On Juno, the secure privileged invasive debug authentication signal
(SPIDEN) is controlled by board SCC registers, which by default enable
SPIDEN. Disable secure privileged external debug in release builds by
programming the appropriate Juno SoC registers.
Change-Id: I61045f09a47dc647bbe95e1b7a60e768f5499f49
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Trusted Firmware currently has no support for secure self-hosted
debug. To avoid unexpected exceptions, disable software debug
exceptions, other than software breakpoint instruction exceptions,
from all exception levels in secure state. This applies to both
AArch32 and AArch64 EL3 initialization.
Change-Id: Id097e54a6bbcd0ca6a2be930df5d860d8d09e777
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
This patch introduces the following three platform interfaces:
* void plat_psci_stat_accounting_start(const psci_power_state_t *state_info)
This is an optional hook that platforms can implement in order
to perform accounting before entering a low power state. This
typically involves capturing a timestamp.
* void plat_psci_stat_accounting_stop(const psci_power_state_t *state_info)
This is an optional hook that platforms can implement in order
to perform accounting after exiting from a low power state. This
typically involves capturing a timestamp.
* u_register_t plat_psci_stat_get_residency(unsigned int lvl,
const psci_power_state_t *state_info,
unsigned int last_cpu_index)
This is an optional hook that platforms can implement in order
to calculate the PSCI stat residency.
If any of these interfaces are overridden by the platform, it is
recommended that all of them are.
By default `ENABLE_PSCI_STAT` is disabled. If `ENABLE_PSCI_STAT`
is set but `ENABLE_PMF` is not set then an alternative PSCI stat
collection backend must be provided. If both are set, then default
weak definitions of these functions are provided, using PMF to
calculate the residency.
NOTE: Previously, platforms did not have to explicitly set
`ENABLE_PMF` since this was automatically done by the top-level
Makefile.
Change-Id: I17b47804dea68c77bc284df15ee1ccd66bc4b79b
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Introduce zeromem_dczva function on AArch64 that can handle unaligned
addresses and make use of DC ZVA instruction to zero a whole block at a
time. This zeroing takes place directly in the cache to speed it up
without doing external memory access.
Remove the zeromem16 function on AArch64 and replace it with an alias to
zeromem. This zeromem16 function is now deprecated.
Remove the 16-bytes alignment constraint on __BSS_START__ in
firmware-design.md as it is now not mandatory anymore (it used to comply
with zeromem16 requirements).
Change the 16-bytes alignment constraints in SP min's linker script to a
8-bytes alignment constraint as the AArch32 zeromem implementation is now
more efficient on 8-bytes aligned addresses.
Introduce zero_normalmem and zeromem helpers in platform agnostic header
that are implemented this way:
* AArch32:
* zero_normalmem: zero using usual data access
* zeromem: alias for zero_normalmem
* AArch64:
* zero_normalmem: zero normal memory using DC ZVA instruction
(needs MMU enabled)
* zeromem: zero using usual data access
Usage guidelines: in most cases, zero_normalmem should be preferred.
There are 2 scenarios where zeromem (or memset) must be used instead:
* Code that must run with MMU disabled (which means all memory is
considered device memory for data accesses).
* Code that fills device memory with null bytes.
Optionally, the following rule can be applied if performance is
important:
* Code zeroing small areas (few bytes) that are not secrets should use
memset to take advantage of compiler optimizations.
Note: Code zeroing security-related critical information should use
zero_normalmem/zeromem instead of memset to avoid removal by
compilers' optimizations in some cases or misbehaving versions of GCC.
FixesARM-software/tf-issues#408
Change-Id: Iafd9663fc1070413c3e1904e54091cf60effaa82
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
`PMF_ARM_TIF_IMPL_ID` should be set to 0x41. The code already left
shifts it by 24 bit positions so this was overflowing.
This fixes a build error with GCC 6.2 when
`ENABLE_RUNTIME_INSTRUMENTATION` is set.
Change-Id: I4c99d48ea7ce3d76e9edd1325b1979994db2c0fb
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
The errata reporting policy is as follows:
- If an errata workaround is enabled:
- If it applies (i.e. the CPU is affected by the errata), an INFO
message is printed, confirming that the errata workaround has been
applied.
- If it does not apply, a VERBOSE message is printed, confirming
that the errata workaround has been skipped.
- If an errata workaround is not enabled, but would have applied had
it been, a WARN message is printed, alerting that errata workaround
is missing.
The CPU errata messages are printed by both BL1 (primary CPU only) and
runtime firmware on debug builds, once for each CPU/errata combination.
Relevant output from Juno r1 console when ARM Trusted Firmware is built
with PLAT=juno LOG_LEVEL=50 DEBUG=1:
VERBOSE: BL1: cortex_a57: errata workaround for 806969 was not applied
VERBOSE: BL1: cortex_a57: errata workaround for 813420 was not applied
INFO: BL1: cortex_a57: errata workaround for disable_ldnp_overread was applied
WARNING: BL1: cortex_a57: errata workaround for 826974 was missing!
WARNING: BL1: cortex_a57: errata workaround for 826977 was missing!
WARNING: BL1: cortex_a57: errata workaround for 828024 was missing!
WARNING: BL1: cortex_a57: errata workaround for 829520 was missing!
WARNING: BL1: cortex_a57: errata workaround for 833471 was missing!
...
VERBOSE: BL31: cortex_a57: errata workaround for 806969 was not applied
VERBOSE: BL31: cortex_a57: errata workaround for 813420 was not applied
INFO: BL31: cortex_a57: errata workaround for disable_ldnp_overread was applied
WARNING: BL31: cortex_a57: errata workaround for 826974 was missing!
WARNING: BL31: cortex_a57: errata workaround for 826977 was missing!
WARNING: BL31: cortex_a57: errata workaround for 828024 was missing!
WARNING: BL31: cortex_a57: errata workaround for 829520 was missing!
WARNING: BL31: cortex_a57: errata workaround for 833471 was missing!
...
VERBOSE: BL31: cortex_a53: errata workaround for 826319 was not applied
INFO: BL31: cortex_a53: errata workaround for disable_non_temporal_hint was applied
Also update documentation.
Change-Id: Iccf059d3348adb876ca121cdf5207bdbbacf2aba
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
At present, spin locks can only defined from C files. Add some macros
such that they can be defined from assembly files too.
Change-Id: I64f0c214062f5c15b3c8b412c7f25c908e87d970
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
With GCC 6.2 compiler, more C undefined behaviour is being flagged as
warnings, which result in build errors in ARM TF build.
The specific issue that this patch resolves is the use of (1 << 31),
which is predominantly used in case statements, where 1 is represented
as a signed int. When shifted to msb the behaviour is undefined.
The resolution is to specify 1 as an unsigned int using a convenience
macro ULL(). A duplicate macro MAKE_ULL() is replaced.
FixesARM-software/tf-issues#438
Change-Id: I08e3053bbcf4c022ee2be33a75bd0056da4073e1
Signed-off-by: David Cunado <david.cunado@arm.com>
Some side-channel attacks involve an attacker inferring something from
the time taken for a memory compare operation to complete, for example
when comparing hashes during image authentication. To mitigate this,
timingsafe_bcmp() must be used for such operations instead of the
standard memcmp().
This function executes in constant time and so doesn't leak any timing
information to the caller.
Change-Id: I470a723dc3626a0ee6d5e3f7fd48d0a57b8aa5fd
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This code has been imported and slightly adapted from FreeBSD:
6253393ad8/lib/libc/string/strnlen.c
Change-Id: Ie5ef5f92e6e904adb88f8628077fdf1d27470eb3
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
One nasty part of ATF is some of boolean macros are always defined
as 1 or 0, and the rest of them are only defined under certain
conditions.
For the former group, "#if FOO" or "#if !FOO" must be used because
"#ifdef FOO" is always true. (Options passed by $(call add_define,)
are the cases.)
For the latter, "#ifdef FOO" or "#ifndef FOO" should be used because
checking the value of an undefined macro is strange.
Here, IMAGE_BL* is handled by make_helpers/build_macro.mk like
follows:
$(eval IMAGE := IMAGE_BL$(call uppercase,$(3)))
$(OBJ): $(2)
@echo " CC $$<"
$$(Q)$$(CC) $$(TF_CFLAGS) $$(CFLAGS) -D$(IMAGE) -c $$< -o $$@
This means, IMAGE_BL* is defined when building the corresponding
image, but *undefined* for the other images.
So, IMAGE_BL* belongs to the latter group where we should use #ifdef
or #ifndef.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix the parameter type of the maintenance functions of data cache.
Add missing declarations for AArch32 versions of dcsw_op_louis and
dcsw_op_all to match the AAch64 ones.
Change-Id: I4226e8ea4f8b2b5bc2972992c83de659ee0da52c
We have lots of duplicated defines (and comment blocks too).
Move them to include/plat/common/common_def.h.
While we are here, suffix the end address with _END instead of
_LIMIT. The _END is a better fit to indicate the linker-derived
real end address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The usage of _LIMIT seems odd here, so rename as follows:
BL_CODE_LIMIT --> BL_CODE_END
BL_RO_DATA_LIMIT --> BL_RO_DATA_END
BL1_CODE_LIMIT --> BL1_CODE_END
BL1_RO_DATA_LIMIT --> BL1_RO_DATA_END
Basically, we want to use _LIMIT and _END properly as follows:
*_SIZE + *_MAX_SIZE = *_LIMIT
*_SIZE + *_SIZE = *_END
The _LIMIT is generally defined by platform_def.h to indicate the
platform-dependent memory constraint. So, its typical usage is
ASSERT(. <= BL31_LIMIT, "BL31 image has exceeded its limit.")
in a linker script.
On the other hand, _END is used to indicate the end address of the
compiled image, i.e. we do not know it until the image is linked.
Here, all of these macros belong to the latter, so should be
suffixed with _END.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Delete old version of libfdt at lib/libfdt. Move new libfdt API
headers to include/lib/libfdt and all other files to lib/libfdt.
Change-Id: I32b7888f1f20d62205310e363accbef169ad7b1b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
We are duplicating this macro define, and it is useful enough
to be placed in the common place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
tbz check for RDR status is to check for a bit being zero.
Unfortunately, we are using a mask rather than the bit position.
Further as per http://www.ti.com/lit/ds/symlink/pc16550d.pdf (page 17),
LSR register bit 0 is Data ready status (RDR), not bit position 2.
Update the same to match the specification.
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Previously, fiptool only understood a fixed set of images as
specified in tbbr_config.c. It preserved unknown images during
the update, unpack and remove operations but it was not possible to
explicitly refer to one of those unknown images.
Add a new --blob option to create/update/unpack/remove images that
are not known at compile time. This is accomplished by specifying
the UUID and filename pair as shown below:
$ ./fiptool create --blob uuid=01234567-89ab-cdef-0123-456789abcdef,file=foo.bin fip.bin
$ ./fiptool info fip.bin
01234567-89ab-cdef-0123-456789abcdef: offset=0x60, size=0x1AA68
FixesARM-software/tf-issues#420
Change-Id: Iaac2504b9a4252289c09e73d29645cbe240f3a82
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Standard SMC requests that are handled in the secure-world by the Secure
Payload can be preempted by interrupts that must be handled in the
normal world. When the TSP is preempted the secure context is stored and
control is passed to the normal world to handle the non-secure
interrupt. Once completed the preempted secure context is restored. When
restoring the preempted context, the dispatcher assumes that the TSP
preempted context is still stored as the SECURE context by the context
management library.
However, PSCI power management operations causes synchronous entry into
TSP. This overwrites the preempted SECURE context in the context
management library. When restoring back the SECURE context, the Secure
Payload crashes because this context is not the preempted context
anymore.
This patch avoids corruption of the preempted SECURE context by aborting
any preempted SMC during PSCI power management calls. The
abort_std_smc_entry hook of the TSP is called when aborting the SMC
request.
It also exposes this feature as a FAST SMC callable from normal world to
abort preempted SMC with FID TSP_FID_ABORT.
Change-Id: I7a70347e9293f47d87b5de20484b4ffefb56b770
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
Enforce valid FID input in TSP_STD_FID and TSP_FAST_FID macros.
Also remove an undefined behavior by using unsigned literals.
Change-Id: Id37e908da861980a4eaa3a70b37a729f416ce272
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
The is_mem_free() function used to be local to bl_common.c.
This patch exports it so that it can be used outside of bl_common.c.
Change-Id: I01dcb4229f3a36f56a4724b567c5e6c416dc5e98
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
ASM_ASSERT failure and panic messages are suppressed at present. This
patch enables printing the PC location for panic messages, and file name
and line number upon assembly assert failure.
Change-Id: I80cb715988e7ce766f64da1e1d7065a74a096a0c
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Various CPU drivers in ARM Trusted Firmware register functions to handle
power-down operations. At present, separate functions are registered to
power down individual cores and clusters.
This scheme operates on the basis of core and cluster, and doesn't cater
for extending the hierarchy for power-down operations. For example,
future CPUs might support multiple threads which might need powering
down individually.
This patch therefore reworks the CPU operations framework to allow for
registering power down handlers on specific level basis. Henceforth:
- Generic code invokes CPU power down operations by the level
required.
- CPU drivers explicitly mention CPU_NO_RESET_FUNC when the CPU has no
reset function.
- CPU drivers register power down handlers as a list: a mandatory
handler for level 0, and optional handlers for higher levels.
All existing CPU drivers are adapted to the new CPU operations framework
without needing any functional changes within.
Also update firmware design guide.
Change-Id: I1826842d37a9e60a9e85fdcee7b4b8f6bc1ad043
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The previous code required that a certificate be signed with the ROT
key before the platform's NV counter could be updated with the value
in the certificate. This implies that the Non-Trusted NV counter was
not being updated for Non-Trusted content certificates, as they cannot
be signed with the ROT key in the TBBR CoT scheme.
The code is reworked to only allow updating the platform's Trusted NV
counter when a certificate protected by the Trusted NV counter is
signed with the ROT key.
Content certificates protected by the Non-Trusted NV counter are
allowed to update the platform's Non-Trusted NV counter, assuming
that the certificate value is higher than the platform's value.
A new optional platform API has been introduced, named
plat_set_nv_ctr2(). Platforms may choose to implement it and perform
additional checks based on the authentication image descriptor before
modifying the NV counters. A default weak implementation is available
that just calls into plat_set_nv_ctr().
FixesARM-software/tf-issues#426
Change-Id: I4fc978fd28a3007bc0cef972ff1f69ad0413b79c
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
As with other ARM platform GIC APIs, these directly invoke the GICv3
driver APIs for Redistributor power management.
For the sake of uniform GIC API, empty stubs are placed for those GIC
drivers that lack Redistributor component.
Change-Id: Iad0d760d4dbca790998f7768cda621ff3b15a864
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Some GICv3 implementations have provision for power management
operations at Redistributor level. This patch introduces and provides
place-holders for Redistributor power management. The default
implementations are empty stubs, but are weakly bound so as to enable
implementation-specific drivers to override them.
Change-Id: I4fec1358693d3603ca5dce242a2f7f0e730516d8
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch enables TRUSTED_BOARD_BOOT (Authentication and FWU)
support, for AArch64, when LOAD_IMAGE_V2 is enabled.
This patch also enables LOAD_IMAGE_V2 for ARM platforms.
Change-Id: I294a2eebce7a30b6784c80c9d4ac7752808ee3ad
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Some files have incorrect copyright notices, this patch fixes all
files with deviations from the standard notice.
Change-Id: I66b73e78a50a235acb55f1e2ec2052a42c0570d2
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Testing showed that the time spent in a cluster power down
operation is dominated by cache flushes. Add two more timestamps
in runtime instrumentation to keep track of the time spent
flushing the L1/L2 caches.
Change-Id: I4c5a04e7663543225a85d3c6b271d7b706deffc4
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
The now deprecated ADDR_SPACE_SIZE has been replaced by the two
defines PLAT_PHY_ADDR_SPACE_SIZE and PLAT_VIRT_ADDR_SPACE_SIZE.
Change-Id: I027a2f02f47ab2f679b8979a6dbfb0f08270a1a4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Added the definitions `PLAT_PHY_ADDR_SPACE_SIZE` and
`PLAT_VIRT_ADDR_SPACE_SIZE` which specify respectively the physical
and virtual address space size a platform can use.
`ADDR_SPACE_SIZE` is now deprecated. To maintain compatibility, if any
of the previous defines aren't present, the value of `ADDR_SPACE_SIZE`
will be used instead.
For AArch64, register ID_AA64MMFR0_EL1 is checked to calculate the
max PA supported by the hardware and to verify that the previously
mentioned definition is valid. For AArch32, a 40 bit physical
address space is considered.
Added asserts to check for overflows.
Porting guide updated.
Change-Id: Ie8ce1da5967993f0c94dbd4eb9841fc03d5ef8d6
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Each translation table level entry can only map a given virtual
address onto physical addresses of the same granularity. For example,
with the current configuration, a level 2 entry maps blocks of 2 MB,
so the physical address must be aligned to 2 MB. If the address is not
aligned, the MMU will just ignore the lower bits.
This patch adds an assertion to make sure that physical addresses are
always aligned to the correct boundary.
Change-Id: I0ab43df71829d45cdbe323301b3053e08ca99c2c
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The AArch32 Procedure call Standard mandates that the stack must be aligned
to 8 byte boundary at external interfaces. This patch does the required
changes.
This problem was detected when a crash was encountered in
`psci_print_power_domain_map()` while printing 64 bit values. Aligning
the stack to 8 byte boundary resolved the problem.
FixesARM-Software/tf-issues#437
Change-Id: I517bd8203601bb88e9311bd36d477fb7b3efb292
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The capabilities exposed by the PSCI generic layer depends on the hooks
populated by the platform in `plat_arm_psci_pm_ops`. Currently ARM
Standard platforms statically define this structure. However, some
platforms may want to modify the hooks at runtime before registering
them with the generic layer.
This patch introduces a new ARM platform layer API
`plat_arm_psci_override_pm_ops` which allows the platform to probe
the power controller and modify `plat_arm_psci_pm_ops` if required.
Consequently, 'plat_arm_psci_pm_ops' is no longer qualified as
`const` on ARM Standard platforms.
Change-Id: I7dbb44b7bd36c20ec14ded5ee45a96816ca2ab9d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch introduces an additional layer of abstraction between
CSS power management hooks and the SCPI driver. A new set of APIs
are introduced in order to abstract out power management operations
from underlying communication mechanism with the SCP.
The SCPI and the associated MHU drivers are moved into a `drivers`
folder in CSS. The new SCP communication abstraction layer is added
in the `drivers/scp` folder. The existing CSS power management
uses the new APIs to reflect this abstraction.
Change-Id: I7d775129fc0558e9703c2724523fb8f0a916838c
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
There are many instances in ARM Trusted Firmware where control is
transferred to functions from which return isn't expected. Such jumps
are made using 'bl' instruction to provide the callee with the location
from which it was jumped to. Additionally, debuggers infer the caller by
examining where 'lr' register points to. If a 'bl' of the nature
described above falls at the end of an assembly function, 'lr' will be
left pointing to a location outside of the function range. This misleads
the debugger back trace.
This patch defines a 'no_ret' macro to be used when jumping to functions
from which return isn't expected. The macro ensures to use 'bl'
instruction for the jump, and also, for debug builds, places a 'nop'
instruction immediately thereafter (unless instructed otherwise) so as
to leave 'lr' pointing within the function range.
Change-Id: Ib34c69fc09197cfd57bc06e147cc8252910e01b0
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch resets EL2 and EL3 registers that have architecturally
UNKNOWN values on reset and that also provide EL2/EL3 configuration
and trap controls.
Specifically, the EL2 physical timer is disabled to prevent timer
interrups into EL2 - CNTHP_CTL_EL2 and CNTHP_CTL for AArch64 and AArch32,
respectively.
Additionally, for AArch64, HSTR_EL2 is reset to avoid unexpected traps of
non-secure access to certain system registers at EL1 or lower.
For AArch32, the patch also reverts the reset to SDCR which was
incorrectly added in a previous change.
Change-Id: If00eaa23afa7dd36a922265194ccd6223187414f
Signed-off-by: David Cunado <david.cunado@arm.com>
C99 restricts bitfields type is signed and unsigned integer or _Bool.
See section 6.7.2.1 Structure and union specifiers.
"A bit-field shall have a type that is a qualified or unqualified version
of _Bool, signed int, unsigned int, or some other implementation-defined type."
Since the compiler packs bitfields anyways, actual data layout in the structure is unaffected.
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
This patch makes following miscellaneous fixes:
* pl011_console.S: Fixed the bit mask used to check if the
transmit FIFO is full or empty.
* smcc_macros.S: Added `_fsxc` suffix while updating the SPSR.
By default the assembler assumes `_fc` suffix which does not
update all the fields in SPSR. By adding `_fsxc` suffix all
the fields gets updated.
* platform_helpers.S: Removed the weak definition for
`plat_my_core_pos()` as this is a mandatory function which
needs to be defined by all platforms.
Change-Id: I8302292533c943686fff8d7c749a07132c052a3b
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
This allows the debugger to print the callstack when there is an
assembly function in the callstack.
It will work as long as the CFA pointer (frame pointer) location is not
modified (i.e. x29 is not touched in AArch64 state). It is the case in
almost all assembly functions, so this patch improves the average
debugging experience. Call stacks from the debugger should still be
interpreted with care. In more complex functions, one could use .cfi*
directives to inform the debugger about the new location of the CFA
pointer.
Change-Id: I9dabfbc033b45e8528e67f4823c17de7bf02fa24
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
In order to avoid unexpected traps into EL3/MON mode, this patch
resets the debug registers, MDCR_EL3 and MDCR_EL2 for AArch64,
and SDCR and HDCR for AArch32.
MDCR_EL3/SDCR is zero'ed when EL3/MON mode is entered, at the
start of BL1 and BL31/SMP_MIN.
For MDCR_EL2/HDCR, this patch zero's the bits that are
architecturally UNKNOWN values on reset. This is done when
exiting from EL3/MON mode but only on platforms that support
EL2/HYP mode but choose to exit to EL1/SVC mode.
FixesARM-software/tf-issues#430
Change-Id: Idb992232163c072faa08892251b5626ae4c3a5b6
Signed-off-by: David Cunado <david.cunado@arm.com>
The values of CP15BEN, nTWI & nTWE bits in SCTLR_EL1 are architecturally
unknown if EL3 is AARCH64 whereas they reset to 1 if EL3 is AArch32. This
might be a compatibility break for legacy AArch32 normal world software if
these bits are not set to 1 when EL3 is AArch64. This patch enables the
CP15BEN, nTWI and nTWE bits in the SCTLR_EL1 if the lower non-secure EL is
AArch32. This unifies the SCTLR settings for lower non-secure EL in AArch32
mode for both AArch64 and AArch32 builds of Trusted Firmware.
FixesARM-software/tf-issues#428
Change-Id: I3152d1580e4869c0ea745c5bd9da765f9c254947
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This include provides nothing useful for TF and prevents building
the fiptool using musl libc[0].
[0] https://www.musl-libc.org/
Change-Id: Ied35e16b9ea2b40213433f2a8185dddc59077884
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
In order to quantify the overall time spent in the PSCI software
implementation, an initial collection of PMF instrumentation points
has been added.
Instrumentation has been added to the following code paths:
- Entry to PSCI SMC handler. The timestamp is captured as early
as possible during the runtime exception and stored in memory
before entering the PSCI SMC handler.
- Exit from PSCI SMC handler. The timestamp is captured after
normal return from the PSCI SMC handler or if a low power state
was requested it is captured in the bl31 warm boot path before
return to normal world.
- Entry to low power state. The timestamp is captured before entry
to a low power state which implies either standby or power down.
As these power states are mutually exclusive, only one timestamp
is defined to describe both. It is possible to differentiate between
the two power states using the PSCI STAT interface.
- Exit from low power state. The timestamp is captured after a standby
or power up operation has completed.
To calculate the number of cycles spent running code in Trusted Firmware
one can perform the following calculation:
(exit_psci - enter_psci) - (exit_low_pwr - enter_low_pwr).
The resulting number of cycles can be converted to time given the
frequency of the counter.
Change-Id: Ie3b8f3d16409b6703747093b3a2d5c7429ad0166
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
This patch adds ARM SiP service for use by ARM standard platforms.
This service is added to support the SMC interface for the Performance
measurement framework(PMF).
Change-Id: I26f5712f9ab54f5f721dd4781e35a16f40aacc44
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
At present the `el3_entrypoint_common` macro uses `memcpy`
function defined in lib/stdlib/mem.c file, to copy data
from ROM to RAM for BL1. Depending on the compiler being
used the stack could potentially be used, in `memcpy`,
for storing the local variables. Since the stack is
initialized much later in `el3_entrypoint_common` it
may result in unknown behaviour.
This patch adds `memcpy4` function definition in assembly so
that it can be used before the stack is initialized and it
also replaces `memcpy` by `memcpy4` in `el3_entrypoint_common`
macro, to copy data from ROM to RAM for BL1.
Change-Id: I3357a0e8095f05f71bbbf0b185585d9499bfd5e0
This patch moves the invocation of `psci_setup()` from BL31 and SP_MIN
into `std_svc_setup()` as part of ARM Standard Service initialization.
This allows us to consolidate ARM Standard Service initializations which
will be added to in the future. A new function `get_arm_std_svc_args()`
is introduced to get arguments corresponding to each standard service.
This function must be implemented by the EL3 Runtime Firmware and both
SP_MIN and BL31 implement it.
Change-Id: I38e1b644f797fa4089b20574bd4a10f0419de184
This patch introduces a `psci_lib_args_t` structure which must be
passed into `psci_setup()` which is then used to initialize the PSCI
library. The `psci_lib_args_t` is a versioned structure so as to enable
compatibility checks during library initialization. Both BL31 and SP_MIN
are modified to use the new structure.
SP_MIN is also modified to add version string and build message as part
of its cold boot log just like the other BLs in Trusted Firmware.
NOTE: Please be aware that this patch modifies the prototype of
`psci_setup()`, which breaks compatibility with EL3 Runtime Firmware
(excluding BL31 and SP_MIN) integrated with the PSCI Library.
Change-Id: Ic3761db0b790760a7ad664d8a437c72ea5edbcd6
This patch adds ARM Cortex-A32 MPCore Processor support
in the CPU specific operations framework. It also includes
this support for the Base FVP port.
Change-Id: If3697b88678df737c29f79cf3fa1ea2cb6fa565d
This patch adds support in SP_MIN to receive generic and
platform specific arguments from BL2.
The new signature is as following:
void sp_min_early_platform_setup(void *from_bl2,
void *plat_params_from_bl2);
ARM platforms have been modified to use this support.
Note: Platforms may break if using old signature.
Default value for RESET_TO_SP_MIN is changed to 0.
Change-Id: I008d4b09fd3803c7b6231587ebf02a047bdba8d0
This patch adds generic changes in BL1 to support AArch32 state.
New AArch32 specific assembly/C files are introduced and
some files are moved to AArch32/64 specific folders.
BL1 for AArch64 is refactored but functionally identical.
BL1 executes in Secure Monitor mode in AArch32 state.
NOTE: BL1 in AArch32 state ONLY handles BL1_RUN_IMAGE SMC.
Change-Id: I6e2296374c7efbf3cf2aa1a0ce8de0732d8c98a5
This patch adds common changes to support AArch32 state in
BL1 and BL2. Following are the changes:
* Added functions for disabling MMU from Secure state.
* Added AArch32 specific SMC function.
* Added semihosting support.
* Added reporting of unhandled exceptions.
* Added uniprocessor stack support.
* Added `el3_entrypoint_common` macro that can be
shared by BL1 and BL32 (SP_MIN) BL stages. The
`el3_entrypoint_common` is similar to the AArch64
counterpart with the main difference in the assembly
instructions and the registers that are relevant to
AArch32 execution state.
* Enabled `LOAD_IMAGE_V2` flag in Makefile for
`ARCH=aarch32` and added check to make sure that
platform has not overridden to disable it.
Change-Id: I33c6d8dfefb2e5d142fdfd06a0f4a7332962e1a3
This patch adds changes in ARM platform code to use new
version of image loading.
Following are the major changes:
-Refactor the signatures for bl31_early_platform_setup()
and arm_bl31_early_platform_setup() function to use
`void *` instead of `bl31_params_t *`.
-Introduce `plat_arm_bl2_handle_scp_bl2()` to handle
loading of SCP_BL2 image from BL2.
-Remove usage of reserve_mem() function from
`arm_bl1_early_platform_setup()`
-Extract BL32 & BL33 entrypoint info, from the link list
passed by BL2, in `arm_bl31_early_platform_setup()`
-Provides weak definitions for following platform functions:
plat_get_bl_image_load_info
plat_get_next_bl_params
plat_flush_next_bl_params
bl2_plat_handle_post_image_load
-Instantiates a descriptor array for ARM platforms
describing image and entrypoint information for
`SCP_BL2`, `BL31`, `BL32` and `BL33` images.
All the above changes are conditionally compiled using the
`LOAD_IMAGE_V2` flag.
Change-Id: I5e88b9785a3df1a2b2bbbb37d85b8e353ca61049
This patch adds changes in BL1 & BL2 to use new version
of image loading to load the BL images.
Following are the changes in BL1:
-Use new version of load_auth_image() to load BL2
-Modified `bl1_init_bl2_mem_layout()` to remove using
`reserve_mem()` and to calculate `bl2_mem_layout`.
`bl2_mem_layout` calculation now assumes that BL1 RW
data is at the top of the bl1_mem_layout, which is more
restrictive than the previous BL1 behaviour.
Following are the changes in BL2:
-The `bl2_main.c` is refactored and all the functions
for loading BLxx images are now moved to `bl2_image_load.c`
`bl2_main.c` now calls a top level `bl2_load_images()` to
load all the images that are applicable in BL2.
-Added new file `bl2_image_load_v2.c` that uses new version
of image loading to load the BL images in BL2.
All the above changes are conditionally compiled using the
`LOAD_IMAGE_V2` flag.
Change-Id: Ic6dcde5a484495bdc05526d9121c59fa50c1bf23
This patch adds capability to load BL images based on image
descriptors instead of hard coded way of loading BL images.
This framework is designed such that it can be readily adapted
by any BL stage that needs to load images.
In order to provide the above capability the following new
platform functions are introduced:
bl_load_info_t *plat_get_bl_image_load_info(void);
This function returns pointer to the list of images that the
platform has populated to load.
bl_params_t *plat_get_next_bl_params(void);
This function returns a pointer to the shared memory that the
platform has kept aside to pass trusted firmware related
information that next BL image needs.
void plat_flush_next_bl_params(void);
This function flushes to main memory all the params that
are passed to next image.
int bl2_plat_handle_post_image_load(unsigned int image_id)
This function can be used by the platforms to update/use
image information for given `image_id`.
`desc_image_load.c` contains utility functions which can be used
by the platforms to generate, load and executable, image list
based on the registered image descriptors.
This patch also adds new version of `load_image/load_auth_image`
functions in-order to achieve the above capability.
Following are the changes for the new version as compared to old:
- Refactor the signature and only keep image_id and image_info_t
arguments. Removed image_base argument as it is already passed
through image_info_t. Given that the BL image base addresses and
limit/size are already provided by the platforms, the meminfo_t
and entry_point_info arguments are not needed to provide/reserve
the extent of free memory for the given BL image.
- Added check for the image size against the defined max size.
This is needed because the image size could come from an
unauthenticated source (e.g. the FIP header).
To make this check, new member is added to the image_info_t
struct for identifying the image maximum size.
New flag `LOAD_IMAGE_V2` is added in the Makefile.
Default value is 0.
NOTE: `TRUSTED_BOARD_BOOT` is currently not supported when
`LOAD_IMAGE_V2` is enabled.
Change-Id: Ia7b643f4817a170d5a2fbf479b9bc12e63112e79
This patch implements CSS platform hook to support NODE_HW_STATE PSCI
API. The platform hook queries SCP to obtain CSS power state. Power
states returned by SCP are then converted to expected PSCI return codes.
Juno's PSCI operation structure is modified to use the CSS
implementation.
Change-Id: I4a5edac0e5895dd77b51398cbd78f934831dafc0
This patch adds support for NODE_HW_STATE PSCI API by introducing a new
PSCI platform hook (get_node_hw_state). The implementation validates
supplied arguments, and then invokes this platform-defined hook and
returns its result to the caller. PSCI capabilities are updated
accordingly.
Also updates porting and firmware design guides.
Change-Id: I808e55bdf0c157002a7c104b875779fe50a68a30
This patch adds a couple of missing forward declarations in plat_arm.h
so that all types it references are known within this header file,
without relying on previous header inclusions. This concerns the
meminfo and bl31_params structures, which are defined in bl_common.h.
Other external types referenced from plat_arm.h (e.g. mmap_region_t)
get declared through header files included by arm_plat.h so they
don't need forward declarations.
Change-Id: I471d5aa487919aff3fa979fc65e053f4f5b0ef32
Commit e8719552a2 removed some definitions related to translation
tables from the xlat_tables.h header file, based on the assumption
that they weren't used by any platform. These are actually used by
some partners so this patch restores them.
FixesARM-software/tf-issues#425
Change-Id: Idafa5f00bb0bd9c2847b5ae6541cf8db93c7b89a
When using more than a single service in PMF, it is necessary that the
per-service timestamps begin on a cache line boundary. Previously it
was possible that two services shared a cache line for their
timestamps. This made it difficult to reason about cache maintenance
operations within a single service and required a global understanding
of how all services operate.
Change-Id: Iacaae5154a7e19ad4107468e56df9ad082ee371c
Given the service name and timestamp id, this assembler macro
calculates the offset into a memory region where the per-cpu timestamp
value is located.
Change-Id: I47f6dfa2a17be182675e2ca0489d6eed42433209
More headers will be needed soon so better to move these to their own
directory to avoid cluttering include/lib.
Change-Id: I6a72dc5b602d6f51954cf60aadd1beb52a268670
Instead of hardcoding a level 1 table as the base translation level
table, let the code decide which level is the most appropriate given
the virtual address space size.
As the table granularity is 4 KB, this allows the code to select
level 0, 1 or 2 as base level for AArch64. This way, instead of
limiting the virtual address space width to 39-31 bits, widths of
48-25 bit can be used.
For AArch32, this change allows the code to select level 1 or 2
as the base translation level table and use virtual address space
width of 32-25 bits.
Also removed some unused definitions related to translation tables.
FixesARM-software/tf-issues#362
Change-Id: Ie3bb5d6d1a4730a26700b09827c79f37ca3cdb65
davidcunado-arm
dp-arm
Douglas Raillard
danh-arm
Jeenu Viswambharan
Antonio Nino Diaz
Sandrine Bailleux
Masahiro Yamada
Haojian Zhuang
Nishanth Menon
Yatharth Kochar
Soby Mathew
Qixiang.Xu
Leon Chen