The Arm Generic Timer specification mandates that the
interrupt associated with each timer is low level triggered,
see:
Arm Cortex-A76 Core:
"Each timer provides an active-LOW interrupt output to the SoC."
Arm Cortex-A53 MPCore Processor:
"It generates timer events as active-LOW interrupt outputs and
event streams."
The following files in fdts\
fvp-base-gicv3-psci-common.dtsi
fvp-base-gicv3-psci-aarch32-common.dtsi
fvp-base-gicv2-psci-aarch32.dts
fvp-base-gicv2-psci.dts
fvp-foundation-gicv2-psci.dts
fvp-foundation-gicv3-psci.dts
describe interrupt types as edge rising
IRQ_TYPE_EDGE_RISING = 0x01:
interrupts = <1 13 0xff01>,
<1 14 0xff01>,
<1 11 0xff01>,
<1 10 0xff01>;
, see include\dt-bindings\interrupt-controller\arm-gic.h:
which causes Linux to generate the warnings below:
arch_timer: WARNING: Invalid trigger for IRQ5, assuming level low
arch_timer: WARNING: Please fix your firmware
This patch adds GIC_CPU_MASK_RAW macro definition to
include\dt-bindings\interrupt-controller\arm-gic.h,
modifies interrupt type to IRQ_TYPE_LEVEL_LOW and
makes use of type definitions in arm-gic.h.
Change-Id: Iafa2552a9db85a0559c73353f854e2e0066ab2b9
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
By default the Arm Ethos-N NPU will boot up in secure mode. In this mode
the non-secure world cannot access the registers needed to use the NPU.
To still allow the non-secure world to use the NPU, a SiP service has
been added that can delegate non-secure access to the registers needed
to use it.
Only the HW_CONFIG for the Arm Juno platform has been updated to include
the device tree for the NPU and the platform currently only loads the
HW_CONFIG in AArch64 builds.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I65dfd864042ed43faae0a259dcf319cbadb5f3d2
To make it possible to use the hw_config device tree for dynamic
configuration in BL31 on the Arm Juno platform. A placeholder hw_config
has been added that is included in the FIP and a Juno specific BL31
setup has been added to populate fconf with the hw_config.
Juno's BL2 setup has been updated to align it with the new behavior
implemented in the Arm FVP platform, where fw_config is passed in arg1
to BL31 instead of soc_fw_config. The BL31 setup is expected to use the
fw_config passed in arg1 to find the hw_config.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: Ib3570faa6714f92ab8451e8f1e59779dcf19c0b6
The number of ITS have changed from 4 to 1, resulting
in GICR base address change.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Change-Id: I28101f0d1faf9f3c58591b642033c3fd49a275e7
This allows Matterhorn cores to operate at their optimal OPPs.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Change-Id: I2e1b784da10154a1f1f65dd0e3a39213e7683116
Increase the core count and add respective entries in DTS.
Add Klein assembly file to cpu sources for core initialization.
Add SCMI entries for cores.
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>
Change-Id: I14dc1d87df6dcc8d560ade833ce1f92507054747
The value of stdout-path is a string and as a result, we can't use a
label as a reference to the serial0 node. This change fixes the
stdout-path property for N1SDP, Morello and TC0 by pointing to the
right alias.
Signed-off-by: Nikos Nikoleris <nikos.nikoleris@arm.com>
Change-Id: I3d403389a424569be56327fab4140fec06f96d37
The Linux Automation MC-1 is a SBC built around the Octavo Systems
OSD32MP15x SiP. The SiP features up to 1 GB DDR3 RAM, EEPROM and
PMIC. The board has eMMC and a SD slot for storage.
The SDRAM calibration values are taken as is from the DKx boards, which
seem to be suitable for operation at German room temperature.
This is deemed ok for now, but for use in the field, the SiP will likely
need to have its timings determined in a climate chamber.
Change-Id: I5f43a61930151ae9d1df2ea7d0f6f9697c813ce0
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Add reserved-memory region for OP-TEE and mark as no-map. This memory
region is used by OP-TEE as non-secure shared RAM.
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Change-Id: I5a22999a8c5550024d0f47e848d35924017df245
This patch adds support to enable OP-TEE as S-EL1 SP with SPMC at S-EL2
- create SPMC manifest file with OP-TEE as SP
- add support for ARM_SPMC_MANIFEST_DTS build option
- add optee entry with ffa as method in tc0.dts
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Change-Id: Ia9b5c22c6f605d3886914bbac8ac45e8365671cb
Specify peripherals accessed by OP-TEE as a Secure Partition
running as a VM managed by the SPMC.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Icf9aae038e2b1b0ce4696f78ff964bfff8a1498c
This is not a standard string that any kernel recognises, nor do any of
the FDTs embedded in kernels specify this, nor does QEMU's virt machine.
Whilst its presence does no harm, it's not a thing code should consult
as a result, and so drop it in order to not cause confusion and risk
incorrect code being written to search for it.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Change-Id: Iea3214a23181c54e600cf8f4f12dfc822140c23d
- Reserve 32MB below ARM_AP_TZC_DRAM1_BASE for TC0_TZC_DRAM1
- Add TC0_NS_DRAM1 base and mapping
- Reserve memory region in tc0.dts
Change-Id: If2431f7f68e4255e28c86a0e89637dab7c424a13
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Without this node, the board fails to boot and panics in the function
stm32mp_init_auth().
Change-Id: Ia54924410dac2a8c94dd6e45d7e93977fe7d87e2
Signed-off-by: Yann Gautier <yann.gautier@st.com>
FMC node bindings are modified to add EBI controller node.
FMC driver and associated device tree files are modified
to support these new bindings.
Change-Id: I4bf201e96a1aca20957e0dac3a3b87caadd05bdc
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
* changes:
arm_fpga: Add platform documentation
arm_fpga: Add post-build linker script
arm_fpga: Add ROM trampoline
arm_fpga: Add devicetree file
arm_fpga: Remove SPE PMU DT node if SPE is not available
arm_fpga: Adjust GICR size in DT to match number of cores
fdt: Add function to adjust GICv3 redistributor size
drivers: arm: gicv3: Allow detecting number of cores
The FPGA images used in Arm Ltd. focus on CPU cores, so they share a
common platform, with a minimal set of peripherals (interconnect, GIC,
UART).
This allows to support most platforms with a single devicetree file.
The topology and number of CPU cores differ, but those will added at
runtime, in BL31. Other adjustments (GICR size, SPE node, command line)
are also done at this point.
Add the common devicetree file to TF-A's build system, so it can be
build together with BL31. At runtime, the resulting .dtb file should be
uploaded to the address given with FPGA_PRELOADED_DTB_BASE at build time.
Change-Id: I3206d6131059502ec96896e95329865452c9d83e
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There is one dtsi file per SoC version:
- STM32MP151: common part for all version, Single Cortex-A7
- STM32MP153: Dual Cortex-A7
- STM32MP157: + GPU and DSI, but not needed for TF-A
The STM32MP15xC include a cryptography peripheral, add it in a dedicated
file.
There are 4 packages available, for which the IOs number change. Have one
file for each package. The 2 packages AB and AD are added.
STM32157A-DK1 and STM32MP157C-DK2 share most of their features, a common
dkx file is then created.
Some reordering is done in other files, and realign with kernel DT files.
The DDR files are generated with our internal tool, no changes in the
registers values.
Change-Id: I9f2ef00306310abe34b94c2f10fc7a77a10493d1
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This change replaces hdlcd with DPU in dts file for TC0
Change-Id: If25dfd3ddffc07279ab487f65e1bb82b27a26604
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>
Add USB IP node as the MPS3 board has the NXP isp1763 host controller.
Change-Id: I47c57e4c8345d244c46895b52fcaecc1c6f1b504
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: lakshmi Kailasanathan <lakshmi.Kailasanathan@arm.com>
Created a header file defining the id of the various nv-counters
used in the system.
Also, updated the device tree to add 'id' property for the trusted
and non-trusted nv-counters.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ia41a557f7e56ad4ed536aee11c7a59e078ae07c0
This includes both cpu and cluster sleep parameters.
Change-Id: I6a9e90b88508d6d2acd2538007cbbdd1cf976442
Signed-off-by: Usama Arif <usama.arif@arm.com>
The pl180 mmc uses 3.3V fixed regulator and vexpress
sysreg for card detection and write protect.
Change-Id: I2513cfcb97217e282a081a700f3a9f723e8207ff
Signed-off-by: Usama Arif <usama.arif@arm.com>
Currently only single signing domain is supported for SP packages but
there is plan to support dual signing domains if CoT is dualroot.
SP_CONTENT_CERT_ID is the certificate file which is currently generated
and signed with trusted world key which in-turn is derived from Silicon
provider RoT key.
To allow dual signing domain for SP packages, other certificate file
will be derived from Platform owned RoT key.
This patch renames "SP_CONTENT_CERT_ID" to "SIP_SP_CONTENT_CERT_ID" and
does other related changes.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I0bc445a3ab257e2dac03faa64f46e36a9fed5e93
Provide manifest and build options to boot OP-TEE as a
guest S-EL1 Secure Partition on top of Hafnium in S-EL2.
Increase ARM_SP_MAX_SIZE to cope with OP-TEE debug build image.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Idd2686fa689a78fe2d05ed92b1d23c65e2edd4cb
Added CoT descriptor nodes and properties in device tree.
Currently, CoT descriptors which are used by BL2 are added as part
of device tree.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Iff23cff843e5489fac18bcee5f5d6a71de5ad0d0
This patch performs the following:
- Creating two corstone700 platforms under corstone700 board:
fvp and fpga
- Since the FVP and FPGA have IP differences, this commit provides a specific DTS for each platform
- The platform can be specified using the TARGET_PLATFORM Makefile variable
(possible values are: fvp or fpga)
- Allowing to use u-boot by:
- Enabling NEED_BL33 option
- Fixing non-secure image base: For no preloaded bl33 we want to
have the NS base set on shared ram. Setup a memory map region
for NS in shared map and set the bl33 address in the area.
- Setting the SYS_COUNTER_FREQ_IN_TICKS based on the selected
platform
- Setting ARM_MAP_SHARED_RAM and ARM_MAP_NS_SHARED_RAM to use MT_MEMORY
Change-Id: I4c8ac3387acb1693ab617bcccab00d80e340c163
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Using the fconf framework, the Group 0 and Group 1 secure interrupt
descriptors are moved to device tree and retrieved in runtime. This
feature is enabled by the build flag SEC_INT_DESC_IN_FCONF.
Change-Id: I360c63a83286c7ecc2426cd1ff1b4746d61e633c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Add a node for the ETZPC device so that driver initializes during
stm32mp15* boot sequence.
Change-Id: I84bf10572e5df7b8f450163c79bcfe6956fc838f
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
This patch adds support for Total Compute (TC0) platform. It is an
initial port and additional features are expected to be added later.
TC0 has a SCP which brings the primary Cortex-A out of reset
which starts executing BL1. TF-A optionally authenticates the SCP
ram-fw available in FIP and makes it available for SCP to copy.
Some of the major features included and tested in this platform
port include TBBR, PSCI, MHUv2 and DVFS.
Change-Id: I1675e9d200ca7687c215009eef483d9b3ee764ef
Signed-off-by: Usama Arif <usama.arif@arm.com>
This patch adds support for passing FVP platform's topology
configuration to DTS files for compilation, which allows to
build DTBs with correct number of clusters and CPUs.
This removes non-existing clusters/CPUs from the compiled
device tree blob and fixes reported Linux errors when trying
to power on absent CPUs/PEs.
If DTS file is passed using FVP_HW_CONFIG_DTS build option from
the platform's makefile, FVP_CLUSTER_COUNT, FVP_MAX_CPUS_PER_CLUSTER
and FVP_MAX_PE_PER_CPU parameters are used, otherwise CI script will
use the default values from the corresponding DTS file.
Change-Id: Idcb45dc6ad5e3eaea18573aff1a01c9344404ab3
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch introduces dynamic configuration for SDEI setup and is supported
when the new build flag SDEI_IN_FCONF is enabled. Instead of using C arrays
and processing the configuration at compile time, the config is moved to
dts files. It will be retrieved at runtime during SDEI init, using the fconf
layer.
Change-Id: If5c35a7517ba00a9f258d7f3e7c8c20cee169a31
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Co-authored-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
A5DS FPGA system timer clock frequency is 7.5Mhz.
The dt is file updated inline with the hardware
clock frequency.
Change-Id: I3f6c2e0d4a7b293175a42cf398a8730448504af9
Signed-off-by: lakshmi Kailasanathan <lakshmi.Kailasanathan@arm.com>
In the context of enabling initramfs this change makes
the kernel arguments compatible with the initramfs requirements
Change-Id: Ifa955a5790ae1398fd8ad9ca1c8272f019c121a6
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Create, register( and implicitly invoke) fconf_populate_topology()
function which extracts the topology related properties from dtb into
the newly created fconf based configuration structure 'soc_topology'.
Appropriate libfdt APIs are added to jmptbl.i file for use with USE_ROMLIB
build feature.
A new property which describes the power domain levels is added to the
HW_CONFIG device tree source files.
This patch also fixes a minor bug in the common device tree file
fvp-base-gicv3-psci-dynamiq-common.dtsi
As this file includes fvp-base-gicv3-psci-common.dtsi, it is necessary
to delete all previous cluster node definitons because DynamIQ based
models have upto 8 CPUs in each cluster. If not deleted, the final dts
would have an inaccurate description of SoC topology, i.e., cluster0
with 8 or more core nodes and cluster1 with 4 core nodes.
Change-Id: I9eb406da3ba4732008a66c01afec7c9fa8ef59bf
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
This change is to add ethernet and voltage regulator nodes into
a5ds devicetree.
Change-Id: If9ed67040d54e76af1813c9f99835f51f617e9df
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Alexei Fedorov
Mikael Olsson
Usama Arif
sah01
Avinash Mehta
André Przywara
Nikos Nikoleris
Ahmad Fatoum
Arunachalam Ganapathy
Olivier Deprez
Jessica Clarke
Yann Gautier
Christophe Kerello
Jagadeesh Ujja
Madhukar Pappireddy
Manoj Kumar
Sayanta Pattanayak
Manish Pandey
Rui Miguel Silva
Manish V Badarkhe
Abdellatif El Khlifi
Etienne Carriere
Balint Dobszay
lakshmi Kailasanathan
Vishnu Banavath