This patch enables BL2 to execute at the highest exception level
without any dependancy on TF BL1. This enables platforms which already
have a non-TF Boot ROM to directly load and execute BL2 and subsequent BL
stages without need for BL1. This is not currently possible because
BL2 executes at S-EL1 and cannot jump straight to EL3.
Change-Id: Ief1efca4598560b1b8c8e61fbe26d1f44e929d69
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
At early time, the CPU CA73 retention state has been supported on
Hikey960. Later we found the system has the hang issue and for
resolving this issue Hisilicon released new MCU firmware, but
unfortunately the new MCU firmware has side effect and results in the
CA73 CPU cannot really enter retention state and roll back to WFI state.
After discussion we cannot see the possibility to enable CA73 retention
state anymore on Hikey960, based on this conclusion we should remove
this state supporting from ARM-TF and roll back to WFI state only. We
will commit one patch to remove CA73 CPU retention state in kernel DT
binding as well.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
This reverts commit fdae60b6ba.
The commit fdae60b6ba changed the
parameter encoding for the hikey960. However that implies a DT change
in the kernel side. After submitting the DT change for upstreaming,
the backward compatibility issue and the interface change raise some
concerns from the Linux community about the issues related to kernel <->
ATF alignment. There is no way to detect a mis-alignment of those
without a deep knowledge of the ATF and the kernel. Furthermore, the
failing calls to PSCI in the idle path (because of bad parameters), will
lead to busy looping, implying: thermal issues and extra energy
consumption.
In regard of the Linux community concerns, the potential issues when the
ATF and the kernel are not aligned, it is preferable to revert the
commit.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Co-authored-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Use zynqmp_ipi APIs to access IPI registers in pm_service.
As the zynqmp_ipi APIs doesn't cover IPI buffers, the pm_ipi
in pm_service will still directly access the IPI buffers.
Signed-off-by: Wendy Liang <jliang@xilinx.com>
Previously, ZynqMP IPI in ATF is only for ZynqMP PM,
This patch is to have a ZynqMP IPI implementation to handle
both ZynqMP PM IPI requirement and IPI mailbox service requirement
which will be introduced next.
We control IPI agents registers access but not IPI buffers access in
this implementation. Each IPI mailbox user will directly access the
IPI buffers.
Signed-off-by: Wendy Liang <jliang@xilinx.com>
It is not necessary to read data from stdin. The input file name
is ripped off by -n option, anyway. I still use the redirect for
the output to specify the output file name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To allow BL31 to grow in SRAM, move TSP in TZC secured DRAM
by default.
Increase the BL31 max limit by one page.
Change-Id: Idd3479be02f0f9bafac2f275376d7db0c2015431
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
The current IO block buffer overlaps with BL2 image location.
So, BL2 may corrupt itself.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.
Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch overhauls the console API to allow for multiple console
instances of different drivers that are active at the same time. Instead
of binding to well-known function names (like console_core_init),
consoles now provide a register function (e.g. console_16550_register())
that will hook them into the list of active consoles. All console
operations will be dispatched to all consoles currently in the list.
The new API will be selected by the build-time option MULTI_CONSOLE_API,
which defaults to ${ERROR_DEPRECATED} for now. The old console API code
will be retained to stay backwards-compatible to older platforms, but
should no longer be used for any newly added platforms and can hopefully
be removed at some point in the future.
The new console API is intended to be used for both normal (bootup) and
crash use cases, freeing platforms of the need to set up the crash
console separately. Consoles can be individually configured to be active
active at boot (until first handoff to EL2), at runtime (after first
handoff to EL2), and/or after a crash. Console drivers should set a sane
default upon registration that can be overridden with the
console_set_scope() call. Code to hook up the crash reporting mechanism
to this framework will be added with a later patch.
This patch only affects AArch64, but the new API could easily be ported
to AArch32 as well if desired.
Change-Id: I35c5aa2cb3f719cfddd15565eb13c7cde4162549
Signed-off-by: Julius Werner <jwerner@chromium.org>
The current Rockchip platform code retains the "common" default panic
handler which simply hangs the system (until the watchdog kicks in, if
enabled). This is usually not a great user experience.
This patch implements a Rockchip-specific panic handler that calls the
platform's reboot implementation to reset the system.
Change-Id: I4cbe09c48f1b3f86ebdfc0108c186565f9ffc119
Signed-off-by: Julius Werner <jwerner@chromium.org>
The security properties of some IP blocks are configured to secure mode
after reset. This means these IP blocks can only be accessed by cpus
in secure state by default. These should be configured correclty as needed.
Signed-off-by: y00241285 <yyangwei.yangwei@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
After returning from SYSTEM_SUSPEND state, BL31 reconfigures the
TrustZone Controller during the boot sequence. If BL31 is placed in
TZC-secured DRAM, it will try to change the permissions of the memory it
is being executed from, causing an exception.
The solution is to disable SYSTEM_SUSPEND when the Trusted Firmware has
been compiled with ``ARM_BL31_IN_DRAM=1``.
Change-Id: I96dc50decaacd469327c6b591d07964726e58db4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Common code mustn't include ARM platforms headers.
Change-Id: Ib6e4f5a77c2d095e6e8c3ad89c89cb1959cd3043
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
ARM Power State Coordination Interface (ARM DEN 0022D) chapter
6.5 "Recommended StateID Encoding" defines the state ID which can be
used by platforms. The recommended power states can be presented by
below values; and it divides into three fields, every field has 4 bits
to present power states corresponding to core level, cluster level and
system level.
0: Run
1: Standby
2: Retention
3: Powerdown
This commit changes to use upper recommended power states definition on
Hikey960; and changes the power state validate function to check the
power state passed from kernel side.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
This patch allows non-secure bus masters to access TZC region0 as well
as the EL3 Payload itself.
Change-Id: I7e44f2673a2992920d41503fb4c57bd7fb30747a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This includes the stdint header to declare the various types used within
the file, preventing build errors with recent GCC versions.
Change-Id: I9e7e92bb31deb58d4ff2732067dd88b53124bcc9
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This port can be compiled to boot an AArch64 or AArch32 payload with the
build option `RPI3_BL33_AARCH32`.
Note: This is not a secure port of the Trusted Firmware. This port is
only meant to be a reference implementation to experiment with an
inexpensive board in real hardware.
Change-Id: Ide58114299289bf765ef1366199eb05c46f81903
Co-authored-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Pre-v8.2 platforms such as the Juno platform does not have
the Scalable Vector Extensions implemented and so the build
option ENABLE_SVE is set to zero.
This has a minor performance improvement with no functional
impact.
Change-Id: Ib072735db7a0247406f8b60e325b7e28b1e04ad1
Signed-off-by: David Cunado <david.cunado@arm.com>
The bl2_early_platform_setup() and bl2_platform_setup() were
redefined for Juno AArch32 eventhough CSS platform layer had
same definition for them. The CSS definitions definitions were
previously restricted to EL3_PAYLOAD_BASE builds and this is now
modified to include the Juno AArch32 builds as well thus
allowing us to remove the duplicate definitions in Juno platform
layer.
Change-Id: Ibd1d8c1428cc1d51ac0ba90f19f5208ff3278ab5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch fixes a couple of issues for AArch32 builds on ARM reference
platforms :
1. The arm_def.h previously defined the same BL32_BASE value for AArch64 and
AArch32 build. Since BL31 is not present in AArch32 mode, this meant that
the BL31 memory is empty when built for AArch32. Hence this patch allocates
BL32 to the memory region occupied by BL31 for AArch32 builds.
As a side-effect of this change, the ARM_TSP_RAM_LOCATION macro cannot
be used to control the load address of BL32 in AArch32 mode which was
never the intention of the macro anyway.
2. A static assert is added to sp_min linker script to check that the progbits
are within the bounds expected when overlaid with other images.
3. Fix specifying `SPD` when building Juno for AArch32 mode. Due to the quirks
involved when building Juno for AArch32 mode, the build option SPD needed to
specifed. This patch corrects this and also updates the documentation in the
user-guide.
4. Exclude BL31 from the build and FIP when building Juno for AArch32 mode. As
a result the previous assumption that BL31 must be always present is removed
and the certificates for BL31 is only generated if `NEED_BL31` is defined.
Change-Id: I1c39bbc0abd2be8fbe9f2dea2e9cb4e3e3e436a8
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
When defining different sections in linker scripts it is needed to align
them to multiples of the page size. In most linker scripts this is done
by aligning to the hardcoded value 4096 instead of PAGE_SIZE.
This may be confusing when taking a look at all the codebase, as 4096
is used in some parts that aren't meant to be a multiple of the page
size.
Change-Id: I36c6f461c7782437a58d13d37ec8b822a1663ec1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Set alignment size to 512B so finally we can get fip.bin with 512B
alignment. This can avoid stuck issue for 'fastboot' downloading
if USB driver uses DMA for data transferring.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Set alignment size to 512B so finally we can get fip.bin with 512B
alignment. This can avoid stuck issue for 'fastboot' downloading if
USB driver uses DMA for data transferring.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Factor out SPE operations in a separate file. Use the publish
subscribe framework to drain the SPE buffers before entering secure
world. Additionally, enable SPE before entering normal world.
A side effect of this change is that the profiling buffers are now
only drained when a transition from normal world to secure world
happens. Previously they were drained also on return from secure
world, which is unnecessary as SPE is not supported in S-EL1.
Change-Id: I17582c689b4b525770dbb6db098b3a0b5777b70a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Support SDEI on ARM platforms using frameworks implemented in earlier
patches by defining and exporting SDEI events: this patch defines the
standard event 0, and a handful of shared and private dynamic events.
Change-Id: I9d3d92a92cff646b8cc55eabda78e140deaa24e1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Define number of priority bits, and allocate priority levels for SDEI.
Change-Id: Ib6bb6c5c09397f7caef950c4caed5a737b3d4112
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Provide a strong definition for plat_sdei_validate_sdei_entrypoint()
which translates client address to Physical Address, and then validating
the address to be present in DRAM.
Change-Id: Ib93eb66b413d638aa5524d1b3de36aa16d38ea11
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The function arm_validate_ns_entrypoint() validates a given non-secure
physical address. This function however specifically returns PSCI error
codes.
Non-secure physical address validation is potentially useful across ARM
platforms, even for non-PSCI use cases. Therefore make this function
common by returning 0 for success or -1 otherwise.
Having made the function common, make arm_validate_psci_entrypoint() a
wrapper around arm_validate_ns_entrypoint() which only translates return
value into PSCI error codes. This wrapper is now used where
arm_validate_ns_entrypoint() was currently used for PSCI entry point
validation.
Change-Id: Ic781fc3105d6d199fd8f53f01aba5baea0ebc310
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The implementation currently supports only interrupt-based SDEI events,
and supports all interfaces as defined by SDEI specification version
1.0 [1].
Introduce the build option SDEI_SUPPORT to include SDEI dispatcher in
BL31.
Update user guide and porting guide. SDEI documentation to follow.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0054a/ARM_DEN0054A_Software_Delegated_Exception_Interface.pdf
Change-Id: I758b733084e4ea3b27ac77d0259705565842241a
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Acknowledging interrupt shall return a raw value from the interrupt
controller in which the actual interrupt ID may be encoded. Add a
platform API to extract the actual interrupt ID from the raw value
obtained from interrupt controller.
Document the new function. Also clarify the semantics of interrupt
acknowledge.
Change-Id: I818dad7be47661658b16f9807877d259eb127405
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch brings in the following fixes:
- The per-PE target data initialized during power up needs to be
flushed so as to be visible to other PEs.
- Setup per-PE target data for the primary PE as well. At present,
this was only setup for secondary PEs when they were powered on.
Change-Id: Ibe3a57c14864e37b2326dd7ab321a5c7bf80e8af
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This initial port of the Secure Partitions Manager to FVP supports BL31
in both SRAM and Trusted DRAM.
A document with instructions to build the SPM has been added.
Change-Id: I4ea83ff0a659be77f2cd72eaf2302cdf8ba98b32
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Achin Gupta <achin.gupta@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Adds weak functions for plat_report_exception, bl1_plat_prepare_exit
and plat_error_handler in AArch32 mode.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Building the UniPhier platform in parallel with TRUSTED_BOARD_BOOT=1
could fail due to non-existing directory. It might be difficult to
reproduce, but here is an easier way to trigger the problem:
$ make PLAT=uniphier TRUSTED_BOARD_BOOT=1 MBEDTLS_DIR=mbedtls certificates
OPENSSL build/uniphier/release/rot_key.pem
/bin/sh: 1: cannot create build/uniphier/release/rot_key.pem: Directory nonexistent
make: *** [build/uniphier/release/rot_key.pem] Error 2
The $(ROT_KEY) must depend on $(BUILD_PLAT) so that the build directory
is created before the key.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some platforms (for ex. UniPhier) want to create files in the very
top of the build directory. Add ${BUILD_PLAT} so such files can
depend on it.
Make existing directory targets depend on ${BUILD_PLAT} because
they are sub-directories of ${BUILD_PLAT}.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch includes various fixes for PSCI STAT functionality
relating to timestamp collection:
1. The PSCI stat accounting for retention states for higher level
power domains were done outside the locks which could lead to
spurious values in some race conditions. This is moved inside
the locks. Also, the call to start the stat accounting was redundant
which is now removed.
2. The timestamp wrap-around case when calculating residency did
not cater for AArch32. This is now fixed.
3. In the warm boot path, `plat_psci_stat_accounting_stop()` was
getting invoked prior to population of target power states. This
is now corrected.
Change-Id: I851526455304fb74ff0a724f4d5318cd89e19589
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Registered interrupts are configured in edge detection as the default
previous configuration assumed in previous code.
Not target mask required as Qemu BL31 will not send/route SGIs.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
These macros are only defined for corresponding image,
and they are undefined for other images. It means that we have
to use ifdef or defined() instead of relying on being 0 by default.
Change-Id: Iad11efab9830ddf471599b46286e1c56581ef5a7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
ARM_TSP_RAM_LOCATION_ID was defined only in AARCH64, but the macro
was also used in AARCH32, and it meant that it was taking the value 0,
which happened to equal ARM_TRUSTED_SRAM_ID.
Change-Id: If9f4dbee1a2ba15e7806f2a03305b554bd327363
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
OP-TEE dedicates the end of the Qemu secure DRAM as specific out-of-TEE
secure RAM. To support this configuration the trusted firmware should
not load OP-TEE resources in this area.
To overcome the issue, OP-TEE pageable image is now loaded 2MByte above
the secure RAM base address.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
This patch adds support for TBB to qemu. An RSA ROT keypair is generated at
build time and is included into BL1/BL2. The key and content certificates
are read over semihosting.
FixesARM-software/tf-issues#526
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
For Trusted Board Boot, BL2 needs more space to support the ECDSA
and ECDSA+RSA algorithms.
Change-Id: Ie7eda9a1315ce836dbc6d18d6588f8d17891a92d
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>
On Arm standard platforms, it runs out of SRAM space when TBB is
enabled, so the TSP default location is changed to dram when TBB
is enabled.
Change-Id: I516687013ad436ef454d2055d4e6fce06e467044
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>
These hooks are intended to allow one platform to try load
images from alternative places. There is a hook to initialize
the sequence of boot locations and a hook to pass to the next
sequence.
Change-Id: Ia0f84c415208dc4fa4f9d060d58476db23efa5b2
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Before this change, plat_secondary_cold_boot_setup reads wake up mailbox
as a byte array but through 64bit accesses on unaligned 64bit addresses.
In the other hand qemu_pwr_domain_on wakes secondary cores by writing
into a 64bit array.
This change forces the 64bit mailbox format as PLAT_QEMU_HOLD_ENTRY_SIZE
explicitly specifies it.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
This is not executable code. It should be put into .rodata instead
of .text section.
This produces more correct BL1 image when SEPARATE_CODE_AND_RODATA is
defined.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Init EDMA controller with non secure mode. A lot of peripherals are
depend on EDMA controller. But EDMA controller is in secure mode
by default. And this operation has to be executed in secure mode.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.
This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms. The
deprecated interrupt list definitions are however retained to support
legacy builds.
Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.
NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.
Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
SPIs can be routed to either a specific PE, or to any one of all
available PEs.
API documentation updated.
Change-Id: I28675f634568aaf4ea1aa8aa7ebf25b419a963ed
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The back end GIC driver converts and assigns the interrupt type to
suitable group.
For GICv2, a build option GICV2_G0_FOR_EL3 is introduced, which
determines to which type Group 0 interrupts maps to.
- When the build option is set 0 (the default), Group 0 interrupts are
meant for Secure EL1. This is presently the case.
- Otherwise, Group 0 interrupts are meant for EL3. This means the SPD
will have to synchronously hand over the interrupt to Secure EL1.
The query API allows the platform to query whether the platform supports
interrupts of a given type.
API documentation updated.
Change-Id: I60fdb4053ffe0bd006b3b20914914ebd311fc858
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
These APIs allow the GIC implementation to categorize interrupt numbers
into SPIs, PPIs, and SGIs. The default implementations for GICv2 and
GICv3 follows interrupt numbering as specified by the ARM GIC
architecture.
API documentation updated.
Change-Id: Ia6aa379dc955994333232e6138f259535d4fa087
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Document the API in separate platform interrupt controller API document.
Change-Id: If18f208e10a8a243f5c59d226fcf48e985941949
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This function implements the platform dependant part of PSCI system
reset2 for CSS platforms using SCMI.
Change-Id: I724389decab484043cadf577aeed96b349c1466d
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
The common implementation of css_scp_sys_shutdown and
css_scp_warm_reset is refactored into a new function,
css_scp_system_off() that allows the desired power state to be
specified.
The css_scp_system_off can be used in the implementation of
SYSTEM_RESET2 for PSCI v1.1.
Change-Id: I161e62354d3d75f969b8436d794335237520a9a4
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Provides GICv3 save/restore feature to arm_system_pwr_domain_resume and
arm_system_pwr_domain_save functions.
Introduce FVP PSCI power level 3 (System level) support. This is solely
done to provide example code on how to use the GICv3 save and restore
helpers.
Also make CSS GICv3 platforms power off the Redistributor on SYSTEM
SUSPEND as its state is saved and restored.
Change-Id: I0d852f3af8824edee1a17c085cf593ddd33a4e77
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Co-Authored-by: Douglas Raillard <douglas.raillard@arm.com>
Some recent enhancements to EL3 runtime firmware like support for
save and restoring GICv3 register context during system_suspend
necessitates additional data memory for the firmware. This patch
introduces support for creating a TZC secured DDR carveout for use
by ARM reference platforms. A new linker section `el3_tzc_dram` is
created using platform supplied linker script and data marked with
the attribute `arm_el3_tzc_dram` will be placed in this section.
The FVP makefile now defines the `PLAT_EXTRA_LD_SCRIPT` variable to
allow inclusion of the platform linker script by the top level BL31
linker script.
Change-Id: I0e7f4a75a6ac51419c667875ff2677043df1585d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
During system suspend, the GICv3 Distributor and Redistributor context
can be lost due to power gating of the system power domain. This means
that the GICv3 context needs to be saved prior to system suspend and
restored on wakeup. Currently the consensus is that the Firmware should
be in charge of this. See tf-issues#464 for more details.
This patch introduces helper APIs in the GICv3 driver to save and
restore the Distributor and Redistributor contexts. The GICv3 ITS
context is not considered in this patch because the specification says
that the details of ITS power management is implementation-defined.
These APIs are expected to be appropriately invoked by the platform
layer during system suspend.
FixesARM-software/tf-issues#464
Change-Id: Iebb9c6770ab8c4d522546f161fa402d2fe02ec00
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
Commit 11ad8f208d added supporting
multi-threaded CPUs on FVP platform, including modifications for
calculating CPU IDs. This patch imports the strong definition of the
same CPU ID calculation on FVP platform for TSP.
Without this patch, TSP on FVP was using the default CPU ID calculation,
which would end up being wrong on CPUs with multi-threading.
Change-Id: If67fd492dfce1f57224c9e693988c4b0f89a9a9a
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Uses the xlat tables library's Makefile instead of directly including
the source files in the Uniphier platform port.
Change-Id: I27294dd71bbf9bf3e82973c75324652b037e5bce
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
On ARM platforms, the maximum size of the address space is limited
to 32-bits as defined in arm_def.h. In order to access DRAM2, which
is defined beyond the 32-bit address space, the maximum address space
is increased to 36-bits in AArch64. It is possible to increase the
virtual space for AArch32, but it is more difficult and not supported
for now.
NOTE - the actual maximum memory address space is platform dependent
and is checked at run-time by querying the PARange field in the
ID_AA64MMFR0_EL1 register.
Change-Id: I6cb05c78a63b1fed96db9a9773faca04a5b93d67
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
mem_protect needs some kind of non-volatile memory because it has
to remember its state across reset and power down events.
The most suitable electronic part for this feature is a NVRAM
which should be only accesible from the secure world. Juno and
FVP lack such hardware and for this reason the MEM_PROTECT
functionality is implemented with Flash EEPROM memory on both
boards, even though this memory is accesible from the non-secure
world. This is done only to show a full implementation of
these PSCI features, but an actual system shouldn't use a
non-secure NVRAM to implement it.
The EL3 runtime software will write the mem_protect flag and BL2
will read and clear the memory ranges if enabled. It is done in
BL2 because it reduces the time that TF needs access to the full
non-secure memory.
The memory layout of both boards is defined using macros which
take different values in Juno and FVP platforms. Generic platform
helpers are added that use the platform specific macros to generate
a mem_region_t that is valid for the platform.
Change-Id: I2c6818ac091a2966fa07a52c5ddf8f6fde4941e9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
For Trusted Board Boot, BL1 RW section and BL2 need more space to
support the ECDSA algorithm. Specifically, PLAT_ARM_MAX_BL1_RW_SIZE
is increased on ARM platforms.
And on the Juno platform:
- BL2 size, PLAT_ARM_MAX_BL2_SIZE is increased.
- SCP_BL2 is loaded into the space defined by BL31_BASE ->
BL31_RW_BASE. In order to maintain the same size space for
SCP_BL2,PLAT_ARM_MAX_BL31_SIZE is increased.
Change-Id: I379083f918b40ab1c765da4e71780d89f0058040
Co-Authored-By: David Cunado <david.cunado@arm.com>
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>
platform_def.h doesn't need all the definitions in utils.h,
the ones in utils_def.h are enough. This patch is related
to the changes introduced by commit 53d9c9c85b.
Change-Id: I4b2ff237a2d7fe07a7230e0e49b44b3fc2ca8abe
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The type `unsigned long` is 32 bit wide in AArch32, but 64 bit wide in
AArch64. This is inconsistent and that's why we avoid using it as per
the Coding Guidelines. This patch changes all `UL` occurrences to `U`
or `ULL` depending on the context so that the size of the constant is
clear.
This problem affected the macro `BIT(nr)`. As long as this macro is used
to fill fields of registers, that's not a problem, since all registers
are 32 bit wide in AArch32 and 64 bit wide in AArch64. However, if the
macro is used to fill the fields of a 64-bit integer, it won't be able
to set the upper 32 bits in AArch32.
By changing the type of this macro to `unsigned long long` the behaviour
is always the same regardless of the architecture, as this type is
64-bit wide in both cases.
Some Tegra platform files have been modified by this patch.
Change-Id: I918264c03e7d691a931f0d1018df25a2796cc221
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Synchronize argument order between function definition and declaration
of pm_fpga_load.
FixesARM-software/tf-issues#514
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Otherwise, BL2 tries to load a BL32 image and triggers
assert(result == 0)
in
plat_get_image_source()
in hikey{960}_io_storage.c
in a debug build, or displays
ERROR: BL2: Failed to load image
in a release build.
Signed-off-by: Victor Chong <victor.chong@linaro.org>
This patch gives users control over logging messages printed from the C
code using the LOG macros defined in debug.h Users now have the ability
to reduce the log_level at run time using the tf_log_set_max_level()
function. The default prefix string can be defined by platform by
overriding the `plat_log_get_prefix()` platform API which is also
introduced in this patch.
The new log framework results in saving of some RO data. For example,
when BL1 is built for FVP with LOG_LEVEL=LOG_LEVEL_VERBOSE, resulted
in saving 384 bytes of RO data and increase of 8 bytes of RW data. The
framework also adds about 108 bytes of code to the release build of FVP.
FixesARM-software/tf-issues#462
Change-Id: I476013d9c3deedfdd4c8b0b0f125665ba6250554
Co-authored-by: Eleanor Bonnici <Eleanor.bonnici@arm.com>
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Earlier patches added errata workarounds 859972 for Cortex-A72, and
859972 for Cortex-A57 CPUs. Explicitly disable the workaround for Juno.
Also reorganize errata workaround flags.
No functional changes.
Change-Id: I3fe3745de57d77e5bf52012826d3969fe5d4844e
Signed-off-by: Eleanor Bonnici <Eleanor.bonnici@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Every CPU has its own debug module and this module is used by JTAG
debugging and coresight tracing. If without enabling it, it's easily to
introduce lockup issue when we enable debugging features.
This patch is to enable CPU debug module when power on CPU; this allows
connecting to all cores through JTAG and used by kernel coresight
driver.
Signed-off-by: Matthias Welwarsky <maw@sysgo.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
This patch does the required changes to enable CSS platforms
to build and use the SDS framework. Since SDS is always coupled with
SCMI protocol, the preexisting SCMI build flag is now renamed to
`CSS_USE_SCMI_SDS_DRIVER` which will enable both SCMI and SDS on
CSS platforms. Also some of the workarounds applied for SCMI are
now removed with SDS in place.
Change-Id: I94e8b93f05e3fe95e475c5501c25bec052588a9c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch introduces the driver for Shared-Data-Structure (SDS)
framework which will be used for communication between SCP and AP
CPU. The SDS framework is intended to replace the Boot-Over-MHU
(BOM) protocol used currently for the communication
Change-Id: Ic174291121f4e581b174cce3389d22d6435f7269
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch factors out common files required for sp_min for all CSS
platforms from the JUNO specific makefile to a the new `css_sp_min.mk`
makefile. This also allows the common build options that affect CSS
platforms to be configured in a central makefile for sp_min.
Change-Id: Ida952d8833b1aa5eda77ae0a6664a4632aeab24c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
plat_get_my_entrypoint was branching to juno_do_reset_to_aarch_32_state,
which is not supposed to return, and in case of returning it implemented
an infinite loop. The problem was that plat_get_my_entrypoint was using
"b" instead of "bl", so juno_do_reset_to_aarch_32_state was returning to
the caller of plat_get_my_entrypoint instead of stop the system with a
panic.
To avoid this problem juno_do_reset_to_aarch_32_state was modified to
call directly to plat_panic_handler if it tries to return.
Change-Id: I591cf2dd78d27d8568fb15b91366e4b3dce027b5
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
The commit 3eb2d67 optimizes the memory map for BL2 when TSP
is not present. But this also broke OP-TEE as it was reusing
the TSP mapping. This patch fixes this problem by adding a
separate mapping for OP-TEE in the BL2 memory map table.
Change-Id: I130a2ea552b7b62d8478081feb1f4ddf5292a118
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Due to a bug in the Boot ROM, the USB load API turned out not working
as expected. It is unfixable because the Boot ROM is hard-wired.
Add work around code in TF to bypass the problematic Boot ROM code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
checkpatch.pl from Linux reports tons of coding style errors and
warnings. I am just fixing under plat/socionext/uniphier/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The `KEY_ALG` variable is used to select the algorithm for key
generation by `cert_create` tool for signing the certificates. This
variable was previously undocumented and did not have a global default
value. This patch corrects this and also adds changes to derive the
value of `TF_MBEDTLS_KEY_ALG` based on `KEY_ALG` if it not set by the
platform. The corresponding assignment of these variables are also now
removed from the `arm_common.mk` makefile.
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Change-Id: I78e2d6f4fc04ed5ad35ce2266118afb63127a5a4
This patch ensures that the ARM_MAP_TSP_SEC_MEM memory region is mapped
in BL2 only if the TSPD has been included in the build. This saves one
entry in the plat_arm_mmap[] array and avoids to map extra memory when
it's not needed.
Change-Id: I6ae60822ff8f0de198145925b0b0d45355179a94
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>