N1SDP platform supports RDIMMs with ECC capability. To use the ECC
capability, the entire DDR memory space has to be zeroed out before
enabling the ECC bits in DMC620. Zeroing out several gigabytes of
memory from SCP is quite time consuming so functions are added that
zeros out the DDR memory from application processor which is
much faster compared to SCP. BL33 binary cannot be copied to DDR memory
before enabling ECC so this is also done by TF-A from IOFPGA-DDR3
memory to main DDR4 memory after ECC is enabled.
Original PLAT_PHY_ADDR_SPACE_SIZE was limited to 36-bits with which
the entire DDR space cannot be accessed as DRAM2 starts in base
0x8080000000. So these macros are redefined for all ARM platforms.
Change-Id: If09524fb65b421b7a368b1b9fc52c49f2ddb7846
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
During the secondary cores' cold boot path, the cores initialise the GIC
CPU interface. However this is a redundant action since 1) the cores are
powered down immediately after that, 2) the GIC CPU interface is
initialised from scratch when the secondary cores are powered up again
later.
Moreover, this part of code was introducing a bug. In a GICv3 system,
the GIC's CPU interface system registers must not be written without the
core being marked as "awake" in the redistributor. However, this
sequence was performing such accesses and this would cause those cores
to hang. The hang was caused by the DSB instruction that would never
complete because of the GIC not recognising those writes.
For the two aforementioned reasons, the entire part of the GIC CPU
interface initialisation is removed.
Change-Id: I6c33a1edda69dd5b6add16a27390a70731b5532a
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
Some cores support only AArch64 mode. In those cores, only a limited
subset of the AArch32 system registers are implemented. Hence, if TF-A
is supposed to run on AArch64-only cores, it must be compiled with
CTX_INCLUDE_AARCH32_REGS=0.
Currently, the default settings for compiling TF-A are with the AArch32
system registers included. So, if we compile TF-A the default way and
attempt to run it on an AArch64-only core, we only get a runtime panic.
Now a compile-time check has been added to ensure that this flag has the
appropriate value when AArch64-only cores are included in the build.
Change-Id: I298ec550037fafc9347baafb056926d149197d4c
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
* changes:
N1SDP: Initialise CNTFRQ in Non Secure CNTBaseN
N1SDP: Fix DRAM2 start address
Add option for defining platform DRAM2 base
Disable speculative loads only if SSBS is supported
The default DRAM2 base address for Arm platforms
is 0x880000000. However, on some platforms the
firmware may want to move the start address to
a different value.
To support this introduce PLAT_ARM_DRAM2_BASE that
defaults to 0x880000000; but can be overridden by
a platform (e.g. in platform_def.h).
Change-Id: I0d81195e06070bc98f376444b48ada2db1666e28
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
For security DMA should be blocked at the SMMU by default
unless explicitly enabled for a device. SMMU is disabled
after reset with all streams bypassing the SMMU, and
abortion of all incoming transactions implements a default
deny policy on reset.
This patch also moves "bl1_platform_setup()" function from
arm_bl1_setup.c to FVP platforms' fvp_bl1_setup.c and
fvp_ve_bl1_setup.c files.
Change-Id: Ie0ffedc10219b1b884eb8af625bd4b6753749b1a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch fixes this issue:
https://github.com/ARM-software/tf-issues/issues/660
The introduced changes are the following:
1) Some cores implement cache coherency maintenance operation on the
hardware level. For those cores, such as - but not only - the DynamIQ
cores, it is mandatory that TF-A is compiled with the
HW_ASSISTED_COHERENCY flag. If not, the core behaviour at runtime is
unpredictable. To prevent this, compile time checks have been added and
compilation errors are generated, if needed.
2) To enable this change for FVP, a logical separation has been done for
the core libraries. A system cannot contain cores of both groups, i.e.
cores that manage coherency on hardware and cores that don't do it. As
such, depending on the HW_ASSISTED_COHERENCY flag, FVP includes the
libraries only of the relevant cores.
3) The neoverse_e1.S file has been added to the FVP sources.
Change-Id: I787d15819b2add4ec0d238249e04bf0497dc12f3
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
This patch is a preparation for the subsequent changes in
SMMUv3 driver. It introduces a new "smmuv3_poll" function
and replaces inline functions for accessing SMMU registers
with mmio read/write operations. Also the infinite loop
for the poll has been replaced with a counter based timeout.
Change-Id: I7a0547beb1509601f253e126b1a7a6ab3b0307e7
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.
So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.
Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Improved support for W=1 compilation flag by solving missing-prototypes
and old-style-definition warnings.
The libraries are compiling with warnings (which turn into errors with
the Werror flag).
Outside of libraries, some warnings cannot be fixed without heavy
structural changes.
Change-Id: I1668cf99123ac4195c2a6a1d48945f7a64c67f16
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Fixed the below bugs:
1) Bug related to build flag V=1: if the flag was V=0, building with
ROMLIB would fail.
2) Due to a syntax bug in genwrappers.sh, index file entries marked as
"patch" or "reserved" were ignored.
3) Added a prepending hash to constants that genwrappers is generating.
4) Due to broken dependencies, currently the inclusion functionality is
intentionally not utilised. This is why the contents of romlib/jmptbl.i
have been copied to platform specific jmptbl.i files. As a result of the
broken dependencies, when changing the index files, e.g. patching
functions, a clean build is always required. This is a known issue that
will be fixed in the future.
Change-Id: I9d92aa9724e86d8f90fcd3e9f66a27aa3cab7aaa
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
When RECLAIM_INIT_CODE is 1, the stack is used to contain the .text.init
section. This is by default enable on FVP. Due to the size increase of
the .text.init section, the stack had to be adjusted contain it.
Change-Id: Ia392341970fb86c0426cf2229b1a7295453e2e32
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
This patch adds support for Versatile express FVP (Fast models).
Versatile express is a family of platforms that are based on ARM v7.
Currently this port has only been tested on Cortex A7, although it
should work with other ARM V7 cores that support LPAE, generic timers,
VFP and hardware divide. Future patches will support other
cores like Cortex A5 that dont support features like LPAE
and hardware divide. This platform is tested on and only expected to
work on single core models.
Change-Id: I10893af65b8bb64da7b3bd851cab8231718e61dd
Signed-off-by: Usama Arif <usama.arif@arm.com>
The variable is renamed to PLAT_ARM_RUN_UART as
the UART is used outside BL31 as well.
Change-Id: I00e3639dfb2001758b7d24548c11236c6335f64a
Signed-off-by: Usama Arif <usama.arif@arm.com>
Rather than letting the Trusty makefile set the option to enable dynamic
translation tables, make platforms do it themselves.
This also allows platforms to replace the implementation of the
translation tables library as long as they use the same function
prototypes.
Change-Id: Ia60904f61709ac323addcb57f7a83391d9e21cd0
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
PLAT_ARM_NS_IMAGE_OFFSET is in fact not an offset relative to some base
address, it is an absolute address. Rename it to avoid any confusion.
Change-Id: I1f7f5e8553cb267786afe7e5f3cd4d665b610d3f
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The PLAT_XLAT_TABLES_DYNAMIC build option, defined in platform_def.h
in Arm platforms, is checked by several headers, affecting their
behaviour. To avoid issues around the include ordering of the headers,
the definition should be moved to the platform's makefile.
Change-Id: I0e12365c8d66309122e8a20790e1641a4f480a10
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Use full include paths like it is done for common includes.
This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.
Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The SPM implementation based on MM is going to be kept for the
foreseeable future.
Change-Id: I11e96778a4f52a1aa803e7e048d9a7cb24a53954
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.
This also prevents problems like cyclic dependencies.
Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Update some asserts that refer to #defines that only occur in
ARM platforms, preventing this code to be used on other platforms.
Instead, use a platform agnostic name, and update all the existing
users.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The patch SHA 55cf015c enabled PIE support when RESET_TO_BL31=1 for
all ARM platforms. But it seems n1sdp platform doesn't work with PIE
support yet. Hence restrict the ENABLE_PIE=1 to fvp platform.
Change-Id: If44e42528e4b0b57c69084503f346576fe0748bd
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch allows platforms to define their
own jump table list for library at ROM. The
file has the list of functions to be used
from library at ROM. It can also include
other list files.
Change-Id: I721c35d7dad3dcadbb3a7f3277bfd5d3e1f6e00a
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
SPM needs to map a number of regions on behalf of the secure partition.
Previously, it used to get a list of them from platform code using the
plat_get_secure_partition_mmap() API. Now it gets them from the resource
description structure.
The SPM<->SP shared buffer is mapped dynamically at EL3. This buffer is
used to pass information between SPM and SP, so it must be mapped at EL3
as well in order to be used by SPM.
Dynamic translation tables have been enabled when the Trusted Firmware
is compiled with SPM support.
Change-Id: I64ad335e931661812a0a60558e60372e1e5e6b72
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Load SP and RD from package instead of relying on RD being already
loaded in memory and the SP being loaded as a BL32 image.
Change-Id: I18d4fbf4597656c6a7e878e1d7c01a8a324f3f8a
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This information is retrieved from the resource description now.
Change-Id: Iaae23945eb2c45305cdc6442853e42f4e04fe094
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This information is defined by the Secure Partition in the resource
description.
Change-Id: Ia7db90c5de8360a596106880d3f6a632a88d3ea8
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
In order to allow Arm platforms to override the default list of PSCI
callbacks, remove the existing weak implementation of
'plat_arm_psci_override_pm_ops' function and let all the Arm platforms
implement their own 'plat_arm_psci_override_pm_ops' function.
For platforms that support SCMI protocol, the function
'css_scmi_override_pm_ops' can be additionally used as well to
override the default PSCI callbacks.
Change-Id: If7c27468bd51a00ea9c2a3716b5894163f5a9f3c
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Register a priority level, PLAT_SP_PRI, for secure partition with EL3
exception handling framework(ehf) module.
The secure partition manager(SPM) would raise the core's priority to
PLAT_SP_PRI before entering the secure partition, to protect the core
from getting interrupted while in secure partition.
Change-Id: I686897f052a4371e0efa9b929c07d3ad77249e95
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.
The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.
The exceptions are files that are imported from other projects:
- CryptoCell driver
- dt-bindings folders
- zlib headers
Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch enabled PIE for FVP when RESET_TO_BL31=1. The references
to BL31_BASE are replaced by BL31_START as being a symbol exported by
the linker, will create a dynamic relocation entry in .rela.dyn and
hence will be fixed up by dynamic linker at runtime. Also, we disable
RECLAIM_INIT_CODE when PIE is enabled as the init section overlay
creates some static relocations which cannot be handled by the
dynamic linker currently.
Change-Id: I86df1b0a8b2a8bbbe7c3f3c0b9a08c86c2963ec0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch makes use of mov_imm macro where possible to load
immediate values within ARM platform layer.
Change-Id: I02bc7fbc1fa334c9fccf76fbddf515952f9a1298
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This function is not related to Arm platforms and can be reused by other
platforms if needed.
Change-Id: Ia9c328ce57ce7e917b825a9e09a42b0abb1a53e8
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
There are several platforms using arm_setup_page_tables(), which is
supposed to be Arm platform only. This creates several dependency
problems between platforms.
This patch adds the definition XLAT_TABLES_LIB_V2 to the xlat tables lib
v2 makefile. This way it is possible to detect from C code which version
is being used and include the correct header.
The file arm_xlat_tables.h has been renamed to xlat_tables_compat.h and
moved to a common folder. This way, when in doubt, this header can be
used to guarantee compatibility, as it includes the correct header based
on XLAT_TABLES_LIB_V2.
This patch also removes the usage of ARM_XLAT_TABLES_V1 from QEMU (so
that is now locked in xlat lib v2) and ZynqMP (where it was added as a
workaround).
Change-Id: Ie1e22a23b44c549603d1402a237a70d0120d3e04
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This file is shared between FVP and all CSS platforms. While it may be
true that some definitions can be common, it doesn't make sense
conceptually. For example, the stack size depends on the platform and so
does the SRAM size.
After removing them, there are not enough common definitions to justify
having this header, so the other definitions have been moved to the
platform_def.h of FVP, board_css_def.h and arm_def.h.
Change-Id: Ifbf4b017227f9dfefa1a430f67d7d6baae6a4ba1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This way it can be reused by other platforms if needed.
Note that this driver is designed to work with the Versatile Express NOR
flash of Juno and FVP. In said platforms, the memory is organized as an
interleaved memory of two chips with a 16 bit word.
Any platform that wishes to reuse it with a different configuration will
need to modify the driver so that it is more generic.
Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Map the initialization code for BL31 to overlap with the memory
required for the secondary cores stack. Once BL31 has been
initialized the memory can be remapped to RW data so that it can
be used for secondary cores stacks. By moving code from .text to
.text.init the size of the BL31 image is decreased by a page.
Split arm_common.ld.S into two linker scripts, one for tzc_dram
(arm_tzc_dram.ld.S) and one for reclaiming initialization code
(arm_reclaim_init.ld.S) so that platforms can chose which memory
regions they wish to include.
Change-Id: I648e88f3eda1aa71765744cf34343ecda9320b32
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
Mark the initialization functions found in the BL31 boot sequence
as __init so they can be reclaimed when no longer needed.
Change-Id: I687a89346419c7710ef5097feaa325d83c527697
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
This option makes it hard to optimize the memory definitions of all Arm
platforms because any change in the common defines must work in all of
them. The best thing to do is to remove it and move the definition to
each platform's header.
FVP, SGI and SGM were using the definitions in board_arm_def.h. The
definitions have been copied to each platform's platform_def.h. Juno
was already using the ones in platform_def.h, so there have been no
changes.
Change-Id: I9aecd11bbc72a3d0d7aad1ef9934d8df21dcfaf2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
- Remove references to removed build options.
- Remove support for legacy GIC driver.
- Remove support for LOAD_IMAGE_V2=0.
Change-Id: I72f8c05620bdf4a682765e6e53e2c04ca749a3d5
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch introduces the shared Mbed TLS heap optimisation for Arm
platforms. The objective is the Mbed TLS heap to be shared between BL1
and BL2 so as to not allocate the heap memory twice. To achieve that,
the patch introduces all the necessary helpers for implementing this
optimisation. It also applies it for FVP.
Change-Id: I6d85eaa1361517b7490956b2ac50f5fa0d0bb008
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
All the arm platforms were including the files related to
mem-protect. This configuration generates some problems
with new platforms that don't support such functionality,
and for that reason this patch moves these files to the
platform specific makefiles.
Change-Id: I6923e5224668b76667795d8e11723cede7979b1e
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
The SGI platforms need to allocate memory for CPER buffers. These
platform buffers would be placed between the shared reserved memory
and the per cpu stack memory, thus the need to redefine stack base
pointer for these platforms. This patch allows each board in ARM
platform to define the PLAT_SP_IMAGE_STACK_BASE.
Change-Id: Ib5465448b860ab7ab0f645f7cb278a67acce7be9
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
Set the ability to dynamically disable Trusted Boot Board
authentication to be off by default
Change-Id: Ibd2aa179179f7d9b0e7731c6e450f200a8c67529
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
The file arm_ras.c intended to provide common platform-specific RAS
configuration for Arm platforms. Because this file has symbol
definitions, it's proving difficult to provide a common definition.
This patch therefore renames and makes the file specific to FVP. Other
platforms shall provide their own configuration in similar fashion.
Change-Id: I766fd238946e3e49cdb659680e1b45f41b237901
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Having these definitions in board_arm_def.h forces to
all the arm platforms to use the same definition for
PLAT_ARM_MEM_PROT_ADDR.
This macro also enables the mem-protect mechanism,
which means that all the arm platform has enabled
mem-protect and they cannot get rid of it.
Change-Id: Id29d2c51cbe6edc15f010a9f5a20c42266c48a08
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
The upcoming patch that adds dynamic mitigation for Cortex-A76
requires that DYNAMIC_WORKAROUND_CVE_2018_3639=1. On FVP, we pull in
all the CPU files into the build which means there will be a build
failure if DYNAMIC_WORKAROUND_CVE_2018_3639=0.
Change-Id: I2e781cbeafbf5d16eaabf76a1677e0c9f81269d2
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Both Cortex-Ares and Cortex-A76 CPUs use the ARM DynamIQ Shared Unit
(DSU). The power-down and power-up sequences are therefore mostly
managed in hardware, and required software operations are simple.
Change-Id: I3a9447b5bdbdbc5ed845b20f6564d086516fa161
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>
The patch changes the layout of BL images in memory to enable
more efficient use of available space. Previously BL31 was loaded
with the expectation that BL2 memory would be reclaimed by BL32
loaded in SRAM. But with increasing memory requirements in the
firmware, we can no longer fit BL32 in SRAM anymore which means the
BL2 memory is not reclaimed by any runtime image. Positioning BL2
below BL1-RW and above BL31 means that the BL31 NOBITS can be
overlaid on BL2 and BL1-RW.
This patch also propogates the same memory layout to BL32 for AArch32
mode. The reset addresses for the following configurations are also
changed :
* When RESET_TO_SP_MIN=1 for BL32 in AArch32 mode
* When BL2_AT_EL3=1 for BL2
The restriction on BL31 to be only in DRAM when SPM is enabled
is now removed with this change. The update to the firmware design
guide for the BL memory layout is done in the following patch.
Change-Id: Icca438e257abe3e4f5a8215f945b9c3f9fbf29c9
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
BL31 is running out of space, and the use-case of SPM doesn't require it
to be in SRAM. To prevent BL31 from running out of space in the future,
move BL31 to DRAM if SPM is enabled.
Secure Partition Manager design document updated to reflect the changes.
Increased the size of the stack of BL31 for builds with SPM.
The translation tables used by SPM in Arm platforms have been moved back
to the 'xlat_tables' region instead of 'arm_el3_tzc_dram'. Everything is
in DRAM now, so it doesn't make sense to treat them in a different way.
Change-Id: Ia6136c8e108b8da9edd90e9d72763dada5e5e5dc
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.
The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.
Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.
The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.
Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.
The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.
Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp SPD=tspd all
Change-Id: I0a16cf68fef29cf00ec0a52e47786f61d02ca4ae
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.
This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>
The current AArch32 version of plat_arm_calc_core_pos uses an incorrect
algorithm to calculate the linear position of a core / PE from its
MPIDR.
This patch corrects the algorithm to:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId
which supports cores where there are more than 1 PE per CPU.
NOTE: the AArch64 version was fixed in 39b21d1
Change-Id: I72aea89d8f72f8b1fef54e2177a0fa6fef0f5513
Signed-off-by: David Cunado <david.cunado@arm.com>
x3 will be assigned by the folloing instructions.
So the first instruction is not needed any more.
old method:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER)
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId
it should be
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId
which can be simplified as:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER + CPUId) * FVP_MAX_PE_PER_CPU + ThreadId
Signed-off-by: Wang Feng <feng_feng.wang@spreadtrum.com>
The FVP platform port for SP_MIN (BL32) didn't map the flash memory
in BL32 for stroring the mem_protect enable state information leading
to synchronous exception. The patch fixes it by adding the region to
the BL32 mmap tables.
Change-Id: I37eec83c3e1ea43d1b5504d3683eebc32a57eadf
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>
Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.
In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.
Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.
Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.
The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.
FixesARM-software/tf-issues#559
Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This was correct according to the model specifications , but it seems
that FVP doesn't implement it. It is safer to use the size exposed by
the DTB which is currently used by Linux.
Change-Id: I9aabe3284a50ec2a36ed94966eb7e4ddf37cec3b
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.3: All declarations of an object or function shall
use the same names and type qualifiers.
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I48201c9ef022f6bd42ea8644529afce70f9b3f22
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
FVPs that model DynamIQ configuration implements all CPUs in a single
cluster. I.e., such models have a single cluster with more than 4 CPUs.
This differs from existing default build configuration for FVP where up
to 4 CPUs are assumed per cluster.
To allow building for DynamIQ configuration, promote the macro
FVP_MAX_CPUS_PER_CLUSTER as a build option to have it set from the build
command line. The value of the build option defaults to 4.
Change-Id: Idc3853bc95f680869b434b011c2dbd733e40c6ce
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
MISRA C-2012 Rule 7.3 violation: lowercase l shall not be used as literal suffixes.
This patch resolves this for the ULL() macro by using ULL suffix instead
of the ull suffix.
Change-Id: Ia8183c399e74677e676956e8653e82375d0e0a01
Signed-off-by: David Cunado <david.cunado@arm.com>
This patch restricts building the dynamic config DTBs to the Unix
build environment as the Device Tree compiler may not be available
on other build environments.
Change-Id: Ie690e80010a174300e966240fd977b37561156e0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch also fixes the assumption that the counters are disabled on
the resume path. This is incorrect as the AMU counters are enabled
early in the CPU reset function before `cpuamu_context_restore()`
runs.
Change-Id: I38a94eb166a523f00de18e86860434ffccff2131
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch also fixes `cpuamu_write_cpuamcntenclr_el0()` to use an MSR
instruction instead of an MRS instruction.
Change-Id: Ia6531f64b5ebc60ba432124eaa8d8eaccba40ed0
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch adds TB_FW_CONFIG for FVP and allows FVP
to select the appropriate HW_CONFIG to include in the
fip. The HW_CONFIG for FVP is selected via `FVP_HW_CONFIG_DTS`
build option. The TB_FW_CONFIG specifies the load address of
HW_CONFIG to BL2. Since currently the load address is different
between AARCH32 and AARCH64, 2 separate TB_FW_CONFIGs are
maintained for the 2 modes.
Change-Id: Ide8581e752dfa900087f5895c775073c841c0daf
Signed-Off-By: Soby Mathew <soby.mathew@arm.com>
The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :
1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.
2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.
3. The `libfdt` sources are now included when BL2 is built
4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.
5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.
6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.
Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.
Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.
Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch maps the devices in the first GB of the system address map
on the FVP into the S-EL1&0 translation regime when SPM support is
enabled. This grants the Secure Partition access to the devices in
this region, for example the memory-mapped Generic Timer device.
Change-Id: I3aeea65f859ecbe83efde2acee20c55500c451bc
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
This patch modifies the makefiles to avoid the definition
of BL1_SOURCES and BL2_SOURCES in the tbbr makefiles, and
it lets to the platform makefiles to define them if they
actually need these images. In the case of BL2_AT_EL3
BL1 will not be needed usually because the Boot ROM will
jump directly to BL2.
Change-Id: Ib6845a260633a22a646088629bcd7387fe35dcf9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.
The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:
--data cluster0.cpu0=bl2.bin@0x4001000
-C cluster0.cpu0.RVBAR=0x4001000
These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.
Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.
Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
After returning from SYSTEM_SUSPEND state, BL31 reconfigures the
TrustZone Controller during the boot sequence. If BL31 is placed in
TZC-secured DRAM, it will try to change the permissions of the memory it
is being executed from, causing an exception.
The solution is to disable SYSTEM_SUSPEND when the Trusted Firmware has
been compiled with ``ARM_BL31_IN_DRAM=1``.
Change-Id: I96dc50decaacd469327c6b591d07964726e58db4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Common code mustn't include ARM platforms headers.
Change-Id: Ib6e4f5a77c2d095e6e8c3ad89c89cb1959cd3043
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Factor out SPE operations in a separate file. Use the publish
subscribe framework to drain the SPE buffers before entering secure
world. Additionally, enable SPE before entering normal world.
A side effect of this change is that the profiling buffers are now
only drained when a transition from normal world to secure world
happens. Previously they were drained also on return from secure
world, which is unnecessary as SPE is not supported in S-EL1.
Change-Id: I17582c689b4b525770dbb6db098b3a0b5777b70a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
The function arm_validate_ns_entrypoint() validates a given non-secure
physical address. This function however specifically returns PSCI error
codes.
Non-secure physical address validation is potentially useful across ARM
platforms, even for non-PSCI use cases. Therefore make this function
common by returning 0 for success or -1 otherwise.
Having made the function common, make arm_validate_psci_entrypoint() a
wrapper around arm_validate_ns_entrypoint() which only translates return
value into PSCI error codes. This wrapper is now used where
arm_validate_ns_entrypoint() was currently used for PSCI entry point
validation.
Change-Id: Ic781fc3105d6d199fd8f53f01aba5baea0ebc310
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This initial port of the Secure Partitions Manager to FVP supports BL31
in both SRAM and Trusted DRAM.
A document with instructions to build the SPM has been added.
Change-Id: I4ea83ff0a659be77f2cd72eaf2302cdf8ba98b32
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Achin Gupta <achin.gupta@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.
This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms. The
deprecated interrupt list definitions are however retained to support
legacy builds.
Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.
NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.
Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Provides GICv3 save/restore feature to arm_system_pwr_domain_resume and
arm_system_pwr_domain_save functions.
Introduce FVP PSCI power level 3 (System level) support. This is solely
done to provide example code on how to use the GICv3 save and restore
helpers.
Also make CSS GICv3 platforms power off the Redistributor on SYSTEM
SUSPEND as its state is saved and restored.
Change-Id: I0d852f3af8824edee1a17c085cf593ddd33a4e77
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Co-Authored-by: Douglas Raillard <douglas.raillard@arm.com>
Some recent enhancements to EL3 runtime firmware like support for
save and restoring GICv3 register context during system_suspend
necessitates additional data memory for the firmware. This patch
introduces support for creating a TZC secured DDR carveout for use
by ARM reference platforms. A new linker section `el3_tzc_dram` is
created using platform supplied linker script and data marked with
the attribute `arm_el3_tzc_dram` will be placed in this section.
The FVP makefile now defines the `PLAT_EXTRA_LD_SCRIPT` variable to
allow inclusion of the platform linker script by the top level BL31
linker script.
Change-Id: I0e7f4a75a6ac51419c667875ff2677043df1585d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
During system suspend, the GICv3 Distributor and Redistributor context
can be lost due to power gating of the system power domain. This means
that the GICv3 context needs to be saved prior to system suspend and
restored on wakeup. Currently the consensus is that the Firmware should
be in charge of this. See tf-issues#464 for more details.
This patch introduces helper APIs in the GICv3 driver to save and
restore the Distributor and Redistributor contexts. The GICv3 ITS
context is not considered in this patch because the specification says
that the details of ITS power management is implementation-defined.
These APIs are expected to be appropriately invoked by the platform
layer during system suspend.
FixesARM-software/tf-issues#464
Change-Id: Iebb9c6770ab8c4d522546f161fa402d2fe02ec00
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
Commit 11ad8f208d added supporting
multi-threaded CPUs on FVP platform, including modifications for
calculating CPU IDs. This patch imports the strong definition of the
same CPU ID calculation on FVP platform for TSP.
Without this patch, TSP on FVP was using the default CPU ID calculation,
which would end up being wrong on CPUs with multi-threading.
Change-Id: If67fd492dfce1f57224c9e693988c4b0f89a9a9a
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
On ARM platforms, the maximum size of the address space is limited
to 32-bits as defined in arm_def.h. In order to access DRAM2, which
is defined beyond the 32-bit address space, the maximum address space
is increased to 36-bits in AArch64. It is possible to increase the
virtual space for AArch32, but it is more difficult and not supported
for now.
NOTE - the actual maximum memory address space is platform dependent
and is checked at run-time by querying the PARange field in the
ID_AA64MMFR0_EL1 register.
Change-Id: I6cb05c78a63b1fed96db9a9773faca04a5b93d67
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
mem_protect needs some kind of non-volatile memory because it has
to remember its state across reset and power down events.
The most suitable electronic part for this feature is a NVRAM
which should be only accesible from the secure world. Juno and
FVP lack such hardware and for this reason the MEM_PROTECT
functionality is implemented with Flash EEPROM memory on both
boards, even though this memory is accesible from the non-secure
world. This is done only to show a full implementation of
these PSCI features, but an actual system shouldn't use a
non-secure NVRAM to implement it.
The EL3 runtime software will write the mem_protect flag and BL2
will read and clear the memory ranges if enabled. It is done in
BL2 because it reduces the time that TF needs access to the full
non-secure memory.
The memory layout of both boards is defined using macros which
take different values in Juno and FVP platforms. Generic platform
helpers are added that use the platform specific macros to generate
a mem_region_t that is valid for the platform.
Change-Id: I2c6818ac091a2966fa07a52c5ddf8f6fde4941e9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
platform_def.h doesn't need all the definitions in utils.h,
the ones in utils_def.h are enough. This patch is related
to the changes introduced by commit 53d9c9c85b.
Change-Id: I4b2ff237a2d7fe07a7230e0e49b44b3fc2ca8abe
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
This patch does the required changes to enable CSS platforms
to build and use the SDS framework. Since SDS is always coupled with
SCMI protocol, the preexisting SCMI build flag is now renamed to
`CSS_USE_SCMI_SDS_DRIVER` which will enable both SCMI and SDS on
CSS platforms. Also some of the workarounds applied for SCMI are
now removed with SDS in place.
Change-Id: I94e8b93f05e3fe95e475c5501c25bec052588a9c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The commit 3eb2d67 optimizes the memory map for BL2 when TSP
is not present. But this also broke OP-TEE as it was reusing
the TSP mapping. This patch fixes this problem by adding a
separate mapping for OP-TEE in the BL2 memory map table.
Change-Id: I130a2ea552b7b62d8478081feb1f4ddf5292a118
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch ensures that the ARM_MAP_TSP_SEC_MEM memory region is mapped
in BL2 only if the TSPD has been included in the build. This saves one
entry in the plat_arm_mmap[] array and avoids to map extra memory when
it's not needed.
Change-Id: I6ae60822ff8f0de198145925b0b0d45355179a94
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The current definition of ARM_INSTANTIATE_LOCK macro includes a
semicolon, which means it's omitted where it's used. This is anomalous
for a C statement in global scope.
Fix this by removing semicolon from the definition; and where it's a
NOP, declare a file-scoped variable explicitly tagged as unused to avoid
compiler warning.
No functional changes.
Change-Id: I2c1d92ece4777e272a025011e03b8003f3543335
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
If SPD_opteed is defined map ARM_OPTEE_PAGEABLE_LOAD_MEM in bl2 to
allow loading of OP-TEE paged part.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
At present, the MPIDR validation on FVP relies on MT bit set along
with shifted affinities. This currently is additionally dependent
on the FVP model being of variant C. This however should be based
on the presence of MT bit alone.
This patch makes the change to always assume that the affinities
are shifted in the FVP model when MT bit is present.
Change-Id: I09fcb0126e1b38d29124bdeaf3450a60b95d485d
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>
Revision C of the Base FVP has the same memory map as earlier revisions,
but has the following differences:
- Implements CCI550 instead of CCI400,
- Has a single instantiation of SMMUv3,
- CPU MPIDs are shifted left by one level, and has MT bit set in them.
The correct interconnect to program is chosen at run time based on the
FVP revision. Therefore, this patch implements FVP functions for
interconnect programming, rather than depending on ARM generic ones. The
macros used have been renamed to reflect this change.
Additionally, this patch initializes SMMUv3 as part of FVP early
platform setup.
New ARM config flags are introduced for feature queries at run time.
Change-Id: Ic7b7f080953a51fceaf62ce7daa6de0573801f09
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The CCI crash dump macros assumes CCI base at build time. Since this
can't be the case for CCI on FVP, choose not to register dump CCI
registers for FVP.
Change-Id: I7374a037e7fd0a85b138e84b3cf0aa044262da97
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
ARM CPUs with multi-threading implementation has more than one
Processing Element in a single physical CPU. Such an implementation will
reflect the following changes in the MPIDR register:
- The MT bit set;
- Affinity levels pertaining to cluster and CPUs occupy one level
higher than in a single-threaded implementation, and the lowest
affinity level pertains to hardware threads. MPIDR affinity level
fields essentially appear shifted to left than otherwise.
The FVP port henceforth assumes that both properties above to be
concomitant on a given FVP platform.
To accommodate for varied MPIDR formats at run time, this patch
re-implements the FVP platform-specific functions that translates MPIDR
values to a linear indices, along with required validation. The same
treatment is applied for GICv3 MPIDR hashing function as well.
An FVP-specific build option FVP_MAX_PE_PER_CPU is introduced which
specifies the maximum number of threads implemented per CPU. For
backwards compatibility, its value defaults to 1.
Change-Id: I729b00d3e121d16ce9a03de4f9db36dfac580e3f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The DEVICE2 memory range is needed to access the Root of Trust Public
Key registers. This is not needed when Trusted Board Boot is disabled
so it's safer to not map it in this case. This also saves one level-2
page table in each of BL1 and BL2 images.
Also add some comments.
Change-Id: I67456b44f3fd5e145f6510a8499b7fdf720a7273
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
This fix modifies the order of #includes in ARM standard platforms
to meet the ARM TF coding standard.
Change-Id: Ide19aad6233babda4eea2d17d49e523645fed1b2
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>
SPE is only supported in non-secure state. Accesses to SPE specific
registers from SEL1 will trap to EL3. During a world switch, before
`TTBR` is modified the SPE profiling buffers are drained. This is to
avoid a potential invalid memory access in SEL1.
SPE is architecturally specified only for AArch64.
Change-Id: I04a96427d9f9d586c331913d815fdc726855f6b0
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
On ARM platforms before exiting from SP_MIN ensure that
the default console is switched to the runtime serial port.
Change-Id: I0ca0d42cc47e345d56179eac16aa3d6712767c9b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
ARM GIC-600 IP complies with ARM GICv3 architecture, but among others,
implements a power control register in the Redistributor frame. This
register must be programmed to mark the frame as powered on, before
accessing other registers in the frame. Rest of initialization sequence
remains the same.
The driver provides APIs for Redistributor power management, and
overrides those in the generic GICv3 driver. The driver data is shared
between generic GICv3 driver and that of GIC-600.
For FVP platform, the GIC-600 driver is chosen when FVP_USE_GIC_DRIVER
is set to FVP_GIC600. Also update user guide.
Change-Id: I321b2360728d69f6d4b0a747b2cfcc3fe5a20d67
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Both Cortex-A75 and Cortex-A55 CPUs use the ARM DynamIQ Shared Unit
(DSU). The power-down and power-up sequences are therefore mostly
managed in hardware, and required software operations are considerably
simpler.
Change-Id: I68b30e6e1ebe7c041d5e67f39c59f08575fc7ecc
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The default case is impossible to hit as the `power_level`
is already checked earlier. Avoids a clang warning.
Change-Id: I707463c843adc748ee9aa1d2313f9ab7dab3a8ab
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>