1.Since in mmc_init, the most of mmc_device_info passed in are temporary variables.
In order to avoid referencing the released space on the stack when maybe MISUSED,
it`s better to use global variables to store mmc_device_info in mmc.c
2.Delete redundant;
Signed-off-by: deqi.hu@siengine.com
Change-Id: I51ae90e7f878b19b4963508b3f7ec66339015ebc
* changes:
drivers/gicv3: also shift eSPI register offset in GICD_OFFSET_64()
drivers/gicv3: add debug log for maximum INTID of SPI and eSPI
drivers/gicv3: limit SPI ID to avoid misjudgement in GICD_OFFSET()
drivers/gicv3: fix logical issue for num_eints
drivers/gicv3: fix potential GICD context override with ESPI enabled
drivers/gicv3: use mpidr to probe GICR for current CPU
* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mapping at BLE stage
plat/marvell/armada/common/mss: use MSS SRAM in secure mode
include/drivers/marvell/mochi: add detection of secure mode
plat/marvell: fix SPD handling in dram port
marvell: drivers: move XOR0/1 DIOB from WIN 0 to 1
drivers/marvell/mochi: add support for cn913x in PCIe EP mode
drivers/marvell/mochi: add missing stream IDs configurations
plat/marvell/armada/a8k: support HW RNG by SMC
drivers/rambus: add TRNG-IP-76 driver
TX FIFO has space for 32 characters. With default UART baudrate 115200 it
takes more than 2ms to transmit all 32 characters, so wait at least 3ms
before flushing TX FIFO.
If WTMI firmware transmitted something via UART before TF-A was booted,
some characters may still wait in TX FIFO when TF-A is initializing UART
driver. So wait at least 3ms to ensure that HW has enough time to transmit
all characters waiting in TX FIFO.
This fixes an issue where sometimes characters transmitted on UART by our
custom WTMI image are lost.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I8ea4ea58e4ba3e0c0d7f47e679171b9b94442f19
Console initialization function needs to wait at least minimal specified
time. The fastest Armada 3720 CPU is 1200 MHz so increase loop delay to
wait at least for 100 us on 1200 MHz variant too. The slowest Armada 3720
CPU is 600 MHz and in this case delay loop would take just 2 times more,
which is not a problem.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I1f0b4aabd0e08b7696feec631419f7f7c7ec17d2
The delay loop executes 3 instructions. These 3 instructions are executed
in 2 processor ticks and 30000 iterations on a 600 MHz CPU should yield
approximately 100 us. This means we are waiting 2 ms, not 20 ms, for TX
FIFO to be empty.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I2cccad405bcc73cd6d1062adc0205c405c16c15f
The FMC driver in TF-A only supports NAND Mode 0 timings.
The timings are then hard-coded as macros, leading to some parts of code
unreachable.
This issue was found by Coverity scan: CID 366361.
Change-Id: I864c51ce11b9ef74ad82b3301f56f46a2e0f70ca
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change CP110 XOR (DMA) to use WIN1 which is used for PCI-EP address
space only and using this window bypasses the need for translation
in the SMMU which has performance impact.
Change-Id: I98d99da59e904e6721cfa263ce44ad178a0fa956
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/20389
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Add initialization for TRNG-IP-76 driver and support SMC call
0xC200FF11 used for reading HW RNG value by secondary bootloader
software for KASLR support.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: I1d644f67457b28d347523f8a7bfc4eacc45cba68
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/32688
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Add Rambus (InsideSecure) TRNG-IP-76 HW RNG driver.
This IP is part of Marvell Armada CP110/CP115 die integrated
to Armada 7k/8K/CN913x SoCs
Change-Id: I9c5f510ad6728c7ed168da43d85b19d5852cd873
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
TZC_400_REGION_ATTR_FILTER_BIT_ALL is a simple constant definition, so
it can't get the real filter number to construct the bit flag for all
existing filters. If the platform doesn't have 4 filters, passing
FILTER_BIT_ALL to tzc400_configure_region() will cause assertion or
misconfiguration. So adjust the bit flag against the real filter
number.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Ie5c48303485f3b5015772961ee7c34746121ee84
ESPI register offset should also be shifted right by REG##R_SHIFT to
keep consistent.
It is not a functional issue, for GICD_OFFSET_64() is only used for
GICD_IROUTER<E>, and IROUTER_SHIFT is 0.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I76eee5c50e4300890e78e80bddde135ce88daa2d
Add debug log for the maximum supported INTID of SPI and eSPI on the
current GIC implementation.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Ie45ab1d85b39658c4ca4bc54ee433ac44e41d03f
The GICv3 architecture allows GICD_TYPER.ITLinesNumber to be 31, so
the maximum possible value for num_ints is 1024. The value must be
limited to (MAX_SPI_ID + 1), or GICD_OFFSET() will consider it as ESPI
INTID and return wrong register address.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Iddcb83d3e5d241b39f4176c19c2bceaa2c3dd653
In function gicv3_spis_config_defaults(), the variable num_ints is set
to (maximum SPI INTID + 1), while num_eints is set to (maximum ESPI
INTID). It introduces not only inconsistency to the code, but also
logical bug in the "for" loops, for the INTID of num_eints is also
valid and the check should be inclusive.
Fix this by setting num_eints to (maximum ESPI INTID + 1) as well.
Fix similar issues in gicv3_distif_save() and
gicv3_distif_init_restore().
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I4425777d17e84e85f38853603340bd348640154f
RESTORE/SAVE_GICD_EREGS uses (int_id - (MIN_ESPI_ID - MIN_SPI_ID)) to
get the context array index for ESPI, which will override the space of
standard SPI starting from (MIN_SPI_ID + MIN_SPI_ID).
However, using TOTAL_SPI_INTR_NUM to replace the above MIN_SPI_ID
cannot totally fix the issue, for TOTAL_SPI_INTR_NUM is not well
aligned and the array index will be rounded down by the shifting
operation if being shifted more than 2 bits. It will cause buffer
override again when the existing maximum SPI reaches 1019.
So round up TOTAL_SPI_INTR_NUM with (1 << REG##R_SHIFT) for GICD
context arrays.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I5be2837c42f381a62f8d46a4ecd778009b1fe059
In function gicv3_rdistif_probe(), line #1322 implies
gicv3_driver_data->mpidr_to_core_pos() may be null, but the original
code uses this interface to get current CPU index unconditionally.
It is better to use MPIDR to probe GICR which does not depend on
gicv3_driver_data->mpidr_to_core_pos().
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I64add055385040fe0a56b977e2299608e2309a6e
This patch does not change code, it only updates comments and macro name
for 6th bit of Status Register. So TF-A binary stay same.
6th bit of the Status Register is named TX EMPTY and is set to 1 when both
Transmitter Holding Register (THR) or Transmitter Shift Register (TSR) are
empty. It is when all characters were already transmitted.
There is also TX FIFO EMPTY bit in the Status Register which is set to 1
only when THR is empty.
In both console_a3700_core_init() and console_a3700_core_flush() functions
we should wait until both THR and TSR are empty therefore we should check
6th bit of the Status Register.
So current code is correct, just had misleading macro names and comments.
This change fixes this "documentation" issue, fixes macro name for 6th bit
of the Status Register and also updates comments.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I19e4e7f53a90bcfb318e6dd1b1249b6cbf81c4d3
Implementation is simple, just check if there is a pending character in
RX FIFO via RXRDY bit of Status Register and if yes, read it from
UART_RX_REG register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I226b6e336f44f5d0ca8dcb68e49a68e8f2f49708
Add pin control support for RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I08719015cab1ec59e2270523980a0a3e26e72c01
Add support for initializing DRAM on RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I99f1a6971a061a44687af498d55306a93e4fc8f7
Move DDR/QoS/PFC header files, so that the same code
can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I2cc0ceda8d05b6b8d95a69afdc233dc0d098e850
Move rpc driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I04805d720d95b8edcc14e652f897fadc7f432197
Move avs driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I85d9fa8b6abf158ce2521f1696478f7c5339fc42
Move authentication driver code to common directory, so that the
same code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I02592dfc714998bf89b9feaa78f685ae36be6f59
Move dma driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Idce2e2f4e098cfc17219f963373d20ebf74e5b7c
Move watch driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I235f2cde325a0feeadbfc4b7ee02e8b1186f7ea1
Move rom driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I399dfb5eff186db76d26fa9c54bea88bee66789c
Move delay driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I5e806bd0e0a0a4b436048513b7089db90ff9805f
Move console/scif driver code to common directory, so that the
same code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I0b15e4f4ffaaa99e77bcee32b1dad648eeadcd9b
Move pwrc driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I75d91a44d872fe2296b15c700efacd5721385363
Move io driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ic661e415c91a1fbfd5eee3bba86466037e51574b
Move eMMC driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I7f3055709337327d1a1c9f563c14ad1626adb355
Move plat common sources to common directory, so that same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Id2b1822c97cc50e3febaffc2e5f42b4d53809a17
Create a common directory and move the header and assembly files
so that the common code can be used by both Renesas R-Car Gen3 and
RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ia9a563a1c3c9f8c6f0d3cb82622deb2e155d7f6c
Write char if fifo is empty. If this is done like this all chars are
printed. Because origin code just put that chars to fifo and in case of
reset messages were missing.
Before this change chars are put to fifo and only check before adding if
fifo is full. The patch is changing this logic that it is adding char only
when fifo is empty to make sure that in case of reset (by another SW for
example) all chars are printed. Maybe one char can be missed but for IP
itself it is much easier to send just one char compare to full fifo.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Ic24c2c1252bce24be2aed68ee29477ca4a549e5f
This patch fixes checkpatch warnings and arrange header
as per TF-A coding style.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I46cd4d9b2851202324fe714e776cf3ad2ee1d923
Sort the headers alphabetically and replace TAB with a space
after #define.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I07c358294b7c02cbfa360112bbbde0eb5f2b50f5
deqi.hu
Manish Pandey
Madhukar Pappireddy
Pali Rohár
Yann Gautier
Ofer Heifetz
Konstantin Porotchkin
Heyi Guo
Peng Fan
Biju Das
Michal Simek