This patch adds a device driver which can be used to program the following
aspects of ARM CCN IP:
1. Specify the mapping between ACE/ACELite/ACELite+DVM/CHI master interfaces and
Request nodes.
2. Add and remove master interfaces from the snoop and dvm
domains.
3. Place the L3 cache in a given power state.
4. Configuring system adress map and enabling 3 SN striping mode of memory
controller operation.
Change-Id: I0f665c6a306938e5b66f6a92f8549b529aa8f325
Currently, the non-overlapping video memory carveout region is cleared after
disabling the MMU at EL3. If at any exception level the carveout region is being
marked as cacheable, this zeroing of memory will not have an affect on the
cached lines. Hence, we first invalidate the dirty lines and update the memory
and invalidate again so that both caches and memory is zeroed out.
Change-Id: If3b2d139ab7227f6799c0911d59e079849dc86aa
This patch corrects the watchdog register setting. To update watchdog
register, the watchdog mode key must be set to make the register
configurable.
Change-Id: I9ca98ea4012f7f220b116013461030de4638ce0b
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>
This patch update Mediatek port to use the `DEFINE_BAKERY_LOCK` macro instead of
specifying the exact data structure to use for a bakery lock and the input
linker section that it should be allocated to.
Change-Id: I2116dbe27010bb46d7cc64fafef55c7240c4c721
Currently, on ARM platforms(ex. Juno) non-secure access to specific
peripheral regions, config registers which are inside and outside CSS
is done in the soc_css_security_setup(). This patch separates the CSS
security setup from the SOC security setup in the css_security_setup().
The CSS security setup involves programming of the internal NIC to
provide access to regions inside the CSS. This is needed only in
Juno, hence Juno implements it in its board files as css_init_nic400().
Change-Id: I95a1fb9f13f9b18fa8e915eb4ae2f15264f1b060
On Juno and FVP platforms, the Non-Secure System timer corresponds
to frame 1. However, this is a platform-specific decision and it
shouldn't be hard-coded. Hence, this patch introduces
PLAT_ARM_NSTIMER_FRAME_ID which should be used by all ARM platforms
to specify the correct non-secure timer frame.
Change-Id: I6c3a905d7d89200a2f58c20ce5d1e1d166832bba
This patch replaces the `ARM_TZC_BASE` constant with `PLAT_ARM_TZC_BASE` to
support different TrustZone Controller base addresses across ARM platforms.
Change-Id: Ie4e1c7600fd7a5875323c7cc35e067de0c6ef6dd
ARM TF configures all interrupts as non-secure except those which
are present in irq_sec_array. This patch updates the irq_sec_array
with the missing secure interrupts for ARM platforms.
It also updates the documentation to be inline with the latest
implementation.
FixesARM-software/tf-issues#312
Change-Id: I39956c56a319086e3929d1fa89030b4ec4b01fcc
The previous logic in the memctrl driver was not catering to cases
where the new memory region lied inside the older region. This patch
fixes the if/elseif/elseif logic in the driver to take care of this
case.
Reported by: Vikram Kanigiri <vikram.kanigiri@arm.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch programs the CPUECTLR_EL1 and L2ECTLR_EL1 registers,
so that the core waits for 512 generic timer CNTVALUEB ticks before
entering retention state, after executing a WFI instruction.
This functionality is configurable and can be enabled for platforms
by setting the newly defined 'ENABLE_L2_DYNAMIC_RETENTION' and
'ENABLE_CPU_DYNAMIC_RETENTION' flag.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Use constant macro defined in platform_def.h to replace hardcoded value.
This patch fix following assert in new psci-1.0 framework.
ASSERT: populate_power_domain_tree <183> : j == PLATFORM_CORE_COUNT
Change-Id: I9b7eda525479464a8c3805b6fe14ffb10debaf72
Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>
1. SEJ should not be one of the wake up sources
BUG=chrome-os-partner:38426
TEST=powerd_dbus_suspend
Change-Id: If8f3f19a885e66d7c10b472c2e3182a5affa4773
Signed-off-by: kenny liang <kenny.liang@mediatek.com>
This patch adds the necessary documentation updates to porting_guide.md
for the changes in the platform interface mandated as a result of the new
PSCI Topology and power state management frameworks. It also adds a
new document `platform-migration-guide.md` to aid the migration of existing
platform ports to the new API.
The patch fixes the implementation and callers of
plat_is_my_cpu_primary() to use w0 as the return parameter as implied by
the function signature rather than x0 which was used previously.
Change-Id: Ic11e73019188c8ba2bd64c47e1729ff5acdcdd5b
This patch implements the platform power managment handler to verify
non secure entrypoint for ARM platforms. The handler ensures that the
entry point specified by the normal world during CPU_SUSPEND, CPU_ON
or SYSTEM_SUSPEND PSCI API is a valid address within the non secure
DRAM.
Change-Id: I4795452df99f67a24682b22f0e0967175c1de429
Now that the FVP mailbox is no longer zeroed, the function
platform_mem_init() does nothing both on FVP and on Juno. Therefore,
this patch pools it as the default implementation on ARM platforms.
Change-Id: I007220f4531f15e8b602c3368a1129a5e3a38d91
Since there is a unique warm reset entry point, the FVP and Juno
port can use a single mailbox instead of maintaining one per core.
The mailbox gets programmed only once when plat_setup_psci_ops()
is invoked during PSCI initialization. This means mailbox is not
zeroed out during wakeup.
Change-Id: Ieba032a90b43650f970f197340ebb0ce5548d432
This patch adds support to the Juno and FVP ports for composite power states
with both the original and extended state-id power-state formats. Both the
platform ports use the recommended state-id encoding as specified in
Section 6.5 of the PSCI specification (ARM DEN 0022C). The platform build flag
ARM_RECOM_STATE_ID_ENC is used to include this support.
By default, to maintain backwards compatibility, the original power state
parameter format is used and the state-id field is expected to be zero.
Change-Id: Ie721b961957eaecaca5bf417a30952fe0627ef10
This patch migrates ARM reference platforms, Juno and FVP, to the new platform
API mandated by the new PSCI power domain topology and composite power state
frameworks. The platform specific makefiles now exports the build flag
ENABLE_PLAT_COMPAT=0 to disable the platform compatibility layer.
Change-Id: I3040ed7cce446fc66facaee9c67cb54a8cd7ca29
This patch defines deprecated platform APIs to enable Trusted
Firmware components like Secure Payload and their dispatchers(SPD)
to continue to build and run when platform compatibility is disabled.
This decouples the migration of platform ports to the new platform API
from SPD and enables them to be migrated independently. The deprecated
platform APIs defined in this patch are : platform_get_core_pos(),
platform_get_stack() and platform_set_stack().
The patch also deprecates MPIDR based context management helpers like
cm_get_context_by_mpidr(), cm_set_context_by_mpidr() and cm_init_context().
A mechanism to deprecate APIs and identify callers of these APIs during
build is introduced, which is controlled by the build flag WARN_DEPRECATED.
If WARN_DEPRECATED is defined to 1, the users of the deprecated APIs will be
flagged either as a link error for assembly files or compile time warning
for C files during build.
Change-Id: Ib72c7d5dc956e1a74d2294a939205b200f055613
This commit does the switch to the new PSCI framework implementation replacing
the existing files in PSCI folder with the ones in PSCI1.0 folder. The
corresponding makefiles are modified as required for the new implementation.
The platform.h header file is also is switched to the new one
as required by the new frameworks. The build flag ENABLE_PLAT_COMPAT defaults
to 1 to enable compatibility layer which let the existing platform ports to
continue to build and run with minimal changes.
The default weak implementation of platform_get_core_pos() is now removed from
platform_helpers.S and is provided by the compatibility layer.
Note: The Secure Payloads and their dispatchers still use the old platform
and framework APIs and hence it is expected that the ENABLE_PLAT_COMPAT build
flag will remain enabled in subsequent patch. The compatibility for SPDs using
the older APIs on platforms migrated to the new APIs will be added in the
following patch.
Change-Id: I18c51b3a085b564aa05fdd98d11c9f3335712719
The new PSCI topology framework and PSCI extended State framework introduces
a breaking change in the platform port APIs. To ease the migration of the
platform ports to the new porting interface, a compatibility layer is
introduced which essentially defines the new platform API in terms of the
old API. The old PSCI helpers to retrieve the power-state, its associated
fields and the highest coordinated physical OFF affinity level of a core
are also implemented for compatibility. This allows the existing
platform ports to work with the new PSCI framework without significant
rework. This layer will be enabled by default once the switch to the new
PSCI framework is done and is controlled by the build flag ENABLE_PLAT_COMPAT.
Change-Id: I4b17cac3a4f3375910a36dba6b03d8f1700d07e3
The state-id field in the power-state parameter of a CPU_SUSPEND call can be
used to describe composite power states specific to a platform. The current PSCI
implementation does not interpret the state-id field. It relies on the target
power level and the state type fields in the power-state parameter to perform
state coordination and power management operations. The framework introduced
in this patch allows the PSCI implementation to intepret generic global states
like RUN, RETENTION or OFF from the State-ID to make global state coordination
decisions and reduce the complexity of platform ports. It adds support to
involve the platform in state coordination which facilitates the use of
composite power states and improves the support for entering standby states
at multiple power domains.
The patch also includes support for extended state-id format for the power
state parameter as specified by PSCIv1.0.
The PSCI implementation now defines a generic representation of the power-state
parameter. It depends on the platform port to convert the power-state parameter
(possibly encoding a composite power state) passed in a CPU_SUSPEND call to this
representation via the `validate_power_state()` plat_psci_ops handler. It is an
array where each index corresponds to a power level. Each entry contains the
local power state the power domain at that power level could enter.
The meaning of the local power state values is platform defined, and may vary
between levels in a single platform. The PSCI implementation constrains the
values only so that it can classify the state as RUN, RETENTION or OFF as
required by the specification:
* zero means RUN
* all OFF state values at all levels must be higher than all RETENTION
state values at all levels
* the platform provides PLAT_MAX_RET_STATE and PLAT_MAX_OFF_STATE values
to the framework
The platform also must define the macros PLAT_MAX_RET_STATE and
PLAT_MAX_OFF_STATE which lets the PSCI implementation find out which power
domains have been requested to enter a retention or power down state. The PSCI
implementation does not interpret the local power states defined by the
platform. The only constraint is that the PLAT_MAX_RET_STATE <
PLAT_MAX_OFF_STATE.
For a power domain tree, the generic implementation maintains an array of local
power states. These are the states requested for each power domain by all the
cores contained within the domain. During a request to place multiple power
domains in a low power state, the platform is passed an array of requested
power-states for each power domain through the plat_get_target_pwr_state()
API. It coordinates amongst these states to determine a target local power
state for the power domain. A default weak implementation of this API is
provided in the platform layer which returns the minimum of the requested
power-states back to the PSCI state coordination.
Finally, the plat_psci_ops power management handlers are passed the target
local power states for each affected power domain using the generic
representation described above. The platform executes operations specific to
these target states.
The platform power management handler for placing a power domain in a standby
state (plat_pm_ops_t.pwr_domain_standby()) is now only used as a fast path for
placing a core power domain into a standby or retention state should now be
used to only place the core power domain in a standby or retention state.
The extended state-id power state format can be enabled by setting the
build flag PSCI_EXTENDED_STATE_ID=1 and it is disabled by default.
Change-Id: I9d4123d97e179529802c1f589baaa4101759d80c
This patch introduces new platform APIs and context management helper APIs
to support the new topology framework based on linear core position. This
framework will be introduced in the follwoing patch and it removes the
assumption that the MPIDR based affinity levels map directly to levels
in a power domain tree. The new platforms APIs and context management
helpers based on core position are as described below:
* plat_my_core_pos() and plat_core_pos_by_mpidr()
These 2 new mandatory platform APIs are meant to replace the existing
'platform_get_core_pos()' API. The 'plat_my_core_pos()' API returns the
linear index of the calling core and 'plat_core_pos_by_mpidr()' returns
the linear index of a core specified by its MPIDR. The latter API will also
validate the MPIDR passed as an argument and will return an error code (-1)
if an invalid MPIDR is passed as the argument. This enables the caller to
safely convert an MPIDR of another core to its linear index without querying
the PSCI topology tree e.g. during a call to PSCI CPU_ON.
Since the 'plat_core_pos_by_mpidr()' API verifies an MPIDR, which is always
platform specific, it is no longer possible to maintain a default implementation
of this API. Also it might not be possible for a platform port to verify an
MPIDR before the C runtime has been setup or the topology has been initialized.
This would prevent 'plat_core_pos_by_mpidr()' from being callable prior to
topology setup. As a result, the generic Trusted Firmware code does not call
this API before the topology setup has been done.
The 'plat_my_core_pos' API should be able to run without a C runtime.
Since this API needs to return a core position which is equal to the one
returned by 'plat_core_pos_by_mpidr()' API for the corresponding MPIDR,
this too cannot have default implementation and is a mandatory API for
platform ports. These APIs will be implemented by the ARM reference platform
ports later in the patch stack.
* plat_get_my_stack() and plat_set_my_stack()
These APIs are the stack management APIs which set/return stack addresses
appropriate for the calling core. These replace the 'platform_get_stack()' and
'platform_set_stack()' APIs. A default weak MP version and a global UP version
of these APIs are provided for the platforms.
* Context management helpers based on linear core position
A set of new context management(CM) helpers viz cm_get_context_by_index(),
cm_set_context_by_index(), cm_init_my_context() and cm_init_context_by_index()
are defined which are meant to replace the old helpers which took MPIDR
as argument. The old CM helpers are implemented based on the new helpers to
allow for code consolidation and will be deprecated once the switch to the new
framework is done.
Change-Id: I89758632b370c2812973a4b2efdd9b81a41f9b69
On Tegra SoCs, the TZDRAM contains the BL31 and BL32 images. This patch
uses only the actual memory available for BL31 instead of mapping the
entire TZDRAM.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
The TZDRAM base on the reference platform has been bumped up due to
some BL2 memory cleanup. Platforms can also use a different TZDRAM
base by setting TZDRAM_BASE=<value> in the build command line.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch removes the bootargs pointer from the platform params
structure. Instead the bootargs are passed by the BL2 in the
bl32_ep_info struct which is a part of the EL3 params struct.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
The Memory Select Switch Controller routes any CPU transactions to
the appropriate slave depending on the transaction address. During
system suspend, it loses all config settings and hence the CPU has
to restore them during resume.
This patch restores the controller's settings for enabling WRAP to
INCR burst type conversions on the master ports, for any incoming
requests from the AXI slave ports.
Tested by performing multiple system suspend cycles.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch modifies the 'BUILD_PLAT' makefile variable to point to the soc
specific build directory in order to allow each Tegra soc to have its own
build directory. This way we can keep the build outputs separate and can
keep multiple soc specific builds alive at the same time.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch implements support for T132 (Denver CPU) based Tegra
platforms.
The following features have been added:
* SiP calls to switch T132 CPU's AARCH mode
* Complete PSCI support, including 'System Suspend'
* Platform specific MMIO settings
* Locking of CPU vector registers
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
The validate_power_state() handler checks the power_state for a valid afflvl
and state id. Although the afflvl check is common, the state ids are implementation
defined.
This patch moves the handler to the tegra/soc folder to allow each SoC to validate
the power_state for supported parameters.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch moves the inclusion of CPU code (A53, A57) to T210's
makefile. This way we can reduce code size for Tegra platforms by
including only the required CPU files.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
A new config, ENABLE_NS_L2_CPUECTRL_RW_ACCESS, allows Tegra platforms to
enable read/write access to the L2 and CPUECTRL registers. T210 is the
only platform that needs to enable this config for now.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch locks access to the PMC registers which hold the CPU reset
vector addresses. The PMC registers are used by the warmboot code and
must be locked during boot/resume to avoid booting into custom firmware
installed by unknown parties e.g. hackers.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
The PMC Scratch22 register contains the CPU reset vector to
be used by the warmboot code to power up the CPU while resuming
from system suspend. This patch locks this PMC register to avoid
any further writes.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch checks if the target CPU is already online before
proceeding with it's power ON sequence.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch de-asserts the CPU reset signals for each CPU as
part of it's power on sequence. This is needed to get rid of
the wait in BPMP firmware during SC7 exit.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch fixes the delay loop used to wake up the BPMP during SC7 exit.
The earlier loop would fail just when the timer was about to wrap-around
(e.g. when TEGRA_TMRUS_BASE is 0xfffffffe, the target value becomes 0,
which would cause the loop to exit before it's expiry).
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch introduces the backend required for implementing the delay
timer API. Tegra has an on-chip free flowing us timer which can be
used as the delay timer.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch sets the 'USE_COHERENT_MEM' flag to '0', so that the
coherent memory region will not be included in the memory map.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch implements the get_sys_suspend_power_state() handler required by
the PSCI SYSTEM_SUSPEND API. The intent of this handler is to return the
appropriate State-ID field which can be utilized in `affinst_suspend()` to
suspend to system affinity level.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
danh-arm
Achin Gupta
Vikram Kanigiri
Jimmy Huang
yt.lee
Varun Wadekar
kenny liang
Soby Mathew
Sandrine Bailleux
CC Ma