Without the additional newlines all the text becomes a single paragraph
and next newlines are ignored.
Change-Id: I783198477f654e3923fcabb21248f2bc62c33e9d
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
For rk3399, the L2ACTLR[14] is 0 by default, as ACE CCI-500 doesn't
support WriteEvict. and you will hit the condition L2ACTLR[3] with 0,
as the Evict transactions should propagate to CCI-500 since it has
snoop filters.
Maybe this erratum applies to all Cortex-A53 cores so far, especially
if RK3399's A53 is a r0p4. we should enable it to avoid data corruption,
Change-Id: Ib86933f1fc84f8919c8e43dac41af60fd0c3ce2f
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
A recent commit 030567e6f5 added U()/ULL()
macro to TF constants. This has caused some signed-unsigned comparison
warnings / errors in the TF static analysis.
This patch addresses these issues by migrating impacted variables from
signed ints to unsigned ints and vice verse where applicable.
Change-Id: I4b4c739a3fa64aaf13b69ad1702c66ec79247e53
Signed-off-by: David Cunado <david.cunado@arm.com>
On Juno AArch32, the L2 cache may contain garbage after the warm reset
from AArch64 to AArch32. This is all fine until the MMU is configured
and the data caches enabled. To avoid fetching stale data from the L2
unified cache, invalidate it before the warm reset to AArch32 state.
Change-Id: I7d27e810692c02c3e83c9f31de67f6bae59a960a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Before BL2 loads the SCP ram firmware, `SCP_BOOT_CFG_ADDR` specifies
the primary core. After the SCP ram firmware has started executing,
`SCP_BOOT_CFG_ADDR` is modified. This is not normally an issue but
the Juno AArch32 boot flow is a special case. BL1 does a warm reset
into AArch32 and the core jumps to the `sp_min` entrypoint. This is
effectively a `RESET_TO_SP_MIN` configuration. `sp_min` has to be
able to determine the primary core and hence we need to restore
`SCP_BOOT_CFG_ADDR` to the cold boot value before `sp_min` runs.
This magically worked when booting on A53 because the core index was
zero and it just so happened to match with the new value in
`SCP_BOOT_CFG_ADDR`.
Change-Id: I105425c680cf6238948625c1d1017b01d3517c01
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
For some reason, HDCP key decrytion can't open source in ATF, so we
build it as hdcp.bin. Besides declare the handler for decrypting.
Change-Id: Ia67ff2442ab43cb3ee4875b3d59cc1608e854b4b
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Use TF_CFLAGS instead of CFLAGS, to allow CFLAGS to be overriden from
the make command line.
Change-Id: I3e5726c04bcd0176f232581b8be2c94413374ac7
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
This change avoids warning about type conversion.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Use NULL instead of 0 where required.
Include headers to have the prototype of the functions.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
This change avoids warnings when setting -Wmissing-prototypes or when
using sparse tool.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Call svc_suspend_finish if registered.
psci_get_stat() is static to psci_stat.c
Fix types used in comparison.
Fix coding style (empty line between variable definition and instructions
block).
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
These errata are only applicable to AArch64 state. See the errata notice
for more details:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.epm048406/index.html
Introduce the build options ERRATA_A53_835769 and ERRATA_A53_843419.
Enable both of them for Juno.
Apply the 835769 workaround as following:
* Compile with -mfix-cortex-a53-835769
* Link with --fix-cortex-a53-835769
Apply the 843419 workaround as following:
* Link with --fix-cortex-a53-843419
The erratum 843419 workaround can lead the linker to create new sections
suffixed with "*.stub*" and 4KB aligned. The erratum 835769 can lead the
linker to create new "*.stub" sections with no particular alignment.
Also add support for LDFLAGS_aarch32 and LDFLAGS_aarch64 in Makefile for
architecture-specific linker options.
Change-Id: Iab3337e338b7a0a16b0d102404d9db98c154f8f8
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
TLBI instructions for monitor mode won't have the desired effect under
specific circumstances in Cortex-A57 r0p0. The workaround is to
execute DSB and TLBI twice each time.
Even though this errata is only needed in r0p0, the current errata
framework is not prepared to apply run-time workarounds. The current one
is always applied if compiled in, regardless of the CPU or its revision.
The `DSB` instruction used when initializing the translation tables has
been changed to `DSB ISH` as an optimization and to be consistent with
the barriers used for the workaround.
NOTE: This workaround is present in AArch64 TF and already enabled by
default on Juno.
Change-Id: I10b0baa304ed64b13b7b26ea766e61461e759dfa
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
SPE is only supported in non-secure state. Accesses to SPE specific
registers from SEL1 will trap to EL3. During a world switch, before
`TTBR` is modified the SPE profiling buffers are drained. This is to
avoid a potential invalid memory access in SEL1.
SPE is architecturally specified only for AArch64.
Change-Id: I04a96427d9f9d586c331913d815fdc726855f6b0
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
This patch updates the el3_arch_init_common macro so that it fully
initialises essential control registers rather then relying on hardware
to set the reset values.
The context management functions are also updated to fully initialise
the appropriate control registers when initialising the non-secure and
secure context structures and when preparing to leave EL3 for a lower
EL.
This gives better alignement with the ARM ARM which states that software
must initialise RES0 and RES1 fields with 0 / 1.
This patch also corrects the following typos:
"NASCR definitions" -> "NSACR definitions"
Change-Id: Ia8940b8351dc27bc09e2138b011e249655041cfc
Signed-off-by: David Cunado <david.cunado@arm.com>
This patch enables cache helper functions `flush_dcache_range`,
`clean_dcache_range` and `invalidate_dcache_range` to exit early
if the size argument specified is zero
Change-Id: I0b63e8f4bd3d47ec08bf2a0b0b9a7ff8a269a9b0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch fixes the following issues in Firmware Update (FWU) code:
1. The FWU layer maintains a list of loaded image ids and
while checking for image overlaps, INVALID_IMAGE_IDs were not
skipped. The patch now adds code to skip INVALID_IMAGE_IDs.
2. While resetting the state corresponding to an image, the code
now resets the memory used by the image only if the image were
copied previously via IMAGE_COPY smc. This prevents the invalid
zeroing of image memory which are not copied but are directly
authenticated via IMAGE_AUTH smc.
Change-Id: Idf18e69bcba7259411c88807bd0347d59d9afb8f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Currently, ROTPK_NOT_DEPLOYED flag is set in plat_get_rotpk_info().
It is up to users how to retrieve ROTPK if the ROT verification is
desired. This is not nice.
This commit improves plat_get_rotpk_info() implementation and automates
the ROTPK deployment. UniPhier platform has no ROTPK storage, so it
should be embedded in BL1/BL2, like ARM_ROTPK_LOCATION=devel_rsa case.
This makes sense because UniPhier platform implements its internal ROM
i.e. BL1 is used as updatable pseudo ROM.
Things work like this:
- ROT_KEY (default: $(BUILD_PLAT)/rot_key.pem) is created if missing.
Users can override ROT_KEY from the command line if they want to
use a specific ROT key.
- ROTPK_HASH is generated based on ROT_KEY.
- ROTPK_HASH is included by uniphier_rotpk.S and compiled into BL1/BL2.
- ROT_KEY is input to cert_create tool.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This brings the implementation on par with the software
errata workarounds for AArch64.
Change-Id: I98a85fd92e32ae4259f4ec5b3e93cffc87090064
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This brings the implementation on par with the software
errata workarounds for AArch64.
Change-Id: Id103602e35b1c0ad3705a5b2b7cdb34dd8a8c5e2
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Helper function to assist with errata workaround application.
Change-Id: Idba42ca238442cc826f43444dbfa754e433a5e5e
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Flush the console so the errata report is printed correctly
before exit to normal world.
Change-Id: Idd6b5199b5fb8bda9d16a7b5c6426cdda7c73167
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
On ARM platforms before exiting from SP_MIN ensure that
the default console is switched to the runtime serial port.
Change-Id: I0ca0d42cc47e345d56179eac16aa3d6712767c9b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch changes input param level in xlat_tables_print_internal() to
an unsigned int to fix the signed/unsigned comparison warnings. The
compiler complains about these warnings, thus halting the build flow
for Tegra platforms.
Change-Id: Ieccc262a63daca7a26ca6a14d81466397af8b89f
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: David Cunado <david.cunado@arm.com>
With GCC 6.2 compiler, more C undefined behaviour is being flagged as
warnings, which result in build errors in ARM TF build.
This patch addresses issue caused by enums with values that exceed
maximum value for an int. For these cases the enum is converted to
a set of defines.
Change-Id: I5114164be10d86d5beef3ea1ed9be5863855144d
Signed-off-by: David Cunado <david.cunado@arm.com>
The patch fb7d32e588 migrated the CPU
libraries to have unique defines, prefixing them with the CPU name.
This patch migrates the hikey960 platform port to use the A53 specific
defines.
Change-Id: Id76f544b0b236bbd4974ab5ffa1203f073c20021
Signed-off-by: David Cunado <david.cunado@arm.com>
In CPU off callback function, the old code uses the function
hisi_test_pwrdn_allcores() to check if all CPUs in cluster have been
powered off and if it's valid then power off the whole cluster. But the
function hisi_test_pwrdn_allcores() only maintains the different power
states only for CPU suspend/resume flow, so it cannot return correct
states for CPU on/off flow.
This patch is to change use hisi_test_cpu_down() to check if all CPUs
have been powered off, so that can power off the whole cluster properly
when all CPUs in cluster have been hotplugged off.
Signed-off-by: Tao Wang <kevin.wangtao@hisilicon.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>