The board features the Hi3798C V200 with an integrated quad-core
64-bit ARM Cortex A53 processor and high performance Mali T720 GPU,
making it capable of running any commercial set-top solution based on
Linux or Android. Its high performance specification also supports a
premium user experience with up to H.265 HEVC decoding of 4K video at
60 frames per second.
SOC Hisilicon Hi3798CV200
CPU Quad-core ARM Cortex-A53 64 bit
DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB
USB Two USB 2.0 ports One USB 3.0 ports
CONSOLE USB-micro port for console support
ETHERNET 1 GBe Ethernet
PCIE One PCIe 2.0 interfaces
JTAG 8-Pin JTAG
EXPANSION INTERFACE Linaro 96Boards Low Speed Expansion slot
DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor
WIFI 802.11AC 2*2 with Bluetooth
CONNECTORS One connector for Smart Card One connector for TSI
The platform boot sequence is as follows:
l-loader --> arm_trusted_firmware --> u-boot
Repositories:
- https://github.com/Linaro/poplar-l-loader.git
- https://github.com/Linaro/poplar-u-boot.git
U-Boot is also upstream in the project's master branch.
Make sure you are using the correct branch on each one of these
repositories. The definition of "correct" might change over time (at
this moment in time this would be the "latest" branch).
Build Line:
make CROSS_COMPILE=aarch64-linux-gnu- all fip SPD=none DEBUG=1
PLAT=poplar BL33=/path/to/u-boot.bin
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>
This fix modifies the order of system includes to meet the ARM TF coding
standard. There are some exceptions to this change in order to retain
header groupings and where there are headers within #if statements.
Change-Id: Ib5b668c992d817cc860e97b29e16ef106d17e404
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>
This fix modifies the order of #includes in ARM standard platforms
to meet the ARM TF coding standard.
Change-Id: Ide19aad6233babda4eea2d17d49e523645fed1b2
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>
PLATFORM_LINKER_FORMAT
and
PLATFORM_LINKER_ARCH
defines are removed from
plat/hisilicon/hikey/include/platform_def.h
since there are already defined in
include/plat/common/common_def.h
which is included by
plat/hisilicon/hikey/hikey_def.h
which is included by
plat/hisilicon/hikey/include/platform_def.h
The line
$(eval $(call FIP_ADD_IMG,SCP_BL2,--scp-fw))
is removed from
plat/hisilicon/hikey/platform.mk
to clear the warning below:
Makefile:544: warning: overriding commands for target `check_SCP_BL2'
plat/hisilicon/hikey/platform.mk:19: warning: ignoring old commands for target `check_SCP_BL2'
$(eval $(call FIP_ADD_IMG,SCP_BL2,--scp-fw))
already exists in
Makefile
and applies to plat hikey so is redundant in
plat/hisilicon/hikey/platform.mk
Signed-off-by: Victor Chong <victor.chong@linaro.org>
The line
$(eval $(call FIP_ADD_IMG,SCP_BL2,--scp-fw))
is removed from
plat/hisilicon/hikey960/platform.mk
to clear the warning below:
Makefile:544: warning: overriding commands for target `check_SCP_BL2'
plat/hisilicon/hikey960/platform.mk:13: warning: ignoring old commands for
target `check_SCP_BL2'
$(eval $(call FIP_ADD_IMG,SCP_BL2,--scp-fw))
already exists in
Makefile
and applies to plat hikey960 so is redundant in
plat/hisilicon/hikey960/platform.mk
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Decrypt device private keys which transfer from kernel, then stuff it to
DP controller. So that DP driver could start HDCP authentication in
kernel.
Change-Id: If3c2cd99bca811fe5fc30acc88bf5dc1afd7416d
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
This patch fixes the two things as follows:
1) rk3399_flash_l2_b" seems to be a typo. That's "flush", not "flash".
2) fixes the warnings log.
We always hit the warnings thing during the suspend, as below log:
..
[ 51.022334] CPU5: shutdown
[ 51.025069] psci: CPU5 killed.
INFO: sdram_params->ddr_freq = 928000000
WARNING: rk3399_flash_l2_b:reg 28830380,wait
When the L2 completes the clean and invalidate sequence, it asserts the
L2FLUSHDONE signal. The SoC can now deassert L2FLUSHREQ signal and then
the L2 deasserts L2FLUSHDONE.
Then, a loop without a delay isn't really great to measure time. We should
probably add a udelay(10) or so in there and then maybe replace the WARN()
after the loop. In the actual tests, the L2 cache will take ~4ms by
default for big cluster.
In the real world that give 10ms for the enough margin, like the
ddr/cpu/cci frequency and other factors that will affect it.
Change-Id: I55788c897be232bf72e8c7b0e10cf9b06f7aa50d
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
This patch implements the platform APIs plat_get_rotpk_info,
plat_get_nv_ctr, plat_set_nv_ctr to invoke CryptoCell SBROM
APIs when ARM_CRYPTOCELL_INT is set.
Change-Id: I693556b3c7f42eceddd527abbe6111e499f55c45
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch makes the necessary changes to enable ARM platform to
successfully integrate CryptoCell during Trusted Board Boot. The
changes are as follows:
* A new build option `ARM_CRYPTOCELL_INTEG` is introduced to select
the CryptoCell crypto driver for Trusted Board boot.
* The TrustZone filter settings for Non Secure DRAM is modified
to allow CryptoCell to read this memory. This is required to
authenticate BL33 which is loaded into the Non Secure DDR.
* The CSS platforms are modified to use coherent stacks in BL1 and BL2
when CryptoCell crypto is selected. This is because CryptoCell makes
use of DMA to transfer data and the CryptoCell SBROM library allocates
buffers on the stack during signature/hash verification.
Change-Id: I1e6f6dcd1899784f1edeabfa2a9f279bbfb90e31
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
For rk3399, the L2ACTLR[14] is 0 by default, as ACE CCI-500 doesn't
support WriteEvict. and you will hit the condition L2ACTLR[3] with 0,
as the Evict transactions should propagate to CCI-500 since it has
snoop filters.
Maybe this erratum applies to all Cortex-A53 cores so far, especially
if RK3399's A53 is a r0p4. we should enable it to avoid data corruption,
Change-Id: Ib86933f1fc84f8919c8e43dac41af60fd0c3ce2f
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
A recent commit 030567e6f5 added U()/ULL()
macro to TF constants. This has caused some signed-unsigned comparison
warnings / errors in the TF static analysis.
This patch addresses these issues by migrating impacted variables from
signed ints to unsigned ints and vice verse where applicable.
Change-Id: I4b4c739a3fa64aaf13b69ad1702c66ec79247e53
Signed-off-by: David Cunado <david.cunado@arm.com>
On Juno AArch32, the L2 cache may contain garbage after the warm reset
from AArch64 to AArch32. This is all fine until the MMU is configured
and the data caches enabled. To avoid fetching stale data from the L2
unified cache, invalidate it before the warm reset to AArch32 state.
Change-Id: I7d27e810692c02c3e83c9f31de67f6bae59a960a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Before BL2 loads the SCP ram firmware, `SCP_BOOT_CFG_ADDR` specifies
the primary core. After the SCP ram firmware has started executing,
`SCP_BOOT_CFG_ADDR` is modified. This is not normally an issue but
the Juno AArch32 boot flow is a special case. BL1 does a warm reset
into AArch32 and the core jumps to the `sp_min` entrypoint. This is
effectively a `RESET_TO_SP_MIN` configuration. `sp_min` has to be
able to determine the primary core and hence we need to restore
`SCP_BOOT_CFG_ADDR` to the cold boot value before `sp_min` runs.
This magically worked when booting on A53 because the core index was
zero and it just so happened to match with the new value in
`SCP_BOOT_CFG_ADDR`.
Change-Id: I105425c680cf6238948625c1d1017b01d3517c01
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
For some reason, HDCP key decrytion can't open source in ATF, so we
build it as hdcp.bin. Besides declare the handler for decrypting.
Change-Id: Ia67ff2442ab43cb3ee4875b3d59cc1608e854b4b
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Use TF_CFLAGS instead of CFLAGS, to allow CFLAGS to be overriden from
the make command line.
Change-Id: I3e5726c04bcd0176f232581b8be2c94413374ac7
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
These errata are only applicable to AArch64 state. See the errata notice
for more details:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.epm048406/index.html
Introduce the build options ERRATA_A53_835769 and ERRATA_A53_843419.
Enable both of them for Juno.
Apply the 835769 workaround as following:
* Compile with -mfix-cortex-a53-835769
* Link with --fix-cortex-a53-835769
Apply the 843419 workaround as following:
* Link with --fix-cortex-a53-843419
The erratum 843419 workaround can lead the linker to create new sections
suffixed with "*.stub*" and 4KB aligned. The erratum 835769 can lead the
linker to create new "*.stub" sections with no particular alignment.
Also add support for LDFLAGS_aarch32 and LDFLAGS_aarch64 in Makefile for
architecture-specific linker options.
Change-Id: Iab3337e338b7a0a16b0d102404d9db98c154f8f8
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
SPE is only supported in non-secure state. Accesses to SPE specific
registers from SEL1 will trap to EL3. During a world switch, before
`TTBR` is modified the SPE profiling buffers are drained. This is to
avoid a potential invalid memory access in SEL1.
SPE is architecturally specified only for AArch64.
Change-Id: I04a96427d9f9d586c331913d815fdc726855f6b0
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Currently, ROTPK_NOT_DEPLOYED flag is set in plat_get_rotpk_info().
It is up to users how to retrieve ROTPK if the ROT verification is
desired. This is not nice.
This commit improves plat_get_rotpk_info() implementation and automates
the ROTPK deployment. UniPhier platform has no ROTPK storage, so it
should be embedded in BL1/BL2, like ARM_ROTPK_LOCATION=devel_rsa case.
This makes sense because UniPhier platform implements its internal ROM
i.e. BL1 is used as updatable pseudo ROM.
Things work like this:
- ROT_KEY (default: $(BUILD_PLAT)/rot_key.pem) is created if missing.
Users can override ROT_KEY from the command line if they want to
use a specific ROT key.
- ROTPK_HASH is generated based on ROT_KEY.
- ROTPK_HASH is included by uniphier_rotpk.S and compiled into BL1/BL2.
- ROT_KEY is input to cert_create tool.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On ARM platforms before exiting from SP_MIN ensure that
the default console is switched to the runtime serial port.
Change-Id: I0ca0d42cc47e345d56179eac16aa3d6712767c9b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
With GCC 6.2 compiler, more C undefined behaviour is being flagged as
warnings, which result in build errors in ARM TF build.
This patch addresses issue caused by enums with values that exceed
maximum value for an int. For these cases the enum is converted to
a set of defines.
Change-Id: I5114164be10d86d5beef3ea1ed9be5863855144d
Signed-off-by: David Cunado <david.cunado@arm.com>
The patch fb7d32e588 migrated the CPU
libraries to have unique defines, prefixing them with the CPU name.
This patch migrates the hikey960 platform port to use the A53 specific
defines.
Change-Id: Id76f544b0b236bbd4974ab5ffa1203f073c20021
Signed-off-by: David Cunado <david.cunado@arm.com>
In CPU off callback function, the old code uses the function
hisi_test_pwrdn_allcores() to check if all CPUs in cluster have been
powered off and if it's valid then power off the whole cluster. But the
function hisi_test_pwrdn_allcores() only maintains the different power
states only for CPU suspend/resume flow, so it cannot return correct
states for CPU on/off flow.
This patch is to change use hisi_test_cpu_down() to check if all CPUs
have been powered off, so that can power off the whole cluster properly
when all CPUs in cluster have been hotplugged off.
Signed-off-by: Tao Wang <kevin.wangtao@hisilicon.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
The ARM_PLAT_MT bit enables the support for MT bit in
MPIDR format. This means that the level 0 affinity
represents the thread and CPU / Cluster levels are
at affinity level 1 and 2 respectively.
This was not catered for in the scpi 'css_scp_get_power_state, API.
Since the SCPI driver can only cater for single threaded CPUs,
this patch fixes the problem by catering for this shift by
effectively ignoring the Thread (level 0) affinity level.
Change-Id: If44f55c9fb2773c8d3f8a9bbcf5420a6f7409dfe
Signed-off-by: jagadeesh ujja <jagadeesh.ujja@arm.com>
davidcunado-arm
Jorge Ramirez-Ortiz
Isla Mitchell
Victor Chong
Haojian Zhuang
Ziyuan Xu
Soren Brinkmann
Caesar Wang
Soby Mathew
danh-arm
Dimitris Papastamos
Douglas Raillard
Masahiro Yamada
Leo Yan
jagadeesh ujja