The watchdog is configured with a default value of 256 seconds in order
to implement the Trusted Board Boot Requirements.
For the FVP and Juno platforms, the FWU process relies on a watchdog
reset. In order to automate the test of FWU, the length of this process
needs to be as short as possible. Instead of waiting for those 4 minutes
to have a reset by the watchdog, tell it to reset immediately.
There are no side effects as the value of the watchdog's load register
resets to 0xFFFFFFFF.
Tested on Juno.
Change-Id: Ib1aea80ceddc18ff1e0813a5b98dd141ba8a3ff2
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
N1SDP platform supports RDIMMs with ECC capability. To use the ECC
capability, the entire DDR memory space has to be zeroed out before
enabling the ECC bits in DMC620. Zeroing out several gigabytes of
memory from SCP is quite time consuming so functions are added that
zeros out the DDR memory from application processor which is
much faster compared to SCP. BL33 binary cannot be copied to DDR memory
before enabling ECC so this is also done by TF-A from IOFPGA-DDR3
memory to main DDR4 memory after ECC is enabled.
Original PLAT_PHY_ADDR_SPACE_SIZE was limited to 36-bits with which
the entire DDR space cannot be accessed as DRAM2 starts in base
0x8080000000. So these macros are redefined for all ARM platforms.
Change-Id: If09524fb65b421b7a368b1b9fc52c49f2ddb7846
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
The default DRAM2 base address for Arm platforms
is 0x880000000. However, on some platforms the
firmware may want to move the start address to
a different value.
To support this introduce PLAT_ARM_DRAM2_BASE that
defaults to 0x880000000; but can be overridden by
a platform (e.g. in platform_def.h).
Change-Id: I0d81195e06070bc98f376444b48ada2db1666e28
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.
So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.
Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Improved support for W=1 compilation flag by solving missing-prototypes
and old-style-definition warnings.
The libraries are compiling with warnings (which turn into errors with
the Werror flag).
Outside of libraries, some warnings cannot be fixed without heavy
structural changes.
Change-Id: I1668cf99123ac4195c2a6a1d48945f7a64c67f16
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
On ARM platforms, the BL2 memory can be overlaid by BL31/BL32. The memory
descriptors describing the list of executable images are created in BL2
R/W memory, which could be possibly corrupted later on by BL31/BL32 due
to overlay. This patch creates a reserved location in SRAM for these
descriptors and are copied over by BL2 before handing over to next BL
image.
Also this patch increases the PLAT_ARM_MAX_BL2_SIZE for juno when TBBR
is enabled.
FixesARM-Software/tf-issues#626
Change-Id: I755735706fa702024b4032f51ed4895b3687377f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
The SPM implementation based on MM is going to be kept for the
foreseeable future.
Change-Id: I11e96778a4f52a1aa803e7e048d9a7cb24a53954
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.
This also prevents problems like cyclic dependencies.
Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Update some asserts that refer to #defines that only occur in
ARM platforms, preventing this code to be used on other platforms.
Instead, use a platform agnostic name, and update all the existing
users.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The patch SHA 55cf015c enabled PIE support when RESET_TO_BL31=1 for
all ARM platforms. But it seems n1sdp platform doesn't work with PIE
support yet. Hence restrict the ENABLE_PIE=1 to fvp platform.
Change-Id: If44e42528e4b0b57c69084503f346576fe0748bd
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Even though this is not used unless SPD=tspd, only defining it when
SPD_tspd is defined doesn't have any advantage and it makes it harder to
read the code.
Change-Id: I3d93135e05f39be071d16f8a47394a9a3ff54bc8
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch defines BL31_BASE to 0x0 when RESET_TO_BL31=1 as the
executable is built with PIE support and can be loaded anywhere
in SRAM for execution.
Change-Id: I4007f4626322f1200a6304c9c565987d3357986c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This buffer is where all the responses from Secure Partitions are stored
until they are requested.
Change-Id: Iafeb8f0848c5ff6f3e187060cd3a47702484dc45
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Introduce SMCs that open and close handles according to the SPCI
specification.
Change-Id: I65f365f15612e01aa445e783e96e48ae275c39fd
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Load SP and RD from package instead of relying on RD being already
loaded in memory and the SP being loaded as a BL32 image.
Change-Id: I18d4fbf4597656c6a7e878e1d7c01a8a324f3f8a
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This information is retrieved from the resource description now.
Change-Id: Iaae23945eb2c45305cdc6442853e42f4e04fe094
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Introduce helpers to create resource description struct, as well as code
to load the information from DTB files.
Change-Id: I0f5bb94eb8b01c6cb53fe807a9db0c05a70d7a43
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
For platforms using multi-threaded CPUs, there can be upto four
platform power domain levels. At present, there are three platform
power domain levels that are defined for the CSS platforms. Define a
fourth level 'ARM_PWR_LVL3' as well to provide support for an
additional platform power domain level.
Change-Id: I40cc17a10f4690a560776f504364fd7277a7e72a
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.
The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.
The exceptions are files that are imported from other projects:
- CryptoCell driver
- dt-bindings folders
- zlib headers
Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
On AArch32, ARM_DRAM1_BASE and ARM_DRAM1_SIZE constants are currently
32-bit values (because they are suffixed with UL and the value
0x80000000 fits in a unsigned long int, i.e. a 32-bit value). When
summing them up, the result overflows the maximum value that can be
encoded in a 32-bit value so it wraps around and does not result in
the expected value.
This patch changes the suffix of these constants into ULL so that they
always are 64-bit values.
Change-Id: I3b19b1805e35cc7e43050458df379081b1e882d5
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
This function is not related to Arm platforms and can be reused by other
platforms if needed.
Change-Id: Ia9c328ce57ce7e917b825a9e09a42b0abb1a53e8
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
There are several platforms using arm_setup_page_tables(), which is
supposed to be Arm platform only. This creates several dependency
problems between platforms.
This patch adds the definition XLAT_TABLES_LIB_V2 to the xlat tables lib
v2 makefile. This way it is possible to detect from C code which version
is being used and include the correct header.
The file arm_xlat_tables.h has been renamed to xlat_tables_compat.h and
moved to a common folder. This way, when in doubt, this header can be
used to guarantee compatibility, as it includes the correct header based
on XLAT_TABLES_LIB_V2.
This patch also removes the usage of ARM_XLAT_TABLES_V1 from QEMU (so
that is now locked in xlat lib v2) and ZynqMP (where it was added as a
workaround).
Change-Id: Ie1e22a23b44c549603d1402a237a70d0120d3e04
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The definitions FAIL_CONTROL_*_SHIFT were incorrect, they have been
fixed.
The types tzc_region_attributes_t and tzc_action_t have been removed and
replaced by unsigned int because it is not allowed to do logical
operations on enums.
Also, fix some address definitions in arm_def.h.
Change-Id: Id37941d76883f9fe5045a5f0a4224c133c504d8b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
When HW_ASSISTED_COHERENCY is enabled we can use spinlocks
instead of using the more complex and slower bakery algorithm.
Change-Id: I9d791a70050d599241169b9160a67e57d5506564
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This file is shared between FVP and all CSS platforms. While it may be
true that some definitions can be common, it doesn't make sense
conceptually. For example, the stack size depends on the platform and so
does the SRAM size.
After removing them, there are not enough common definitions to justify
having this header, so the other definitions have been moved to the
platform_def.h of FVP, board_css_def.h and arm_def.h.
Change-Id: Ifbf4b017227f9dfefa1a430f67d7d6baae6a4ba1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Map the initialization code for BL31 to overlap with the memory
required for the secondary cores stack. Once BL31 has been
initialized the memory can be remapped to RW data so that it can
be used for secondary cores stacks. By moving code from .text to
.text.init the size of the BL31 image is decreased by a page.
Split arm_common.ld.S into two linker scripts, one for tzc_dram
(arm_tzc_dram.ld.S) and one for reclaiming initialization code
(arm_reclaim_init.ld.S) so that platforms can chose which memory
regions they wish to include.
Change-Id: I648e88f3eda1aa71765744cf34343ecda9320b32
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
- Remove references to removed build options.
- Remove support for legacy GIC driver.
- Remove support for LOAD_IMAGE_V2=0.
Change-Id: I72f8c05620bdf4a682765e6e53e2c04ca749a3d5
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The patch 7b56928 unified the FWU mechanism on FVP and Juno
platforms due to issues with MCC firmware not preserving the
NVFLAGS. With MCCv150 firmware, this issue is resolved. Also
writing to the NOR flash while executing from the same flash
in Bypass mode had some stability issues. Hence, since the
MCC firmware issue is resolved, this patch reverts to the
NVFLAGS mechanism to detect FWU. Also, with the introduction
of SDS (Shared Data Structure) by the SCP, the reset syndrome
needs to queried from the appropriate SDS field.
Change-Id: If9c08f1afaaa4fcf197f3186887068103855f554
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
Signed-off-by: Soby Mathew <Soby.Mathew@arm.com>
This patch introduces the shared Mbed TLS heap optimisation for Arm
platforms. The objective is the Mbed TLS heap to be shared between BL1
and BL2 so as to not allocate the heap memory twice. To achieve that,
the patch introduces all the necessary helpers for implementing this
optimisation. It also applies it for FVP.
Change-Id: I6d85eaa1361517b7490956b2ac50f5fa0d0bb008
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
TF won't build since no memory region is specified
for when SEPARATE_CODE_AND_RODATA=0 it still relies on
the ARM_MAP_BL_RO_DATA region which is never defined for
this case. Create memory region combining code and RO data for
when the build flag SEPARATE_CODE_AND_RODATA=0 to fix this
Change-Id: I6c129eb0833497710cce55e76b8908ce03e0a638
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
The SGI platforms need to allocate memory for CPER buffers. These
platform buffers would be placed between the shared reserved memory
and the per cpu stack memory, thus the need to redefine stack base
pointer for these platforms. This patch allows each board in ARM
platform to define the PLAT_SP_IMAGE_STACK_BASE.
Change-Id: Ib5465448b860ab7ab0f645f7cb278a67acce7be9
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
Include arm_spm_def.h in the platform_def.h file. Without this
inclusion, we get build errors like
In file included from services/std_svc/spm/sp_setup.c:12:0:
services/std_svc/spm/sp_setup.c: In function 'spm_sp_setup':
services/std_svc/spm/sp_setup.c:61:57: error: 'PLAT_SPM_BUF_BASE'
undeclared (first use in this function)
write_ctx_reg(get_gpregs_ctx(ctx), CTX_GPREG_X0, PLAT_SPM_BUF_BASE);
Now that the platform_def.h includes arm_spm_def.h, remove inclusion
of platform_def.h in arm_spm_def.h to remove the circular dependency.
Change-Id: I5225c8ca33fd8d288849524395e436c3d56daf17
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
Change arm_setup_page_tables() to take a variable number of memory
regions. Remove coherent memory region from BL1, BL2 and BL2U as
their coherent memory region doesn't contain anything and
therefore has a size of 0. Add check to ensure this
doesn't change without us knowing.
Change-Id: I790054e3b20b056dda1043a4a67bd7ac2d6a3bc0
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
This also gets rid of MISRA violations for Rule 8.3 and 8.4.
Change-Id: I45bba011b16f90953dd4b260fcd58381f978eedc
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The ARM_INSTANTIATE_LOCK macro defines a lock meant to be further
manipulated using the arm_lock_init/get/release() macros. It has 2
variants, depending on the BL image it is compiled for. One version
defines the lock variable with internal linkage whereas the other one,
with external linkage.
Code that uses these macros is not compliant with MISRA rule 8.4 because
when using the external linkage version, there is no visible declaration
for the lock variable.
This patch defines the arm_lock variable with internal linkage in both
cases. This fits well the way these macros are used in the code today,
where the lock is not used outside of the translation unit it is
defined in.
Change-Id: I213a74a2a6088a4f1e9a61a319ca7579c2001320
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Clang linker doesn't support NEXT. As we are not using the MEMORY command
to define discontinuous memory for the output file in any of the linker
scripts, ALIGN and NEXT are equivalent.
Change-Id: I867ffb9c9a76d4e81c9ca7998280b2edf10efea0
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Currently TF-A doesn't initialise CNTFRQ register in CNTCTLBase
frame of the system timer. ARM ARM states that "The instance of
the register in the CNTCTLBase frame must be programmed with this
value as part of system initialization."
The psci_arch_setup() updates the CNTFRQ system register but
according to the ARM ARM, this instance of the register is
independent of the memory mapped instance. This is only an issue
for Normal world software which relies on the memory mapped
instance rather than the system register one.
This patch resolves the issue for ARM platforms.
The patch also solves a related issue on Juno, wherein
CNTBaseN.CNTFRQ can be written and does not reflect the value of
the register in CNTCTLBase frame. Hence this patch additionally
updates CNTFRQ register in the Non Secure frame of the CNTBaseN.
FixesARM-Software/tf-issues#593
Change-Id: I09cebb6633688b34d5b1bc349fbde4751025b350
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The old API is deprecated and will eventually be removed.
Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.
The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.
Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.
The size reserved for BL2 has been increased.
Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The translation tables allocated for the Secure Partition do not need
to be treated as a special case. They can be put amongst the other
tables mapping BL31's general purpose memory. They will be mapped with
the same attributes as them, which is fine.
The explicit alignment constraint in BL31's linker script to pad the
last page of memory allocated to the Secure Partition's translation
tables is useless too, as page tables are per se pages, thus their
end address is naturally aligned on a page-boundary.
In fact, this patch does not change the existing behaviour. Since
patch 22282bb68a ("SPM: Move all SP-related info to SP context
struct"), the secure_partition.c file has been renamed into sp_xlat.c
but the linker script has not been properly updated. As a result, the
SP translation tables are not specifically put at the start of the
xlat_table linker section, the __SP_IMAGE_XLAT_TABLES_START__/_END__
symbols have the same value, the size of the resulting mmap_region
covering these xlat tables is 0 and so it is ignored.
Change-Id: I4cf0a4cc090298811cca53fc9cee74df0f2b1512
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
For the BL2_AT_EL3 configuration, move BL2 higher up to make more
space for BL31. Adjust the BL31 limit to be up to BL2 base. This is
because BL2 is always resident for the BL2_AT_EL3 configuration and
thus we cannot overlay it with BL31.
Change-Id: I71e89863ed48f5159e8b619f49c7c73b253397aa
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
The patch changes the layout of BL images in memory to enable
more efficient use of available space. Previously BL31 was loaded
with the expectation that BL2 memory would be reclaimed by BL32
loaded in SRAM. But with increasing memory requirements in the
firmware, we can no longer fit BL32 in SRAM anymore which means the
BL2 memory is not reclaimed by any runtime image. Positioning BL2
below BL1-RW and above BL31 means that the BL31 NOBITS can be
overlaid on BL2 and BL1-RW.
This patch also propogates the same memory layout to BL32 for AArch32
mode. The reset addresses for the following configurations are also
changed :
* When RESET_TO_SP_MIN=1 for BL32 in AArch32 mode
* When BL2_AT_EL3=1 for BL2
The restriction on BL31 to be only in DRAM when SPM is enabled
is now removed with this change. The update to the firmware design
guide for the BL memory layout is done in the following patch.
Change-Id: Icca438e257abe3e4f5a8215f945b9c3f9fbf29c9
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
BL31 is running out of space, and the use-case of SPM doesn't require it
to be in SRAM. To prevent BL31 from running out of space in the future,
move BL31 to DRAM if SPM is enabled.
Secure Partition Manager design document updated to reflect the changes.
Increased the size of the stack of BL31 for builds with SPM.
The translation tables used by SPM in Arm platforms have been moved back
to the 'xlat_tables' region instead of 'arm_el3_tzc_dram'. Everything is
in DRAM now, so it doesn't make sense to treat them in a different way.
Change-Id: Ia6136c8e108b8da9edd90e9d72763dada5e5e5dc
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.
The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.
Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.
The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.
Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This reverts commit 2f18aa1fa3.
It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.
Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The bounds check in ARM_CASSERT_MMAP does not take into account the
array sentinel in plat_arm_mmap. This commit fixes this, and adds an
additional check to ensure the number of entries in the array is
within the bounds of PLAT_ARM_MMAP_ENTRIES.
Change-Id: Ie6df10c0aa0890d62826bc3224ad7b3e36fd53e2
Signed-off-by: Chris Kay <chris.kay@arm.com>
There are three calls to mmap_add_region() that always occur in
arm_setup_page_tables(), and two further calls based on whether coherent
memory is enabled, and whether SPM is enabled in BL31.
This commit adapts the ARM_BL_REGIONS definition to match the number of
calls made inside arm_setup_page_tables() so that the MAX_MMAP_REGIONS
is realigned with what is actually occurring.
Change-Id: I7adc05951abccf2cbd5c86280eb874911e6a1566
Signed-off-by: Chris Kay <chris.kay@arm.com>
The old API is deprecated and will eventually be removed.
Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.
The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.
Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.
The size of BL31 has been increased in builds with SPM.
Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
- Assign 0x10 for RAS exceptions on ARM platforms, and install
EHF priority descriptor.
- Call the common RAS initialisation from ARM BL31 setup.
- Add empty definitions for platform error records and RAS interrupts.
Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.
The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.
Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.
This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>
This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.
The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.
FixesARM-software/tf-issues#559
Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.3: All declarations of an object or function shall
use the same names and type qualifiers.
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I48201c9ef022f6bd42ea8644529afce70f9b3f22
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
MISRA C-2012 Rule 7.3 violation: lowercase l shall not be used as literal suffixes.
This patch resolves this for the ULL() macro by using ULL suffix instead
of the ull suffix.
Change-Id: Ia8183c399e74677e676956e8653e82375d0e0a01
Signed-off-by: David Cunado <david.cunado@arm.com>
The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :
1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.
2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.
3. The `libfdt` sources are now included when BL2 is built
4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.
5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.
6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.
Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.
Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.
Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.
The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:
--data cluster0.cpu0=bl2.bin@0x4001000
-C cluster0.cpu0.RVBAR=0x4001000
These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.
Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.
Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
A new platform define, `PLAT_SP_IMAGE_XLAT_SECTION_NAME`, has been
introduced to select the section where the translation tables used by
the S-EL1/S-EL0 are placed.
This define has been used to move the translation tables to DRAM secured
by TrustZone.
Most of the extra needed space in BL31 when SPM is enabled is due to the
large size of the translation tables. By moving them to this memory
region we can save 44 KiB.
A new argument has been added to REGISTER_XLAT_CONTEXT2() to specify the
region where the translation tables have to be placed by the linker.
Change-Id: Ia81709b4227cb8c92601f0caf258f624c0467719
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch fixes a couple of issues for AArch32 builds on ARM reference
platforms :
1. The arm_def.h previously defined the same BL32_BASE value for AArch64 and
AArch32 build. Since BL31 is not present in AArch32 mode, this meant that
the BL31 memory is empty when built for AArch32. Hence this patch allocates
BL32 to the memory region occupied by BL31 for AArch32 builds.
As a side-effect of this change, the ARM_TSP_RAM_LOCATION macro cannot
be used to control the load address of BL32 in AArch32 mode which was
never the intention of the macro anyway.
2. A static assert is added to sp_min linker script to check that the progbits
are within the bounds expected when overlaid with other images.
3. Fix specifying `SPD` when building Juno for AArch32 mode. Due to the quirks
involved when building Juno for AArch32 mode, the build option SPD needed to
specifed. This patch corrects this and also updates the documentation in the
user-guide.
4. Exclude BL31 from the build and FIP when building Juno for AArch32 mode. As
a result the previous assumption that BL31 must be always present is removed
and the certificates for BL31 is only generated if `NEED_BL31` is defined.
Change-Id: I1c39bbc0abd2be8fbe9f2dea2e9cb4e3e3e436a8
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
When defining different sections in linker scripts it is needed to align
them to multiples of the page size. In most linker scripts this is done
by aligning to the hardcoded value 4096 instead of PAGE_SIZE.
This may be confusing when taking a look at all the codebase, as 4096
is used in some parts that aren't meant to be a multiple of the page
size.
Change-Id: I36c6f461c7782437a58d13d37ec8b822a1663ec1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Factor out SPE operations in a separate file. Use the publish
subscribe framework to drain the SPE buffers before entering secure
world. Additionally, enable SPE before entering normal world.
A side effect of this change is that the profiling buffers are now
only drained when a transition from normal world to secure world
happens. Previously they were drained also on return from secure
world, which is unnecessary as SPE is not supported in S-EL1.
Change-Id: I17582c689b4b525770dbb6db098b3a0b5777b70a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Support SDEI on ARM platforms using frameworks implemented in earlier
patches by defining and exporting SDEI events: this patch defines the
standard event 0, and a handful of shared and private dynamic events.
Change-Id: I9d3d92a92cff646b8cc55eabda78e140deaa24e1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Define number of priority bits, and allocate priority levels for SDEI.
Change-Id: Ib6bb6c5c09397f7caef950c4caed5a737b3d4112
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The function arm_validate_ns_entrypoint() validates a given non-secure
physical address. This function however specifically returns PSCI error
codes.
Non-secure physical address validation is potentially useful across ARM
platforms, even for non-PSCI use cases. Therefore make this function
common by returning 0 for success or -1 otherwise.
Having made the function common, make arm_validate_psci_entrypoint() a
wrapper around arm_validate_ns_entrypoint() which only translates return
value into PSCI error codes. This wrapper is now used where
arm_validate_ns_entrypoint() was currently used for PSCI entry point
validation.
Change-Id: Ic781fc3105d6d199fd8f53f01aba5baea0ebc310
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This initial port of the Secure Partitions Manager to FVP supports BL31
in both SRAM and Trusted DRAM.
A document with instructions to build the SPM has been added.
Change-Id: I4ea83ff0a659be77f2cd72eaf2302cdf8ba98b32
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Achin Gupta <achin.gupta@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.
This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms. The
deprecated interrupt list definitions are however retained to support
legacy builds.
Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.
NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.
Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Provides GICv3 save/restore feature to arm_system_pwr_domain_resume and
arm_system_pwr_domain_save functions.
Introduce FVP PSCI power level 3 (System level) support. This is solely
done to provide example code on how to use the GICv3 save and restore
helpers.
Also make CSS GICv3 platforms power off the Redistributor on SYSTEM
SUSPEND as its state is saved and restored.
Change-Id: I0d852f3af8824edee1a17c085cf593ddd33a4e77
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Co-Authored-by: Douglas Raillard <douglas.raillard@arm.com>
Some recent enhancements to EL3 runtime firmware like support for
save and restoring GICv3 register context during system_suspend
necessitates additional data memory for the firmware. This patch
introduces support for creating a TZC secured DDR carveout for use
by ARM reference platforms. A new linker section `el3_tzc_dram` is
created using platform supplied linker script and data marked with
the attribute `arm_el3_tzc_dram` will be placed in this section.
The FVP makefile now defines the `PLAT_EXTRA_LD_SCRIPT` variable to
allow inclusion of the platform linker script by the top level BL31
linker script.
Change-Id: I0e7f4a75a6ac51419c667875ff2677043df1585d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
On ARM platforms, the maximum size of the address space is limited
to 32-bits as defined in arm_def.h. In order to access DRAM2, which
is defined beyond the 32-bit address space, the maximum address space
is increased to 36-bits in AArch64. It is possible to increase the
virtual space for AArch32, but it is more difficult and not supported
for now.
NOTE - the actual maximum memory address space is platform dependent
and is checked at run-time by querying the PARange field in the
ID_AA64MMFR0_EL1 register.
Change-Id: I6cb05c78a63b1fed96db9a9773faca04a5b93d67
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
mem_protect needs some kind of non-volatile memory because it has
to remember its state across reset and power down events.
The most suitable electronic part for this feature is a NVRAM
which should be only accesible from the secure world. Juno and
FVP lack such hardware and for this reason the MEM_PROTECT
functionality is implemented with Flash EEPROM memory on both
boards, even though this memory is accesible from the non-secure
world. This is done only to show a full implementation of
these PSCI features, but an actual system shouldn't use a
non-secure NVRAM to implement it.
The EL3 runtime software will write the mem_protect flag and BL2
will read and clear the memory ranges if enabled. It is done in
BL2 because it reduces the time that TF needs access to the full
non-secure memory.
The memory layout of both boards is defined using macros which
take different values in Juno and FVP platforms. Generic platform
helpers are added that use the platform specific macros to generate
a mem_region_t that is valid for the platform.
Change-Id: I2c6818ac091a2966fa07a52c5ddf8f6fde4941e9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>