TXD_INVERT_BIT or RXD_INVERT_BIT needs to be set only in case when
appropriate polarity is inverted. Otherwise these bits should be
cleared.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I8b09fab883a7b995fd72a7d8ae6233f0fa07011b
* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mapping at BLE stage
plat/marvell/armada/common/mss: use MSS SRAM in secure mode
include/drivers/marvell/mochi: add detection of secure mode
plat/marvell: fix SPD handling in dram port
marvell: drivers: move XOR0/1 DIOB from WIN 0 to 1
drivers/marvell/mochi: add support for cn913x in PCIe EP mode
drivers/marvell/mochi: add missing stream IDs configurations
plat/marvell/armada/a8k: support HW RNG by SMC
drivers/rambus: add TRNG-IP-76 driver
TX FIFO has space for 32 characters. With default UART baudrate 115200 it
takes more than 2ms to transmit all 32 characters, so wait at least 3ms
before flushing TX FIFO.
If WTMI firmware transmitted something via UART before TF-A was booted,
some characters may still wait in TX FIFO when TF-A is initializing UART
driver. So wait at least 3ms to ensure that HW has enough time to transmit
all characters waiting in TX FIFO.
This fixes an issue where sometimes characters transmitted on UART by our
custom WTMI image are lost.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I8ea4ea58e4ba3e0c0d7f47e679171b9b94442f19
Console initialization function needs to wait at least minimal specified
time. The fastest Armada 3720 CPU is 1200 MHz so increase loop delay to
wait at least for 100 us on 1200 MHz variant too. The slowest Armada 3720
CPU is 600 MHz and in this case delay loop would take just 2 times more,
which is not a problem.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I1f0b4aabd0e08b7696feec631419f7f7c7ec17d2
The delay loop executes 3 instructions. These 3 instructions are executed
in 2 processor ticks and 30000 iterations on a 600 MHz CPU should yield
approximately 100 us. This means we are waiting 2 ms, not 20 ms, for TX
FIFO to be empty.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I2cccad405bcc73cd6d1062adc0205c405c16c15f
Change CP110 XOR (DMA) to use WIN1 which is used for PCI-EP address
space only and using this window bypasses the need for translation
in the SMMU which has performance impact.
Change-Id: I98d99da59e904e6721cfa263ce44ad178a0fa956
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/20389
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Add initialization for TRNG-IP-76 driver and support SMC call
0xC200FF11 used for reading HW RNG value by secondary bootloader
software for KASLR support.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: I1d644f67457b28d347523f8a7bfc4eacc45cba68
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/32688
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
This patch does not change code, it only updates comments and macro name
for 6th bit of Status Register. So TF-A binary stay same.
6th bit of the Status Register is named TX EMPTY and is set to 1 when both
Transmitter Holding Register (THR) or Transmitter Shift Register (TSR) are
empty. It is when all characters were already transmitted.
There is also TX FIFO EMPTY bit in the Status Register which is set to 1
only when THR is empty.
In both console_a3700_core_init() and console_a3700_core_flush() functions
we should wait until both THR and TSR are empty therefore we should check
6th bit of the Status Register.
So current code is correct, just had misleading macro names and comments.
This change fixes this "documentation" issue, fixes macro name for 6th bit
of the Status Register and also updates comments.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I19e4e7f53a90bcfb318e6dd1b1249b6cbf81c4d3
Implementation is simple, just check if there is a pending character in
RX FIFO via RXRDY bit of Status Register and if yes, read it from
UART_RX_REG register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I226b6e336f44f5d0ca8dcb68e49a68e8f2f49708
Implementation is simple, just wait for the TX FIFO to be empty.
Without this patch TF-A on A3720 truncate the last line:
NOTICE: BL31: Built : 16:1
With this patch TF-A on A3720 print correctly also the last line:
NOTICE: BL31: Built : 19:03:31, Dec 23 2020
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I2f2ea42beab66ba132afdb400ca7898c5419db09
And from crash_console_flush.
We ignore the error information return by console_flush in _every_
place where we call it, and casting the return type to void does not
work around the MISRA violation that this causes. Instead, we collect
the error information from the driver (to avoid changing that API), and
don't return it to the caller.
Change-Id: I1e35afe01764d5c8f0efd04f8949d333ffb688c1
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
The polarity inversion for USB was not tested due to lack of hw design
which requires it. Currently all supported boards doesn't require USB
phy polarity inversion, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards. Enable the option for the ones that need it.
Change-Id: Ia5f2ee313a93962e94963e2dd8a759ef6d9da369
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The cp110 comphy has ability to invert RX and/or TX polarity. Polarity
depends on board design. Currently all supported boards doesn't require
SATA phy polarity invert, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards.
Change-Id: Ifd0bc6aaf8a76a0928132b197422f3193cf020d5
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
According to erratum IPCE_COMPHY-1353 the TX_IDLE bit should
be toggled in addition to the XFI/SFI PHY reset.
Change-Id: Idd2c2abfcb2f960caa01e6d69db524c2e4734f50
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Do not force non-secure access level for PIDI masters when LLC_SRAM
is enabled. The EIP197 is located on CP0 and need to access secure
SRAM in AP LLC. This requires EIP197 DMA to have AXPROT[1]=0 and not
changed when forwarded to address decoding tables.
Change-Id: I8962db94a124350c14220ba6d0364d294ae4664a
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Added ccu window to allow access to addresses
in the range [0xf100_0000, 0xf1ff_ffff].
Change-Id: I63ee68338d674114d01cd627198dc907653493e8
Signed-off-by: Alex Leibovich <alexl@marvell.com>
ERRATA ID: RES-3033912 - Internal Address Space Init state causes
a hang upon accesses to [0xf070_0000, 0xf07f_ffff]
Workaround: Boot Firmware (ATF) should configure CCU_RGF_WIN(4) to
split [0x6e_0000, 0xff_ffff] to values [0x6e_0000, 0x6f_ffff] and
[0x80_0000, 0xff_ffff] that cause accesses to the segment of
[0xf070_0000, 0xf07f_ffff] to act as RAZWI. Reuse common
work-around code for both AP806 and AP807.
Change-Id: Ia91a4802d02917d1682faa0c81571093d1687d97
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
- Fix the line address macro
- LLC invalidate and enable before ways lock for allocation
- Add support for limited SRAM size allocation
- Add SRAM RW test function
Change-Id: I1867ece3047566ddd7931bd7472e1f47fb42c8d4
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Since the AP process can be enabled on different setups, the information
about used comphy lane should be passed to AP FW. For instance:
- A8K development board uses comphy lane 2 for eth 0
- cn913x development board uses comphy lane 4 for eth 0
Change-Id: Icf001fb3eea4d9c24c09384e49844ecaf8655ad2
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Now when mg_conf_cm3 driver is present - move all relevant code there.
Change-Id: I444d9e877c450d6ee69ca3a49b547e4c3aeac0be
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
After configuring comphy to AP mode also start AP FW.
Change-Id: Ib28977d7ee643575a818ba17f69dea0b7e8e0df4
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Implement function which will allow to start AP FW.
Change-Id: Ie0fc8ad138bf56b10809cdc92d1e5e96a2aaf33f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Add llc_sram_enable() and llc_sram_disable() APIs to Marvell
cache_lls driver.
Add LLC_SRAM definition to Marvell common makefile - disabled
by the default.
Add description of LLC_SRAM flag to the build documentation.
Change-Id: Ib348e09752ce1206d29268ef96c9018b781db182
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add ccu_is_win_enabled() API for checking the CCU window
state using AP and window indexes.
Change-Id: Ib955a2cac28b2729b0a763f3bbbea28b476a2fe4
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Make all LLC-related macros to start with the same prefix
Add more LLC control registers definitions
This patch is a preparation step for LLC SRAM support
Change-Id: I0a4f0fc83e8ef35be93dd239a85f2a9f88d1ab19
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Configuring common phy selector which was missing for AP mode.
Change-Id: I15be1ba50b8aafe9094734abec139d72c18bb224
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
1) Relay only on rx training, remove parts responsible for tx training
(trx training).
2) Add extra steps e.g. preconfigure FFE before starting training.
3) Remove some unnecessary steps like RRBS31 loopback setting which
shouldn't be relevant for tx_training.
Change-Id: Ib1e8567714f9ce33578186a262c339aa4b1c51f2
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Update PLL configuration according to HW team guidelines.
Change-Id: I23cac4fb4a638e7416965a5399ce6947e08d0711
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Remove pll powerdown from pll configuration sequence to improve
stability. Remove redundant cases, which no longer exist.
Also get rid of irrelevant definition of CPU_2200_DDR_1200_RCLK_1200,
which is not used by 806/807.
Change-Id: If911e7dee003dfb9a42fafd7ffe34662f026fd23
Signed-off-by: Alex Leibovich <alexl@marvell.com>
This commit introduces two changes:
- remove hardcoded references to mci0 from the driver
- perform mci optimization for all mci interfaces
It fixes performance issues observed on cn9132 CP2.
Change-Id: I4e040cd54ff95c9134035ac89b87d8feb28e9eba
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The mci_initialize function name was misleading. The function itself
doesn't initialize MCI in general but performs MCI link tuning for
performance improvement.
Change-Id: I13094ad2235182a14984035bbe58013ebde84a7e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
By default all external CPs start with configuration address space set to
0xf200_0000. To overcome this issue, go in the loop and initialize the
CP one by one, using temporary window configuration which allows to access
each CP and update its configuration space according to decoding
windows scheme defined for each platform.
In case of cn9130 after this procedure bellow addresses will be used:
CP0 - f2000000
CP1 - f4000000
CP2 - f6000000
When the re-configuration is done there is need to restore previous
decoding window configuration(init_io_win).
Change-Id: I1a652bfbd0bf7106930a7a4e949094dc9078a981
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The AP807 uses different register offset for MCIx4 register, reflect it
in the code.
Change-Id: Ic7e44fede3c69083e8629741e7c440b1ae08c35f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
plat, include/plat) are moved to the new "armada" sub-folder.
Change-Id: Icf03356187078ad6a2e56c9870992be3ca4c9655
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
This patch enables the stream ID for the SD/MMC
controllers via dedicated unit register. Thanks to this
change it is possible to configure properly the
IOMMU in OS and use the SD/MMC interface in a guest
Virtual Machine.
Change-Id: I99cbd2c9882eb558ba01405d3d8a3e969f06e082
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I89c3ab2ed85ab941d8b38ced48474feb4aaa8b7e
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In order to access MG SRAM, the amb bridge needs to be configured which is
done in bl2 platform init.
For MG CM3, the image is only loaded to its SRAM and the CM3 itself is
left in reset. It is because the next stage bootloader (e.g. u-boot)
will trigger action which will take it out of reset when needed. This
can happen e.g. when appropriate device-tree setup (which has enabled
802.3 auto-neg) will be chosen. In other cases the MG CM3 should not be
running.
Change-Id: I816ea14e3a7174eace068ec44e3cc09998d0337e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Add support for powering off the SGMII COMPHY (on lanes 0 and 1).
This is needed sometimes on Turris Mox when using KEXEC.
There is also another benefit of a little energy saving when the given
network interface is down.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I55ae0fe3627e7cc0f65c78a00771939d8bf5399f
When USB3 is on lane 2 and indirect register access is used, the polling
at the end of the mvebu_a3700_comphy_usb3_power_on function is
incorrect.
The LOOPBACK_REG0 register should not be used at all. Instead we have to
write the LANE_STATUS1 register address (with offset
USB3PHY_LANE2_REG_BASE_OFFSET) into the indirect address register and
then we should poll indirect data register.
This fixes problems on Turris Mox, which uses lane 2 for USB3.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I968b0cccee5ddbe10a2b5614e52e52d87682aacd
This consists of ensuring that the left operand of each shift is
unsigned when the operation might overflow into the sign bit.
Change-Id: I78f386f5ac171d6e52383a3e42003e6fb3e96b57
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>
The old version of the macro is deprecated.
Commit cc5859ca19 ("Multi-console: Deprecate the
`finish_console_register` macro") provides more details.
Change-Id: I3d1cdf6496db7d8e6cfbb5804f508ff46ae7e67e
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
- Update CPU frequency on AP807 to 2GHz for SAR 0x0.
- Increase AVS to 0.88V for 2GHz clock
Change-Id: Ic945b682ab2f8543e34294bfc56c3eae2c5e0c8e
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
In Armada 8K DB boards, PCIe initialization can be executed only once
because PCIe reset performed during chip power on and it cannot be
executed via GPIO later.
This means that power on can be executed only once, when it's called
from the bootloader.
Power on:
Read bit 21 of the mode, it marks if the caller is
the bootloader or the Linux Kernel.
Power off:
Check if the comphy was already configured to PCIe, if yes,
check if the caller is bootloader, if both conditions are true
(PCIe mode and called by Linux) - skip the power-off.
In addition, fix incorrect documentation describing mode fields -
PCIe width is 3 bits, not 2.
NOTE: with this patch, please use LK4.14.76 (LK4.4.120 may not work
with it).
Change-Id: I4b929011f97a0a1869a51ba378687e78b3eca4ff
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Migrate Marvell platforms from legacy console API to
multi-console API.
Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.
The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.
The exceptions are files that are imported from other projects:
- CryptoCell driver
- dt-bindings folders
- zlib headers
Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Add support for Marvell Armada-3700 COMPHY driver
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Some of COMPHY parameters depends on the hw connection between the SoC
and the PHY, which can vary on different boards e.g. due to different
wires length. Define the "porting layer" with some defaults
parameters. It ease updating static values which needs to be updated due
to board differences, which are now grouped in one place.
Example porting layer for a8k-db is under:
plat/marvell/a8k/a80x0/board/phy-porting-layer.h
If for some boards parameters are not defined (missing
phy-porting-layer.h), the default values are used
(drivers/marvell/comphy/phy-default-porting-layer.h)
and the following compilation warning is show:
"Using default comphy params - you may need to suit them to your board".
The common COMPHY driver code is extracted in order to be shared with
future COMPHY driver for A3700 SoC platforms
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which
is also used by Allwinner.
As Mentor Graphics allows a lot of customization, the MI2CV in the two
SoC families are not compatible, and driver modifications are needed.
Extract the common code to a MI2CV driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The I2C controller found in Marvell A8K SoCs (and some older SoCs) mux
status and baudrate registers into the same address, however, it's a
vendor customization, and the original IP core by Mentor Graphics uses
two different addresses for the two registers.
Use anonymous union in the driver, in order to ease code sharing for
other SoC vendors that use this IP core (Allwinner SoCs that are newly
introduced to mainline ATF use this core).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
It turned out that resetting the RTC time register is not
necessary during initial configuration. Safely remove it
from the sequence.
Change-Id: Id2b9c7db44a8c8dbe88a7f8a21695b72a7fd78ee
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Use PF instead of PP post-fix, since it is referring to "Phase Final"
(only G3 related register had correct spelling for relevant bit).
Change-Id: Ia5a9c9c78b74b15f7f8adde2c3ef4784c513da2c
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
The biggest comphy index can be equal to 6 so there is no need to use
uint64_t for storing it.
Change-Id: I14c2b68e51678a560815963c72aed0c37068f926
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Add simple driver which allows to configure the memory controller trust
zones. It is responsible for opening mc trustzone window, with
appropriate base address, size and attributes.
Example of usage in upcoming commits.
Change-Id: I8bea17754d31451b305040ee7de331fb8db0c63f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Rename a8k_common.h to armada_common.h to keep the same header
name across all other Marvell Armada platforms.
This is especially useful since various Marvell platforms may
use common platform files and share the driver modules.
Change-Id: I7262105201123d54ccddef9aad4097518f1e38ef
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
tf_printf and tf_snprintf are now called printf and snprintf, so the
code needs to be updated.
Change-Id: Iffeee97afcd6328c4c2d30830d4923b964682d71
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Functions provided by stdio.h such as printf and sprintf are available
in the codebase, but they add a lot of code to the final image if they
are used:
- AArch64: ~4KB
- AArch32: ~2KB in T32, ~3KB in A32
tf_printf and tf_snprintf are a lot more simple, but it is preferable
to use them when possible because they are also used in common code.
Change-Id: Id09fd2b486198fe3d79276e2c27931595b7ba60e
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Add i2c driver for A8K SoC family.
Change-Id: I5932b2fce286d84fc3ad5a74c4c456001faa3196
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add COMPHY driver for usage in a runtime service.
Change-Id: I6fb42d0a099496d5699ee24684ae2b93ed35770b
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add thermal driver for A8K SoC family.
The termal unit data is used by Marvell DRAM initialization
code for optimizing the memory controller configuration
Change-Id: Iad92689fa6e4224a89d872e9aa015393abd9cf73
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add LLC (L3) cache management drivers for Marvell SoCs
AP806, AP807 and AP810
Change-Id: Ic70710f9bc5b6b48395d62212df7011e2fbb5894
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add ModularChip and MCI drivers for A8K SoC family.
ModularChip drivers include support for the internal building
blocks of Marvell ARMADA SoCs - APN806, APN807 and CP110
Change-Id: I9559343788fa2e5eb47e6384a4a7d47408787c02
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add address decoding unit drivers for Marvell SoCs.
Address decoding flow and address translation units chart
are located at docs/marvell/misc/mvebu-a8k-addr-map.txt
Change-Id: Id6ce311fa1f4f112df3adfac5d20449f495f71ed
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Pali Rohár
Manish Pandey
Ofer Heifetz
Konstantin Porotchkin
Jimmy Brisson
Grzegorz Jaszczyk
Marcin Wojtas
Alex Leibovich
Stefan Chulski
Andre Przywara
Marek Behún
Justin Chadwell
Ambroise Vincent
Antonio Nino Diaz
Christine Gharzuzi
Igal Liberman
Icenowy Zheng