Ensure 'PLAT_SEC_ENTRY' is cleared during early platform
setup. This is to prevent the slave CPU cores jump to the stale
entry point after warm reset when using U-Boot SPL as first
stage boot loader.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Change-Id: I3294ce2f74aa691d0cf311fa30f27f9d4fb8800a
* changes:
plat: marvell: armada: Building ${DOIMAGETOOL} is only for a8k
plat: marvell: armada: Fix including plat/marvell/marvell.mk file
plat: marvell: armada: a3k: When WTP is empty do not define variables and targets which depends on it
The qemu_sbsa platform uses 42bit address size but
the cortex-a53 only supports 40bit addressing, the
cpu is incompatible with the platform.
The aem_generic is also not used with qemu_sbsa, in
fact, the platform currently only properly supports
the cortex-a57 cpu.
Change-Id: I91c92533116f1c3451d01ca99824e91d3d58df14
Signed-off-by: Tomas Pilar <tomas@nuviateam.com>
Currently a3k target is misusing ${DOIMAGETOOL} target for building flash
and UART images. It is not used for building image tool.
So move ${DOIMAGETOOL} target from common marvell include file into a8k
include file and add correct invocation of ${MAKE} into a3k for building
flash and UART images.
Part of this change is also checks that MV_DDR_PATH for a3k was specified
by user as this option is required for building a3k flash and UART images.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I5ae9d08b8505460933f17836c9b6435fd6e51bb6
This includes configuration for SPMC and trusted OS.
Change-Id: Ie24df200f446b3f5b23f5f764b115c7191e6ada3
Signed-off-by: Usama Arif <usama.arif@arm.com>
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
This patch enables SPMC execution at S-EL2 by adding below changes
- Map TC0_MAP_TZC_DRAM1 for loading SPMC
- Add details of cactus test secure partitions
- Adds tc0 spmc manifest file with details on secure partitions
- Inlcude TOS_FW_CONFIG when SPM is spmd
- Increases bl2 image size
SPMC at S-EL2 is only enabled when build with SPD=spmd.
Change-Id: I4c5f70911903c232ee8ecca57f1e288d6b1cd647
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
- Reserve 32MB below ARM_AP_TZC_DRAM1_BASE for TC0_TZC_DRAM1
- Add TC0_NS_DRAM1 base and mapping
- Reserve memory region in tc0.dts
Change-Id: If2431f7f68e4255e28c86a0e89637dab7c424a13
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
To support platforms without Trusted DRAM this patch defines
PLAT_ARM_SPMC_BASE and enables platform to use either Trusted DRAM or
DRAM region behind TZC.
Change-Id: Icaa5c7d33334258ff27e8e0bfd0812c304e68ae4
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Statistical Profiling Extension is not supported by Matterhorn core
Change-Id: Iec652f1c6d6b6a9bf118ba682276a7c70a6abc0d
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Include file plat/marvell/marvell.mk for platform A3700 was included two
times. Once from file plat/marvell/armada/a3k/common/a3700_common.mk and
second time from common file plat/marvell/armada/common/marvell_common.mk.
It caused following warning every time was make called:
plat/marvell/marvell.mk:51: warning: overriding recipe for target 'mrvl_clean'
plat/marvell/marvell.mk:51: warning: ignoring old recipe for target 'mrvl_clean'
Change in this commit removes inclusion of plat/marvell/marvell.mk file in
common file plat/marvell/armada/common/marvell_common.mk. As a80x0 platform
needs this include file, add it also into a80x0 platform specific include
file lat/marvell/armada/a8k/common/a8k_common.mk.
Also moves inclusion of plat/marvell/marvell.mk file in a3700 platform file
plat/marvell/armada/a3k/common/a3700_common.mk at correct place. Global
plat/marvell/marvell.mk expects that variables DOIMAGEPATH and DOIMAGETOOL
are already defined, but it defines MARVELL_SECURE_BOOT variable which is
needed by plat/marvell/armada/a3k/common/a3700_common.mk.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I5cbbd7eb8a3376924419f9850516b2a4924be5aa
implementation of SMC call SMCCC_ARCH_SOC_ID
adding debugging logs in mem assign call.
Checking range of param in mem_assign call is from CB_MEM_RAM
or CB_MEM_RESERVED.
Change-Id: Iba51bff154df01e02dcb7715582ffaff7beba26e
Signed-off-by: Saurabh Gorecha <sgorecha@codeaurora.org>
Some of targets (e.g. mrvl_flash) depends on WTP build option. Other
targets (e.g. fip) can be build also without WTP build option as they do
not depend on it.
This change put all A3720 variables and targets which depends on WTP into
conditional if-endif section, so they are not defined when user has not
supplied WTP build option.
Target mrvl_flash is defined also when WTP was not specified and in this
case it just print error message to help user.
Variables which do not depend on WTP are moved to the top of
a3700_common.mk file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Idb3892233586a0afca3e0e6564279641d2e4b960
The board information values, read in an OTP are never negative,
%u is then used instead of %d.
Change-Id: I3bc22401fb4d54666ddf56411f75b79aca738492
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Retrieve peripheral base address from a define instead of
parsing the device tree. The goal is to improve execution time.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I2588c53ad3d4abcc3d7fe156458434a7940dd72b
Update the board info with the new coding including the finished good
variant:
Board: MBxxxx Var<CPN>.<FG> Rev.<Rev>-<BOM>
The OTP 59 coding is:
bit [31:16] (hex) => MBxxxx
bit [15:12] (dec) => Variant CPN (1....15)
bit [11:8] (dec) => Revision board (index with A = 1, Z = 26)
bit [7:4] (dec) => Variant FG : finished good (NEW)
bit [3:0] (dec) => BOM (01, .... 255)
Change-Id: I4fbc0c84596419d1bc30d166311444ece1d9123f
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I2b702698d6be93da5ac86da1cbc98b3838315a5a
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Update to support new part numbers.
Add new STM32 MPUs Part = STM32MP151F, STM32MP153F, STM32MP157F,
STM32MP151D, STM32MP153D, STM32MP157D
The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz
Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :
- A Basic + Cortex-A7 @ 650 MHz
- C Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D Basic + Cortex-A7 @ 800 MHz
- F Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz
Remove useless variable in stm32mp_is_single_core().
Change-Id: Id30c836af986c6340c91efa8a7ae9480a2827089
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Add a new revision of STM32MP15x CPU (Rev.Z).
Change-Id: I227dd6d9b3fcc43270015cfb21f60aeb0a8ab658
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Usually, C has no problem up-converting types to larger bit sizes. MISRA
rule 10.7 requires that you not do this, or be very explicit about this.
This resolves the following required rule:
bl1/aarch64/bl1_context_mgmt.c:81:[MISRA C-2012 Rule 10.7 (required)]<None>
The width of the composite expression "0U | ((mode & 3U) << 2U) | 1U |
0x3c0U" (32 bits) is less that the right hand operand
"18446744073709547519ULL" (64 bits).
This also resolves MISRA defects such as:
bl2/aarch64/bl2arch_setup.c:18:[MISRA C-2012 Rule 12.2 (required)]
In the expression "3U << 20", shifting more than 7 bits, the number
of bits in the essential type of the left expression, "3U", is
not allowed.
Further, MISRA requires that all shifts don't overflow. The definition of
PAGE_SIZE was (1U << 12), and 1U is 8 bits. This caused about 50 issues.
This fixes the violation by changing the definition to 1UL << 12. Since
this uses 32bits, it should not create any issues for aarch32.
This patch also contains a fix for a build failure in the sun50i_a64
platform. Specifically, these misra fixes removed a single and
instruction,
92407e73 and x19, x19, #0xffffffff
from the cm_setup_context function caused a relocation in
psci_cpus_on_start to require a linker-generated stub. This increased the
size of the .text section and caused an alignment later on to go over a
page boundary and round up to the end of RAM before placing the .data
section. This sectionn is of non-zero size and therefore causes a link
error.
The fix included in this reorders the functions during link time
without changing their ording with respect to alignment.
Change-Id: I76b4b662c3d262296728a8b9aab7a33b02087f16
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
And from crash_console_flush.
We ignore the error information return by console_flush in _every_
place where we call it, and casting the return type to void does not
work around the MISRA violation that this causes. Instead, we collect
the error information from the driver (to avoid changing that API), and
don't return it to the caller.
Change-Id: I1e35afe01764d5c8f0efd04f8949d333ffb688c1
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Remove some useless extra tabs or spaces.
Replace some spaces with tabs.
Change-Id: I0e8e2a1a1be7a1109ba7f3e3ae35e3fe1b5b4552
Signed-off-by: Yann Gautier <yann.gautier@st.com>
In heavy parallel builds, it has sometimes been seen issues with the
tool not generated before it was needed. Change some rules order and
dependency to solve that.
Change-Id: I8f4b4f46a2ea0fe496bc66bca47c66d1c81d3c99
Signed-off-by: Yann Gautier <yann.gautier@st.com>
There were fixed values when computing PLAT_PARTITION_MAX_ENTRIES.
Use STM32_BL33_PARTS_NUM and STM32_RUNTIME_PARTS_NUM. The first one is
for the number of copies of BL33. The second one depends on the use case
SP_min or OP-TEE. For OP-TEE, there are 3 partitions. For SP_min, as it
is in the same binary as BL2, it is set to 0. It will be set to 1 if
BL32 is in a separate binary.
Change-Id: Iba4d8ec5fbc713bebfbdcd9f9426c3fded20d3ad
Signed-off-by: Yann Gautier <yann.gautier@st.com>
First put Makefile variables definition, then definitions for each feature,
then C flags, then source files, then compilation rules.
Change-Id: I238115ea2fe4ebafccd2135979814c27932c34e2
Signed-off-by: Yann Gautier <yann.gautier@st.com>
To simplify the rule that creates the concatenated binary, use ASFLAGS
instead of adding all paths in the AS command line. This allows a better
management if a binary is not present.
Change-Id: Ic8b4566e7dedc6f55be355a92e3b214cef138d9b
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The previous proprietary version was not correctly handling dependencies.
Using MAKE_LD from make_helpers files now correctly handles that.
The generated linker script is the same as before.
Change-Id: Iccfd8dc3fffa7a33e73b184b72e0dfd5d26bc9c9
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Only define arm_get_rotpk_info_regs if ROTPK is in registers,
i.e. (ARM_ROTPK_LOCATION_ID == ARM_ROTPK_REGS_ID). This will
allow platform build without definition of TZ_PUB_KEY_HASH_BASE
if dedicated registers for ROTPK are not available on the platform.
Change-Id: I74ee2d5007f5d876a031a1efca20ebee2dede0c7
Signed-off-by: Usama Arif <usama.arif@arm.com>
Add *.bin extension to UART recovery images archive name.
Such naming will cause the UART recovery images to be copied to the
Buildroot output folder upon flash image build.
Change-Id: I6992df1ab2ded725bed58e5baf245ae92c4cb289
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Marvell uses RAM address 0x0 for loading BL33 stage images.
When ATF is built with DEBUG=1, its IO subsystem fails on
assert checking the destination RAM address != 0.
This patch adds PLAT_ALLOW_ZERO_ADDR_COPY to A3K platform
allowing to bypass the above check in debug mode.
Change-Id: I687e35cb2e9dc3166bdaa81b3904c20b784c5c6a
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
The polarity inversion for USB was not tested due to lack of hw design
which requires it. Currently all supported boards doesn't require USB
phy polarity inversion, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards. Enable the option for the ones that need it.
Change-Id: Ia5f2ee313a93962e94963e2dd8a759ef6d9da369
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The cp110 comphy has ability to invert RX and/or TX polarity. Polarity
depends on board design. Currently all supported boards doesn't require
SATA phy polarity invert, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards.
Change-Id: Ifd0bc6aaf8a76a0928132b197422f3193cf020d5
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
ERRATA ID: FE-4265711 - Incorrect CNTVAL reading
CNTVAL reflects the global system counter value in binary format.
Due to this erratum, the CNTVAL value presented to the processor
may be incorrect for several clock cycles.
Workaround: Override the default value of AP Register Device General
control 20 [19:16] and AP Register Device General Control 21 [11:8]
to the value of 0x3.
Change-Id: I1705608d08acd9631ab98d6f7ceada34d6b8336f
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
This patch makes changes required to get the morello
platform working with the tip of TF-A.
Change-Id: I095006615c9959bba49fcc75b52e1de7d7486309
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
* changes:
arm_fpga: Add platform documentation
arm_fpga: Add post-build linker script
arm_fpga: Add ROM trampoline
arm_fpga: Add devicetree file
arm_fpga: Remove SPE PMU DT node if SPE is not available
arm_fpga: Adjust GICR size in DT to match number of cores
fdt: Add function to adjust GICv3 redistributor size
drivers: arm: gicv3: Allow detecting number of cores
For the Arm Ltd. FPGAs to run, we need to load several payloads into the
FPGA's memory:
- Some trampoline code at address 0x0, to jump to BL31's entry point.
- The actual BL31 binary at the beginning of DRAM.
- The (generic) DTB image to describe the hardware.
- The actual non-secure payloads (kernel, ramdisks, ...)
The latter is application specific, but the first three blobs are rather
generic.
Since the uploader tool supports ELF binaries, it seems helpful to
combine these three images into one .axf file, as this also simplifies
the command line.
Add a post-build linker script, that combines those three bits into one
ELF file, together with their specific load addresses.
Include a call to "ld" with this linker script in the platform Makefile,
so it will be build automatically. The result will be called "bl31.axf".
Change-Id: I4a90da16fa1e0e83b51d19e5b1daf61f5a0bbfca
Signed-off-by: Andre Przywara <andre.przywara@arm.com>