Add debug log for the maximum supported INTID of SPI and eSPI on the
current GIC implementation.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Ie45ab1d85b39658c4ca4bc54ee433ac44e41d03f
The GICv3 architecture allows GICD_TYPER.ITLinesNumber to be 31, so
the maximum possible value for num_ints is 1024. The value must be
limited to (MAX_SPI_ID + 1), or GICD_OFFSET() will consider it as ESPI
INTID and return wrong register address.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Iddcb83d3e5d241b39f4176c19c2bceaa2c3dd653
In function gicv3_spis_config_defaults(), the variable num_ints is set
to (maximum SPI INTID + 1), while num_eints is set to (maximum ESPI
INTID). It introduces not only inconsistency to the code, but also
logical bug in the "for" loops, for the INTID of num_eints is also
valid and the check should be inclusive.
Fix this by setting num_eints to (maximum ESPI INTID + 1) as well.
Fix similar issues in gicv3_distif_save() and
gicv3_distif_init_restore().
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I4425777d17e84e85f38853603340bd348640154f
RESTORE/SAVE_GICD_EREGS uses (int_id - (MIN_ESPI_ID - MIN_SPI_ID)) to
get the context array index for ESPI, which will override the space of
standard SPI starting from (MIN_SPI_ID + MIN_SPI_ID).
However, using TOTAL_SPI_INTR_NUM to replace the above MIN_SPI_ID
cannot totally fix the issue, for TOTAL_SPI_INTR_NUM is not well
aligned and the array index will be rounded down by the shifting
operation if being shifted more than 2 bits. It will cause buffer
override again when the existing maximum SPI reaches 1019.
So round up TOTAL_SPI_INTR_NUM with (1 << REG##R_SHIFT) for GICD
context arrays.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I5be2837c42f381a62f8d46a4ecd778009b1fe059
In function gicv3_rdistif_probe(), line #1322 implies
gicv3_driver_data->mpidr_to_core_pos() may be null, but the original
code uses this interface to get current CPU index unconditionally.
It is better to use MPIDR to probe GICR which does not depend on
gicv3_driver_data->mpidr_to_core_pos().
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I64add055385040fe0a56b977e2299608e2309a6e
This patch does not change code, it only updates comments and macro name
for 6th bit of Status Register. So TF-A binary stay same.
6th bit of the Status Register is named TX EMPTY and is set to 1 when both
Transmitter Holding Register (THR) or Transmitter Shift Register (TSR) are
empty. It is when all characters were already transmitted.
There is also TX FIFO EMPTY bit in the Status Register which is set to 1
only when THR is empty.
In both console_a3700_core_init() and console_a3700_core_flush() functions
we should wait until both THR and TSR are empty therefore we should check
6th bit of the Status Register.
So current code is correct, just had misleading macro names and comments.
This change fixes this "documentation" issue, fixes macro name for 6th bit
of the Status Register and also updates comments.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I19e4e7f53a90bcfb318e6dd1b1249b6cbf81c4d3
Implementation is simple, just check if there is a pending character in
RX FIFO via RXRDY bit of Status Register and if yes, read it from
UART_RX_REG register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I226b6e336f44f5d0ca8dcb68e49a68e8f2f49708
Add pin control support for RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I08719015cab1ec59e2270523980a0a3e26e72c01
Add support for initializing DRAM on RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I99f1a6971a061a44687af498d55306a93e4fc8f7
Move DDR/QoS/PFC header files, so that the same code
can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I2cc0ceda8d05b6b8d95a69afdc233dc0d098e850
Move rpc driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I04805d720d95b8edcc14e652f897fadc7f432197
Move avs driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I85d9fa8b6abf158ce2521f1696478f7c5339fc42
Move authentication driver code to common directory, so that the
same code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I02592dfc714998bf89b9feaa78f685ae36be6f59
Move dma driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Idce2e2f4e098cfc17219f963373d20ebf74e5b7c
Move watch driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I235f2cde325a0feeadbfc4b7ee02e8b1186f7ea1
Move rom driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I399dfb5eff186db76d26fa9c54bea88bee66789c
Move delay driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I5e806bd0e0a0a4b436048513b7089db90ff9805f
Move console/scif driver code to common directory, so that the
same code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I0b15e4f4ffaaa99e77bcee32b1dad648eeadcd9b
Move pwrc driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I75d91a44d872fe2296b15c700efacd5721385363
Move io driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ic661e415c91a1fbfd5eee3bba86466037e51574b
Move eMMC driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I7f3055709337327d1a1c9f563c14ad1626adb355
Move plat common sources to common directory, so that same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Id2b1822c97cc50e3febaffc2e5f42b4d53809a17
Create a common directory and move the header and assembly files
so that the common code can be used by both Renesas R-Car Gen3 and
RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ia9a563a1c3c9f8c6f0d3cb82622deb2e155d7f6c
Write char if fifo is empty. If this is done like this all chars are
printed. Because origin code just put that chars to fifo and in case of
reset messages were missing.
Before this change chars are put to fifo and only check before adding if
fifo is full. The patch is changing this logic that it is adding char only
when fifo is empty to make sure that in case of reset (by another SW for
example) all chars are printed. Maybe one char can be missed but for IP
itself it is much easier to send just one char compare to full fifo.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Ic24c2c1252bce24be2aed68ee29477ca4a549e5f
This patch fixes checkpatch warnings and arrange header
as per TF-A coding style.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I46cd4d9b2851202324fe714e776cf3ad2ee1d923
Sort the headers alphabetically and replace TAB with a space
after #define.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I07c358294b7c02cbfa360112bbbde0eb5f2b50f5
This patches fixes checkpatch warnings, replace TAB with space
after #define macros and arrange header as per TF-A coding style.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Iba009587e0b499b3ae58876be390602ae14175b2
Fix checkpatch warnings.
There are no functional changes.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Iec7dd019bd38e84eccd8cc17189745fdef1911bb
This patch fixes the below checkpatch warnings
Line 13: WARNING: please, no spaces at the start of a line
Line 15: WARNING: please, no spaces at the start of a line
Line 18: WARNING: Missing a blank line after declarations
Line 24: WARNING: please, no spaces at the start of a line
Line 26: WARNING: please, no spaces at the start of a line
Line 29: WARNING: Missing a blank line after declarations
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I41d146e86889640d11e88c0717039353ddceff0d
Fix checkpatch warnings.
There are no functional changes.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ic7406aa88e121914270a8d192f170c9c4244578a
Use space instead of TAB after #define's. Also updated
header files as per TF-A coding style.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I4eac94f0bc79f24b8ac7165ec48f1e1de95d7205
Replace TAB with space after #define macros and update comments as per
TF-A coding style.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Iff46838a41f991f7dd9dc6fb043e9e482ea0b11d
Sort the header includes alphabetically, fix typos and drop unneeded TAB
and replace it with space
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I62e2658b0309c0985dd32ff023b8b16bd7f2be8e
Implementation is simple, just wait for the TX FIFO to be empty.
Without this patch TF-A on A3720 truncate the last line:
NOTICE: BL31: Built : 16:1
With this patch TF-A on A3720 print correctly also the last line:
NOTICE: BL31: Built : 19:03:31, Dec 23 2020
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I2f2ea42beab66ba132afdb400ca7898c5419db09
Fix checkpatch warnings and MISRA defects.
There are no functional changes.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I349a8eaa7bd6182746ba5104ee9fe48a709c24fd
The BL31 log driver is registered before the xlat tables are initialized,
at that point the log memory is configured as device memory and can only
be accessed with up-to-32bit aligned accesses. Adjust the driver to do
just that.
The memset() call has to be replaced by a loop of 32bit writes to the log,
the memcpy() is trivial to replace with a single 32bit write of the entire
TLOG word. In the end, this even simplifies the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Ie9152e782e67d93e7236069a294df812e2b873bf
* changes:
docs: update STM32MP1 with versions details
stm32mp1: get peripheral base address from a define
stm32mp1: add finished good variant in board identifier
Retrieve peripheral base address from a define instead of
parsing the device tree. The goal is to improve execution time.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I2588c53ad3d4abcc3d7fe156458434a7940dd72b
Usually, C has no problem up-converting types to larger bit sizes. MISRA
rule 10.7 requires that you not do this, or be very explicit about this.
This resolves the following required rule:
bl1/aarch64/bl1_context_mgmt.c:81:[MISRA C-2012 Rule 10.7 (required)]<None>
The width of the composite expression "0U | ((mode & 3U) << 2U) | 1U |
0x3c0U" (32 bits) is less that the right hand operand
"18446744073709547519ULL" (64 bits).
This also resolves MISRA defects such as:
bl2/aarch64/bl2arch_setup.c:18:[MISRA C-2012 Rule 12.2 (required)]
In the expression "3U << 20", shifting more than 7 bits, the number
of bits in the essential type of the left expression, "3U", is
not allowed.
Further, MISRA requires that all shifts don't overflow. The definition of
PAGE_SIZE was (1U << 12), and 1U is 8 bits. This caused about 50 issues.
This fixes the violation by changing the definition to 1UL << 12. Since
this uses 32bits, it should not create any issues for aarch32.
This patch also contains a fix for a build failure in the sun50i_a64
platform. Specifically, these misra fixes removed a single and
instruction,
92407e73 and x19, x19, #0xffffffff
from the cm_setup_context function caused a relocation in
psci_cpus_on_start to require a linker-generated stub. This increased the
size of the .text section and caused an alignment later on to go over a
page boundary and round up to the end of RAM before placing the .data
section. This sectionn is of non-zero size and therefore causes a link
error.
The fix included in this reorders the functions during link time
without changing their ording with respect to alignment.
Change-Id: I76b4b662c3d262296728a8b9aab7a33b02087f16
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Chip select is retrieved from device tree and check
must be done regarding the MAX_CS defined.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Reviewed-by: Christophe KERELLO <christophe.kerello@st.com>
Change-Id: I03144b133bd51a845a4794f0f6bbd9402fc04936
FMC node bindings are modified to add EBI controller node.
FMC driver and associated device tree files are modified
to support these new bindings.
Change-Id: I4bf201e96a1aca20957e0dac3a3b87caadd05bdc
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
In the function gicv2_set_spi_routing, the signed value proc_num is cast
to unsigned int before being compared to other unsigned values in two
assert calls. The value proc_num can be a negative value, and once the
negative value is cast to unsigned it becomes a very large number which
will trigger the assert. This patch changes the assert cast so that the
unsigned values are cast to signed instead, keeping the same functionality
but allowing proc_num to be negative.
This bug can be seen when running the SDEI RM_ANY routing mode test in
TFTF on the Juno platform.
This patch also makes the usage of the proc_num variable in other gicv2
functions more clear.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: If1b98eebb00bd9b73862e5e995e5e68c168170a6
And from crash_console_flush.
We ignore the error information return by console_flush in _every_
place where we call it, and casting the return type to void does not
work around the MISRA violation that this causes. Instead, we collect
the error information from the driver (to avoid changing that API), and
don't return it to the caller.
Change-Id: I1e35afe01764d5c8f0efd04f8949d333ffb688c1
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Clear interrupt flag register after each sector read to avoid
issue when checking the register status.
Without clearing the interrupt, the status read doesn't wait
properly the ready bit.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: If290e3f165b986f0e736bb1b5e4d3dad4b749d74
The polarity inversion for USB was not tested due to lack of hw design
which requires it. Currently all supported boards doesn't require USB
phy polarity inversion, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards. Enable the option for the ones that need it.
Change-Id: Ia5f2ee313a93962e94963e2dd8a759ef6d9da369
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The cp110 comphy has ability to invert RX and/or TX polarity. Polarity
depends on board design. Currently all supported boards doesn't require
SATA phy polarity invert, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards.
Change-Id: Ifd0bc6aaf8a76a0928132b197422f3193cf020d5
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
According to erratum IPCE_COMPHY-1353 the TX_IDLE bit should
be toggled in addition to the XFI/SFI PHY reset.
Change-Id: Idd2c2abfcb2f960caa01e6d69db524c2e4734f50
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Do not force non-secure access level for PIDI masters when LLC_SRAM
is enabled. The EIP197 is located on CP0 and need to access secure
SRAM in AP LLC. This requires EIP197 DMA to have AXPROT[1]=0 and not
changed when forwarded to address decoding tables.
Change-Id: I8962db94a124350c14220ba6d0364d294ae4664a
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Added ccu window to allow access to addresses
in the range [0xf100_0000, 0xf1ff_ffff].
Change-Id: I63ee68338d674114d01cd627198dc907653493e8
Signed-off-by: Alex Leibovich <alexl@marvell.com>
This patch migrates the mbedcrypto dependency for TF-A
to mbedTLS repo v2.24.0 which is the latest release tag.
The relevant documentation is updated to reflect the
use of new version.
Change-Id: I116f44242e8c98e856416ea871d11abd3234dac1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
A GICv3 interrupt controller will be instantiated for a certain number
of cores. This will result in the respective number of GICR frames. The
last frame will have the "Last" bit set in its GICR_TYPER register.
For platforms with a topology unknown at build time (the Arm FPGAs, for
instance), we need to learn the number of used cores at runtime, to size
the GICR region in the devicetree accordingly.
Add a generic function that iterates over all GICR frames until it
encounters one with the "Last" bit set. It returns the number of cores
the GICv3 has been configured for.
Change-Id: I79f033c50dfc1c275aba7122725868811abcc4f8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
MCKPROT hardening in RCC mandates that both bits RCC[TZEN] and
RCC[MCKPROT] are enabled. This change fixes stm32mp1_rcc_is_mckprot()
to check both bits, not RCC[MCKPROT] only.
This change also updates stm32mp1_rcc_is_secure() for consistency.
Change-Id: If1f07babdcb5677906ddbf974d9dc17255d4e174
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The ICR static flags are cleared before sending a command.
The SDMMC_DCTRLR register is set to 0 if no data is expected on a given
command or on the next command in case of CMD55.
Change-Id: I5ae172a484218f53160e98b3684967c6960475a6
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The retries number should be 3.
A warning message is added in mmc_block_read(), and the code is refactored.
Change-Id: I577c7dd91c451c7580b1660042cb5fe26ee3fa12
Signed-off-by: Yann Gautier <yann.gautier@st.com>
nand_wait_ready is called with a millisecond delay
but the timeout used a micro second. Fixing the conversion
in the timeout call.
The prototype of the function is also changed to use an unsigned int
parameter.
Change-Id: Ia3281be7980477dfbfdb842308d35ecd8b926fb8
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change the detection message from WARN to INFO when macronix
NOR is detected.
Change-Id: I488696f1fb75b823e85decfcd6cd32e7b36a6c2e
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The call to fdt_get_status(node) has to be done after the DT is found
to be valid.
Fixes: 1fc2130c5 stm32mp1: update device tree and gpio functions
Change-Id: I70f803aae3dde128a9e740f54c8837b64cb1a244
Signed-off-by: Yann Gautier <yann.gautier@st.com>
While restarting a new hash computation, STR register
is not cleared. It needs to be written before each
computation.
Change-Id: If65902dd21f9c139ec5da3ca87721232f73710db
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Builds in Debug mode with Measured Boot enabled might run out of trusted
SRAM. This patch allows to change the Log Level at which the Measured Boot
driver will dump the event log, so the latter can be accessed even on
Release builds if necessary, saving space on RAM.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I133689e313776cb3f231b774c26cbca4760fa120
Loop macros make it easier for developers to include new variables to
assert or define and also help code code readability on makefiles.
Change-Id: I0d21d6e67b3eca8976c4d856ac8ccc02c8bb5ffa
Signed-off-by: Leonardo Sandoval <leonardo.sandoval@linaro.org>
The DRIVEVBUS power rail of the AXP803 PMIC is mostly used to supply
the USB bus power on micro USB sockets, when used in host mode. As this
is a dynamic operation, and mostly we want micro USB sockets to act in
client mode initially, BL31 should not actually enable this power line.
However, on some boards DRIVEVBUS is used to supply power to normal
USB-A sockets. Failing to activate this line there results in
non-functional USB in U-Boot on those boards.
For that reason we were enabling DRIVEVBUS so far, as it did not seem to
cause any harm to the other boards. However it turns out that on the
Pinephone (and other systems with a battery), actually enabling DRIVEVBUS
unconditionally causes serious problems (reboot loop).
To accommodate both use cases, without reverting to a build time option,
check the default OTG configuration in the devicetree. For boards with
USB-A sockets this is set to "host", on boards with micro-B sockets to
"otg". Depending on this setting, we either enable DRIVEVBUS or leave it
alone.
This fixes TF-A on the Pinephone and potentially other battery powered
devices.
Change-Id: Iec0e07f218b2b4393bf4e05c3386261f8ed19e9f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For dualroot CoT there are two sets of SP certificates, one owned by
Silicon Provider(SiP) and other owned by Platform. Each certificate can
have a maximum of 4 SPs.
This patch reduces the number of SiP owned SPs from 8 to 4 and adds
the remaining 4 to Plat owned SP.
Plat owned SP certificate is signed using Platform RoT key and
protected against anti-rollback using the Non-trusted Non-volatile
counter.
Change-Id: Idc3ddd87d6d85a5506a7435f45a6ec17c4c50425
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
ERRATA ID: RES-3033912 - Internal Address Space Init state causes
a hang upon accesses to [0xf070_0000, 0xf07f_ffff]
Workaround: Boot Firmware (ATF) should configure CCU_RGF_WIN(4) to
split [0x6e_0000, 0xff_ffff] to values [0x6e_0000, 0x6f_ffff] and
[0x80_0000, 0xff_ffff] that cause accesses to the segment of
[0xf070_0000, 0xf07f_ffff] to act as RAZWI. Reuse common
work-around code for both AP806 and AP807.
Change-Id: Ia91a4802d02917d1682faa0c81571093d1687d97
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Currently only single signing domain is supported for SP packages but
there is plan to support dual signing domains if CoT is dualroot.
SP_CONTENT_CERT_ID is the certificate file which is currently generated
and signed with trusted world key which in-turn is derived from Silicon
provider RoT key.
To allow dual signing domain for SP packages, other certificate file
will be derived from Platform owned RoT key.
This patch renames "SP_CONTENT_CERT_ID" to "SIP_SP_CONTENT_CERT_ID" and
does other related changes.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I0bc445a3ab257e2dac03faa64f46e36a9fed5e93
This patch fixes defects 10.3, 10.4, 10.7, 20.7
reported by MISRA-2012 scan and adds braces for
conditional statements according to the TF-A
coding style.
Change-Id: If84ed31cdd55bc8e7cdd2a5f48c0dacc25792112
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
* changes:
plat/arm/board/fvp: Add support for Measured Boot
TF-A: Add support for Measured Boot driver to FCONF
TF-A: Add support for Measured Boot driver in BL1 and BL2
TF-A: Add Event Log for Measured Boot
TF-A: Add support for Measured Boot driver
This patch adds support for Event Log generation required
for Measured Boot functionality.
Change-Id: I34f05a33565e6659e78499d62cc6fb00b7d6c2dc
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
The Arm GIC-Clayton IP has the same power management requirements as
the GIC-600, when it comes to powering up the redistributors before
using them.
Add the IIDR value to the existing list of implementations requiring
the power sequence.
Change-Id: Ib965dfe278c40a4fff94f65a8d445c27a2ae6fd2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch moves all GICv2 driver files into new added
'gicv2.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
NOTE: Usage of 'drivers/arm/gic/common/gic_common.c' file
is now deprecated and platforms with GICv2 driver need to
be modified to include 'drivers/arm/gic/v2/gicv2.mk' in
their makefiles.
Change-Id: Ib10e71bdda0e5c7e80a049ddce2de1dd839602d1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
The cause of failure is not memory shortage.
The comment for ENFILE in include/lib/libc/errno.h
/* Too many open files in system */
... is a better match to the warning message here.
Change-Id: I45a1740995d464edd8b3e32b93f1f92ba17e5874
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Heyi Guo
Madhukar Pappireddy
Manish Pandey
Peng Fan
Pali Rohár
Biju Das
Michal Simek
Marek Vasut
Joanna Farley
Mark Dykes
Yann Gautier
Jimmy Brisson
Lionel Debieve
Christophe Kerello
johpow01
Grzegorz Jaszczyk
Marcin Wojtas
Konstantin Porotchkin
Alex Leibovich
Alexei Fedorov
Andre Przywara
Etienne Carriere
Javier Almansa Sobrino
Leonardo Sandoval
Stefan Chulski
Bharat Gooty
Masahiro Yamada