This patch adds helper functions to help platforms with cluster state entry
and exit decisions.
* tegra_fc_ccplex_pgexit_lock(): lock CPU power ungate
* tegra_fc_ccplex_pgexit_unlock(): unlock CPU power ungate
* tegra_fc_is_ccx_allowed(): CCx state entry allowed on this CPU?
Change-Id: I6490d34bf380dc03ae203eb3028f61984f06931c
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch removes the error print displayed when bpmp init
fails. On platforms that do not load the bpmp firmware, this
print is seen on every cluster idle and powerdown request,
cluttering the logs.
Change-Id: I9e30007a913080406052fc32d5360ff70a019d75
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch adds support to handle secure PPIs for Tegra watchdog timers. This
functionality is currently protected by the ENABLE_WDT_LEGACY_FIQ_HANDLING
configuration variable and is only enabled for Tegra210 platforms, for now.
Change-Id: I0752ef54a986c58305e1bc8ad9be71d4a8bbd394
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
On earlier Tegra platforms, e.g. Tegra210, the watchdog timer's FIQ interrupt
is not direclty wired to the GICD. It goes to the flow controller instead, for
power state management. But the flow controller can route the FIQ to the GICD,
as a PPI, which can then get routed to the target CPU.
This patch adds routines to enable/disable routing the legacy FIQ used by
the watchdog timers, to the GICD.
Change-Id: Idd07c88c8d730b5f0e93e3a6e4fdc59bdcb2161b
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Whenever the VPR memory is resized, the GPU is put into reset first
and then the new VPR parameters are programmed to the memory controller
block. There exists a scenario, where the GPU might be out before we
program the new VPR parameters. This means, the GPU would still be
using older settings and leak secrets.
This patch puts the GPU back into reset, if it is out of reset after
resizing VPR, to mitigate this hole.
Change-Id: I38a1000e3803f80909efcb02e27da4bd46909931
Signed-off-by: Jeetesh Burman <jburman@nvidia.com>
This patch updates the secure interrupt handler to mark the interrupt
as complete in case the NS world has not registered a handler.
Change-Id: Iebe952305f7db46375303699b6150611439475df
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch adds support to the bpmp_ipc driver to allow clients to
enable/disable clocks to hardware blocks. Currently, the API only
supports SE devices.
Change-Id: I9a361e380c0bcda59f5a92ca51c86a46555b2e90
Signed-off-by: steven kao <skao@nvidia.com>
The GICD registers are 32-bits wide whereas the crash handler was reading
them as 64-bit ones. This patch fixes the code to read the GICD registers,
32-bits at a time, from the paltform's crash handler.
Change-Id: If3d6608529684ecc02be6a1b715012310813b2a4
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch adds a default implementation for the platform specific
CPU standby power handler. Tegra SoCs can override this handler
with their own implementations.
Change-Id: I91e513842f194b1e2b1defa2d833bb4d9df5f06b
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Modifying smmu macros to pass base address of smmu so that it can be
used with multiple smmus.
Added macro for combining smmu backup regs that can be used for multiple
smmus.
Change-Id: I4f3bb83d66d5df14a3b91bc82f7fc26ec8e4592e
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
This patch removes this unused config option from the Tegra186
platform makefiles.
Change-Id: Idcdf6854332a26599323a247289c2d3ce19f475f
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch removes the usage of this platform config, as it is always
enabled by all the supported platforms.
Change-Id: Ie7adb641adeb3604b177b6960b797722d60addfa
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch adds a platform setup handler that gets called after
the MMU is enabled. Platforms wanting to make use of this handler
should declare 'plat_late_platform_setup' handler in their platform
files, to override the default weakly defined handler.
Change-Id: Ibc97a2e5a24608ddea856d0bd543a9d5876f604c
Signed-off-by: Dilan Lee <dilee@nvidia.com>
There are Tegra platforms which have limited UART ports and so
all the components have to share the console. The SPE helps out
by collecting all the logs in such cases and prints them on the
shared UART port.
This patch adds a driver to communicate with the SPE driver, which
in turn provides the console.
Change-Id: Ie750520b936b8bed0ab1d876f03fc0a3490a85a3
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch includes the console driver from individual platform
makefiles and removes it from tegra_common.mk. This allows future
platforms to include consoles of their choice.
Change-Id: I7506562bfac78421a80fb6782ac8472fbef6cfb0
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Tegra SoCs currently do not have a SMMU register at address 0xFFFFFFFF.
This patch changes the search criteria, to look for this marker, to
calculate the size of the saved context.
Change-Id: I15d91945ecb78267f91c45f37985dbb2327ca3ae
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
The Tegra memctrl driver sets up the TZDRAM fence during boot and
system suspend exit. This patch provides individual platforms with
handlers to perform custom steps during TZDRAM setup.
Change-Id: Iee094d6ca189c6dd24f1147003c33c99ff3a953b
Signed-off-by: Steven Kao <skao@nvidia.com>
This patch adds support to save the system suspend entry and exit
markers to TZDRAM to help the trampoline code decide if the current
warmboot is actually an exit from System Suspend.
The Tegra186 platform handler sets the system suspend entry marker
before entering SC7 state and the trampoline flips the state back to
system resume, on exiting SC7.
Change-Id: I29d73f1693c89ebc8d19d7abb1df1e460eb5558e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch adds a helper function to get the SMMU context's offset
and uses another helper function to get the CPU trampoline offset.
These helper functions are used by the System Suspend entry sequence
to save the SMMU context and CPU reset handler to TZDRAM.
Change-Id: I95e2862fe37ccad00fa48ec165c6e4024df01147
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch returns error if BPMP initialization fails. The platform
code marks the cluster as "runnning" since we wont be able to get
it into the low power state without BPMP.
Change-Id: I86f51d478626240bb7b4ccede8907674290c5dc1
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch renames all the secure scratch registers to reflect their
usage.
This is a list of all the macros being renamed:
- SECURE_SCRATCH_RSV1_* -> SCRATCH_RESET_VECTOR_*
- SECURE_SCRATCH_RSV6 -> SCRATCH_SECURE_BOOTP_FCFG
- SECURE_SCRATCH_RSV11_* -> SCRATCH_SMMU_TABLE_ADDR_*
- SECURE_SCRATCH_RSV53_* -> SCRATCH_BOOT_PARAMS_ADDR_*
- SECURE_SCRATCH_RSV55_* -> SCRATCH_TZDRAM_ADDR_*
NOTE: Future SoCs will have to define these macros to
keep the drivers functioning.
Change-Id: Ib3ba40dd32e77b92b47825f19c420e6fdfa8b987
Signed-off-by: Steven Kao <skao@nvidia.com>
The Tegra memctrl driver sets up the TZDRAM fence during boot and
system suspend exit. This patch provides individual platforms with
handlers to perform platform specific steps, e.g. enable encryption,
save base/size to secure scratch registers.
Change-Id: Ifaa2e0eac20b50f77ec734256544c36dd511bd63
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch fixes the following MISRA violations:
Rule 8.6: Externally-linked object or function has "no" definition(s).
Rule 11.1: A cast shall not convert a pointer to a function to
any other type.
Change-Id: Ic1f6fc14c744e54ff782c6987dab9c9430410f5e
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch sanity checks the target cluster value, during core power on,
by comparing it against the maximum number of clusters supported by the
platform.
Reported by: Rohit Khanna <rokhanna@nvidia.com>
Change-Id: Ia73ccf04bd246403de4ffff6e5c99e3b00fb98ca
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
MISRA Rule 8.4, A compatible declaration shall be visible when an
object or function with external linkage is defined.
This patch adds static for local array to fix this defect.
Change-Id: I8231448bf1bc0b1e59611d7645ca983b83d5c8e3
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
This patch adds the driver to communicate with the BPMP firmware on Tegra
SoCs, starting Tegra186. BPMP firmware is responsible for clock enable/
disable requests, module resets among other things.
MRQ is short for Message ReQuest. This is the general purpose, multi channel
messaging protocol that is widely used to communicate with BPMP. This is further
divided into a common high level protocol and a peer-specific low level protocol.
The higher level protocol specifies the peer identification, channel definition
and allocation, message structure, message semantics and message dispatch process
whereas the lower level protocol defines actual message transfer implementation
details. Currently, BPMP supports two lower level protocols - Token Mail Operations
(TMO), IVC Mail Operations (IMO).
This driver implements the IMO protocol. IMO is implemented using the IVC (Inter-VM
Communication) protocol which is a lockless, shared memory messaging queue management
protocol.
The IVC peer is expected to perform the following as part of establishing a connection
with BPMP.
1. Initialize the channels with tegra_ivc_init() or its equivalent.
2. Reset the channel with tegra_ivc_channel_reset. The peer should also ensure that
BPMP is notified via the doorbell.
3. Poll until the channel connection is established [tegra_ivc_channel_notified() return
0]. Interrupt BPMP with doorbell each time after tegra_ivc_channel_notified() return
non zero.
The IPC driver currently supports reseting the GPCDMAand XUSB_PADCTL hardware blocks. In
future, more hardware blocks would be supported.
Change-Id: I52a4bd3a853de6c4fa410904b6614ff1c63df364
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch calls the 'early_init' handler earlier during boot. This
allows the platforms using Tegra186 onwards to init the BPMP interface
earlier.
Change-Id: I0d540df39de7864ce9051ebe11eca5432c462ebf
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch enables CPU access configuration register to allow
accesses to the TZRAM aperture on chips after Tegra186.
Change-Id: I0898582f8bd6fd35360ecf8ca5cee21fe35f7aab
Signed-off-by: Steven Kao <skao@nvidia.com>
MISRA Rule 21.6, The standard library input/output functions
shall not be used.
This patch removes headers that are not really needed.
Change-Id: I746138ce7ee95d7ca985d020f89b2738d997a7a2
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
This patch saves the TZDRAM_BASE value to secure RSVD55
scratch register. The warmboot code uses this register to
restore the settings on exiting System Suspend.
Change-Id: Id76175c2a7d931227589468511365599e2908411
Signed-off-by: Harvey Hsieh <hhsieh@nvidia.com>
This patch enables the '-nostdlib' flag to instruct the compiler
to not use the standard system libraries and startup files.
Change-Id: Ibf34856f7579ed686280cee19c35d08448cf921c
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch corrects the logic to read the uncore command/response bits
from the command/response values. The previous logic tapped into incorrect
bits leading to garbage counter values.
Change-Id: Ib8327ca3cb3d2086bb268e9a5366865cdf35b493
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch modifies the timeout loop to use udelay() instead of
mdelay(). This helps with the boot time on some platforms which
issue a lot of MCE calls and every mdelay adds up increasing the
boot time by a lot.
Change-Id: Ic50081b73e1cbc2714361235b5c396e294b8f752
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
MISRA Rule 8.3, All declarations of an object or function
shall use the same names and type qualifiers.
This patch removes unused function(s).
Change-Id: I90865c003d46f1dc08bfb5f4fe8a327ea42a2bb7
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
Introduce platform handlers to program the MSS settings.
This allows the current driver to scale to future chips.
Change-Id: I40a27648a1a3c73b1ce38dafddc1babb6f0b0d9b
Signed-off-by: Puneet Saxena <puneets@nvidia.com>
Signed-off-by: Krishna Reddy <vdumpa@nvidia.com>
This patch cleans the Memory controller's interrupt status
register, before exiting to the non-secure world during
cold boot. This is required as we observed that the MC's
arbitration bit is set before exiting the secure world.
Change-Id: Iacd01994d03b3b9cbd7b8a57fe7ab5b04e607a9f
Signed-off-by: Harvey Hsieh <hhsieh@nvidia.com>
This patch updates the plat_my_core_pos() and platform_get_core_pos() helper
functions to use the `PLATFORM_MAX_CPUS_PER_CLUSTER` macro to calculate the
core position.
core_pos = CoreId + (ClusterId * PLATFORM_MAX_CPUS_PER_CLUSTER)
Change-Id: Ic49f2fc7ded23bf9484c8fe104025df8884b9faf
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch moves the TZDRAM base address to SCRATCH55_LO due
to security concerns. The HI and LO address bits are packed
into SCRATCH55_LO for the warmboot firmware to restore.
SCRATCH54_HI is still being used for backward compatibility,
but would be removed eventually.
The scratch registers are populated as:
* RSV55_0 = CFG1[12:0] | CFG0[31:20]
* RSV55_1 = CFG3[1:0]
* RSV54_1 = CFG1[12:0]
Change-Id: Idc20d165d8117488010fcc8dfd946f7ad475da58
Signed-off-by: Harvey Hsieh <hhsieh@nvidia.com>
To deal with upcoming EMC periodic compensation, increase the BPMP timeout
to 2ms.
Change-Id: I8572c031168defd15504d905c4d625f44dd7fa3d
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch removes duplicate code from the CPU's power on path. The removed
code is already present as part of PSCI's power on logic.
Change-Id: I4d18a605b219570c6bf997b9e6be6e7853ebf5cd
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch enables the 'WARMBOOT_ENABLE_DCACHE_EARLY' flag to enable
D-cache early, during the CPU warmboot sequence. This flag is applicable
for platforms like Tegra, which do not require interconnect programming to
enable cache coherency.
Change-Id: Id39471cf0922799960d8f1de6e5e0d605a53f7ca
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
If ECID is valid, we can use force instantiation
otherwise, we should use reseed for random data
generation for RNG operations in SE context save
DNI because we are not keeping software save
sequence in main.
Change-Id: I73d650e6f45db17b780834b8de4c10501e05c8f3
Signed-off-by: Samuel Payne <spayne@nvidia.com>
* Previous boot loader passes Shared DRAM address
to be used by Trusted OS to dump its boot timing records
* This patch adds support to pass the parameter
to Trusted OS during cold boot
Change-Id: I9f95bb6de80b1bbd2d2d6ec42619f895d911b8ed
Signed-off-by: Akshay Sharan <asharan@nvidia.com>
This change ports the software based SE context save routines.
The software implements the context save sequence for SE/SE2 and
PKA1. The context save routine is intended to be invoked from
the ATF SC7 entry.
Change-Id: I9aa156d6e7e22a394bb10cb0c3b05fc303f08807
Signed-off-by: Marvin Hsu <marvinh@nvidia.com>
This patch adds an assert in case the dynamic memmap routine fails.
Change-Id: Idd20debbb8944340f5928c6f2cfea973a63a7b1c
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch enables prints from asserts() for release/debug builds
on all Tegra platforms.
Change-Id: Ie256437a325a7c5015a10f55aba2287a91b57bca
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch increases the MAX_MMAP_REGIONS build flag to allow
Tegra210 platforms to dynamically map multiple memory apertures
at the same time. This takes care of scenarios when we get multiple
requests to memmap memory apertures at the same time.
Change-Id: If4fe23b454e7d588e35acfbf024b9ccbb3daccc7
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
The non secure world would like to profile the boot path for
the EL3 and S-EL1 firmwares. To allow it to do that, a non-secure
DRAM region (4K) is allocated and the base address is passed to
the EL3 firmware.
This patch adds a library to allow the platform code to store the
tag:timestamp pair to the shared memory. The tegra platform code
then uses the `record` method to add timestamps.
Original change by Akshay Sharan <asharan@nvidia.com>
Change-Id: Idbbef9c83ed84a508b04d85a6637775960dc94ba
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch fixes the logic to validate if a non-secure memory address
overlaps the TZDRAM memory aperture.
Change-Id: I68af7dc6acc705d7b0ee9161c4002376077b46b1
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
MISRA Rule 10.3, the value of an expression shall not be assigned to
an object with a narrower essential type or of a different essential
type category.
The essential type of a enum member is anonymous enum, the enum member
should be casted to the right type when using it.
Both UL and ULL suffix equal to uint64_t constant in compiler
aarch64-linux-gnu-gcc, to avoid confusing, only keep U and ULL suffix
in platform code. So in some case, cast a constant to uint32_t is
necessary.
Change-Id: I1aae8cba81ef47481736e7f95f53570de7013187
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
Varun Wadekar
Jeetesh Burman
steven kao
Pritesh Raithatha
Dilan Lee
Anthony Zhou
Harvey Hsieh
Puneet Saxena
Peter De Schrijver
Samuel Payne
Marvin Hsu