Currently the SP package loading mechanism is only enabled when S-EL2
SPMC is selected. Remove this limitation.
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Change-Id: I5bf5a32248e85a26d0345cacff7d539eed824cfc
Update UUID to little endian:
The SPMC expects a little endian representation of the UUID as an array
of four integers in the SP manifest.
Add managed exit field and cosmetic comments updates.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Icad93ca70bc27bc9d83b8cf888fe5f8839cb1288
* changes:
feat(docs/nxp/layerscape): add ls1028a soc and board support
feat(plat/nxp/ls1028ardb): add ls1028ardb board support
feat(plat/nxp/ls1028a): add ls1028a soc support
feat(plat/nxp/common): define default SD buffer
feat(driver/nxp/xspi): add MT35XU02G flash info
feat(plat/nxp/common): add SecMon register definition for ch_3_2
feat(driver/nxp/dcfg): define RSTCR_RESET_REQ
feat(plat/nxp/common/psci): define CPUECTLR_TIMER_2TICKS
feat(plat/nxp/common): define default PSCI features if not defined
feat(plat/nxp/common): define common macro for ARM registers
feat(plat/nxp/common): add CCI and EPU address definition
The LS1028A reference design board (RDB) is a computing,
evaluation, and development platform that supports industrial
IoT applications, human machine interface solutions, and
industrial networking.
It supports the following features:
1. Layerscape LS1028A dual-core processor based on Cortex-A72
at 1.3 GHz.
2. 4 GB DDR4 SDRAM w/ECC
3. Support Ethernet:
1) x1 RJ45 connector for 1Gbps Ethernet support w/TSN, 1588
2) x4 RJ45 connector for 1Gbps Ethernet switch support w/TSN,
1588 (QSGMII)
3. With Basic Peripherals and Interconnect
2x M.2 Type E slots with PCIe Gen 3.0 x1
1x M.2 Type B slot with SATA 3.0 (resistor mux with 1 Type E slot)
1x Type A USB 3.0 super-speed port
1x Type C USB 3.0 super-speed port
1x DisplayPort interface
2x DB9 RS232 serial ports
2x DB9 CAN interfaces
1x 3.5 mm audio out
2x MikroBUS™ sockets
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Change-Id: I48ee254a488ae4af227641da3875a1e9a63a720c
The QorIQ LS1028A processor integrates two 64-bit ARM Cortex-A72
cores with a GPU and LCD controller, as well as a TSNenabled
Ethernet port and a TSN-enabled switch with four external ports.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Change-Id: I9f65c6af5db7e20702828cd208290c1b43a54941
* changes:
feat(plat/fvp): enable trace extension features by default
feat(trf): enable trace filter control register access from lower NS EL
feat(trf): initialize trap settings of trace filter control registers access
feat(sys_reg_trace): enable trace system registers access from lower NS ELs
feat(sys_reg_trace): initialize trap settings of trace system registers access
feat(trbe): enable access to trace buffer control registers from lower NS EL
feat(trbe): initialize trap settings of trace buffer control registers access
Trusted Services had removed secure storage and added two new
trusted services - Protected Storage and Internal Trusted Storage.
Hence we are removing secure storage and adding support for the
internal trusted storage.
And enable external SP images in BL2 config for TC, so that
we do not have to modify this file whenever the list of SPs
changes. It is already implemented for fvp in the below commit.
commit 33993a3737
Author: Balint Dobszay <balint.dobszay@arm.com>
Date: Fri Mar 26 15:19:11 2021 +0100
feat(fvp): enable external SP images in BL2 config
Change-Id: I3e0a0973df3644413ca5c3a32f36d44c8efd49c7
Signed-off-by: Davidson K <davidson.kumaresan@arm.com>
Define default SD buffer address and size in DRAM.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I5872d95b0c1114e05f0e145756e9a6ef39b2fd9a
SoC code can define supported features, otherwise use default setting.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I0f11498c1f7558ff0ec2d9b344f3f7a4f5489ced
Define common register macro both for Cortex-A53 and Cortex-A72
because the code will be used by both Cortex platform.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I485661bfe3ed4f214c403ff6af53dc6af1ddf089
Add CCI and EPU base address definiton for Chassis v3.2.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I13250555b6646c1e7ba2e9d7c9efca8501f17b3a
EMI MPU stands for external memory interface memory protect unit.
MT8195 supports 32 regions and 16 domains.
We add basic drivers currently, and will add more setting for
EMI MPU in next patch.
Change-Id: Iedc19d8f6fcf1ceb2d8241319b8dc17c885642dd
Signed-off-by: Penny Jan <penny.jan@mediatek.com>
In the SCMI power domain off handling, configure GIC
to prevent interrupt toward to the core to be turned off,
and configure CCN to disable coherency when the cluster is turned off.
The same operation is done in SCPI power domain off processing.
This commit adds the missing operation in SCMI power domain
off handling.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Change-Id: Ib3523de488500c2e8bdc74e4cb8772a1442d9781
Erratum 1530924 affects Armada 37xx CPU, since it affects all Cortex-A53
revisions from r0p0 to r0p4.
Enable the workaround for this erratum.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I753225040e49e956788d5617cd7ce76d5e6ea8e8
BL2 passes FW_CONFIG to BL31 which contains information
about different DTBs present. BL31 then uses FW_CONFIG
to get the base address of HW_CONFIG and populate fconf.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Change-Id: I0b4fc83e6e0a0b9401f692516654eb9a3b037616
This avoids duplicate define of TZC_REGION_NSEC_ALL_ACCESS_RDWR.
And remove the previous TZC400 definitions from stm32mp1_def.h.
Change-Id: I6c72c2a18731f69d855fbce8ce822a21da9364fa
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Add required code to support FCONF on STM32MP1 platform.
The new FW_CONFIG DT file will be inside the FIP, and loaded by BL2.
It will be used to configure the addresses where to load other binaries.
BL2 should be agnostic of which BL32 is in the FIP (OP-TEE or SP_min),
so optee_utils.c is always compiled, and some OP-TEE flags are removed.
Change-Id: Id957b49b0117864136250bfc416664f815043ada
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Instead of using a scratch buffer of 512 bytes, we can directly use the
image address and max size. The mmc_block_dev_spec struct info is then
overwritten for each image with this info, except FW_CONFIG and GPT
table which will still use the scratch buffer.
This allows using multiple blocks read on MMC, and so improves the boot
time.
A cache invalidate is required for the remaining data not used from the
first and last blocks read. It is not required for FW_CONFIG_ID,
as it is in scratch buffer in SYSRAM, and also because bl_mem_params
struct is overwritten in this case. This should also not be done if
the image is not found (OP-TEE extra binaries when using SP_min).
Change-Id: If3ecfdfe35bb9db66284036ca49c4bd1be4fd121
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
BL2 still uses the STM32 header binary format to be loaded from ROM code.
BL32 and BL33 and their respective device tree files are now put together
in a FIP file.
One DTB is created for each BL. To reduce their sizes, 2 new dtsi file are
in charge of removing useless nodes for a given BL. This is done because
BL2 and BL32 share the same device tree files base.
The previous way of booting is still available, the compilation flag
STM32MP_USE_STM32IMAGE has to be set to 1 in the make command. Some files
are duplicated and their names modified with _stm32_ to avoid too much
switches in the code.
Change-Id: I1ffada0af58486d4cf6044511b51e56b52269817
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Protect BL32 (SP_min) with MMU if OP-TEE is not used.
Validate OP-TEE header with optee_header_is_valid().
Use default values in bl2_mem_params_descs[]. They will be overwritten
in bl2_plat_handle_post_image_load() if OP-TEE is used.
Change-Id: I8614f3a17caa827561614d0f25f30ee90c4ec3fe
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
* changes:
refactor(plat/nxp): refine api to read SVR register
refactor(plat/nxp): each errata use a seperate source file
refactor(plat/nxp): use a unified errata api
refactor(plat/soc-lx2160): move errata to common directory
Currently the list of SP UUIDs loaded by BL2 is hardcoded in the DT.
This is a problem when building a system with other SPs (e.g. from
Trusted Services). This commit implements a workaround to enable adding
SP UUIDs to the list at build time.
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Change-Id: Iff85d3778596d23d777dec458f131bd7a8647031
Up until now we relied on the GICs used in our FPGA images to be GICv3
compliant, without the "direct virtual injection" feature (aka GICv4)
enabled.
To support newer images which have GICv4 compliant GICs, enable the
newly introduced GICv4 detection code, and use that also when we adjust
the redistributor region size in the devicetree.
This allows the same BL31 image to be used with GICv3 or GICv4 FPGA
images.
Change-Id: I9f6435a6d5150983625efe3650a8b7d1ef11b1d1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment we have a GIC_ENABLE_V4_EXTN build time variable to
determine whether the GIC interrupt controller is compliant to version
4.0 of the spec or not. This just changes the number of 64K MMIO pages
we expect per redistributor.
To support firmware builds which run on variable systems (emulators,
fast model or FPGAs), let's make this decision at runtime.
The GIC specification provides several architected flags to learn the
size of the MMIO frame per redistributor, we use GICR_TYPER[VLPI] here.
Provide a (static inline) function to return the size of each
redistributor.
We keep the GIC_ENABLE_V4_EXTN build time variable around, but change
its meaning to enable this autodetection code. Systems not defining this
rely on a "pure" GICv3 (as before), but platforms setting it to "1" can
now deal with both configurations.
Change-Id: I9ede4acf058846157a0a9e2ef6103bf07c7655d9
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Balint Dobszay
Olivier Deprez
Joanna Farley
Madhukar Pappireddy
Jiafei Pan
Saurabh Gorecha
Manish Pandey
Rex-BC Chen
Davidson K
Penny Jan
Masahisa Kojima
Dawei Chien
Julius Werner
André Przywara
Mark Dykes
Marek Behún
Lionel Debieve
Usama Arif
Yann Gautier