Add support for ICC, sink mode, bypass mode,
active discharge and list voltages.
Handle LDO3 sink source mode in a different way to avoid
setting voltage while in sink source mode.
Change-Id: Ib1b909fd8a153f542917f650e43e24317a570534
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Add regulators boost, pwr_sw1 and pwr_sw2 regulators related to
USB OTG supply BOOST, SW_OTG and SWIN/SWOUT. These regulators are
needed since manipulated during the suspend/resume power sequence
as per FDT description for stm32mp15x-xxx boards from
STMicroelectronics.
Change-Id: I6217de707e49882bd5a9100db43e0d354908800d
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
This is mainly a clock interface with clk_ops callbacks.
Those callbacks are: enable, disable, get_rate, set_parent,
and is_enabled.
This framework is compiled for STM32MP1.
Change-Id: I5119a2aeaf103ceaae7a60d9e423caf0c148d794
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Add set_gpio_reset_cfg() to set a pin in its reset configuration:
analog, no-pull, speed low, and its secure configuration, thanks to
stm32_gpio_is_secure_at_reset().
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I7b73c3636859f97fcc57f81cf68b42efc727922e
Implemented a platform function 'plat_mboot_measure_critical_data' to
measure critical data and record its measurement using the Event Log
driver.
'bl2_plat_mboot_finish' function invokes this platform function
immediately after populating the critical data.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ia198295c6e07ab26d436eab1ff90df2cf28303af
It doesn't look correct to use mbed TLS defines directly in the Event
Log driver as this driver may use another Crypto library in future.
Hence mbed TLS Crypto dependency on Event Log driver is removed by
introducing generic Crypto defines and uses those in the Event Log
driver to call Crypto functions.
Also, updated mbed TLS glue layer to map these generic Crypto defines
to mbed TLS library defines.
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ibc9c751f60cbce4d3f3cf049b7c53b3d05cc6735
Add a UART/USART driver for STM32 with complete a hardware support;
it used for STM32CubeProgrammer support with even parity.
This driver is not used for console, which is already handle
by a simple driver (drivers/st/uart/aarch32/stm32_console.S).
Change-Id: Ia9266e5d177fe7fd09c8a15b81da1a05b1bc8b2d
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Sometimes when changing UART clock from TBG to XTAL, UART HW enters into
some broken state. It does not transit characters from TX FIFO anymore
and TX FIFO stays always empty. TX FIFO reset does not recover UART HW
from this broken state.
Experiments show that external reset can fix UART HW from this broken
state.
TF-A fatal error handler calls console_a3700_core_init() function to
initialize UART HW. This handler may be called anytime during CPU
runtime, also when kernel is running.
U-Boot or Linux kernel may change UART clock to TBG to achieve higher
baudrates. During initialization, console_a3700_core_init() resets UART
configuration to default settings, which means that it also changes
UART clock from TBG to XTAL.
Do an external reset of UART via North Bridge Peripheral reset register
to prevent this UART hangup.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I8990bce24d1a6fd8ccc47a2cd0a5ff932fcfcf14
Renamed a macro 'INVALID_ID' to 'EVLOG_INVALID_ID' to avoid its clash
with other macro names and to show it is explicitly used for Event
Log driver.
Change-Id: Ie4c92b3cd1366d9a59cd6f43221e24734865f427
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Correctly handle USB_DESC_TYPE_OTHER_SPEED_CONFIGURATION request
in USB driver and support a different result than
USB_DESC_TYPE_CONFIGURATION with the new optional ops
get_other_speed_config_desc().
The support of this descriptor is optionnal and is only
required when high-speed capable device which can operate at its
other possible speed.
This patch allows to remove the pbuf update in usb_core_get_desc()
and solves an issue on USB re-enumeration on STM32MP15 platform
as the result of get_config_desc() is a const array.
This issue is not see on normal use-case, as the USB enumeration
is only done in ROM code and TF-A reuse the same USB descritors.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: I8edcc1e45065ab4e45d48f4bc37b49120674fdb0
When an Arm Ltd GIC (Arm GIC-[567]00) is instantiated with one or more
ITSes, the ITS MMIO frames appear between the distributor and
redistributor addresses. This makes the beginning of the redistributor
region dependent on the existence and number of ITSes.
To support various FPGA images, with and without ITSes, probe the
addresses in question, to learn whether they accommodate an ITS or a
redistributor. This can be safely done by looking at the PIDR[01]
registers, which contain an ID code for each region, documented in the
Arm GIC TRMs.
We try to find all ITSes instantiated, and skip either two or four 64K
frames, depending on GICv4.1 support. At some point we will find the
first redistributor; this address we then update in the DTB.
Change-Id: Iefb88c2afa989e044fe0b36b7020b56538c60b07
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The GIC specification describes ID registers in each GIC register frame
(PIDRx), which can be used to identify a GIC component. The Arm Ltd. GIC
implementations use certain ID values to identify the distributor, the
redistributors and other parts like ITSes.
Introduce a function that reads those part number IDs, which are spread
over two registers. The actual numbers are only meaningful in connection
with a certain GIC model, which would need to be checked beforehand, by
the caller.
Change-Id: Ia6ff326a1e8b12664e4637bc8e2683d2b5c7721c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add a device driver for Synopsis DWC2 USB IP of STM32MP15x,
this USB OTG device is only supported in device mode.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: I90b21f094f6637b85f3ace23a3a3a2f6fd4e0951
Add a new USB framework to manage an USB device profile (USBD)
based on a peripheral controller driver (PCD).
This USB stack can be use to implement any Universal Serial Bus Device
Class in TF-A on top of a USB driver defined in the platform.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: I7971ec6d952edec3511157a198e6e5359df4346b
This change aims to make the UFS code more robust by performing a
controller reset if linkstartup fails. This idea was borrowed from
Linux's ufshcd_link_startup function.
Signed-off-by: Jorge Troncoso <jatron@google.com>
Change-Id: I6b52148d1bf155b11198dc82a39b1120057adaaf
This change aims to make the UFS code more robust by adding retry logic
and timeouts to ufshc_reset. We also define a new function
ufshc_hce_enable for Host Controller Enable (HCE). The inner and outer
retry pattern is based on Linux's ufshcd_hba_execute_hce function.
Signed-off-by: Jorge Troncoso <jatron@google.com>
Change-Id: I9403a5a25d3ca50af5f2f9a65b774f6a2d7a9626
This change aims to make the UFS code more robust by removing asserts
and adding retry logic. We also reduce repetition by reusing
ufshc_send_uic_cmd for DME_GET and DME_SET commands.
Signed-off-by: Jorge Troncoso <jatron@google.com>
Change-Id: Id70aa1687d5ca78dc7d47234372255ac5a04a612
* changes:
fix(stpmic1): fix power switches activation
fix(stpmic1): update error cases return
refactor(stpmic1): use BIT and GENMASK helpers
fix(stm32mp1_clk): keep RTC clock always on
fix(stm32mp1_clk): set other clocks as always on
Currently, for the supported SCMI protocols, the version returned by the SCMI
platform agent must be exactly matching the driver's version (major version).
The recent change for the required version of Power Domain protocol means that
the platform must return version 2.0. This can be however a limitation in some
cases, where a SCMI-v1.0 platform can still be considered compatible with the
driver supported in firmware.
Relax the protocol version requirement such that any version older than the
one supported by the drivers can still be compatible.
Note: For now this has effect only on Power Domain protocol, as the other
drivers still require the "base" version 1.0.
Signed-off-by: Nicola Mazzucato <nicola.mazzucato@arm.com>
Change-Id: I310ae1869c2e952991a8d733f394029ab64087bf
Made measurement strings compliant to Server Base Security Guide
(SBSG, Arm DEN 0086) hence updated measurement strings for BL32, BL31,
and SCP_BL2 images. As the GPT image is not get measured by BL2 so
removed its measurement string.
Also, namespaced measurement string defines that were looking quite
generic.
Change-Id: Iaa17c0cfeee3d06dc822eff2bd553da23bd99b76
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
It looks safer and cleaner approach to record the measurement taken by
BL1 straightaway in TCG Event Log instead of deferring these recordings
to BL2.
Hence pull in the full-fledged measured boot driver into BL1 that
replaces the former ad-hoc platform interfaces i.e.
bl1_plat_set_bl2_hash, bl2_plat_get_hash.
As a result of this change the BL1 of Arm FVP platform now do the
measurements and recordings of below images:
1. FW_CONFIG
2. TB_FW_CONFIG
3. BL2
Change-Id: I798c20336308b5e91b547da4f8ed57c24d490731
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Currently, the Event Log driver does platform layer work by invoking
a few platform functions in the 'event_log_finalise' call. Doing
platform work does not seem to be the driver's responsibility, hence
moved 'event_log_finalise' function's implementation to the platform
layer.
Alongside, introduced few Event Log driver functions and done
some cosmetic changes.
Change-Id: I486160e17e5b0677c734fd202af7ccd85476a551
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Right now, event_log_init() does 2 things:
1) It writes all the necessary TCG data structures in the event log buffer.
2) It writes the first measurement (BL2's).
Step 2) introduces in the TCG event log driver an assumption on what
is getting measured and in what order. Ideally, the driver should only
be concerned about generic operations, such as initializing the event
log or recording a measurement in it. As much as possible, we should
design the driver such that it could be reused in another project that
has a different measure boot flow.
For these reasons, move step 2) up to the caller, plat_mboot_init() in
this case. Make event_log_record() a public function for this purpose.
This refactoring will also help when we make BL1 record BL2's
measurement into the event log (instead of BL2). Both BL1 and BL2 will
need to call the driver's init function but only BL1 will need
recording BL2's measurement. We can handle this through different
implementations of plat_mboot_init() for BL1 and BL2, leaving the TCG
event log driver unchanged.
Change-Id: I358e097c1eedb54f82b866548dfc6bcade83d519
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
With the removal of the generic functions measured_boot_init()/finish(),
measured_boot.mk becomes specific to the TCG event log backend. Change
its file name to event_log.mk.
Also, the Event Log driver is one of the backend of measured boot hence
created a separate folder for it under the measured_boot directory.
Alongside done some cosmetic changes (adding a comment and fixing
identation).
Change-Id: I4ce3300e6958728dc15ca5cced09eaa01510606c
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Right now, the measured boot driver is strongly coupled with the TCG
event log driver. It would not be possible to push the measurements
somewhere else, for instance to a physical TPM.
To enable this latter use case, turn the driver's init and teardown
functions into platform hooks. Call them bl2_plat_mboot_init()/finish().
This allows each platform to implement them appropriately, depending on
the type of measured boot backend they use. For example, on a platform
with a physical TPM, the plat_mboot_init() hook would startup the TPM
and setup it underlying bus (e.g. SPI).
Move the current implementation of the init and teardown function to the
FVP platform layer.
Finally move the conditional compilation logic (#if MEASURED_BOOT) out
of bl2_main() to improve its readability. Provide a dummy implementation
in the case measured boot is not included in the build.
Change-Id: Ib6474cb5a9c1e3d4a30c7f228431b22d1a6e85e3
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
tpm_record_measurement() function name suggests that:
- It only records a measurement but does not compute it.
This is not the case, the function does both.
- It stores this measurement into a TPM (discrete chip or fTPM).
This is not the case either, the measurement is just stored into
the event log, which is a data structure hold in memory, there is
no TPM involvement here.
To better convey the intent of the function, rename it into
event_log_measure_and_record().
Change-Id: I0102eeda477d6c6761151ac96759b31b6997e9fb
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Now lx2 which use MT35XU512A supports warm boot, fix the macro
define caused by the commit:
feat(driver/nxp/xspi): add MT35XU02G flash info
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I83eb8cb9a30ac7c7efd5a010acbd03eddebed52b
Use BIT and GENMASK macros to ease stpmic1.h reading.
Change-Id: I808a62818d4188bb2f3686ab37518d369b6c41cb
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Add support for Arm Ethos-N NPU multi-device.
The device tree parsing currently only supports one NPU device with
multiple cores. To be able to support multi-device NPU configurations
this patch adds support for having multiple NPU devices in the device
tree.
To be able to support multiple NPU devices in the SMC API, it has been
changed in an incompatible way so the API version has been bumped.
Signed-off-by: Laurent Carlier <laurent.carlier@arm.com>
Change-Id: Ide279ce949bd06e8939268b9601c267e45f3edc3
Change the fdt_get_rcc_node function to static, as it is used only in
stm32mp_clkfunc.c file; it is only a cleanup change without functional
modification.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Change-Id: Ib4ef110f6f1b16dbaa727a065e40275d3cf58a73
The file is first generated with the peripheral spirit XML file.
And then we add some common definition, to ease driver development.
Change-Id: I4c222cf006caf27cda6da044eaf184ce66bb1442
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Define RSTCR_RESET_REQ for Chassis V3.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I5cb7019baae5fe0d06b3d5e65f185f87ee16ad3a
Add a new function that allows to enable or disabled filters on
configured regions dynamically. This will avoid the need to
reconfigure the entire attribute and just manage to
enable/disable filters.
Change-Id: If0937ca755bec6c45d3649718147108459682fff
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
The FMU is part of the GIC Distributor (GICD) component. It implements
the following functionality in GIC-600AE:
* Provides software the means to enable or disable a Safety Mechanism
within a GIC block.
* Receives error signaling from all Safety Mechanisms within other GIC
blocks.
* Maintains error records for each GIC block, for software inspection
and provides information on the source of the error.
* Retains error records across functional reset.
* Enables software error recovery testing by providing error injection
capabilities in a Safety Mechanism.
This patch introduces support to enable error detection for all safety
mechanisms provided by the FMU. Platforms are expected to invoke the
initialization function during cold boot.
The support for the FMU is guarded by the GICV3_SUPPORT_GIC600AE_FMU
makefile variable. The default value of this variable is '0'.
Change-Id: I421c3d059624ddefd174cb1140a2d2a2296be0c6
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
At the moment we have a GIC_ENABLE_V4_EXTN build time variable to
determine whether the GIC interrupt controller is compliant to version
4.0 of the spec or not. This just changes the number of 64K MMIO pages
we expect per redistributor.
To support firmware builds which run on variable systems (emulators,
fast model or FPGAs), let's make this decision at runtime.
The GIC specification provides several architected flags to learn the
size of the MMIO frame per redistributor, we use GICR_TYPER[VLPI] here.
Provide a (static inline) function to return the size of each
redistributor.
We keep the GIC_ENABLE_V4_EXTN build time variable around, but change
its meaning to enable this autodetection code. Systems not defining this
rely on a "pure" GICv3 (as before), but platforms setting it to "1" can
now deal with both configurations.
Change-Id: I9ede4acf058846157a0a9e2ef6103bf07c7655d9
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For the GIC power management we need to identify certain GIC
implementations, so we have the IIDR values for some Arm Ltd. GIC models
defined.
We will need those number elsewhere very soon, so export them to a
shared header file, to avoid defining them again.
Change-Id: I1b8e2d93d6cea0d066866143c89eef736231134f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
1. Refined struct soc_info_t definition.
2. Refined get_soc_info function.
3. Fixed some SVR persernality value.
4. Refined API to get cluster numbers and cores per cluster.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I3c20611a523516cc63330dce4c925e6cda1e93c4
* changes:
feat(io_mtd): offset management for FIP usage
feat(nand): count bad blocks before a given offset
feat(plat/st): add helper to save boot interface
fix(plat/st): improve DDR get size function
refactor(plat/st): map DDR secure at boot
refactor(plat/st): rework TZC400 configuration
NXP drivers header files are moved:
- from: drivers/nxp/<xx>/*.h
- to : include/drivers/nxp/<xx>/*.h
To accommodate these changes each drivers makefiles
drivers/nxp/<xx>/xx.mk, are updated.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I3979c509724d87e3d631a03dbafda1ee5ef07d21
Implemented FWU metadata load and verification APIs.
Also, exported below APIs to the platform:
1. fwu_init - Load FWU metadata in a structure. Also, set the
addresses of updated components in I/O policy
2. fwu_is_trial_run_state - To detect trial run or regular run
state
Change-Id: I67eeabb52d9275ac83be635306997b7c353727cd
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Added a firmware update metadata structure as per section 4.1
in the specification document[1].
Also, added the build options used in defining the firmware
update metadata structure.
[1]: https://developer.arm.com/documentation/den0118/a/
Change-Id: I8f43264a46fde777ceae7fd2a5bb0326f1711928
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
A new seek handler is also created. It will be used for NAND to add an
extra offset in case of bad blocks, when FIP is used.
Change-Id: I03fb1588b44029db50583c0b2e7af7a1e88a5a7a
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
In case of FIP, the offsets given in the FIP header are relative.
If bad blocks are found between the FIP base address and this offset,
the offset should be updated, taking care of the bad blocks.
Change-Id: I96fefabb583b3d030ab05191bae7d45cfeefe341
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Use dedicated read function for boot partition
Signed-off-by: Vyacheslav Yurkov <uvv.mail@gmail.com>
Change-Id: If75df7691fce0797205365736fc6e4e3429efdca
Added a public function to read blocks from a current boot partition.
switch between partitions has to respect eMMC partition switch timing.
Signed-off-by: Vyacheslav Yurkov <uvv.mail@gmail.com>
Change-Id: I55b0c910314253e5647486609583fd290dadd30a
By default the Arm Ethos-N NPU will boot up in secure mode. In this mode
the non-secure world cannot access the registers needed to use the NPU.
To still allow the non-secure world to use the NPU, a SiP service has
been added that can delegate non-secure access to the registers needed
to use it.
Only the HW_CONFIG for the Arm Juno platform has been updated to include
the device tree for the NPU and the platform currently only loads the
HW_CONFIG in AArch64 builds.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I65dfd864042ed43faae0a259dcf319cbadb5f3d2
The SCMI power domain protocol in firmware has been updated to v2.0,
thus update the corresponding version in TF-A too.
Signed-off-by: Nicola Mazzucato <nicola.mazzucato@arm.com>
Change-Id: If3920ff71136dce94b2780e29a47f24aa09876c0
The legacy console is gone. Re-add DCC console support based
on the multi-console framework.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Ia8388721093bc1be3af40974530d7c9a9ae5f43e
Broadcom I2C controller driver. Follwoing API's are supported:-
- i2c_init() Intialize ethe I2C controller
- i2c_probe()
- i2c_set_bus_speed() Set the I2C bus speed
- i2c_get_bus_speed() Get the current bus speed
- i2c_recv_byte() Receive one byte of data.
- i2c_send_byte() Send one byteof data
- i2c_read_byte() Read single byte of data
- i2c_read() Read multiple bytes of data
- i2c_write_byte Write single byte of data
- i2c_write() Write multiple bytes of data
This driver is verified by reading the DDR SPD data.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Change-Id: I2d7fe53950e8b12fab19d0293020523ff8b74e13
NXP SMMU driver API for NXP SoC.
- Currently it supports by-passing SMMU, called only when NXP CAAM
is enabled.
- (TBD) AMQ based SMMU access control: Access Management Qualifiers (AMQ)
advertised by a bus master for a given transaction.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I23a12928ddedb1a2cf4b396606e35c67e016e331
Flexspi driver now introduces read/write/erase APIs for complete flash
size, FAST-READ are by default used and IP bus is used for erase, read
and write using flexspi APIs.
Framework layer is currently embedded in driver itself using flash_info
defines.
Test cases are also added to confirm flash functionality currently under
DEBUG flag.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Change-Id: I755c0f763f6297a35cad6885f84640de50f51bb0
A new function tzc400_it_handler() is created to manage TZC400
interrupts. The required helpers to read and clear interrupts are added
as well.
In case DEBUG is enabled, more information about the faulty access
(address, NSAID, type of access) is displayed.
Change-Id: Ie9ab1c199a8f12b2c9472d7120efbdf35711284a
Signed-off-by: Yann Gautier <yann.gautier@st.com>
* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mapping at BLE stage
plat/marvell/armada/common/mss: use MSS SRAM in secure mode
include/drivers/marvell/mochi: add detection of secure mode
plat/marvell: fix SPD handling in dram port
marvell: drivers: move XOR0/1 DIOB from WIN 0 to 1
drivers/marvell/mochi: add support for cn913x in PCIe EP mode
drivers/marvell/mochi: add missing stream IDs configurations
plat/marvell/armada/a8k: support HW RNG by SMC
drivers/rambus: add TRNG-IP-76 driver
Add Rambus (InsideSecure) TRNG-IP-76 HW RNG driver.
This IP is part of Marvell Armada CP110/CP115 die integrated
to Armada 7k/8K/CN913x SoCs
Change-Id: I9c5f510ad6728c7ed168da43d85b19d5852cd873
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
The filters parameter passed to tzc400_configure_region() is supposed
to be filter bit flag without bit shift, so the macros
TZC_400_REGION_ATTR_FILTER_BIT and TZC_400_REGION_ATTR_FILTER_BIT_ALL
should always construct the value without any shift.
It is not a functional issue for TZC_REGION_ATTR_F_EN_SHIFT is lucky
to be 0.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I5d363c462b8517256523f637e670eefa56722afd
In DDR controller PWRTMG register, the mask for field SELFREF_TO_X32 is
wrong. This field is from bit 16 to 23.
Change-Id: Id336fb08c88f0a153df186dd819e41af72febb88
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This patch does not change code, it only updates comments and macro name
for 6th bit of Status Register. So TF-A binary stay same.
6th bit of the Status Register is named TX EMPTY and is set to 1 when both
Transmitter Holding Register (THR) or Transmitter Shift Register (TSR) are
empty. It is when all characters were already transmitted.
There is also TX FIFO EMPTY bit in the Status Register which is set to 1
only when THR is empty.
In both console_a3700_core_init() and console_a3700_core_flush() functions
we should wait until both THR and TSR are empty therefore we should check
6th bit of the Status Register.
So current code is correct, just had misleading macro names and comments.
This change fixes this "documentation" issue, fixes macro name for 6th bit
of the Status Register and also updates comments.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I19e4e7f53a90bcfb318e6dd1b1249b6cbf81c4d3
Implementation is simple, just check if there is a pending character in
RX FIFO via RXRDY bit of Status Register and if yes, read it from
UART_RX_REG register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I226b6e336f44f5d0ca8dcb68e49a68e8f2f49708
Write char if fifo is empty. If this is done like this all chars are
printed. Because origin code just put that chars to fifo and in case of
reset messages were missing.
Before this change chars are put to fifo and only check before adding if
fifo is full. The patch is changing this logic that it is adding char only
when fifo is empty to make sure that in case of reset (by another SW for
example) all chars are printed. Maybe one char can be missed but for IP
itself it is much easier to send just one char compare to full fifo.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Ic24c2c1252bce24be2aed68ee29477ca4a549e5f
This gives the rich OS the flexibility to choose between I2C and RSB
communication. Since a runtime address can only be assigned once after
entering RSB mode, it also lets the rich OS choose any runtime address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Id49c124c5e925985fc31c0ba38c7fb6c941aafa8
Retrieve peripheral base address from a define instead of
parsing the device tree. The goal is to improve execution time.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I2588c53ad3d4abcc3d7fe156458434a7940dd72b
And from crash_console_flush.
We ignore the error information return by console_flush in _every_
place where we call it, and casting the return type to void does not
work around the MISRA violation that this causes. Instead, we collect
the error information from the driver (to avoid changing that API), and
don't return it to the caller.
Change-Id: I1e35afe01764d5c8f0efd04f8949d333ffb688c1
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
This patch migrates the mbedcrypto dependency for TF-A
to mbedTLS repo v2.24.0 which is the latest release tag.
The relevant documentation is updated to reflect the
use of new version.
Change-Id: I116f44242e8c98e856416ea871d11abd3234dac1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
A GICv3 interrupt controller will be instantiated for a certain number
of cores. This will result in the respective number of GICR frames. The
last frame will have the "Last" bit set in its GICR_TYPER register.
For platforms with a topology unknown at build time (the Arm FPGAs, for
instance), we need to learn the number of used cores at runtime, to size
the GICR region in the devicetree accordingly.
Add a generic function that iterates over all GICR frames until it
encounters one with the "Last" bit set. It returns the number of cores
the GICv3 has been configured for.
Change-Id: I79f033c50dfc1c275aba7122725868811abcc4f8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Depending on compiler, the issue about bool or uint*_t not defined can
appear.
Correct this by adding stdbool.h and stdint.h includes in etzpc.h.
Change-Id: If1419dc511efbe682459fa4a776481fa52a38aa3
Signed-off-by: Yann Gautier <yann.gautier@st.com>
nand_wait_ready is called with a millisecond delay
but the timeout used a micro second. Fixing the conversion
in the timeout call.
The prototype of the function is also changed to use an unsigned int
parameter.
Change-Id: Ia3281be7980477dfbfdb842308d35ecd8b926fb8
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Builds in Debug mode with Measured Boot enabled might run out of trusted
SRAM. This patch allows to change the Log Level at which the Measured Boot
driver will dump the event log, so the latter can be accessed even on
Release builds if necessary, saving space on RAM.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I133689e313776cb3f231b774c26cbca4760fa120