Define default DDR location to which ATF has to compiled
if DEBUG option is enabled. This is required now, as the ATF cant fit
in OCM with DEBUG option enabled. The default value is 0x1000 and can be
used till 0x7ffff. User can still override as per wish/requirement
using current commandline options.
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add pin control APIs which driver can use to query
pin information from firmware. Using these APIs,
driver do not need to maintain hard-coded pin database.
Major changes in patch are:
- Add pin database with pins, functions and function groups
information
- Implement APIs for pin information queries
- Update pin control APIs for get/set functions to use new
pin control database. Remove pin database which was added
earlier.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add IOCTLs to read/write global general storage and
persistent global general storage registers access.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
- Add clock entries and information to clock database.
- Implement APIs to provide clock topology and other
information to caller.
- Implement APIs to control clocks and PLLs.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
These are empty functions with no logic right now. Code
will be added in subsequent commits.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement ioctl APIs which uses MMIO operations
to configure devices. Below IOCTLs are supported
in this patch:
* Set tap delay bypass
* Set SGMII mode
* SD reset
* Set SD/MMC tap delay
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement ioctl APIs which uses MMIO operations
to control RPU operations. Below IOCTLs are supported
in this patch:
* Get RPU operation mode
* Set RPU operation mode
* Configure RPU boot address (OCM/TCM)
* Configure TCM combined mode
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement pin control APIs which uses MMIO operations
to set/get values of configuration parameters.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement pin control APIs which uses MMIO operations
to set/get functions for the given pin.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add wrappers for pin control APIs. Actual implementation of
these APIs would be done in subsequent changes.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add new function and node IDs supported by PMUFW in
function list and node list respectively.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
The FVP platform port for SP_MIN (BL32) didn't map the flash memory
in BL32 for stroring the mem_protect enable state information leading
to synchronous exception. The patch fixes it by adding the region to
the BL32 mmap tables.
Change-Id: I37eec83c3e1ea43d1b5504d3683eebc32a57eadf
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>
Boot memory layout is specific for a platform, but should not be
mixed up with other platform specific attributes. A separate file is
much cleaner and better to compare with other platforms. Take a look
at plat/poplar where it is done the same way.
Moved hikey_def.h to system include folder and moved includes from
hikey_def.h to more general platform_def.h.
Signed-off-by: Michael Brandl <git@fineon.pw>
Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.
In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.
Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.
Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This issue was detected when testing FWU on Juno. The Timer
`timer_ops` was not being initialized before being used by
the SDS driver on Juno. This patch adds the call to
`generic_delay_timer_init()` during bl2u_early_platform_setup().
This is done generically for all ARM platforms because the
cost involved is minimal.
Change-Id: I349cf0bd1db68406eb2298b65f9c729f792cabdc
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
plat/hisilicon/hikey/hikey_bl1_setup.c:565:47:
error: value size does not match register size specified by the
constraint and modifier [-Werror,-Wasm-operand-widths]
__asm__ volatile ("mrs %0, cpacr_el1" : "=r"(data));
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
It's unnecessary to call platform driver initialization in image
load driver. We could make bl2_platform_setup() to executing
just before SCP_BL2 by setting flag IMAGE_ATTRIB_PLAT_SETUP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since non-TF ROM is used in HiKey960 platform (Hisilicon Hi3660 SoC),
replace BL1 by BL2_EL3 in normal boot mode.
When flush images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since LOAD_IMAGE_V2 is always enabled in HiKey960 platform. Drop
LOAD_IMAGE v1 to simplify code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
MAP_TSP_MEM could be either in SRAM or DRAM. When MAP_TSP_MEM is in
DRAM, it's overlapped with MAP_DDR.
Since TSP_MEM is always configured in DRAM case, it means
MAP_OPTEE_PAGEABLE is always disabled. Just remove it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The main difference between HiKey960 v1 hardware and HiKey960 v2
hardware is on UART console.
But the function of detecting boardid dumps message before console
ready. So fix it by removing those messages.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since non-TF ROM is used in HiKey platform (Hisilicon Hi6220 SoC),
replace BL1 by BL2_EL3 in normal boot mode.
When we recovery images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Although SRAM is initialized, DCACHE should be cleaned too.
Because MCU is a parrallel core to access SRAM. We need to make
sure that initialized value is really written to SRAM before
MCU using it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since LOAD_IMAGE_V2 is always enabled in HiKey platform. Drop
LOAD_IMAGE v1 to simplify code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The register address range of UART1 (crash console) are outside the
address ranges mapped for MMIO, resulting to an MMU abort when the
device registers are accessed.
Increase the size of DEVICE1 memory to include the range of UART1.
FixesARM-software/tf-issues#560
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.
The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.
FixesARM-software/tf-issues#559
Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This was correct according to the model specifications , but it seems
that FVP doesn't implement it. It is safer to use the size exposed by
the DTB which is currently used by Linux.
Change-Id: I9aabe3284a50ec2a36ed94966eb7e4ddf37cec3b
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Some generic compatibility functions emit deprecated declaration warnings
even when platforms do not use the deprecated functions directly. This
can be confusing. Suppress these warnings by using:
`#pragma GCC diagnostic ignored "-Wdeprecated-declarations"`
Also emit a runtime warning if the weak plat/common implemntation of
plat_get_syscnt_freq2() is used, as this implies the platform has not
migrated from plat_get_syscnt_freq(). The deprecated declaration warnings
only help detect when platforms are calling deprecated functions, not when
they are defining deprecated functions.
FixesARM-software/tf-issues#550
Change-Id: Id14a92279c2634c1e76db8ef210da8affdbb2a5d
Signed-off-by: Dan Handley <dan.handley@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=juno LOG_LEVEL=50 all
Change-Id: Ic8f611da734f356566e8208053296e6c62b54709
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.3: All declarations of an object or function shall
use the same names and type qualifiers.
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I48201c9ef022f6bd42ea8644529afce70f9b3f22
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined.
Change-Id: I26e042cb251a6f9590afa1340fdac73e42f23979
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
FVPs that model DynamIQ configuration implements all CPUs in a single
cluster. I.e., such models have a single cluster with more than 4 CPUs.
This differs from existing default build configuration for FVP where up
to 4 CPUs are assumed per cluster.
To allow building for DynamIQ configuration, promote the macro
FVP_MAX_CPUS_PER_CLUSTER as a build option to have it set from the build
command line. The value of the build option defaults to 4.
Change-Id: Idc3853bc95f680869b434b011c2dbd733e40c6ce
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Update qemu_configure_mmu_##_el to add an additional region for code,
marked as MT_CODE | MT_SECURE. Update ro region attributes to NON_EXEC.
Update calls to QEMU_CONFIGURE_BLx_MMU() to pass an additional region for
code. Update calls to pass regions defined in common_def.h.
Increase MAX_MMAP_REGIONS to 10.
Enable SEPARATE_CODE_AND_RODATA by default on QEMU builds.
FixesARM-software/tf-issues#558
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
The SCP binaries provided in the 17.10 Linaro release (and onwards)
have migrated to the SCMI/SDS protocols. Therefore, the ARM TF should
now use the corresponding drivers by default.
This patch changes the default value of the CSS_USE_SCMI_SDS_DRIVER
build option to 1 for Juno.
Change-Id: Idb7e3c6af582f49e332167a2158703c2d781b437
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
MISRA C-2012 Rule 7.3 violation: lowercase l shall not be used as literal suffixes.
This patch resolves this for the ULL() macro by using ULL suffix instead
of the ull suffix.
Change-Id: Ia8183c399e74677e676956e8653e82375d0e0a01
Signed-off-by: David Cunado <david.cunado@arm.com>
This patch restricts building the dynamic config DTBs to the Unix
build environment as the Device Tree compiler may not be available
on other build environments.
Change-Id: Ie690e80010a174300e966240fd977b37561156e0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch also fixes the assumption that the counters are disabled on
the resume path. This is incorrect as the AMU counters are enabled
early in the CPU reset function before `cpuamu_context_restore()`
runs.
Change-Id: I38a94eb166a523f00de18e86860434ffccff2131
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch also fixes `cpuamu_write_cpuamcntenclr_el0()` to use an MSR
instruction instead of an MRS instruction.
Change-Id: Ia6531f64b5ebc60ba432124eaa8d8eaccba40ed0
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
When the MMU is enabled and the translation tables are mapped, data
read/writes to the translation tables are made using the attributes
specified in the translation tables themselves. However, the MMU
performs table walks with the attributes specified in TCR_ELx. They are
completely independent, so special care has to be taken to make sure
that they are the same.
This has to be done manually because it is not practical to have a test
in the code. Such a test would need to know the virtual memory region
that contains the translation tables and check that for all of the
tables the attributes match the ones in TCR_ELx. As the tables may not
even be mapped at all, this isn't a test that can be made generic.
The flags used by enable_mmu_xxx() have been moved to the same header
where the functions are.
Also, some comments in the linker scripts related to the translation
tables have been fixed.
Change-Id: I1754768bffdae75f53561b1c4a5baf043b45a304
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch adds TB_FW_CONFIG for FVP and allows FVP
to select the appropriate HW_CONFIG to include in the
fip. The HW_CONFIG for FVP is selected via `FVP_HW_CONFIG_DTS`
build option. The TB_FW_CONFIG specifies the load address of
HW_CONFIG to BL2. Since currently the load address is different
between AARCH32 and AARCH64, 2 separate TB_FW_CONFIGs are
maintained for the 2 modes.
Change-Id: Ide8581e752dfa900087f5895c775073c841c0daf
Signed-Off-By: Soby Mathew <soby.mathew@arm.com>
The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :
1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.
2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.
3. The `libfdt` sources are now included when BL2 is built
4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.
5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.
6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.
Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.
Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The `bl1_init_bl2_mem_layout()` API is now deprecated. The default weak
implementation of `bl1_plat_handle_post_image_load()` calculates the
BL2 memory layout and populates the same in x1(r1). This ensures
compatibility for the deprecated API.
Change-Id: Id44bdc1f572dc42ee6ceef4036b3a46803689315
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.
Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch introduces a new BL handover interface. It essentially allows
passing 4 arguments between the different BL stages. Effort has been made
so as to be compatible with the previous handover interface. The previous
blx_early_platform_setup() platform API is now deprecated and the new
blx_early_platform_setup2() variant is introduced. The weak compatiblity
implementation for the new API is done in the `plat_bl_common.c` file.
Some of the new arguments in the new API will be reserved for generic
code use when dynamic configuration support is implemented. Otherwise
the other registers are available for platform use.
Change-Id: Ifddfe2ea8e32497fe1beb565cac155ad9d50d404
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds an argument to bl1_plat_post/pre_image_load() APIs
to make it more future proof. The default implementation of
these are moved to `plat_bl1_common.c` file.
These APIs are now invoked appropriately in the FWU code path prior
to or post image loading by BL1 and are not restricted
to LOAD_IMAGE_V2.
The patch also reorganizes some common platform files. The previous
`plat_bl2_el3_common.c` and `platform_helpers_default.c` files are
merged into a new `plat_bl_common.c` file.
NOTE: The addition of an argument to the above mentioned platform APIs
is not expected to have a great impact because these APIs were only
recently added and are unlikely to be used.
Change-Id: I0519caaee0f774dd33638ff63a2e597ea178c453
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
After executing a TLBI a DSB is needed to ensure completion of the
TLBI.
rk3328: The MMU is allowed to load TLB entries for as long as it is
enabled. Because of this, the correct place to execute a TLBI is right
after disabling the MMU.
Change-Id: I8280f248d10b49a8c354a4ccbdc8f8345ac4c170
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Commit fdb1964c34 ("xlat: Introduce
MAP_REGION2() macro") added a granularity field to mmap_region_t.
Tegra platforms were using the v2 xlat_tables implementation in
common/tegra_common.mk, but v1 xlat_tables.h headers in soc/*/plat_setup.c
where arrays are being defined. This caused the next physical address to
be read as granularity, causing EINVAL error and triggering an assert.
Consistently use xlat_tables_v2.h header to avoid this.
FixesARM-software/tf-issues#548.
Signed-off-by: Andreas Färber <afaerber@suse.de>
The console core flush API expects the base address in the first
register, but ARM helpers currently sets the second register with the
base address. This causes an assert failure.
This patch fixes that.
Change-Id: Ic54c423cd60f2756902ab3cfc77b3de2ac45481e
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Function plat_ic_get_pending_interrupt_type() should return interrupt
type, not id. The function is used in aarch64 exception handling and
currently the irq/fiq forwarding fails if a secure interrupt happens while
running normal world.
The qemu-specific gic file does not contain any extra functionality so it
can be removed and common file can be used instead.
fixesarm-software/tf-issues#546
Signed-off-by: Santeri Salko <santeri.salko@gmail.com>
Define Qemu AArch32 implementation for some platform functions
(core position, secondary boot cores, crash console). These are
derived from the AArch64 implementation.
BL31 on Qemu is needed only for ARMv8 and later. On ARMv7, BL32 is
the first executable image after BL2.
Support SP_MIN and OP-TEE as BL32: create a sp_min make script target
in Qemu, define mapping for IMAGE_BL32
Minor fix Qemu return value type for plat_get_ns_image_entrypoint().
Qemu model for the Cortex-A15 does not support the virtualization
extension although the core expects it. To overcome the issue, Qemu
ARMv7 configuration set ARCH_SUPPORTS_VIRTUALIZATION to 0.
Add missing AArch32 assembly macro arm_print_gic_regs from ARM platform
used by the Qemu platform.
Qemu Cortex-A15 model integrates a single cluster with up to 4 cores.
Change-Id: I65b44399071d6f5aa40d5183be11422b9ee9ca15
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Looks like this is requirement in the pre-merge static analysis.
misra_violation: [Required] MISRA C-2012 Rule 7.2 violation:
Unsigned constants must be declared with U or u suffix.
Adding ULL as requested. I used ULL() macros for BL*_{BASE,LIMIT}
because they are referenced from linker scripts.
Requested-by: David Cunado <david.cunado@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the xlat region of the on-chip SRAM is always allocated
for all BL images.
The access to the on-chip SRAM is necessary for loading images from
a USB memory device (i.e. when updating firmware), so unneeded for
the usual boot procedure.
To avoid this waste, allocate the xlat region dynamically only for
BL2, and only when it is necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 247fc04351 ("uniphier: switch to BL2-AT-EL3 and remove BL1
support") accidentally changed the location of BL31 and BL32. The
new memory map overlaps with the audio DSP images, also gives impact
to OP-TEE. They are both out of control of ARM Trusted Firmware, so
not easy to change. This commit restores the image layout that was
originally used prior to the BL2-AT-EL3 migration.
Reported-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Allow to handle GZIP-compressed images by giving FIP_GZIP=1 from the
command line.
- Images are GZIP-compressed, then packed into FIP. If Trusted Board
Boot is enabled, certificates are generated based on the compressed
images.
- GZIP decompressor is linked into BL2 to decompress images at
run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the next commit, I will have more usecases to get struct image_info
from image ID. It is better to make a helper function at a different
layer. I do not need the current uniphier_image_descs_fixup() since
the code is small enough to be squashed into the caller side.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Just like bl2_, add pre/post image load handlers for BL1. No argument
is needed since BL2 is the only image loaded by BL1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are cases where we need to manipulate image information before
the load. For example, for decompressing data, we cannot load the
compressed images to their final destination. Instead, we need to
load them to the temporary buffer for the decompressor.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When we add a new callback, we need to duplicate fallbacks among
plat/common/{aarch32,aarch64}/platform_helpers.S This is tedious.
I created a new C file, then moved 3 functions:
plat_error_handler
bl2_plat_preload_setup
plat_try_next_boot_source
They are called from C, so I do not see a good reason to implement
them in assembly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the next commit, I need the image name in lowercase because
output files are generally named in lowercase.
Unfortunately, TOOL_ADD_IMG takes the first argument in uppercase
since we generally use uppercase Make variables.
make_helpers/build_macros.mk provides 'uppercase' macro to convert
a string into uppercase, but 'lowercase' does not exist. We can
implement it if we like, but it would be more straightforward to
change the argument of TOOL_ADD_IMG.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now FIP_ADD_IMG takes care of both fiptool and cert_create
symmetrically. Rename it so that it matches the behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Rajan Vaja
Jolly Shah
Joel Hutton
Michael Brandl
davidcunado-arm
Antonio Nino Diaz
Soby Mathew
Haojian Zhuang
Michalis Pappas
Roberto Vargas
Dan Handley
Jeenu Viswambharan
Sandrine Bailleux
Dimitris Papastamos
Arve Hjønnevåg
Andreas Färber
Santeri Salko
Victor Chong
Etienne Carriere
Masahiro Yamada