The HAFGRTR_EL2 register is UNDEFINED unless the CPU supports both
FEAT_FGT and FEAT_AMUv1. FEAT_FGT is mandatory for v8.6-A and upwards,
but FEAT_AMUv1 is optional (from v8.4-A upwards), and as such any
8.6-A cores today without support for FEAT_AMUv1 will trigger an
undefined instruction exception on accessing this register.
Currently ARM_ARCH_AT_LEAST macro has been used to associate with an
architecture extension allowing to access HAFGRTR_EL2 register. This
condition should be replaced with macros specific to individual
features. This patch adds a new set of macros "ENABLE_FEAT_FGT,
ENABLE_FEAT_AMUv1, ENABLE_FEAT_ECV" under build options to provide
controlled access to the HAFGRTR_EL2 register.
Further to ensure that the the build options passed comply
with the given hardware implementation, a feature detection mechanism,
checking whether build options match with the architecture is required
at bootime. This will be implemented and pushed later in a separate
patch.
Signed-off-by: Jayanth Dodderi Chidanand <jayanthdodderi.chidanand@arm.com>
Change-Id: Ie390f4babe233b8b09455290277edbddecd33ead
Implemented a platform function 'plat_mboot_measure_critical_data' to
measure critical data and record its measurement using the Event Log
driver.
'bl2_plat_mboot_finish' function invokes this platform function
immediately after populating the critical data.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ia198295c6e07ab26d436eab1ff90df2cf28303af
It doesn't look correct to use mbed TLS defines directly in the Event
Log driver as this driver may use another Crypto library in future.
Hence mbed TLS Crypto dependency on Event Log driver is removed by
introducing generic Crypto defines and uses those in the Event Log
driver to call Crypto functions.
Also, updated mbed TLS glue layer to map these generic Crypto defines
to mbed TLS library defines.
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ibc9c751f60cbce4d3f3cf049b7c53b3d05cc6735
This patch allocates the RMI and GTSI FIDs from the reserved
range in Standard Secure Service call range of SMCCC.
Signed-off-by: Subhasish Ghosh <subhasish.ghosh@arm.com>
Change-Id: I82e77778882194c2a78ca6340788d53bab7c3a50
Add a UART/USART driver for STM32 with complete a hardware support;
it used for STM32CubeProgrammer support with even parity.
This driver is not used for console, which is already handle
by a simple driver (drivers/st/uart/aarch32/stm32_console.S).
Change-Id: Ia9266e5d177fe7fd09c8a15b81da1a05b1bc8b2d
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Sometimes when changing UART clock from TBG to XTAL, UART HW enters into
some broken state. It does not transit characters from TX FIFO anymore
and TX FIFO stays always empty. TX FIFO reset does not recover UART HW
from this broken state.
Experiments show that external reset can fix UART HW from this broken
state.
TF-A fatal error handler calls console_a3700_core_init() function to
initialize UART HW. This handler may be called anytime during CPU
runtime, also when kernel is running.
U-Boot or Linux kernel may change UART clock to TBG to achieve higher
baudrates. During initialization, console_a3700_core_init() resets UART
configuration to default settings, which means that it also changes
UART clock from TBG to XTAL.
Do an external reset of UART via North Bridge Peripheral reset register
to prevent this UART hangup.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I8990bce24d1a6fd8ccc47a2cd0a5ff932fcfcf14
Renamed a macro 'INVALID_ID' to 'EVLOG_INVALID_ID' to avoid its clash
with other macro names and to show it is explicitly used for Event
Log driver.
Change-Id: Ie4c92b3cd1366d9a59cd6f43221e24734865f427
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
This patch adds two new compile time options to enable SME in TF-A:
ENABLE_SME_FOR_NS and ENABLE_SME_FOR_SWD for use in non-secure and
secure worlds respectively. Setting ENABLE_SME_FOR_NS=1 will enable
SME for non-secure worlds and trap SME, SVE, and FPU/SIMD instructions
in secure context. Setting ENABLE_SME_FOR_SWD=1 will disable these
traps, but support for SME context management does not yet exist in
SPM so building with SPD=spmd will fail.
The existing ENABLE_SVE_FOR_NS and ENABLE_SVE_FOR_SWD options cannot
be used with SME as it is a superset of SVE and will enable SVE and
FPU/SIMD along with SME.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Iaaac9d22fe37b4a92315207891da848a8fd0ed73
Changing the SMC code value to conform with RMM for
transitioning a realm granule back to non-secure,
otherwise known as undelegate.
Signed-off-by: Mark Dykes <mark.dykes@arm.com>
Change-Id: Ia45ad6cab538de48c65b071b49e504be234afa2b
Use long instead of long long on aarch64 for 64_t stdint types.
Introduce inttypes.h to properly support printf format specifiers for
fixed width types for such change.
Change-Id: I0bca594687a996fde0a9702d7a383055b99f10a1
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Correctly handle USB_DESC_TYPE_OTHER_SPEED_CONFIGURATION request
in USB driver and support a different result than
USB_DESC_TYPE_CONFIGURATION with the new optional ops
get_other_speed_config_desc().
The support of this descriptor is optionnal and is only
required when high-speed capable device which can operate at its
other possible speed.
This patch allows to remove the pbuf update in usb_core_get_desc()
and solves an issue on USB re-enumeration on STM32MP15 platform
as the result of get_config_desc() is a const array.
This issue is not see on normal use-case, as the USB enumeration
is only done in ROM code and TF-A reuse the same USB descritors.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: I8edcc1e45065ab4e45d48f4bc37b49120674fdb0
Neoverse-N2 erratum 2242400 is a Cat B erratum that applies to
revision r0p0 of CPU. It is still open. The workaround
is to set CPUACTLR5_EL1[17] to 1'b1 followed by setting few
system control registers to specific values as per attached
SDEN document.
SDEN can be found here:
https://developer.arm.com/documentation/SDEN1982442/latest
Signed-off-by: nayanpatel-arm <nayankumar.patel@arm.com>
Change-Id: I6a9cb4a23238b8b511802a1ee9fcc5b207137649
Neoverse-N2 erratum 2138958 is a Cat B erratum that applies to
revision r0p0 of CPU. It is still open. The workaround
is to set CPUACTLR5_EL1[13] to 1'b1.
SDEN can be found here:
https://developer.arm.com/documentation/SDEN1982442/latest
Signed-off-by: nayanpatel-arm <nayankumar.patel@arm.com>
Change-Id: I5247f8f8eef08d38c169aad6d2c5501ac387c720
Neoverse-N2 erratum 2242415 is a Cat B erratum that applies to
revision r0p0 of CPU. It is still open. The workaround
is to set CPUACTLR_EL1[22] to 1'b1. Setting CPUACTLR_EL1[22]
will cause CFP instruction to invalidate all branch predictor
resources regardless of context.
SDEN can be found here:
https://developer.arm.com/documentation/SDEN1982442/latest
Signed-off-by: nayanpatel-arm <nayankumar.patel@arm.com>
Change-Id: I442be81fbc32e21fed51a84f59584df17f845e96
When an Arm Ltd GIC (Arm GIC-[567]00) is instantiated with one or more
ITSes, the ITS MMIO frames appear between the distributor and
redistributor addresses. This makes the beginning of the redistributor
region dependent on the existence and number of ITSes.
To support various FPGA images, with and without ITSes, probe the
addresses in question, to learn whether they accommodate an ITS or a
redistributor. This can be safely done by looking at the PIDR[01]
registers, which contain an ID code for each region, documented in the
Arm GIC TRMs.
We try to find all ITSes instantiated, and skip either two or four 64K
frames, depending on GICv4.1 support. At some point we will find the
first redistributor; this address we then update in the DTB.
Change-Id: Iefb88c2afa989e044fe0b36b7020b56538c60b07
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The GIC specification describes ID registers in each GIC register frame
(PIDRx), which can be used to identify a GIC component. The Arm Ltd. GIC
implementations use certain ID values to identify the distributor, the
redistributors and other parts like ITSes.
Introduce a function that reads those part number IDs, which are spread
over two registers. The actual numbers are only meaningful in connection
with a certain GIC model, which would need to be checked beforehand, by
the caller.
Change-Id: Ia6ff326a1e8b12664e4637bc8e2683d2b5c7721c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For platforms where we don't know the number of cores at compile time,
the size of the GIC redistributor frame is then also undetermined, since
it depends on this number of cores.
On top of this the GICR base address can also change, when an unknown
number of ITS frames (including zero) take up space between the
distributor and redistributor.
So while those two adjustments are done for independent reasons, the
code for doing so is very similar, so we should utilise the existing
fdt_adjust_gic_redist() function.
Add an (optional) gicr_base parameters to the prototype, so callers can
choose to also adjust this base address later, if needed.
Change-Id: Id39c0ba83e7401fdff1944e86950bb7121f210e8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Define a handler in the SPMD to route secure interrupts occurring while
the normal world runs. On a Group1 Secure interrupt (with a GICv3 or a
Group0 interrupt on GICv2), the normal world is pre-empted to EL3 and
redirected to the SPMD/SPMC for further handling.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Change-Id: I1350d74048c5549a2af8da0ba004c08512cc006a
* changes:
feat(plat/st/stm32mp1): add STM32MP_USB_PROGRAMMER target
feat(plat/st/stm32mp1): add USB DFU support for STM32MP1
feat(plat/st): add STM32CubeProgrammer support on USB
feat(drivers/st/usb): add device driver for STM32MP1
feat(plat/st): add a USB DFU stack
feat(drivers/usb): add a USB device stack
Add a device driver for Synopsis DWC2 USB IP of STM32MP15x,
this USB OTG device is only supported in device mode.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: I90b21f094f6637b85f3ace23a3a3a2f6fd4e0951
Add a new USB framework to manage an USB device profile (USBD)
based on a peripheral controller driver (PCD).
This USB stack can be use to implement any Universal Serial Bus Device
Class in TF-A on top of a USB driver defined in the platform.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: I7971ec6d952edec3511157a198e6e5359df4346b
This patch removes files that are not used by TF-R as well as
removes unused generic files from the TF-R makefile.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Idb15ac295dc77fd38735bf2844efdb73e6f7c89b
MPMM - the Maximum Power Mitigation Mechanism - is an optional
microarchitectural feature present on some Armv9-A cores, introduced
with the Cortex-X2, Cortex-A710 and Cortex-A510 cores.
MPMM allows the SoC firmware to detect and limit high activity events
to assist in SoC processor power domain dynamic power budgeting and
limit the triggering of whole-rail (i.e. clock chopping) responses to
overcurrent conditions.
This feature is enabled via the `ENABLE_MPMM` build option.
Configuration can be done via FCONF by enabling `ENABLE_MPMM_FCONF`, or
by via the plaform-implemented `plat_mpmm_topology` function.
Change-Id: I77da82808ad4744ece8263f0bf215c5a091c3167
Signed-off-by: Chris Kay <chris.kay@arm.com>
This change makes AMU auxiliary counters configurable on a per-core
basis, controlled by `ENABLE_AMU_AUXILIARY_COUNTERS`.
Auxiliary counters can be described via the `HW_CONFIG` device tree if
the `ENABLE_AMU_FCONF` build option is enabled, or the platform must
otherwise implement the `plat_amu_topology` function.
A new phandle property for `cpu` nodes (`amu`) has been introduced to
the `HW_CONFIG` specification to allow CPUs to describe the view of
their own AMU:
```
cpu0: cpu@0 {
...
amu = <&cpu0_amu>;
};
```
Multiple cores may share an `amu` handle if they implement the
same set of auxiliary counters.
AMU counters are described for one or more AMUs through the use of a new
`amus` node:
```
amus {
cpu0_amu: amu-0 {
#address-cells = <1>;
#size-cells = <0>;
counter@0 {
reg = <0>;
enable-at-el3;
};
counter@n {
reg = <n>;
...
};
};
};
```
This structure describes the **auxiliary** (group 1) AMU counters.
Architected counters have architecturally-defined behaviour, and as
such do not require DTB entries.
These `counter` nodes support two properties:
- The `reg` property represents the counter register index.
- The presence of the `enable-at-el3` property determines whether
the firmware should enable the counter prior to exiting EL3.
Change-Id: Ie43aee010518c5725a3b338a4899b0857caf4c28
Signed-off-by: Chris Kay <chris.kay@arm.com>
This change represents a general refactoring to clean up old code that
has been adapted to account for changes required to enable dynamic
auxiliary counters.
Change-Id: Ia85e0518f3f65c765f07b34b67744fc869b9070d
Signed-off-by: Chris Kay <chris.kay@arm.com>
This change decouples the group 1 counter macros to facilitate dynamic
detection at runtime. These counters remain disabled - we will add
dynamic enablement of them in a later patch.
Change-Id: I820d05f228d440643bdfa308d030bd51ebc0b35a
Signed-off-by: Chris Kay <chris.kay@arm.com>
This change removes the `AMU_GROUP0_COUNTERS_MASK` and
`AMU_GROUP0_MAX_COUNTERS` preprocessor definitions, instead retrieving
the number of group 0 counters dynamically through `AMCGCR_EL0.CG0NC`.
Change-Id: I70e39c30fbd5df89b214276fac79cc8758a89f72
Signed-off-by: Chris Kay <chris.kay@arm.com>
This change reduces preprocessor dependencies on the
`AMU_GROUP1_NR_COUNTERS` and `AMU_GROUP1_COUNTERS_MASK` definitions, as
these values will eventually be discovered dynamically.
In their stead, we introduce the `ENABLE_AMU_AUXILIARY_COUNTERS` build
option, which will enable support for dynamically detecting and
enabling auxiliary AMU counters.
This substantially reduces the amount of memory used by platforms that
know ahead of time that they do not have any auxiliary AMU counters.
Change-Id: I3d998aff44ed5489af4857e337e97634d06e3ea1
Signed-off-by: Chris Kay <chris.kay@arm.com>
This change introduces a small set of register getters and setters to
avoid having to repeatedly mask and shift in complex code.
Change-Id: Ia372f60c5efb924cd6eeceb75112e635ad13d942
Signed-off-by: Chris Kay <chris.kay@arm.com>
This change reduces the exposed surface area of the AMU API in order to
simplify the refactoring work in following patches. The functions and
definitions privatized by this change are not used by other parts of the
code-base today.
BREAKING CHANGE: The public AMU API has been reduced to enablement only
to facilitate refactoring work. These APIs were not previously used.
Change-Id: Ibf6174fb5b3949de3c4ba6847cce47d82a6bd08c
Signed-off-by: Chris Kay <chris.kay@arm.com>
With the introduction of MPMM, the auxiliary AMU counter logic requires
refactoring to move away from a single platform-defined group 1 counter
mask in order to support microarchitectural (per-core) group 1 counters.
BREAKING CHANGE: The `PLAT_AMU_GROUP1_COUNTERS_MASK` platform definition
has been removed. Platforms should specify per-core AMU counter masks
via FCONF or a platform-specific mechanism going forward.
Change-Id: I1e852797c7954f92409222b066a1ae57bc72bb05
Signed-off-by: Chris Kay <chris.kay@arm.com>
This change adds a new utility function - `fdtw_for_each_cpu` - to
invoke a callback for every CPU node listed in a flattened device tree
(FDT) with the node identifier and the MPIDR of the core it describes.
Signed-off-by: Chris Kay <chris.kay@arm.com>
Change-Id: Iabb5c0f0c9d11928a4a7a41cdc7d1e09aadeb2bc
This patch changes Cortex Demeter to Neoverse Demeter.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I7306d09ca60e101d0a96c9ceff9845422d75c160
This patch adds the basic CPU library code to support the Hunter CPU
in TF-A. This CPU is based on the Makalu core so that library code
was adapted as the basis for this patch.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I956b2dc0f43da7cec3e015252392e2694363e1b3
Currently on image entry, the data cache in the RW address range is
invalidated before MMU is enabled to safeguard against potential
stale data from previous firmware stage. If PIE is enabled however,
RO sections including the GOT may be also modified during pie fixup.
Therefore, to be on the safe side, invalidate the entire image
region if PIE is enabled.
Signed-off-by: Zelalem Aweke <zelalem.aweke@arm.com>
Change-Id: I7ee2a324fe4377b026e32f9ab842617ad4e09d89
This change aims to make the UFS code more robust by performing a
controller reset if linkstartup fails. This idea was borrowed from
Linux's ufshcd_link_startup function.
Signed-off-by: Jorge Troncoso <jatron@google.com>
Change-Id: I6b52148d1bf155b11198dc82a39b1120057adaaf
Manish Pandey
Jayanth Dodderi Chidanand
Alexei Fedorov
Manish V Badarkhe
Subhasish Ghosh
Sandrine Bailleux
Nicolas Le Bayon
Pali Rohár
johpow01
Mark Dykes
Olivier Deprez
Madhukar Pappireddy
Scott Branden
Patrick Delaunay
nayanpatel-arm
Andre Przywara
Patrick Delaunay
Chris Kay
Zelalem Aweke
Joanna Farley
Jorge Troncoso