This patch fixes the incorrect bit width used to extract the wakeup
reason from PSYSR in platform_get_entrypoint() function. This defect
did not have any observed regression.
Change-Id: I42652dbffc99f5bf50cc86a5878f28d730720d9a
On ARM standard platforms, snoop and DVM requests used to be enabled
for the primary CPU's cluster only in the first EL3 bootloader.
In other words, if the platform reset into BL1 then CCI coherency
would be enabled by BL1 only, and not by BL3-1 again.
However, this doesn't cater for platforms that use BL3-1 along with
a non-TF ROM bootloader that doesn't enable snoop and DVM requests.
In this case, CCI coherency is never enabled.
This patch modifies the function bl31_early_platform_setup() on
ARM standard platforms so that it always enables snoop and DVM
requests regardless of whether earlier bootloader stages have
already done it. There is no harm in executing this code twice.
ARM Trusted Firmware Design document updated accordingly.
Change-Id: Idf1bdeb24d2e1947adfbb76a509f10beef224e1c
T210 is the latest chip in the Tegra family of SoCs from NVIDIA. It is an
ARM v8 dual-cluster (A57/A53) SoC, with any one of the clusters being active
at a given point in time.
This patch adds support to boot the Trusted Firmware on T210 SoCs. The patch
also adds support to boot secondary CPUs, enter/exit core power states for
all CPUs in the slow/fast clusters. The support to switch between clusters
is still not available in this patch and would be available later.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch fixes the incorrect bit width used to extract the primary
cpu id from `ap_data` exported by scp at SCP_BOOT_CFG_ADDR in
platform_is_primary_cpu().
Change-Id: I14abb361685f31164ecce0755fc1a145903b27aa
Fix the return type of the FVP `plat_arm_topology_setup` function
to be `void` instead of `int` to match the declaration in
`plat_arm.h`.
This does not result in any change in behavior.
Change-Id: I62edfa7652b83bd26cffb7d167153959b38e37e7
There has been a breaking change in the communication protocols used
between the AP cores and the SCP on CSS based platforms like Juno.
This means both the AP Trusted Firmware and SCP firmware must be
updated at the same time.
In case the user forgets to update the SCP ROM firmware, this patch
detects when it still uses the previous version of the communication
protocol. It will then output a comprehensive error message that helps
trouble-shoot the issue.
Change-Id: I7baf8f05ec0b7d8df25e0ee53df61fe7be0207c2
The communication protocol used between the AP cores and the SCP
in CSS-based platforms like Juno has undergone a number of changes.
This patch makes the required modifications to the SCP Boot Protocol,
SCPI Protocol and MHU driver code in shared CSS platform code so that
the AP cores are still able to communicate with the SCP.
This patch focuses on the mandatory changes to make it work. The
design of this code needs to be improved but this will come in
a subsequent patch.
The main changes are:
- MHU communication protocol
- The command ID and payload size are no longer written into the
MHU registers directly. Instead, they are stored in the payload
area. The MHU registers are now used only as a doorbell to kick
off messages. Same goes for any command result, the AP has to
pick it up from the payload area.
- SCP Boot Protocol
- The BL3-0 image is now expected to embed a checksum. This
checksum must be passed to the SCP, which uses it to check the
integrity of the image it received.
- The BL3-0 image used to be transferred a block (4KB)
at a time. The SCP now supports receiving up to 128KB at a
time, which is more than the size of the BL3-0 image.
Therefore, the image is now sent in one go.
- The command IDs have changed.
- SCPI Protocol
- The size of the SCPI payload has been reduced down from 512
bytes to 256 bytes. This changes the base address of the
AP-to-SCP payload area.
- For commands that have a response, the response is the same SCPI
header that was sent, except for the size and the status, which
both must be updated appropriately. Success/Failure of a command
is determined by looking at the updated status code.
- Some command IDs have changed.
NOTE: THIS PATCH BREAKS COMPATIBILITY WITH FORMER VERSIONS OF THE SCP
FIRMWARE AND THUS REQUIRES AN UPDATE OF THIS BINARY. THE LATEST SCP
BINARY CAN BE OBTAINED FROM THE ARM CONNECTED COMMUNITY WEBSITE.
Change-Id: Ia5f6b95fe32401ee04a3805035748e8ef6718da7
Move the Juno port from plat/juno to plat/arm/board/juno. Also rename
some of the files so they are consistently prefixed with juno_.
Update the platform makefiles accordingly.
Change-Id: I0af6cb52a5fee7ef209107a1188b76a3c33a2a9f
Major update to the Juno platform port to use the common platform code
in (include/)plat/arm/* and (include/)plat/common/*. This mainly
consists of removing duplicated code but also introduces some small
behavioural changes where there was unnecessary variation between the
FVP and Juno ports. See earlier commit titled `Add common ARM and CSS
platform code` for details.
Also move the ARM SoC specific security setup (i.e. NIC-400 and PCIe
initialization) from BL1 to `plat_arm_security_setup()` in BL2,
where the other security setup is done.
Change-Id: Ic9fe01bae8ed382bfb04fc5839a4cfff332eb124
Move the FVP port from plat/fvp to plat/arm/board/fvp. Also rename
some of the files so they are consistently prefixed with fvp_.
Update the platform makefiles accordingly.
Change-Id: I7569affc3127d66405f1548fc81b878a858e61b7
Major update to the FVP platform port to use the common platform code
in (include/)plat/arm/* and (include/)plat/common/*. This mainly
consists of removing duplicated code but also introduces some small
behavioural changes where there was unnecessary variation between the
FVP and Juno ports. See earlier commit titled `Add common ARM and CSS
platform code` for details.
Also add support for Foundation FVP version 9.1 during FVP config
setup to prevent a warning being emitted in the console.
Change-Id: I254ca854987642ce09d1b924c9fd410a6e13e3bc
This major change pulls out the common functionality from the
FVP and Juno platform ports into the following categories:
* (include/)plat/common. Common platform porting functionality that
typically may be used by all platforms.
* (include/)plat/arm/common. Common platform porting functionality
that may be used by all ARM standard platforms. This includes all
ARM development platforms like FVP and Juno but may also include
non-ARM-owned platforms.
* (include/)plat/arm/board/common. Common platform porting
functionality for ARM development platforms at the board
(off SoC) level.
* (include/)plat/arm/css/common. Common platform porting
functionality at the ARM Compute SubSystem (CSS) level. Juno
is an example of a CSS-based platform.
* (include/)plat/arm/soc/common. Common platform porting
functionality at the ARM SoC level, which is not already defined
at the ARM CSS level.
No guarantees are made about the backward compatibility of
functionality provided in (include/)plat/arm.
Also remove any unnecessary variation between the ARM development
platform ports, including:
* Unify the way BL2 passes `bl31_params_t` to BL3-1. Use the
Juno implementation, which copies the information from BL2 memory
instead of expecting it to persist in shared memory.
* Unify the TZC configuration. There is no need to add a region
for SCP in Juno; it's enough to simply not allow any access to
this reserved region. Also set region 0 to provide no access by
default instead of assuming this is the case.
* Unify the number of memory map regions required for ARM
development platforms, although the actual ranges mapped for each
platform may be different. For the FVP port, this reduces the
mapped peripheral address space.
These latter changes will only be observed when the platform ports
are migrated to use the new common platform code in subsequent
patches.
Change-Id: Id9c269dd3dc6e74533d0e5116fdd826d53946dc8
Some assembly files containing macros are included like header files
into other assembly files. This will cause assembler errors if they
are included multiple times.
Add header guards to assembly macro files to avoid assembler errors.
Change-Id: Ia632e767ed7df7bf507b294982b8d730a6f8fe69
The required platform constant PLATFORM_CACHE_LINE_SIZE is
unnecessary since CACHE_WRITEBACK_GRANULE effectively provides the
same information. CACHE_WRITEBACK_GRANULE is preferred since this
is an architecturally defined term and allows comparison with the
corresponding hardware register value.
Replace all usage of PLATFORM_CACHE_LINE_SIZE with
CACHE_WRITEBACK_GRANULE.
Also, add a runtime assert in BL1 to check that the provided
CACHE_WRITEBACK_GRANULE matches the value provided in CTR_EL0.
Change-Id: If87286be78068424217b9f3689be358356500dcd
In order for the symbol table in the ELF file to contain the size of
functions written in assembly, it is necessary to report it to the
assembler using the .size directive.
To fulfil the above requirements, this patch introduces an 'endfunc'
macro which contains the .endfunc and .size directives. It also adds
a .func directive to the 'func' assembler macro.
The .func/.endfunc have been used so the assembler can fail if
endfunc is omitted.
FixesARM-Software/tf-issues#295
Change-Id: If8cb331b03d7f38fe7e3694d4de26f1075b278fc
Signed-off-by: Kévin Petit <kevin.petit@arm.com>
For Juno r0, the platform reset handler needs to:
- Implement the workaround for defect #831273
- Increase the L2 Data and Tag RAM latencies for Cortex-A57.
Defect #831273 does not affect Juno r1. Also, the default value
for the L2 Tag RAM latency for Cortex-A57 is suitable on Juno r1.
The L2 Data RAM latency for Cortex-A57 still needs to be
increased, though.
This patch modifies the Juno platform reset handler to detect
the board revision and skip the unnecessary steps on Juno r1.
The behaviour on Juno r0 is unchanged.
Change-Id: I27542917223e680ef923ee860900806ffcd0357b
This patch updates the FVP and Juno platform ports to use the common
driver for ARM Cache Coherent Interconnects.
Change-Id: Ib142f456b9b673600592616a2ec99e9b230d6542
This patch defines the ARRAY_SIZE macro for calculating number of elements
in an array and uses it where appropriate.
Change-Id: I72746a9229f0b259323972b498b9a3999731bc9b
Cortex-A57 erratum #806969 applies to revision r0p0 of the CPU
but does not manifest itself on Juno r0. It is not applicable
to Juno r1 in any case.
This patch modifies the Juno platform Makefile to no longer
compile this erratum workaround in.
Change-Id: I32b16835b2ac897e639e869ab2b78b62a51a0139
This patch modifies the declarations of the functions printf() et al.
and adds the right GCC attribute to request the compiler to check
the type of the arguments passed to these functions against the given
format string. This will ensure that the compiler outputs warning
messages like the following whenever it detects an inconsistency:
file.c:42: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘long int’
It also fixes the type mismatch inconsistencies that it revealed
across the code base.
NOTE: THIS PATCH MAY FORCE PLATFORM PORTS OR SP/SPDS THAT USE THE
PRINTF FAMILY OF FUNCTIONS TO FIX ANY TYPE MISMATCH INCONSISTENCIES.
Change-Id: If36bb54ec7d6dd2cb4791d89b02a24ac13fd2df6
All coding style violations have been fixed in a previous patch and
since then, each individual patch has been checked in this regard.
However, the latest version of the checkpatch.pl script from the Linux
kernel is more advanced and it is able to flag new errors in the
Trusted Firmware codebase. This patch fixes them.
Change-Id: I1f332f2440984be85d36b231bb83260368987077
By default the SMMU for the DMA-330 is configured to mark some stream IDs
as always belonging to the Secure world. As a result, if EL1 software turns
the SMMU on, certain Non-Secure accesses get rewritten as Secure, making
them bypass translation and access Secure physical addresses directly.
Since the current Juno board firmware configures the DMA-330 hardware as
Non-Secure, rewrite the SMMU's default SSD table as well to prevent any
unexpected behaviour in EL1.
Change-Id: Iaa81d883eecf28d80eb182b9ce475684bf9c718c
This patch removes the plat_get_max_afflvl() platform API
and instead replaces it with a platform macro PLATFORM_MAX_AFFLVL.
This is done because the maximum affinity level for a platform
is a static value and it is more efficient for it to be defined
as a platform macro.
NOTE: PLATFORM PORTS NEED TO BE UPDATED ON MERGE OF THIS COMMIT
FixesARM-Software/tf-issues#265
Change-Id: I31d89b30c2ccda30d28271154d869060d50df7bf
This patch defines MAX_MMAP_REGIONS separately for each BL stage
as per its requirements. This minimizes the size of the mmap[]
array.
FixesARM-Software/tf-issues#201
Change-Id: I19b15e1a91a8365b2ecf24e2cd71937cb73916b2
This patch adds support to authenticate the Trusted Key certificate
and the BL3-x certificates and images at BL2.
Change-Id: I69a8c13a14c8da8b75f93097d3a4576aed71c5dd
This patch moves fvp_io_setup() to bl2_early_platform_setup() in order
to allow BL2 to use the IO framework before bl2_platform_setup().
Change-Id: I75e1a772ab5f9b4727f6727822a2527c30f3c63d
This patch adds support to authenticate the BL2 content certificate
and image using the authentication module in BL1.
The FIP driver has been extended to include the BL2 certificate
UUID.
FVP and Juno ports include the BL2 certificate FIP file
definition.
Change-Id: I32680e9bd123c8db4a4193c14448c9b32b0e9325
This patch implements an authentication module based on the
PolarSSL library (v1.3.9) to verify the Chain of Trust when
Trusted Boot is enabled.
PolarSSL sources must be fetched separately. The POLARSSL_DIR
build option may be used to indicate the path to the PolarSSL
main directory (this directory must contain the 'include' and
'library' subdirectories).
To be able to build PolarSSL sources as a part of the Trusted
Firmware build process, the DISABLE_PEDANTIC flag in polarssl.mk
will tell the build system to remove the -pedantic option from
the CFLAGS.
Inclusion of PolarSSL increases the memory requirements of the BL1
and BL2 images. The following are the changes made to the FVP and
Juno platforms to cater for this when TRUSTED_BOARD_BOOT is
defined:
Changes on FVP:
- BL1 and BL2 stacks have been increased to 4 KB
- BL1(rw) section has been increased to 32 KB.
- BL2 memory region has been increased to 112 KB
Changes on Juno:
- BL1 and BL2 stacks have been increased to 4 KB
- BL1(rw) section has been increased to 32 KB.
- Trusted ROM region in Flash has been increased to 128 KB.
- BL2 memory region has been increased to 116 KB
Change-Id: Ie87d80d43408eb6239c4acd0ec5ab2120e4e9e80
This patch adds the function plat_match_rotpk() to the platform
porting layer to provide a Root Of Trust Public key (ROTPK)
verification mechanism. This function is called during the
Trusted Board Boot process and receives a supposed valid copy
of the ROTPK as a parameter, usually obtained from an external
source (for instance, a certificate). It returns 0 (success) if
that key matches the actual ROTPK stored in the system or any
other value otherwise.
The mechanism to access the actual ROTPK stored in the system
is platform specific and should be implemented as part of this
function. The format of the ROTPK is also platform specific
(to save memory, some platforms might store a hash of the key
instead of the whole key).
TRUSTED_BOARD_BOOT build option has been added to allow the user
to enable the Trusted Board Boot features. The implementation of
the plat_match_rotpk() funtion is mandatory when Trusted Board
Boot is enabled.
For development purposes, FVP and Juno ports provide a dummy
function that returns always success (valid key). A safe trusted
boot implementation should provide a proper matching function.
Documentation updated accordingly.
Change-Id: I74ff12bc2b041556c48533375527d9e8c035b8c3
This patch adds a tool that generates all the necessary elements
to establish the chain of trust (CoT) between the images.
The tool reads the binary images and signing keys and outputs the
corresponding certificates that will be used by the target at run
time to verify the authenticity of the images.
Note: the platform port must provide the file platform_oid.h. This
file will define the OIDs of the x509 extensions that will be added
to the certificates in order to establish the CoT.
Change-Id: I2734d6808b964a2107ab3a4805110698066a04be
This patch adds support to call the reset_handler() function in BL3-1 in the
cold and warm boot paths when another Boot ROM reset_handler() has already run.
This means the BL1 and BL3-1 versions of the CPU and platform specific reset
handlers may execute different code to each other. This enables a developer to
perform additional actions or undo actions already performed during the first
call of the reset handlers e.g. apply additional errata workarounds.
Typically, the reset handler will be first called from the BL1 Boot ROM. Any
additional functionality can be added to the reset handler when it is called
from BL3-1 resident in RW memory. The constant FIRST_RESET_HANDLER_CALL is used
to identify whether this is the first version of the reset handler code to be
executed or an overridden version of the code.
The Cortex-A57 errata workarounds are applied only if they have not already been
applied.
FixesARM-software/tf-issue#275
Change-Id: Id295f106e4fda23d6736debdade2ac7f2a9a9053
This patch allows the secure payload (BL3-2) to be loaded in the
DRAM region secured by the TrustZone controller (top 16 MB of DRAM1).
The location of BL3-2 can be selected at build time by setting the
build flag FVP_TSP_RAM_LOCATION to one of the following options:
- 'tsram' : Trusted SRAM (this is the default option)
- 'tdram' : Trusted DRAM
- 'dram' : Secure region in DRAM1 (top 16MB configured by the
TrustZone controller)
The number of MMU tables in BL3-2 depends on its location in
memory: 3 in case it is loaded in DRAM, 2 otherwise.
Documentation updated accordingly.
FixesARM-software/tf-issues#212
Change-Id: I371eef3a4159f06a0c9e3c6c1f4c905b2f93803a
This patch allows the platform to validate the power_state and
entrypoint information from the normal world early on in PSCI
calls so that we can return the error safely. New optional
pm_ops hooks `validate_power_state` and `validate_ns_entrypoint`
are introduced to do this.
As a result of these changes, all the other pm_ops handlers except
the PSCI_ON handler are expected to be successful. Also, the PSCI
implementation will now assert if a PSCI API is invoked without the
corresponding pm_ops handler being registered by the platform.
NOTE : PLATFORM PORTS WILL BREAK ON MERGE OF THIS COMMIT. The
pm hooks have 2 additional optional callbacks and the return type
of the other hooks have changed.
FixesARM-Software/tf-issues#229
Change-Id: I036bc0cff2349187c7b8b687b9ee0620aa7e24dc
This patch removes the non-secure entry point information being passed
to the platform pm_ops which is not needed. Also, it removes the `mpidr`
parameter for platform pm hooks which are meant to do power management
operations only on the current cpu.
NOTE: PLATFORM PORTS MUST BE UPDATED AFTER MERGING THIS COMMIT.
Change-Id: If632376a990b7f3b355f910e78771884bf6b12e7
This patch extends the build option `USE_COHERENT_MEMORY` to
conditionally remove coherent memory from the memory maps of
all boot loader stages. The patch also adds necessary
documentation for coherent memory removal in firmware-design,
porting and user guides.
FixesARM-Software/tf-issues#106
Change-Id: I260e8768c6a5c2efc402f5804a80657d8ce38773
This patch moves the bakery locks out of coherent memory to normal memory.
This implies that the lock information needs to be placed on a separate cache
line for each cpu. Hence the bakery_lock_info_t structure is allocated in the
per-cpu data so as to minimize memory wastage. A similar platform per-cpu
data is introduced for the platform locks.
As a result of the above changes, the bakery lock api is completely changed.
Earlier, a reference to the lock structure was passed to the lock implementation.
Now a unique-id (essentially an index into the per-cpu data array) and an offset
into the per-cpu data for bakery_info_t needs to be passed to the lock
implementation.
Change-Id: I1e76216277448713c6c98b4c2de4fb54198b39e0
This patch maps the non-secure region of DRAM1 in the MMU. The
non-secure region comprises the whole DRAM1 (0x80000000 -
0xffffffff) excluding the top 16 MB (0xff000000 - 0xffffffff).
The TrustZone controller configures this 16 MB region as secure
memory, so it can not be accessed in non-secure mode.
The number of MMU tables in BL2 has been increased to 3 because
the new size of the non-secure region in DRAM requires an extra L2
table.
Change-Id: I5ad080c6e181f6b6060e15cebb1d18b7fa128cf5
This patch allows the BL3-1 NOBITS section to overlap the BL1 R/W
section since the former will always be used after the latter.
Similarly, the BL3-2 NOBITS section can overlay the BL2 image
when BL3-2 is loaded in Trusted SRAM.
Due to the current size of the images, there is no actual overlap.
Nevertheless, this reorganization may help to optimise the Trusted
SRAM usage when the images size grows.
Note that because BL3-1 NOBITS section is allowed to overlap the
BL1 R/W section, BL1 global variables will remain valid only until
execution reaches the BL3-1 entry point during a cold boot.
Documentation updated accordingly.
FixesARM-software/tf-issues#254
Change-Id: Id538f4d1c7f1f7858108280fd7b97e138572b879
In both FVP and Juno ports, IRQ #16, which is a PPI, is incorrectly
identified as secure SGI #8 through the constant IRQ_SEC_SGI_8.
This patch removes it.
FixesARM-software/tf-issues#282
Change-Id: I9e52d849611ffcd2b1f28e56dd156c5b217ed63e
This patch reassigns the crash console on Juno and FVP to use the runtime
BL3-1 console. The crash console is changed to SoC UART0 (UART2) from the
previous FPGA UART0 (UART0) on Juno. In FVP, it is changed from UART0 to
UART1.
FixesARM-software/tf-issues#256
Change-Id: I7df54f86ca00ec2652c27261dd66a94c12610816
This patch replaces the usage of the GIC private driver in Juno with
the generic ARM GIC driver. The private driver is no longer necessary
and has been removed from the Juno port.
FixesARM-software/tf-issues#253
Change-Id: I6aaabc252e5e6fb5fcf44ab6d0febd9b38791056
This patch optimizes the Cortex-A57 cluster power down sequence by not
flushing the Level1 data cache. The L1 data cache and the L2 unified
cache are inclusive. A flush of the L2 by set/way flushes any dirty
lines from the L1 as well. This is a known safe deviation from the
Cortex-A57 TRM defined power down sequence. This optimization can be
enabled by the platform through the 'SKIP_A57_L1_FLUSH_PWR_DWN' build
flag. Each Cortex-A57 based platform must make its own decision on
whether to use the optimization.
This patch also renames the cpu-errata-workarounds.md to
cpu-specific-build-macros.md as this facilitates documentation
of both CPU Specific errata and CPU Specific Optimization
build macros.
Change-Id: I299b9fe79e9a7e08e8a0dffb7d345f9a00a71480
This patch deprecates the build option to relocate the shared data
into Trusted DRAM in FVP. After this change, shared data is always
located at the base of Trusted SRAM. This reduces the complexity
of the memory map and the number of combinations in the build
options.
FixesARM-software/tf-issues#257
Change-Id: I68426472567b9d8c6d22d8884cb816f6b61bcbd3
This patch adds support on the Juno platform for entering a wfi in
response to a PSCI CPU_SUSPEND call where the state type is a
standby state.
Change-Id: I0a102dee1f8d2ad936c63ad1d1d3ad001a4a4768
This patch configures the TrustZone Controller in Juno to split
the 2GB DDR-DRAM memory at 0x80000000 into Secure and Non-Secure
regions:
- Secure DDR-DRAM: top 16 MB, except for the last 2 MB which are
used by the SCP for DDR retraining
- Non-Secure DDR-DRAM: remaining DRAM starting at base address
Build option PLAT_TSP_LOCATION selects the location of the secure
payload (BL3-2):
- 'tsram' : Trusted SRAM (default option)
- 'dram' : Secure region in the DDR-DRAM (set by the TrustZone
controller)
The MMU memory map has been updated to give BL2 permission to load
BL3-2 into the DDR-DRAM secure region.
FixesARM-software/tf-issues#233
Change-Id: I6843fc32ef90aadd3ea6ac4c7f314f8ecbd5d07b
This patch replaces direct accesses to the TZC-400 registers by the
appropiate calls to the generic driver available in the Trusted
Firmware in order to initialize the TrustZone Controller.
Functions related to the initialization of the secure memory,
like the TZC-400 configuration, have been moved to a new file
'plat_security.c'. This reorganization makes easier to set up
the secure memory from any BL stage.
TZC-400 initialization has been moved from BL1 to BL2 because BL1
does not access the non-secure memory. It is BL2's responsibility
to enable and configure the TZC-400 before loading the next BL
images.
In Juno, BL3-0 initializes some of the platform peripherals, like
the DDR controller. Thus, BL3-0 must be loaded before configuring
the TrustZone Controller. As a consequence, the IO layer
initialization has been moved to early platform initialization.
FixesARM-software/tf-issues#234
Change-Id: I83dde778f937ac8d2996f7377e871a2e77d9490e
This patch uses the IMAGE_BL<x> constants to create translation tables specific
to a boot loader stage. This allows each stage to create mappings only for areas
in the memory map that it needs.
FixesARM-software/tf-issues#209
Change-Id: Ie4861407ddf9317f0fb890fc7575eaa88d0de51c
This patch avoids the problem of crash reporting mechanism accessing
global data in BSS by 'plat_print_gic_regs' for FVP platforms. Earlier
it depended on the global 'plat_config' object for the GIC Base address
in FVP platforms which would have caused exception if it were accessed
before the BSS was initialized. It is now fixed by dynamically
querying the V2M_SYS_ID to find the FVP model type and accordingly
selecting the appropriate GIC Base address.
This patch also fixes the 'plat_print_gic_regs' to use the correct GIC
Distributor base address for printing GICD_IS_PENDR register values
for both Juno and FVP platforms.
FixesARM-Software/tf-issues#236
Change-Id: I545c7b908b3111419bf27db0575ce86acf86784b
This patch gathers miscellaneous minor fixes to the documentation, and comments
in the source code.
Change-Id: I631e3dda5abafa2d90f464edaee069a1e58b751b
Co-Authored-By: Soby Mathew <soby.mathew@arm.com>
Co-Authored-By: Dan Handley <dan.handley@arm.com>
This patch changes the UART port assignment for various BL stages
so as to make it consistent on the platform ports. The BL1, BL2 and
BL3-1 now uses UART0 on the FVP port and SoC UART0 on the Juno port.
The BL3-2 uses UART2 on the FVP port and FPGA UART0 on the Juno
port.
This provides an interim fix to ARM-software/tf-issues#220 until
support is added for changing the UART port for a BL image between
cold boot and runtime.
Change-Id: Iae5faea90be3d59e41e597b34a902f93e737505a
This patch removes the PRIMARY_CPU definition hardcoded in the
Juno port. Instead, the primary CPU is obtained at runtime by
reading the SCC General Purpose Register 1 (GPR_1), whose value
is copied by the SCP into shared memory during the boot process.
Change-Id: I3981daa92eb7142250712274cf7f655b219837f5
This patch adds the Juno platform specific handlers for PSCI
SYSTEM_OFF and SYSTEM_RESET operations.
Change-Id: Ie389adead533ec2314af44d721b4d0f306147c7d
This patch implements the TSP on Juno. It executes from on-chip Trusted
SRAM.
Also, the other bootloader images (i.e. BL1 R/W, BL2 and BL3-1) have
been moved around. The reason is, although there was enough space
overall to store the TSP in SRAM, there was no contiguous free chunk
of SRAM big enough to hold it.
This patch keeps the overall memory layout (i.e. keeping BL1 R/W at
the bottom, BL2 at the top and BL3-1 in between) but moves the base
addresses of all the bootloader images in such a way that:
- memory fragmentation is reduced enough to fit BL3-2 in;
- new base addresses are suitable for release builds as well as debug
ones;
- each image has a few extra kilobytes for future growth.
BL3-1 and BL3-2 are the images which received the biggest allocations
since they will most probably grow the most.
This patch also adds instruction synchronization barriers around the code which
handles the timer interrupt in the TSP. This ensures that the interrupt is not
acknowledged after or EOIed before it is deactivated at the peripheral.
Change-Id: I1c5b51858700027ee283ac85d18e06863a27c72e
This patch adds support for PSCI CPU_OFF and CPU_SUSPEND APIs to the Juno port
of the ARM Trusted Firmware. The maximum affinity level that can be suspended is
the cluster level (affinity level 1). Support for suspending the system level is
not present.
Change-Id: Ie2c9da0acd7d1b0d5ac64940cdf40347153e52c8
This patch adds the initial port of the ARM Trusted Firmware on the Juno
development platform. This port does not support a BL3-2 image or any PSCI APIs
apart from PSCI_VERSION and PSCI_CPU_ON. It enables workarounds for selected
Cortex-A57 (#806969 & #813420) errata and implements the workaround for a Juno
platform errata (Defect id 831273).
Change-Id: Ib3d92df3af53820cfbb2977582ed0d7abf6ef893
This patch adds CPU core and cluster power down sequences to the CPU specific
operations framework introduced in a earlier patch. Cortex-A53, Cortex-A57 and
generic AEM sequences have been added. The latter is suitable for the
Foundation and Base AEM FVPs. A pointer to each CPU's operations structure is
saved in the per-cpu data so that it can be easily accessed during power down
seqeunces.
An optional platform API has been introduced to allow a platform to disable the
Accelerator Coherency Port (ACP) during a cluster power down sequence. The weak
definition of this function (plat_disable_acp()) does not take any action. It
should be overriden with a strong definition if the ACP is present on a
platform.
Change-Id: I8d09bd40d2f528a28d2d3f19b77101178778685d
This patch adds an optional platform API (plat_reset_handler) which allows the
platform to perform any actions immediately after a cold or warm reset
e.g. implement errata workarounds. The function is called with MMU and caches
turned off. This API is weakly defined and does nothing by default but can be
overriden by a platform with a strong definition.
Change-Id: Ib0acdccbd24bc756528a8bd647df21e8d59707ff
This patch introduces a framework which will allow CPUs to perform
implementation defined actions after a CPU reset, during a CPU or cluster power
down, and when a crash occurs. CPU specific reset handlers have been implemented
in this patch. Other handlers will be implemented in subsequent patches.
Also moved cpu_helpers.S to the new directory lib/cpus/aarch64/.
Change-Id: I1ca1bade4d101d11a898fb30fea2669f9b37b956
This patch provides a workaround for the ASM_ASSERT label issue
and also reworks the use of labels in assembly macros.
If the caller of the ASM_ASSERT macro happened to use the
label '1' to jump past the ASM_ASSERT macro, it would not have
worked since the ASM_ASSERT macro internally used the same label.
Hence, as a workaround, this patch makes the label a high
number in the expectation that the caller will never use it.
Also updated the other assembly macros using numerical labels to
named lables.
Change-Id: Iec892359db84f2391ad2a83a92141c4d7049776a
This patch reworks FVP port's power management implementation to perform
platform actions only when the platform exported hook is invoked for the highest
affinity level to enter/exit the OFF state.
For example, during a CPU_OFF operation, fvp_affinst_off() is called twice: for
affinity level 0 and affinity level 1 (in that order). CPU specific operations
are deferred until the next invocation if it is determined through a call to
psci_get_max_phys_off_afflvl() that this is CPU is the last in the cluster.
Similarly, during power up if the CPU is the first in the cluster, both CPU and
cluster specific operations are performed when fvp_affinst_on_finish() is
invoked for affinity level 1. Earlier, they were done across the two invocations
of the handler.
Change-Id: I4288ed3ba1385db36a69cc2e598deb219f209b8a
This patch adds support for SYSTEM_OFF and SYSTEM_RESET PSCI
operations. A platform should export handlers to complete the
requested operation. The FVP port exports fvp_system_off() and
fvp_system_reset() as an example.
If the SPD provides a power management hook for system off and
system reset, then the SPD is notified about the corresponding
operation so it can do some bookkeeping. The TSPD exports
tspd_system_off() and tspd_system_reset() for that purpose.
Versatile Express shutdown and reset methods have been removed
from the FDT as new PSCI sys_poweroff and sys_reset services
have been added. For those kernels that do not support yet these
PSCI services (i.e. GICv3 kernel), the original dtsi files have
been renamed to *-no_psci.dtsi.
FixesARM-software/tf-issues#218
Change-Id: Ic8a3bf801db979099ab7029162af041c4e8330c8
* Move TSP platform porting functions to new file:
include/bl32/tsp/platform_tsp.h.
* Create new TSP_IRQ_SEC_PHY_TIMER definition for use by the generic
TSP interrupt handling code, instead of depending on the FVP
specific definition IRQ_SEC_PHY_TIMER.
* Rename TSP platform porting functions from bl32_* to tsp_*, and
definitions from BL32_* to TSP_*.
* Update generic TSP code to use new platform porting function names
and definitions.
* Update FVP port accordingly and move all TSP source files to:
plat/fvp/tsp/.
* Update porting guide with above changes.
Note: THIS CHANGE REQUIRES ALL PLATFORM PORTS OF THE TSP TO
BE UPDATED
FixesARM-software/tf-issues#167
Change-Id: Ic0ff8caf72aebb378d378193d2f017599fc6b78f
The TZC-400 driver previously allowed the possibility of multiple
controller instances to be present in the same executable. This
was unnecessary since there will only ever be one instance.
This change simplifies the tzc_init() function to only take the
base address argument needed by implementation, conforming to the
driver initialization model of other drivers. It also hides some
of the implementation details that were previously exposed by the
API.
The FVP port has been updated accordingly.
THIS CHANGE REQUIRES ALL PLATFORM PORTS THAT USE THE TZC-400
DRIVER TO BE UPDATED
FixesARM-software/tf-issues#181
Change-Id: I7b721edf947064989958d8f457d6462d92e742c8
Move the remaining IO storage source file (io_storage.c) from the
lib to the drivers directory. This requires that platform ports
explicitly add this file to the list of source files.
Also move the IO header files to a new sub-directory, include/io.
Change-Id: I862b1252a796b3bcac0d93e50b11e7fb2ded93d6
The intent of io_init() was to allow platform ports to provide
a data object (io_plat_data_t) to the IO storage framework to
allocate into. The abstraction was incomplete because io_plat_data_t
uses a platform defined constant and the IO storage framework
internally allocates other arrays using platform defined constants.
This change simplifies the implementation by instantiating the
supporting objects in the IO storage framework itself. There is now
no need for the platform to call io_init().
The FVP port has been updated accordingly.
THIS CHANGE REQUIRES ALL PLATFORM PORTS THAT USE THE IO STORAGE
FRAMEWORK TO BE UDPATED.
Change-Id: Ib48ac334de9e538064734334c773f8b43df3a7dc
* Create cci_init() function in CCI-400 driver to allow platform
to provide arguments needed by the driver (i.e. base address
and cluster indices for the ACE slave interfaces).
* Rename cci_(en|dis)able_coherency to
cci_(en|dis)able_cluster_coherency to make it clear that
the driver only enables/disables the coherency of CPU
clusters and not other devices connected to the CCI-400.
* Update FVP port to use new cci_init() function and remove
unnecessary CCI defintions from platform_def.h. Also rename
fvp_cci_setup() to fvp_cci_enable() to more clearly
differentiate between CCI initialization and enabling.
THIS CHANGE REQUIRES PLATFORM PORTS THAT USE THE CCI-400 DRIVER
TO BE UPDATED
FixesARM-software/tf-issues#168
Change-Id: I1946a51409b91217b92285b6375082619f607fec
This patch groups the current contents of the Trusted DRAM region at
address 0x00_0600_0000 (entrypoint mailboxes and BL3-1 parameters) in
a single shared memory area that may be allocated to Trusted SRAM
(default) or Trusted DRAM at build time by setting the
FVP_SHARED_DATA_LOCATION make variable. The size of this shared
memory is 4096 bytes.
The combination 'Shared data in Trusted SRAM + TSP in Trusted DRAM'
is not currently supported due to restrictions in the maximum number
of mmu tables that can be created.
Documentation has been updated to reflect these changes.
FixesARM-software/tf-issues#100
Change-Id: I26ff04d33ce4cacf8d770d1a1e24132b4fc53ff0
Fix the following issues with the console log output:
* Make sure the welcome string is the first thing in the log output
(during normal boot).
* Prefix each message with the BL image name so it's clear which
BL the output is coming from.
* Ensure all output is wrapped in one of the log output macros so it can
be easily compiled out if necessary. Change some of the INFO() messages
to VERBOSE(), especially in the TSP.
* Create some extra NOTICE() and INFO() messages during cold boot.
* Remove all usage of \r in log output.
FixesARM-software/tf-issues#231
Change-Id: Ib24f7acb36ce64bbba549f204b9cde2dbb46c8a3
Secure ROM at address 0x0000_0000 is defined as FVP_TRUSTED_ROM
Secure RAM at address 0x0400_0000 is defined as FVP_TRUSTED_SRAM
Secure RAM at address 0x0600_0000 is defined as FVP_TRUSTED_DRAM
BLn_BASE and BLn_LIMIT definitions have been updated and are based on
these new memory regions.
The available memory for each bootloader in the linker script is
defined by BLn_BASE and BLn_LIMIT, instead of the complete memory
region.
TZROM_BASE/SIZE and TZRAM_BASE/SIZE are no longer required as part of
the platform porting.
FVP common definitions are defined in fvp_def.h while platform_def.h
contains exclusively (with a few exceptions) the definitions that are
mandatory in the porting guide. Therefore, platform_def.h now includes
fvp_def.h instead of the other way around.
Porting guide has been updated to reflect these changes.
Change-Id: I39a6088eb611fc4a347db0db4b8f1f0417dbab05
This patch separates the stack size for each BL stage and
reduces it after stack usage analysis was done.
FixesARM-software/tf-issues#200
Change-Id: I8edc6de2551b0a6788761d121937692b2149bb29
There is no mechanism which allows the TSPD to specify what SPSR to
use when entering BL3-2 instead of BL3-3. This patch divides the
responsibility between tspd_setup() and tspd_init() for initializing
the TSPD and TSP to support the alternate BL3-2 initialization flow
where BL3-1 handsover control to BL3-2 instead of BL3-3.
SPSR generated by TSPD for TSP is preserved due the new division of
labour which fixes#174.
This patch also moves the cpu_context initialization code from
tspd_setup() to tspd_init() immediately before entering the TSP.
Instead tspd_setup() updates the BL3-2 entrypoint info structure
with the state required for initializing the TSP later.
Fixes ARM-software/TF-issues#174
Change-Id: Ida0a8a48d466c71d5b07b8c7f2af169b73f96940
The purpose of platform_is_primary_cpu() is to determine after reset
(BL1 or BL3-1 with reset handler) if the current CPU must follow the
cold boot path (primary CPU), or wait in a safe state (secondary CPU)
until the primary CPU has finished the system initialization.
This patch removes redundant calls to platform_is_primary_cpu() in
subsequent bootloader entrypoints since the reset handler already
guarantees that code is executed exclusively on the primary CPU.
Additionally, this patch removes the weak definition of
platform_is_primary_cpu(), so the implementation of this function
becomes mandatory. Removing the weak symbol avoids other
bootloaders accidentally picking up an invalid definition in case the
porting layer makes the real function available only to BL1.
The define PRIMARY_CPU is no longer mandatory in the platform porting
because platform_is_primary_cpu() hides the implementation details
(for instance, there may be platforms that report the primary CPU in
a system register). The primary CPU definition in FVP has been moved
to fvp_def.h.
The porting guide has been updated accordingly.
FixesARM-software/tf-issues#219
Change-Id: If675a1de8e8d25122b7fef147cb238d939f90b5e
Assert a valid security state using the macro sec_state_is_valid().
Replace assert() with panic() in those cases that might arise
because of runtime errors and not programming errors.
Replace panic() with assert() in those cases that might arise
because of programming errors.
FixesARM-software/tf-issues#96
Change-Id: I51e9ef0439fd5ff5e0edfef49050b69804bf14d5
This patch adds the CPUECTLR_EL1 register and the CCI Snoop Control
register to the list of registers being reported when an unhandled
exception occurs.
Change-Id: I2d997f2d6ef3d7fa1fad5efe3364dc9058f9f22c
This patch reworks the crash reporting mechanism to further
optimise the stack and code size. The reporting makes use
of assembly console functions to avoid calling C Runtime
to report the CPU state. The crash buffer requirement is
reduced to 64 bytes with this implementation. The crash
buffer is now part of per-cpu data which makes retrieving
the crash buffer trivial.
Also now panic() will use crash reporting if
invoked from BL3-1.
FixesARM-software/tf-issues#199
Change-Id: I79d27a4524583d723483165dc40801f45e627da5
This patch introduces platform APIs to initialise and
print a character on a designated crash console.
For the FVP platform, PL011_UART0 is the designated
crash console. The platform porting guide is also updated
to document the new APIs.
Change-Id: I5e97d8762082e0c88c8c9bbb479353eac8f11a66
This patch adds baud rate and UART clock frequency as parameters
to the pl011 driver api console_init(). This allows each platform
to specify UART clock and baud rate according to their specific
hardware implementation.
FixesARM-software/tf-issues#215
Change-Id: Id13eef70a1c530e709b34dd1e6eb84db0797ced2
This patch replaces the pl011 console family of functions
with their equivalents defined in assembly. The baud rate is
defined by the PL011_BAUDRATE macro and IBRD and FBRD values
for pl011 are computed statically. This patch will enable
us to invoke the console functions without the C Runtime Stack.
Change-Id: Ic3f7b7370ded38bf9020bf746b362081b76642c7
This patch removes the allocation of memory for coherent stacks, associated
accessor function and some dead code which called the accessor function. It also
updates the porting guide to remove the concept and the motivation behind using
stacks allocated in coherent memory.
FixesARM-software/tf-issues#198
Change-Id: I00ff9a04f693a03df3627ba39727e3497263fc38
This patch adds a 'flags' parameter to each exception level specific function
responsible for enabling the MMU. At present only a single flag which indicates
whether the data cache should also be enabled is implemented. Subsequent patches
will use this flag when enabling the MMU in the warm boot paths.
Change-Id: I0eafae1e678c9ecc604e680851093f1680e9cefa
The ARM_GIC_ARCH build option was supposed to default to 2 on all
platforms. However, the default value was set in the FVP makefile
so for all other platforms it wasn't even defined.
This patch moves the default value to the main Makefile. The platform
port can then override it if needed.
Change-Id: I8e2da1cce7ffa3ed18814bbdcbcf2578101f18a6
platform_get_entrypoint() did not consider that a wakeup due to
System Reset Pin (by reading the power controller's PSYSR) requires
a cold boot. As a result, the code would execute the warm boot path
and eventually panic because entrypoint mailboxes are empty.
This patch ensures that the following wake-up reasons result in cold
boot:
- Cold Power-on
- System Reset Pin (includes reset by software)
FixesARM-software/tf-issues#217
Change-Id: I65ae0a0f7a46548b575900a5aac107d352b0e2cd
This patch re-organizes the memory layout on FVP as to give the
BL3-2 image as much memory as possible.
Considering these two facts:
- not all images need to live in memory at the same time. Once
in BL3-1, the memory used by BL1 and BL2 can be reclaimed.
- when BL2 loads the BL3-1 and BL3-2 images, it only considers the
PROGBITS sections of those 2 images. The memory occupied by the
NOBITS sections will be touched only at execution of the BL3-x
images;
Then it is possible to choose the different base addresses such that
the NOBITS sections of BL3-1 and BL3-2 overlay BL1 and BL2.
On FVP we choose to put:
- BL1 and BL3-1 at the top of the Trusted RAM, with BL3-1 NOBITS
sections overlaying BL1;
- BL3-2 at the bottom of the Trusted RAM, with its NOBITS sections
overlaying BL2;
This is illustrated by the following diagram:
0x0404_0000 ------------ ------------------
| BL1 | <= | BL3-1 NOBITS |
------------ <= ------------------
| | <= | BL3-1 PROGBITS |
------------ ------------------
| BL2 | <= | BL3-2 NOBITS |
------------ <= ------------------
| | <= | BL3-2 PROGBITS |
0x0400_0000 ------------ ------------------
New platform-specific constants have been introduced to easily check
at link time that BL3-1 and BL3-2 PROGBITS sections don't overwrite
BL1 and BL2. These are optional and the platform code is free to define
them or not. If not defined, the linker won't attempt to check
image overlaying.
FixesARM-software/tf-issues#117
Change-Id: I5981d1c3d66ee70eaac8bd052630c9ac6dd8b042
Refactor the FVP gic code in plat/fvp/fvp_gic.c to be a generic ARM
GIC driver in drivers/arm/gic/arm_gic.c. Provide the platform
specific inputs in the arm_gic_setup() function so that the driver
has no explicit dependency on platform code.
Provide weak implementations of the platform interrupt controller
API in a new file, plat/common/plat_gic.c. These simply call through
to the ARM GIC driver.
Move the only remaining FVP GIC function, fvp_gic_init() to
plat/fvp/aarch64/fvp_common.c and remove plat/fvp/fvp_gic.c
FixesARM-software/tf-issues#182
Change-Id: Iea82fe095fad62dd33ba9efbddd48c57717edd21
Changed the fvp_config array in fvp_common.c into a struct and
moved into a new optional common platform header,
include/plat/common/plat_config.h. Removed the config definitions
in fvp_def.h and updated all references to the platform config.
This makes the interface to the platform config cleaner and uses
a little less RAM.
FixesARM-software/tf-issues#180
Change-Id: I58dd7b3c150f24f7ee230a26fd57c827853ba803
There was already a rudimentary mechanism to detect whether BL1
R/W data was loaded at the top or bottom of memory. Basically,
- either BL1 was loaded at the very end of the trusted RAM
- in all other cases BL1 was considered sitting at the bottom of
the memory and the memory usage structure was updated accordingly,
potentially resulting in critical memory waste.
For instance, if BL1 R/W base address was set to
(TZRAM_END - 4096 - bl1_size), it would virtually occupy the whole
memory.
This patch improves the mechanism to detect the location of BL1
to avoid such scenarios.
Change-Id: I224a9edf0fe8d34208545d84b28b63f2bb830d03
This concept is no longer required since we now support loading of
images at fixed addresses only.
The image loader now automatically detects the position of the image
inside the current memory layout and updates the layout such that
memory fragmentation is minimised.
The 'attr' field of the meminfo data structure, which used to hold
the bottom/top loading information, has been removed. Also the 'next'
field has been removed as it wasn't used anywhere.
The 'init_bl2_mem_layout()' function has been moved out of common
code and put in BL1-specific code. It has also been renamed into
'bl1_init_bl2_mem_layout'.
FixesARM-software/tf-issues#109
Change-Id: I3f54642ce7b763d5ee3b047ad0ab59eabbcf916d
The code in the FVP port which checks the platform type and
revision information in the SYS_ID register strictly supported
only the first revision of the Base and Foundation FVPs.
The current check also does not reflect the fact that the
board revision field is 'local' to the board type (HBI field).
Support for a new Foundation model is required now, and the
checking code is relaxed to allow execution (with a diagnostic)
on unrecognised revisions of the Base and Foundation FVP.
Change-Id: I7cd3519dfb56954aafe5f52ce1fcea0ee257ba9f
Making the simple mmio_read_*() and mmio_write_*() functions inline
saves 360 bytes of code in FVP release build.
FixesARM-software/tf-issues#210
Change-Id: I65134f9069f3b2d8821d882daaa5fdfe16355e2f
This patch reworks FVP specific code responsible for determining
the entry point information for BL3-2 and BL3-3 stages when BL3-1
is configured as the reset handler.
Change-Id: Ia661ff0a6a44c7aabb0b6c1684b2e8d3642d11ec
The 'plat_print_gic_regs' macro was accessing the GICC_CTLR register
using the GICD_CTLR offset. This still generates the right code in
the end because GICD_CTLR == GICC_CTLR but this patch fixes it for
the logic of the code.
Change-Id: I7b17af50e587f07bec0e4c933e346088470c96f3
The bakery lock code currently expects the calling code to pass
the MPIDR_EL1 of the current CPU.
This is not always done correctly. Also the change to provide
inline access to system registers makes it more efficient for the
bakery lock code to obtain the MPIDR_EL1 directly.
This change removes the mpidr parameter from the bakery lock
interface, and results in a code reduction of 160 bytes for the
ARM FVP port.
FixesARM-software/tf-issues#213
Change-Id: I7ec7bd117bcc9794a0d948990fcf3336a367d543
The array of affinity nodes is currently allocated for 32 entries
with the PSCI_NUM_AFFS value defined in psci.h. This is not enough
for large systems, and will substantially over allocate the array
for small systems.
This patch introduces an optional platform definition
PLATFORM_NUM_AFFS to platform_def.h. If defined this value is
used for PSCI_NUM_AFFS, otherwise a value of two times the number
of CPU cores is used.
The FVP port defines PLATFORM_NUM_AFFS to be 10 which saves
nearly 1.5KB of memory.
FixesARM-software/tf-issues#192
Change-Id: I68e30ac950de88cfbd02982ba882a18fb69c1445
This memory is not used by the FVP port and requires an additional
4KB translation table.
This patch removes the entry from the memory map and reduces the
number of allocated translation tables.
FixesARM-software/tf-issues#196
Change-Id: I5b959e4fe92f5f892ed127c40dbe6c85eed3ed72
This patch removes the reinitialisation of memory mapped system timer
registers after a warm boot for the FVP. The system timers in FVP are
in the 'Always ON' power domain which meant the reinitialisation was
redundant and it could have conflicted with the setup the normal
world has done.
The programming of CNTACR(x) and CNTNSAR, the system timer registers,
are removed from the warm boot path with this patch.
FixesARM-software/tf-issues#169
Change-Id: Ie982eb03d1836b15ef3cf1568de2ea68a08b443e
According to documentation, the Rev field is located at bit 28 in
the V2M sysid register.
FixesARM-software/tf-issues#179
Change-Id: I2abb7bdc092ccd3f41f8962dc8d8d8e44e8dfdc3
Replace the current out-of-line assembler implementations of
the system register and system instruction operations with
inline assembler.
This enables better compiler optimisation and code generation
when accessing system registers.
FixesARM-software/tf-issues#91
Change-Id: I149af3a94e1e5e5140a3e44b9abfc37ba2324476
Current ATF uses a direct physical-to-virtual mapping, that is, a physical
address is mapped to the same address in the virtual space. For example,
physical address 0x8000_0000 is mapped to 0x8000_0000 virtual. This
approach works fine for FVP as all its physical addresses fall into 0 to
4GB range. But for other platform where all I/O addresses are 48-bit long,
If we follow the same direct mapping, we would need virtual address range
from 0 to 0x8fff_ffff_ffff, which is about 144TB. This requires a
significant amount of memory for MMU tables and it is not necessary to use
that much virtual space in ATF.
The patch is to enable mapping a physical address range to an arbitrary
virtual address range (instead of flat mapping)
Changed "base" to "base_va" and added "base_pa" in mmap_region_t and
modified functions such as mmap_add_region and init_xlation_table etc.
FixesARM-software/tf-issues#158
bl2_main() was overwriting any platform set X1 parameter for BL3-1
with the value zero.
This patch ensure that any platform set value is correctly passed
to BL3-1. The FVP port adds a check to verify this parameter is
being passed correctly.
FixesARM-software/tf-issues#173
Change-Id: Ifbcda73d3d41d2b04a4baf5614e9d2d21f1717c8
Rename the ic_* platform porting functions to plat_ic_* to be
consistent with the other functions in platform.h. Also rename
bl31_get_next_image_info() to bl31_plat_get_next_image_ep_info()
and remove the duplicate declaration in bl31.h.
Change-Id: I4851842069d3cff14c0a468daacc0a891a7ede84
Previously, the enable_mmu_elX() functions were implicitly part of
the platform porting layer since they were included by generic
code. These functions have been placed behind 2 new platform
functions, bl31_plat_enable_mmu() and bl32_plat_enable_mmu().
These are weakly defined so that they can be optionally overridden
by platform ports.
Also, the enable_mmu_elX() functions have been moved to
lib/aarch64/xlat_tables.c for optional re-use by platform ports.
These functions are tightly coupled with the translation table
initialization code.
FixesARM-software/tf-issues#152
Change-Id: I0a2251ce76acfa3c27541f832a9efaa49135cc1c
FVP specific files and functions containing the word "plat" have been
renamed to use the word "fvp" to distinguish them from the common
platform functionality and porting functions.
Change-Id: I39f9673dab3ee9c74bd18b3e62b7c21027232f7d
Some platform porting functions were in BL specific header files.
These have been moved to platform.h so that all porting functions
are in the same place. The functions are now grouped by BL.
Obsolete BL headers files have been removed.
Also, the weak declaration of the init_bl2_mem_layout() function
has been moved out the header file and into the source file
(bl_common.c) using the more succinct #pragma syntax. This
mitigates the risk of 2 weak definitions being created and the
wrong one being picked up by the compiler.
Change-Id: Ib19934939fd755f3e5a5a5bceec88da684308a83
Previously, platform.h contained many declarations and definitions
used for different purposes. This file has been split so that:
* Platform definitions used by common code that must be defined
by the platform are now in platform_def.h. The exact include
path is exported through $PLAT_INCLUDES in the platform makefile.
* Platform definitions specific to the FVP platform are now in
/plat/fvp/fvp_def.h.
* Platform API declarations specific to the FVP platform are now
in /plat/fvp/fvp_private.h.
* The remaining platform API declarations that must be ported by
each platform are still in platform.h but this file has been
moved to /include/plat/common since this can be shared by all
platforms.
Change-Id: Ieb3bb22fbab3ee8027413c6b39a783534aee474a
Currently the platform code gets to define the base address of each
boot loader image. However, the linker scripts couteract this
flexibility by enforcing a fixed overall layout of the different
images. For example, they require that the BL3-1 image sits below
the BL2 image. Choosing BL3-1 and BL2 base addresses in such a way
that it violates this constraint makes the build fail at link-time.
This patch requires the platform code to now define a limit address
for each image. The linker scripts check that the image fits within
these bounds so they don't rely anymore on the position of a given
image in regard to the others.
FixesARM-software/tf-issues#163
Change-Id: I8c108646825da19a6a8dfb091b613e1dd4ae133c
BL1 RO and RW base address used to be fixed, respectively to the first
address of the Trusted ROM and the first address of the Trusted RAM.
Introduce new platform defines to configure the BL1 RO and RW base
addresses.
Change-Id: If26616513a47798593a4bb845a4b0fb37c867cd6
At present BL3-1 has access to all of the SRAM, including
regions that are mapped as read-only and non-cacheable by other
firmware images.
This patch restricts BL3-1 to only be able to read/write from
memory used for its own data sections
Change-Id: I26cda1b9ba803d91a9eacda768f3ce7032c6db94
Conflicts:
plat/fvp/bl31_plat_setup.c
This patch adds support in the TSP for handling S-EL1 interrupts
handed over by the TSPD. It includes GIC support in its platform port,
updates various statistics related to FIQ handling, exports an entry
point that the TSPD can use to hand over interrupts and defines the
handover protocol w.r.t what context is the TSP expected to preserve
and the state in which the entry point is invoked by the TSPD.
Change-Id: I93b22e5a8133400e4da366f5fc862f871038df39
This patch introduces a set of functions which allow generic firmware
code e.g. the interrupt management framework to access the platform
interrupt controller. APIs for finding the type and id of the highest
pending interrupt, acknowledging and EOIing an interrupt and finding
the security state of an interrupt have been added. It is assumed that
the platform interrupt controller implements the v2.0 of the ARM GIC
architecture specification. Support for v3.0 of the specification for
managing interrupts in EL3 and the platform port will be added in the
future.
Change-Id: Ib3a01c2cf3e3ab27806930f1be79db2b29f91bcf