To catch early hangs in resume, this sets up the watchdog before
anything else in the pmusram code (ignoring setting up the stack...).
This uses hard coded settings for the watchdog until the proper
watchdog restore later on in the firmware/kernel.
This also restores the old watchdog register values before the PLLs
are restored to make sure we don't temporarily switch over to a 1/3s
timeout on the watchdog when the pclk_wdt goes from 4MHz to 100MHz.
Change-Id: I8f7652089a88783271b17482117b4609330abe80
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
All the m0 code run in SRAM before, but we need to watch PMU_POWER_ST
when SOC enter into FSM, and SRAM will shutdown during this time, so
this code need run in PMUSRAM. But PMUSRAM only 8K space, we can not
put all the m0 binary into PMUSRAM, Split the M0 binary into two, dram
part still run in SRAM, and suspend part run in PMUSRAM.
Change-Id: Ie08bdf3e2b8838f12b9297fe60ab0aad219684b1
Signed-off-by: Lin Huang <hl@rock-chips.com>
we need to enable PMU_WKUP_RST_EN for pmu powermode configure, since
enable wakeup reset will hold the soc status, so the SOC will not affect
by some power or other single glitch when resume, and keep the soc in the
right status. And it not need to enable DDRIO_RET_HW_DE_REQ, the ddr resume
will do it manual.
Change-Id: Ib4af897ffb3cb63dc2aa9a6002e5d9ef86ee4a49
Signed-off-by: Lin Huang <hl@rock-chips.com>
SGI-575's NSRAM is neither in the same place nor the same size as Juno's.
Change-Id: Id6d692e9c7e9c1360014bb525eda966ebe29c823
Signed-off-by: Chris Kay <chris.kay@arm.com>
Normally, BL33 needs to contain a boot loader like U-Boot or UEFI that
eventually gives control to the OS. However, in some cases, this boot
sequence may be too slow. For example, when doing tests in a
cycle-accurate emulator, the user may only be interested in the
interaction between the Trusted Firmware and the OS, not in the boot
process itself.
The new option ARM_LINUX_KERNEL_AS_BL33 allows BL33 to contain the Linux
kernel image by changing the value of registers x0-x3 to the values
expected by the kernel. This option requires the device tree blob (DTB)
to be present in memory. Its address must be specified in the newly
introduced ARM_PRELOADED_DTB_BASE build option. For now, it only supports
AArch64 kernels.
This option is only available when RESET_TO_BL31=1. For this reason
the BL33 binary must be preloaded in memory and PRELOADED_BL33_BASE must
be used.
For example, if the kernel is loaded at 0x80080000 and the DTB is loaded
at address 0x82000000, the firmware could be built like this:
CROSS_COMPILE=aarch64-linux-gnu- \
make PLAT=fvp DEBUG=1 \
RESET_TO_BL31=1 \
ARM_LINUX_KERNEL_AS_BL33=1 \
PRELOADED_BL33_BASE=0x80080000 \
ARM_PRELOADED_DTB_BASE=0x82000000 \
all fip
Change-Id: If9dc847c65ae2d0c27b51f0fd44fc06b28497db9
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The old API is deprecated and will eventually be removed.
Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.
The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.
Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.
The size of BL31 has been increased in builds with SPM.
Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
- Assign 0x10 for RAS exceptions on ARM platforms, and install
EHF priority descriptor.
- Call the common RAS initialisation from ARM BL31 setup.
- Add empty definitions for platform error records and RAS interrupts.
Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Previous patches added frameworks for handling RAS errors. This patch
introduces features that the platform can use to enumerate and iterate
RAS nodes:
- The REGISTER_RAS_NODES() can be used to expose an array of
ras_node_info_t structures. Each ras_node_info_t describes a RAS
node, along with handlers for probing the node for error, and if
did record an error, another handler to handle it.
- The macro for_each_ras_node() can be used to iterate over the
registered RAS nodes, probe for, and handle any errors.
The common platform EA handler has been amended using error handling
primitives introduced by both this and previous patches.
Change-Id: I2e13f65a88357bc48cd97d608db6c541fad73853
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
At present, any External Abort routed to EL3 is reported as an unhandled
exception and cause a panic. This patch enables ARM Trusted Firmware to
handle External Aborts routed to EL3.
With this patch, when an External Abort is received at EL3, its handling
is delegated to plat_ea_handler() function. Platforms can provide their
own implementation of this function. This patch adds a weak definition
of the said function that prints out a message and just panics.
In order to support handling External Aborts at EL3, the build option
HANDLE_EA_EL3_FIRST must be set to 1.
Before this patch, HANDLE_EA_EL3_FIRST wasn't passed down to
compilation; this patch fixes that too.
Change-Id: I4d07b7e65eb191ff72d63b909ae9512478cd01a1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.
The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.
Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Since commit 031dbb1224 ("AArch32: Add essential Arch helpers"),
it is difficult to use consistent format strings for printf() family
between aarch32 and aarch64.
For example, uint64_t is defined as 'unsigned long long' for aarch32
and as 'unsigned long' for aarch64. Likewise, uintptr_t is defined
as 'unsigned int' for aarch32, and as 'unsigned long' for aarch64.
A problem typically arises when you use printf() in common code.
One solution could be, to cast the arguments to a type long enough
for both architectures. For example, if 'val' is uint64_t type,
like this:
printf("val = %llx\n", (unsigned long long)val);
Or, somebody may suggest to use a macro provided by <inttypes.h>,
like this:
printf("val = %" PRIx64 "\n", val);
But, both would make the code ugly.
The solution adopted in Linux kernel is to use the same typedefs for
all architectures. The fixed integer types in the kernel-space have
been unified into int-ll64, like follows:
typedef signed char int8_t;
typedef unsigned char uint8_t;
typedef signed short int16_t;
typedef unsigned short uint16_t;
typedef signed int int32_t;
typedef unsigned int uint32_t;
typedef signed long long int64_t;
typedef unsigned long long uint64_t;
[ Linux commit: 0c79a8e29b5fcbcbfd611daf9d500cfad8370fcf ]
This gets along with the codebase shared between 32 bit and 64 bit,
with the data model called ILP32, LP64, respectively.
The width for primitive types is defined as follows:
ILP32 LP64
int 32 32
long 32 64
long long 64 64
pointer 32 64
'long long' is 64 bit for both, so it is used for defining uint64_t.
'long' has the same width as pointer, so for uintptr_t.
We still need an ifdef conditional for (s)size_t.
All 64 bit architectures use "unsigned long" size_t, and most 32 bit
architectures use "unsigned int" size_t. H8/300, S/390 are known as
exceptions; they use "unsigned long" size_t despite their architecture
is 32 bit.
One idea for simplification might be to define size_t as 'unsigned long'
across architectures, then forbid the use of "%z" string format.
However, this would cause a distortion between size_t and sizeof()
operator. We have unknowledge about the native type of sizeof(), so
we need a guess of it anyway. I want the following formula to always
return 1:
__builtin_types_compatible_p(size_t, typeof(sizeof(int)))
Fortunately, ARM is probably a majority case. As far as I know, all
32 bit ARM compilers use "unsigned int" size_t.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 4c0d039076 ("Rework type usage in Trusted Firmware") changed
the type usage in struct declarations, but did not touch the definition
side. Fix the type mismatch.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
SGI-575 platform is based on Cortex-A75 processor which has its MT bit
in the MPIDR register set to '1'. So the Arm platform layer code has
to be made aware of this.
Signed-off-by: Sudipto Paul <sudipto.paul@arm.com>
Currently the SCMI driver supports MHUv1, but Arm platforms may have
varied versions of MHU driver, with MHUv2 controllers being in the
latest Arm platforms.
This patch updates the SCMI driver to support MHUv2, specifically that
the sender must send the wake-up to the receiver before initiating any
data transfer.
Also, the existing mhu driver files, css_mhu.c and css_mhu.h, have been
moved from the scpi directory to a new directory, css/drivers/mhu.
Change-Id: I9b46b492a3e1d9e26db12d83a9773958a8c8402f
Signed-off-by: Samarth Parikh <samarth.parikh@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp SPD=tspd TRUSTED_BOARD_BOOT=1 \
GENERATE_COT=1 ARM_ROTPK_LOCATION=devel_rsa \
ROT_KEY=arm_rotprivk_rsa.pem MBEDTLS_DIR=mbedtls all
Change-Id: Ie4cd6011b3e4fdcdd94ccb97a7e941f3b5b7aeb8
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp SPD=tspd all
Change-Id: I0a16cf68fef29cf00ec0a52e47786f61d02ca4ae
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.3: All declarations of an object or function shall
use the same names and type qualifiers.
Fixed for:
make DEBUG=1 PLAT=juno LOG_LEVEL=50 all
Change-Id: I0e4a03a0d2170cb1c632e079112a972091994a39
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I32b223251b8bf5924149d89431a65d3405a73d3e
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Fix that DDR can't work at 533MHz. Now step to set DDR frequency
from 150MHz to 800MHz. DDR could work among these frequency, 150MHz,
266MHz, 400MHz, 533MHz and 800MHz.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Add TZMP1 support on Juno and increase the BL2 size accordingly due to the
extra data structures to describe the TZC regions and the additional code.
Signed-off-by: Summer Qin <summer.qin@arm.com>
This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.
This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>
This patch introduce TF-A support for NXP's ls1043a platform.
more details information of ls1043a chip and ls1043ardb board
can be found at docs/plat/ls1043a.rst.
Boot sequence on ls1043a is: bootrom loads bl1 firstly, then bl1
loads bl2, bl2 will load bl31, bl32 and bl33, bl31 will boot
bl32(tee os) and bl33(u-boot or uefi), bl33 boot Linux kernel.
Now TF-A on ls1043ardb platform has the following features in this patch:
* Support boot from Nor flash.
* TF-A can boot bl33 which runs in el2 of non-secure world.
* TF-A boot OPTee OS.
* Support PSCI
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Chenyin.Ha <Chenyin.Ha@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: jiaheng.fan <jiaheng.fan@nxp.com>
Signed-off-by: Wen He <wen.he_1@nxp.com>
Building TBBR(SPD=opteed) and non-TBBR TF-A images is breaking for
Juno for different configurations listed below:
* Overflow error of 4096 bytes for rsa algorithm.
* Overflow error of 8192 bytes for ecdsa algorithm.
* Overflow error of 4096 bytes for rsa+ecdsa algorithm.
* Overflow error of 4096 bytes for non-TBBR case.
So this patch increments macro PLAT_ARM_MAX_BL2_SIZE for all the above
cases accordingly.
Change-Id: I75ec6c0a718181d34553fe55437f0496f467683f
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
This fixes an off by 576x bug the the sram_udelay code. The wrong
value was multipled by the system ticks per mhz value (which is 24),
so we delayed for 1/576th of the requested time.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
The current AArch32 version of plat_arm_calc_core_pos uses an incorrect
algorithm to calculate the linear position of a core / PE from its
MPIDR.
This patch corrects the algorithm to:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId
which supports cores where there are more than 1 PE per CPU.
NOTE: the AArch64 version was fixed in 39b21d1
Change-Id: I72aea89d8f72f8b1fef54e2177a0fa6fef0f5513
Signed-off-by: David Cunado <david.cunado@arm.com>
Use the console_pl011_core_* functions directly in the crash console
callbacks.
This bypasses the MULTI_CONSOLE_API for the crash console (UART1), but
allows using the crash console before the C runtime has been initialized
(eg to call ASM_ASSERT). This retains backwards compatibility with respect
to functionality when the old API is used.
Use the MULTI_CONSOLE_API to register UART0 as the boot and runtime
console.
FixesARM-software/tf-issues#572
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
Add support for System Guidance for Infrastructure platform SGI575.
Change-Id: I0125c2ed4469fbc8367dafcc8adce770b6b3147d
Signed-off-by: Nariman Poushin <nariman.poushin@linaro.org>
If system is still accessing storage device, reboot operation
may cause data broken. So add the flush and delay operation
before system reset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Void pointers have been used to access linker symbols, by declaring an
extern pointer, then taking the address of it. This limits symbols
values to aligned pointer values. To remove this restriction an
IMPORT_SYM macro has been introduced, which declares it as a char
pointer and casts it to the required type.
Change-Id: I89877fc3b13ed311817bb8ba79d4872b89bfd3b0
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>
Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.
The crash console doesn't use this API, it uses internally the core
functions of the 16550 console.
`bl31_plat_runtime_setup` is no longer needed. When this platform port
was introduced, that function used to disable the console. It was needed
to override that behaviour. The new behaviour is to switch to the
runtime console. The console is registered for all scopes (boot, crash
and runtime) in `rpi3_console_init` so it is not needed to override the
default behaviour anymore.
Update documentation.
Change-Id: If2ee8f91044216183b7ef142e5c05ad6220ae92f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Removes fall-through in switch statement on unknown interrupt type in
release builds.
Previous behaviour was to assert(0) on default case in debug builds but
fall through and interpret the unknown interrupt type as
INTR_TYPE_EL3 in release builds.
Change-Id: I05fb0299608efda0f9eda2288d3e56e5625e05c9
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>
Add crash_console_init declaration to console.h
Only enable MULTI_CONSOLE_API for AArch64
FixesARM-software/tf-issues#571
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
Add support for the new MULTI_CONSOLE_API
Crash information is now displayed in both the runtime and crash consoles,
if a crash occurs after the runtime console has been enabled
Enable MULTI_CONSOLE_API by default on qemu builds
FixesARM-software/tf-issues#561
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
When the source code says 'SMCC' it is talking about the SMC Calling
Convention. The correct acronym is SMCCC. This affects a few definitions
and file names.
Some files have been renamed (smcc.h, smcc_helpers.h and smcc_macros.S)
but the old files have been kept for compatibility, they include the
new ones with an ERROR_DEPRECATED guard.
Change-Id: I78f94052a502436fdd97ca32c0fe86bd58173f2f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Allow qemu users to enable stack protection. Since the virt platform
does not provide an RNG, use a basic, timer-based, canary generation,
similarly to FVP.
Increase SRAM size and BL2 size to fit images when stack protection is
enabled.
Notice that stack protection is not enabled by default in qemu.
FixesARM-software/tf-issues#568
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
there are two fix for save/restore watchdog register:
1. watchdog plck will shutdown after secure_watchdog_disable(), so need
to save register before it and restore after secure_watchdog_enable().
2. need write 0x76 to cnt_restart to keep watchdog alive when restore
watchdog register.
Change-Id: I1f6fbceae22186e3b72a87df6332a110adf37479
Signed-off-by: Lin Huang <hl@rock-chips.com>
x3 will be assigned by the folloing instructions.
So the first instruction is not needed any more.
old method:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER)
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId
it should be
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId
which can be simplified as:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER + CPUId) * FVP_MAX_PE_PER_CPU + ThreadId
Signed-off-by: Wang Feng <feng_feng.wang@spreadtrum.com>
Existing database allows to set only single mode for SDIO.
SDIO can have different groups (8 bit, 4 bit and 1 bit).
As there is only single SDIO group in each pin, it is not
possible to use different mode groups for SDIO.
Extend database in generic way to allow multiuple function
groups in single pin. Add different SDIO groups to pins and
create separate functions for each modes.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Define default DDR location to which ATF has to compiled
if DEBUG option is enabled. This is required now, as the ATF cant fit
in OCM with DEBUG option enabled. The default value is 0x1000 and can be
used till 0x7ffff. User can still override as per wish/requirement
using current commandline options.
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add pin control APIs which driver can use to query
pin information from firmware. Using these APIs,
driver do not need to maintain hard-coded pin database.
Major changes in patch are:
- Add pin database with pins, functions and function groups
information
- Implement APIs for pin information queries
- Update pin control APIs for get/set functions to use new
pin control database. Remove pin database which was added
earlier.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add IOCTLs to read/write global general storage and
persistent global general storage registers access.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
- Add clock entries and information to clock database.
- Implement APIs to provide clock topology and other
information to caller.
- Implement APIs to control clocks and PLLs.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
These are empty functions with no logic right now. Code
will be added in subsequent commits.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement ioctl APIs which uses MMIO operations
to configure devices. Below IOCTLs are supported
in this patch:
* Set tap delay bypass
* Set SGMII mode
* SD reset
* Set SD/MMC tap delay
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement ioctl APIs which uses MMIO operations
to control RPU operations. Below IOCTLs are supported
in this patch:
* Get RPU operation mode
* Set RPU operation mode
* Configure RPU boot address (OCM/TCM)
* Configure TCM combined mode
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement pin control APIs which uses MMIO operations
to set/get values of configuration parameters.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement pin control APIs which uses MMIO operations
to set/get functions for the given pin.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add wrappers for pin control APIs. Actual implementation of
these APIs would be done in subsequent changes.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add new function and node IDs supported by PMUFW in
function list and node list respectively.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
The FVP platform port for SP_MIN (BL32) didn't map the flash memory
in BL32 for stroring the mem_protect enable state information leading
to synchronous exception. The patch fixes it by adding the region to
the BL32 mmap tables.
Change-Id: I37eec83c3e1ea43d1b5504d3683eebc32a57eadf
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>
Boot memory layout is specific for a platform, but should not be
mixed up with other platform specific attributes. A separate file is
much cleaner and better to compare with other platforms. Take a look
at plat/poplar where it is done the same way.
Moved hikey_def.h to system include folder and moved includes from
hikey_def.h to more general platform_def.h.
Signed-off-by: Michael Brandl <git@fineon.pw>
Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.
In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.
Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.
Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This issue was detected when testing FWU on Juno. The Timer
`timer_ops` was not being initialized before being used by
the SDS driver on Juno. This patch adds the call to
`generic_delay_timer_init()` during bl2u_early_platform_setup().
This is done generically for all ARM platforms because the
cost involved is minimal.
Change-Id: I349cf0bd1db68406eb2298b65f9c729f792cabdc
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
plat/hisilicon/hikey/hikey_bl1_setup.c:565:47:
error: value size does not match register size specified by the
constraint and modifier [-Werror,-Wasm-operand-widths]
__asm__ volatile ("mrs %0, cpacr_el1" : "=r"(data));
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
It's unnecessary to call platform driver initialization in image
load driver. We could make bl2_platform_setup() to executing
just before SCP_BL2 by setting flag IMAGE_ATTRIB_PLAT_SETUP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since non-TF ROM is used in HiKey960 platform (Hisilicon Hi3660 SoC),
replace BL1 by BL2_EL3 in normal boot mode.
When flush images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since LOAD_IMAGE_V2 is always enabled in HiKey960 platform. Drop
LOAD_IMAGE v1 to simplify code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
MAP_TSP_MEM could be either in SRAM or DRAM. When MAP_TSP_MEM is in
DRAM, it's overlapped with MAP_DDR.
Since TSP_MEM is always configured in DRAM case, it means
MAP_OPTEE_PAGEABLE is always disabled. Just remove it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The main difference between HiKey960 v1 hardware and HiKey960 v2
hardware is on UART console.
But the function of detecting boardid dumps message before console
ready. So fix it by removing those messages.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>