then convert
all users over.
This also fixes two callers, which were slightly abusing the "default"
semantic.
Change-Id: I570533362b4846e58dd797a92347de3e0e5abb75
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The device tree parsing code for the STM32 platform is using its own FDT
helper functions, some of them being rather generic.
In particular the existing fdt_read_uint32_array() implementation is now
almost identical to the new generic code in fdt_wrappers.c, so we can
remove the ST specific version and adjust the existing callers.
Compared to the original ST implementation the new version takes a
pointer to the DTB as the first argument, and also swaps the order of
the number of cells and the pointer.
Change-Id: Id06b0f1ba4db1ad1f733be40e82c34f46638551a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
A speculative accesses to DDR could be done whereas it was not reachable
and could lead to bus stall.
To correct this the dynamic mapping in MMU is used.
A first mapping is done for DDR tests with MT_NON_CACHEABLE attribute,
once DDR access is setup. It is then unmapped and a new mapping DDR is done
with cacheable attribute (through MT_MEMORY) to speed-up BL33 (or OP-TEE)
load.
The disabling of cache during DDR tests is also removed, as now useless.
A call to new functions stm32mp_{,un}map_ddr_non_cacheable() is done
instead.
PLAT_XLAT_TABLES_DYNAMIC is activated globally as used in BL2 and BL32.
BL33 max size is also updated to take into account the secure and shared
memory areas. Those are used in OP-TEE case.
Change-Id: I22c48b4a48255ee264991c34ecbb15bfe87e67c3
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This issue was found with cppcheck in our downstream code:
[drivers/st/io/io_stm32image.c:234] -> [drivers/st/io/io_stm32image.c:244]:
(warning) Either the condition 'buffer!=0U' is redundant or there is
possible null pointer dereference: local_buffer.
Change-Id: Ieb615b7e485dc93bbeeed4cd8bf845eb84c14ac9
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The variable is wrongly set to 0L, whereas it is an unsigned int, it should
then be 0U.
Change-Id: I0b164c0ea598ec8a503f1693da2f3789f59da238
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Sparse issue:
drivers/st/spi/stm32_qspi.c:445:5:
warning: symbol 'stm32_qspi_init' was not declared. Should it be static?
Cppcheck issue:
[drivers/st/spi/stm32_qspi.c:175] -> [drivers/st/spi/stm32_qspi.c:187]:
(style) Variable 'len' is reassigned a value before the old one has been
used.
[drivers/st/spi/stm32_qspi.c:178]:
(style) The scope of the variable 'timeout' can be reduced.
Change-Id: I575fb50766355a6717cbd193fc4a80ff1923014c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: Iea6ca26ff4903c33f0fad27fec96fdbabd4e0a91
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
IO seek offset can be set to values above UINT32_MAX, this change
changes the seek offset argument from 'ssize_t' to 'signed long long'.
Fixing platform seek functions to match the new interface update.
Change-Id: I25de83b3b7abe5f52a7b0fee36f71e60cac9cfcb
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I84f8a99be2dcdf7c51fbecdb324df8e2f32cc855
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This commit adds authentication binary support for STM32MP1.
It prints the bootrom authentication result if signed
image is used and authenticates the next loaded STM32 images.
It also enables the dynamic translation table support
(PLAT_XLAT_TABLES_DYNAMIC) to use bootrom services.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Iba706519e0dc6b6fae1f3dd498383351f0f75f51
This BSEC service is a platform specific service. Implementation
moved to the platform part.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I1f70ed48a446860498ed111acce01187568538c9
The driver manages the HASH processor IP on STM32MP1
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I3b67c80c16d819f86b951dae29a6c465e51ad585
The STM32 console driver was pre-pending '\r' before '\n'.
It is now managed by the framework with the flag:
CONSOLE_FLAG_TRANSLATE_CRLF.
Remove the code in driver, and add the flag for STM32MP1.
Change-Id: I5d0d5d5c4abee0b7dc11c2f8707b1b5cf10149ab
Signed-off-by: Yann Gautier <yann.gautier@st.com>
DBLOCKSIZE should be filled such as the data size is 2^DBLOCKSIZE.
Hence it is calculated with __builtin_ctz.
Change-Id: Id6b5ff9b594afc4fc523a388011beed307e6abd1
Signed-off-by: Yann Gautier <yann.gautier@st.com>
If the max-frequency property is provided in the device tree mmc node,
it should be managed. The max allowed frequency will be the min between
this property value and what the card can support.
Change-Id: I885b676c3300d2670a0fe4c6ecab87758b5893ad
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This function can be used on several stm32mp devices, it is then moved in
plat/st/common/stm32mp_common.c.
Change-Id: I862debe39604410f71a9ddc28713026362e9ecda
Signed-off-by: Yann Gautier <yann.gautier@st.com>
To use spinlocks, MMU should be enabled, as well as data cache.
A common function is created (moved from clock file).
It is then used whenever a spinlock has to be taken, in BSEC and clock
drivers.
Change-Id: I94baed0114a2061ad71bd5287a91bf7f1c6821f6
Signed-off-by: Yann Gautier <yann.gautier@st.com>
In order to correctly manage the bring-up of non boot CPUs, the RTCAPB
clock needs to be enabled.
It controls the access to backup registers, where the CPU entrypoint
will be stored.
Change-Id: Ifeeceb4faf64bc9e0778030444f437cc0bb27272
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Introduce driver for STM32 IWDG peripheral (Independent Watchdog).
It is configured according to device tree content and should be enabled
from there.
The watchdog is not started by default. It can be started after an HW
reset if the dedicated OTP is fused.
The watchdog also needs to be frozen if a debugger is attached.
This is done by configuring the correct bits in DBGMCU.
This configuration is allowed by checking BSEC properties.
An increase of BL2 size is also required when adding this new code.
Change-Id: Ide7535d717885ce2f9c387cf17afd8b5607f3e7f
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
The system configuration controller is mainly used to manage
the compensation cell and other IOs and system related settings.
The SYSCFG driver is in charge of configuring masters on the interconnect,
IO compensation, low voltage boards, or pull-ups for boot pins.
All other configurations should be handled in Linux drivers requiring it.
Device tree files are also updated to manage vdd-supply regulator.
Change-Id: I10fb513761a7d1f2b7afedca9c723ad9d1bccf42
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
To activate the CSG option, the driver needs to set the bit2
of PLLNCR register = SSCG_CTRL: Spread Spectrum Clock Generator.
This bit should not be cleared when starting the PLL.
Change-Id: Ie5c720ff03655f27a7e7e9e7ccf8295dd046112f
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Rework the macro that eases the table definition: the src and msk fields
are now using MASK and SHIFT defines of each source register.
Some macros had then to be modified: _USART1_SEL, _ASS_SEL and _MSS_SEL to
_UART1_SEL, _AXIS_SEL, and _MCUS_SEL to match register fields.
Note: the mask for RCC_ASSCKSELR_AXISSRC is changed from 0x3 to 0x7
to reflect the size of the register field, even if there are only
3 possible clock sources.
The mask value is also corrected for QSPI and FMC clock selection.
Change-Id: I44114e3c1dd37b9fa1be1ba519611abd9a07764c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Those functions are generic for parsing nodes from device tree
hence could be located in generic source file.
The oscillators description structure is also moved to STM32MP1 clock
driver, as it is no more used in stm32mp1_clkfunc and cannot be in a
generic file.
Change-Id: I93ba74f4eea916440fef9b160d306af1b39f17c6
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Those defines are used in STM32MP1 clock driver.
It is better to put them altogether with already defined registers.
Change-Id: I6f8ad8c2477b947af6f76283a4ef5c40212d0027
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The old version of the macro is deprecated.
Commit cc5859ca19 ("Multi-console: Deprecate the
`finish_console_register` macro") provides more details.
Change-Id: I3d1cdf6496db7d8e6cfbb5804f508ff46ae7e67e
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
STM32MP1 SDMMC device voltage is 3.3V. We should then precise the 2 ranges
3.2 to 3.3V and 3.3 to 3.4V in ocr_voltage field.
Change-Id: I88e479f8f16bfe608a7808eace0df3fdec48deab
Signed-off-by: Yann Gautier <yann.gautier@st.com>
STM32MP1 chip embeds a dual Cortex-A7 and a Cortex-M4.
The support for Cortex-M4 clocks is added when configuring the clock tree.
Some minimal security features to allow communications between A7 and M4
are also added.
Change-Id: I60417e244a476f60a2758f4969700b2684056665
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Remove useless private structure in function prototypes.
Add a reference counter on clocks.
Prepare for future secured/shared/non-secured clocks.
Change-Id: I3dbed81721da5ceff5e10b2c4155b1e340c036ee
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
This change makes the platform to panic in case of peripheral reset
resource malfunction.
Change-Id: I17eb9cb045b78a4e5142a8c33b744e84992d732a
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
PWR, RCC, DDRPHYC & DDRCTRL addresses can be retrieved from device tree.
Platform asserts the value read from the DT are the SoC addresses.
Change-Id: I43f0890b51918a30c87ac067d3780ab27a0f59de
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
Create a new file stm32mp_clkfunc.c to put functions that could be common
between several platforms.
Change-Id: Ica915c796b162b2345056b33328acc05035a242c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Regulator configuration at boot takes more information from DT.
I2C configuration from DT is done in I2C driver.
I2C driver manages more transfer modes.
The min voltage of buck1 should also be increased to 1.2V,
else the platform does not boot.
Heavily modifies stm32_i2c.c since many functions move inside the source
file to remove redundant declarations.
Change-Id: I0bee5d776cf3ff15e687427cd6abc06ab237d025
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
Remove the previously use function: get_timer, and use new functions
timeout_init_us and timeout_elapsed.
Change-Id: I4e95b123648bff7ca91e40462a2a3ae24cfe1697
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
Include all RCC, clocks and reset headers from stm32mp1_def.h
which if exported to the firmware through platform_def.h.
The same dependency removal is done in common code as well.
Some useless includes are also removed in stm32_sdmmc2 driver.
Change-Id: I731ea5775c3fdb7f7b0c388b93923ed5e84b8d3f
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Mainly remove suffix 1 from prefix stm32mp1 in several macros and functions
that can be used in drivers shared by different platforms.
Change-Id: I2295c44f5b1edac7e80a93c0e8dfd671b36e88e7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Some parts of code could be shared with platform derivatives,
or new platforms.
A new folder plat/st/common is created to put common parts.
stm32mp_common.h is a common API aggregate.
Remove some casts where applicable.
Fix some types where applicable.
Remove also some platform includes that are already in stm32mp1_def.h.
Change-Id: I46d763c8d9e15732d1ee7383207fd58206d7f583
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
The BSEC (Boot and Security and OTP control) is intended to control an OTP
(one time programmable) fuse box, used for on-chip non-volatile storage
for device configuration and security parameters.
Change-Id: I38c44684c7b9c6a1f24ec0ae3fe99cec481d5a51
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Change fdt_check_status function to fdt_get_status.
Update GPIO defines.
Move some functions in gpio driver, instead of dt helper file.
Add GPIO bank helper functions.
Use only one status field in dt_node_info structure including both status
and secure status.
Change-Id: I34f93408dd4aac16ae722f564bc3f7d6ae978cf4
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Reword some traces.
Use uintptr_t where required.
Reduce scope of variables.
Improve io_stm32image algo.
Complete some IP registers definitions.
Add failure on supported DDR (stm32mp1_ddr_init()).
Fix cache flush on cache disable (stm32mp1_ddr_setup).
Change-Id: Ie02fa71e02b9d69abc807fd5b7df233e5be6668c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Change-Id: I4a1b281925e0a3a1e2a34b3e363537e4a7f13823
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
The drivers are also updated to reflect the changes.
Set RCC as non-secure.
Change-Id: I568fa1f418355830ad1d4d1cdcdb910fb362231b
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This is the correct name of the IP.
Rename stm32mp1_pmic files to stm32mp_pmic.
Change-Id: I238a7d1f9a1d099daf7788dc9ebbd3146ba2f15f
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The driver could be used for other devices than PMIC.
Change-Id: I4569e7c0028e52e1ff2fe9d38f11de11e95d1897
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Instead, only platform_def.h is included.
The required files to be included are added in stm32mp1_def.h.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Now that MULTI_CONSOLE_API is enabled for the STM32MP1 platform,
we can remove the non MULTI_CONSOLE_API parts in the driver.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
These issues wer found by sparse:
drivers/st/clk/stm32mp1_clk.c:1524:19:
warning: incorrect type in assignment (different base types)
expected restricted fdt32_t const [usertype] *pkcs_cell
got unsigned int const [usertype] *
plat/st/stm32mp1/plat_image_load.c:13:6:
warning: symbol 'plat_flush_next_bl_params' was not declared.
Should it be static?
plat/st/stm32mp1/plat_image_load.c:21:16:
warning: symbol 'plat_get_bl_image_load_info' was not declared.
Should it be static?
plat/st/stm32mp1/plat_image_load.c:29:13:
warning: symbol 'plat_get_next_bl_params' was not declared.
Should it be static?
plat/st/stm32mp1/bl2_io_storage.c:40:10:
warning: symbol 'block_buffer' was not declared. Should it be static?
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Whereas the GPT table is read with io_block, the binaries to be loaded
(e.g. BL33) cannot use it, as it is not suitable to read them block by
block, or the boot time would be very bad.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This IO is required to read binaries with STM32 header.
This header is added with the stm32image tool.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This driver is for the STMicroelectronics sdmmc2 IP
which is in STM32MP1 SoC.
It uses the MMC framework, and can address either eMMC or SD-card.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
tf_printf and tf_snprintf are now called printf and snprintf, so the
code needs to be updated.
Change-Id: Iffeee97afcd6328c4c2d30830d4923b964682d71
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Functions provided by stdio.h such as printf and sprintf are available
in the codebase, but they add a lot of code to the final image if they
are used:
- AArch64: ~4KB
- AArch32: ~2KB in T32, ~3KB in A32
tf_printf and tf_snprintf are a lot more simple, but it is preferable
to use them when possible because they are also used in common code.
Change-Id: Id09fd2b486198fe3d79276e2c27931595b7ba60e
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The DDR driver is under dual license, BSD and GPLv2.
The configuration parameters are taken from device tree.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
If a PMIC companion chip is present on board, it has to be configured
for regulators supplies.
This check is done with board DT configuration.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
The management of pinctrl nodes of device tree is also added.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
The clock driver is under dual license, BSD and GPLv2.
The clock driver uses device tree, so a minimal support for this is added.
The required files for driver and DTS files are in include/dt-bindings/.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
STM32MP1 is a microprocessor designed by STMicroelectronics,
based on a dual Arm Cortex-A7.
It is an Armv7-A platform, using dedicated code from TF-A.
STM32MP1 uses BL2 compiled with BL2_AT_EL3.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Etienne Carriere
Etienne Carriere
Mark Dykes
Andre Przywara
Yann Gautier
Lionel Debieve
Nicolas Le Bayon
Ambroise Vincent
Antonio Nino Diaz