Update WA for Errata A-050426 as Commands for
PEX (PEX1..PEX6) , lnx1_e1000#0, lnx1_xfi and
lnx2_xfi has been moved to PBI phase.
This patch requires RCW to include PBI commands
to write commands in BIST mode for PEX, lnx1_e1000,
lnx1_xfi and lnx2_xfi IP blocks.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Change-Id: I27c2b055c82c0b58df83449f9082bfbfdeb65115
In anticipation of Spectre BHB workaround mitigation patches, we
disable the RECLAIM_INIT_CODE for FVP platform. Since the spectre
BHB mitigation workarounds inevitably increase the size of the various
segments due to additional instructions and/or macros, these segments
cannot be fit in the existing memory layout designated for BL31 image.
The issue is specifically seen in complex build configs for FVP
platform. One such config has TBB with Dual CoT and test secure
payload dispatcher(TSPD) enabled. Even a small increase in individual
segment size in order of few bytes might lead to build fails due to
alignment requirements(PAGE_ALIGN to 4KB).
This is needed to workaround the following build failures observed
across multiple build configs:
aarch64-none-elf-ld.bfd: BL31 init has exceeded progbits limit.
aarch64-none-elf-ld.bfd: /work/workspace/workspace/tf-worker_ws_2/trusted_firmware/build/fvp/debug/bl31/bl31.elf section coherent_ram will not fit in region RAM
aarch64-none-elf-ld.bfd: BL31 image has exceeded its limit.
aarch64-none-elf-ld.bfd: region RAM overflowed by 4096 bytes
Change-Id: Idfab539e9a40f4346ee11eea1e618c97e93e19a1
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
This allows TF-A's a3700_system_reset() function to try Warm reset
method when CM3 reset method is not implemented by WTMI firmware.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I7303197373e1a8ca5a44ba0b1e90b48855d6c0c3
* changes:
Revert "feat(sgi): deviate from arm css common uart related defi..."
Revert "feat(sgi): route TF-A logs via secure uart"
Revert "feat(sgi): add page table translation entry for secure uart"
Revert submission 14286-uart_segregation
Reason for revert: Need to wait for companion patches in CI and UEFI/Linux to be upstreamed.
Reverted Changes:
I8574b31d5:feat(sgi): add page table translation entry for se...
I8896ae05e:feat(sgi): route TF-A logs via secure uart
I39170848e:feat(sgi): deviate from arm css common uart relate...
Change-Id: I28a370dd8b3a37087da621460eccc1acd7a30287
Revert submission 14286-uart_segregation
Reason for revert: Need to wait for companion patches in CI and UEFI/Linux to be upstreamed.
Reverted Changes:
I8574b31d5:feat(sgi): add page table translation entry for se...
I8896ae05e:feat(sgi): route TF-A logs via secure uart
I39170848e:feat(sgi): deviate from arm css common uart relate...
Change-Id: I7c488aed9fcb70c55686d705431b3fe017b8927d
Revert submission 14286-uart_segregation
Reason for revert: Need to wait for companion patches in CI and UEFI/Linux to be upstreamed.
Reverted Changes:
I8574b31d5:feat(sgi): add page table translation entry for se...
I8896ae05e:feat(sgi): route TF-A logs via secure uart
I39170848e:feat(sgi): deviate from arm css common uart relate...
Change-Id: I9bec02496f826e184c6efa643f869b2eb3b52539
DFD (Design for Debug) is a debugging tool, which scans flip-flops and
dumps to internal RAM on the WDT reset. After system reboots, those
values could be showed for debugging.
BUG=b:222217317
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I659ea1e0789cf135a71a13b752edaa35123e0941
When trying to boot from an SD card with STM32MP_EMMC_BOOT enabled,
booting fails with:
ERROR: Got unexpected value for active boot partition, 0
ASSERT: plat/st/common/bl2_stm32_io_storage.c:285
because SD cards don't provide a boot partition. So only try reading
from such a partition when booting from eMMC.
Fixes: 214c8a8d08 ("feat(plat/st): add STM32MP_EMMC_BOOT option")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Change-Id: I354b737a3ae3ea577e83dfeb7096df22275d852d
* changes:
feat(sgi): add page table translation entry for secure uart
feat(sgi): route TF-A logs via secure uart
feat(sgi): deviate from arm css common uart related definitions
Updated makefile so that build can accept absolute mbedTLS path.
Change-Id: Ife73266a01d7ed938aafc5e370240023237ebf61
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Updating call order for arm_console_boot_init() and arm_bl31_early_platform_setup().
Signed-off-by: Juan Pablo Conde <juanpablo.conde@arm.com>
Change-Id: If932fff2ee4282a0aacf8751fa81e7665b886467
Patch [1] introduces a mechanism to provide the platform
specified mbedTLS config file, but that result in build failure
for Broadcom platform.
This build failure is due to the absence of the mbedTLS configuration
file i.e. brcm_mbedtls_config.h in the TF-A source code repository.
"fatal error: brcm_mbedtls_config.h: No such file or directory"
This problem was resolved by removing the 'brcm_mbedtls_config.h' entry
from the broadcom platform makefile, allowing this platform to use
the default mbedtls_config.h file.
[1]: https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/13726
Signed-off-by: Manish V Badarkhe <manish.badarkhe@arm.com>
Change-Id: I7cc2efc049aefd3ebce1ae513df9b265fe31ded6
Add page table translation entry for secure uart so that logs from
secure partition can be routed via the same.
Signed-off-by: Rohit Mathew <rohit.mathew@arm.com>
Change-Id: I8574b31d5d138d9f94972deb903124f8c5b70ce4
Route the boot, runtime and crash stage logs via secure UART port
instead of the existing use of non-secure UART. This aligns with the
security state the PE is in when logs are put out. In addition to this,
this allows consolidation of the UART related macros across all the
variants of the Neoverse reference design platforms.
Signed-off-by: Rohit Mathew <rohit.mathew@arm.com>
Change-Id: I8896ae05eaedf06dead520659375af0329f31015
The Neoverse reference design platforms will migrate to use different
set of secure and non-secure UART ports. This implies that the board
specific macros defined in the common Arm platform code will no longer
be usable for Neoverse reference design platforms.
In preparation for migrating to a different set of UART ports, add a
Neoverse reference design platform specific copy of the board
definitions. The value of these definitions will be changed in
subsequent patches.
Signed-off-by: Rohit Mathew <rohit.mathew@arm.com>
Change-Id: I39170848ecd81a7c1bbd3689bd905e45f9435f5c
* changes:
build(intel): enable access to on-chip ram in BL31 for N5X
fix(intel): make FPGA memory configurations platform specific
fix(intel): fix ECC Double Bit Error handling
build(intel): define a macro for SIMICS build
build(intel): add N5X as a new Intel platform
build(intel): initial commit for crypto driver
Remove reserved range for platform provider owned SPs if the dual root
CoT is disabled and allow SPs to populate the range up to MAX_SP_IDS.
Signed-off-by: Imre Kis <imre.kis@arm.com>
Change-Id: Ib4ec18f6530d2515ada21d2c0c388d55aa479d26
Following I2d274fa897171807e39b0ce9c8a28824ff424534:
Remove GICD registers S2 mapping from OP-TEE partition when it runs in a
secure partition on top of Hafnium.
The partition is not meant to access the GIC directly but use the
Hafnium provided interfaces.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I1a38101f6ae9911662828734a3c9572642123f32
Fix coding style violations and alignments:
- Remove additional newlines in headers
- Remove additional newlines in code
- Add newline to separate variable from the code
- Use the same indentation in platform.mk
- Align function parameters
- Use tabs for indentation in kernel-doc format
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I0b12804ff63bc19778e8f21041f9accba5b488b9
This adds the ncore ccu access and enable access to the
on-chip ram for N5X device in BL31.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: I713f6e93d33b6e91705547477ca32cfba5c8c13d
Define FPGA_CONFIG_SIZE and FPGA_CONFIG_ADDR in
platform-specific header. This is due to different
allocated sizes between platforms.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: Iac4fbf4d4940cdf31834a9d4332f9292870dee76
SError and Abort are handled in Linux (EL1) instead of
EL3. This patch adds some functionality that complements the
use cases by Linux as follows:
- Provide SMC for ECC DBE notification to EL3
- Determine type of reset needed and service the request in
place of Linux
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: I43d02c77f28004a31770be53599a5a42de412211
SIMICS builds have different UART configurations compared
to hardware build. Hence, this patch defines a macro to
differentiate between both.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: Iadecd5445e06611486ac3c6a214a6d0dc8ccd27b
This commit adds a new Intel platform called N5X.
This preliminary patch only have Bl31 support.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: Ib31f9c4a5a0dabdce81c1d5b0d4776188add7195
This patch adds driver for Intel FPGA's Crypto Services.
These services are provided by Intel platform
Secure Device Manager(SDM) and are made accessible by
processor components (ie ATF).
Below is the list of enabled features:
- Send SDM certificates
- Efuse provision data dump
- Encryption/decryption service
- Hardware IP random number generator
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: If7604cd1cacf27a38a9a29ec6b85b07385e1ea26
* changes:
fix(zynqmp): query node status to power up APU
feat(zynqmp): pm_api_clock_get_num_clocks cleanup
feat(zynqmp): add feature check support
fix(zynqmp): use common interface for eemi apis
feat(zynqmp): add support to get info of xilfpga
feat(zynqmp): pass ioctl calls to firmware
When the atf-handoff-params are updated we are returning
FSBL_HANDOFF_SUCCESS, but the return condition is wrongly
updated and added a error log which is incorrect.
Fixing the incorrect log message.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I44ebbb861831b86afcb87f09ddb2e23614393c28
Add the possibility to configure console UART baudrate, it can be passed
as a command line parameter with STM32MP_UART_BAUDRATE. The default value
remains 115200.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I000df70c10b2b4dac1449556596f9820c36cf243
If APU is in suspending state and if wakeup request comes then
PMUFW returns error which is not handled at ATF side.
To fix this, get the APU node status before calling wakeup and
return error if found in suspending state.
Here, we can not handle the error code of pm_req_wakeup() from PMUFW
because ATF is already calling pm_client_wakeup() before calling
pm_req_wakeup().
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I18d47384e46e22ae49e804093ad0641b7a6349e2
There is no reason to have even one additional useless line that's why
remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: Icc3c74249dfe64173aa5c88fb0f9ffe7576fc2aa
This API returns version of supported APIs.
Here, there are three cases to check API version by using feature
check implementation.
1. Completely implemented in TF-A: I mean the EEMI APIs which are
completely implemented in the TF-A only. So check those IDs and
return appropriate version for the same. Right now, it is base
version.
2. Completely implemented in firmware: I mean the EEMI APIs which are
completely implemented in the firmware only. Here, TF-A only passes
Linux request to the firmware to get the version of supported API. So
check those IDs and send request to firmware to get the version and
return to Linux if the version is supported or return the error code
if the feature is not supported.
3. Partially implemented (Implemented in TF-A and firmware both):
First check dependent EEMI API version with the expected version in
the TF-A. If the dependent EEMI API is supported in firmware then
return its version and check with the expected version in the TF-A.
If the version matches then check for the actual requested EEMI API
version. If the version is supported then return version of API
implemented in TF-A.
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I73f20d8222c518df1cda7879548b408b130b5b2e
Currently all EEMI API has its own implementation in TF-A which is
redundant. Most EEMI API implementation in TF-A does same work. It
prepares payload received from kernel, sends payload to firmware,
receives response from firmware and send response back to kernel.
So use common interface for EEMI APIs which has similar functionality.
This will optimize TF-A code.
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I07325644a1fae80211f2588d5807c21973f6d48f
Adds support to get the xilfpga library version and feature list info.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: Iff10ad2628a6a90230c18dc3aebf9dde89f53ecd
Firmware supports new IOCTL for different purposes. To avoid
maintaining new IOCTL IDs in ATF, pass IOCTL call to firmware
for IOCTL IDs implemented in firmware.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: Ie14697c8da9581b0f695f4d33f05161ece558385
Update the MAX_XLAT_TABLES as the memory map has been
added for the dtb to accomodate in DDR address.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I46225673f40f123cdab38efefb038604da119b58
Remove the time stamp and system counter configuration, as
this configuration is already done by the first stage bootloader.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I41554dc2e14d97954bff299df9740a5efa30fad9
With gcc-11, the -Wformat-signedness warning complains about enum values
that should be printed as unsigned values. But the current version of
compiler used in CI states that this parameter is signed. Just cast the
value then.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: Ic0655e5ba9c44fe6abcd9958d7a9972f5de3b7ef
* changes:
fix(intel): null pointer handling for resp_len
fix(intel): define macros to handle buffer entries
fix(intel): change SMC return arguments for INTEL_SIP_SMC_MBOX_SEND_CMD
fix(intel): always set doorbell to SDM after sending command
fix(intel): fix bit masking issue in intel_secure_reg_update
fix(intel): fix ddr address range checker
build(changelog): add new scope for Intel platform
Change resource_req to 0 to disable 26MHz clock.
SPM firmware will pull-down SRCLKENA0 after 26MHz off while suspending.
TEST=verify 26MHz clock off using the oscilloscope.
BUG=b:215639203
Signed-off-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Change-Id: I05702d14a015cabccd6d4af0e3f2a534fbe4dd12
* changes:
fix(nxp-crypto): refine code to avoid hang issue for some of toolchain
build(changelog): add new scope for nxp crypto
fix(lx2): drop erratum A-009810
Platforms which support Realm world cannot boot up
properly if measured boot is enabled at build time.
An assertions occurs due to the missing RMM entry
in the event_log_metadata array.
Signed-off-by: Tamas Ban <tamas.ban@arm.com>
Change-Id: I172f10a440797f7c9e1bc79dc72242b40c2521ea
Previous changes from commit #6a659448 updates resp_len from an integer
type to unsigned integer pointer type. This patch adds proper handling
in case resp_len is a null pointer. Resp_len with value 0 are also
changed to NULL to match the type change.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I75b3e3bfbb188d8e7b329ba3b948c23e31dec490
This patch defines a macro to handle Secure Device Manager's (SDM)
pointer to command & response buffer entries and convert them to the
correct physical address.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I4cf9f1d90e0d5ae4e1a2ce84165864b48c2862e7
'INTEL_SIP_SMC_MBOX_SEND_CMD' SMC runtime service will only return
mailbox status and the argument's length back to the caller
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Change-Id: I50d2ae74845794cab7bf0858e742b5a70e0ea868
This patch fixes the mailbox stall issue when sending mailbox command
that is larger than mailbox command FIFO size.
Large mailbox command will be sent to SDM in multiple chunks. HPS will
set doorbell to SDM when command FIFO full (is_doorbell_triggered will
be set to 1) to notify SDM to read the command data from FIFO, so that
HPS can continue to send the next chunk of command data.
However, HPS will not set the doorbell to SDM at the end if the doorbell
have been set earlier due to FIFO full. This will cause SDM mailbox
service stall because it is still waiting for last chunk of command data.
This patch fixes the code to always set the doorbell to SDM at the end
to get rid of stall issue.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change-Id: Idbe62410a00d92a30c7aeaa26d53d79a910cac0a
intel_secure_reg_update function should apply mask to the value before
write into register.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change-Id: I84bbd06e24b8666528b53030e8359743d438eb5b
This patch fix address range checker to make sure that it does not
errors out on NULL address with size 0. Non-secure software will send
this NULL address if the SMC call doesn't need to pass any address buffer.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I7e492c562a311ba989570c4ed465f845333ec865
This patch fixes the code issue detected by Klocwork scan. Pointer
'bl_mem_params' returned from call to function 'get_bl_mem_params_node'
may be NULL and the NULL pointer may be caused the system crash. Update
the code to assert if unexpected NULL pointer is returned.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change-Id: I00f3132a6104618cadce26aa303c0b46b5921d5b
Request ownership and direct access to QSPI by default in BL2.
Previously, this is only done on QSPI boot mode.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: Ie222bbf9d719f2f70f89d4739c285efe6df4c955
The erratum A-009810 should not be applied to LX2, the impaction is
that it can cause system reboot when linux tried to power down, so remove
it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I5e24229cf8512eff28b315ebcdf18de555c40c74
* changes:
docs(layerscape): add ls1046a soc and board support
feat(ls1046aqds): add board ls1046aqds support
feat(ls1046afrwy): add ls1046afrwy board support
feat(ls1046ardb): add ls1046ardb board support
feat(ls1046a): add new SoC platform ls1046a
fix(nxp-tools): fix tool location path for byte_swape
fix(nxp-qspi): fix include path for QSPI driver
build(changelog): add new scopes for NXP layerscape platforms
* changes:
feat(stm32mp1): enable format-signedness warning
fix(stm32mp1): correct types in messages
fix(st-pmic): correct verbose message
fix(st-sdmmc2): correct cmd_idx type in messages
fix(st-fmc): fix type in message
fix(mtd): correct types in messages
fix(usb): correct type in message
fix(tzc400): correct message with filter
fix(psci): correct parent_node type in messages
fix(libc): correct some messages
fix(fconf): correct image_id type in messages
fix(bl2): correct messages with image_id
Currently only the lowest 2 DRAM region were configured in the
TrustZone Controller, but the platform supports 6 regions spanning the
whole address space.
Configuring all of them to allow tests to access memory also in those
higher memory regions.
FVP memory map:
https://developer.arm.com/documentation/100964/1116/Base-Platform/Base---memory/Base-Platform-memory-map
Note that last row is wrong, describing a non-existing 56bit address,
all region labels should be shifted upward.
Issue has been reported and next release will be correct.
Change-Id: I695fe8e24aff67d75e74635ba32a133342289eb4
Signed-off-by: Federico Recanati <federico.recanati@arm.com>
Add initial support for RD-Edmunds platform. This platform is considered
as a variant of RD-N2 platform with only major change being the CPU
which is Demeter instead of Neoverse-N2.
Signed-off-by: Tony K Nadackal <tony.nadackal@arm.com>
Change-Id: I939d9eac652fa9e76ad002ee5e6107aa79baa013
Add the flag -Wformat-signedness to TF_CFLAGS for STM32MP1.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I6af18778902b0a4dae1c08735d2d070ef3d137ce
Secure enclave decides the boot bank based on the firmware update
state of the system and updates the boot bank information at a given
location in the flash. In this commit, bl2 reads the given flash
location to indentify the bank from which it should load fip from.
Signed-off-by: Satish Kumar <satish.kumar01@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Change-Id: I7f0f4ffc97189c9deb99db44afcd966082ffbf21
A53 AP BootROM is just 16 kB long and is mapped to address range
0xFFFF0000-0xFFFF4000. RVBAR_EL3 register has value 0xFFFF0000.
A53 AP BootROM itself is in the BootROM window which is 1 MB long and
mapped to address range 0xFFF00000-0xFFFFFFFF.
CM3 BootROM is not accessible from A53 core.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I5d4a4c7b1e7550c4738c67a872d341f945d48bbc
More space in the flash is reserved up front for metadata
parser and UEFI variables. That requires change in the flash
base address of where images are present.
Signed-off-by: Satish Kumar <satish.kumar01@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Change-Id: Ieaabe09374d707de18d36505c69b6c9a8c2ec2e9
This change implements platform specific psci reset
for the corstone1000.
Signed-off-by: Emekcan Aras <Emekcan.Aras@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Change-Id: I25f77234506416c3376ff4a028f6ea40ebe68437
ls1046aqds board is full function board to evaluate ls1046a platform.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Id1befe37a25f7c379e76791538348fd03bba78f7
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the LS1046A
architecture processor capable of support more than 32,000 CoreMark
performance. The FRWY-LS1046A board supports the LS1046A processor,
onboard DDR4 memory, multiple Gigabit Ethernet, USB3.0 and M2_Type_E
interfaces for Wi-Fi, FRWY-LS1046A-AC includes the Wi-Fi card.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I9a9680689e6f17bf4cc76fd5d1883eed6ace5149
The LS1046A reference design board (RDB) is a high-performance
computing, evaluation, and development platform that supports
the Layerscape LS1046A architecture processor.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Ib7a01b309e0b0acc7f38e22b138e9e181dff244a
The LS1046A is a cost-effective, power-efficient, and highly
integrated system-on-chip (SoC) design that extends the reach
of the NXP value-performance line of QorIQ communications
processors. Featuring power-efficient 64-bit Arm Cortex A72
cores with ECC-protected L1 and L2 cache memories for high
reliability, running up to 1.8 GHz.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: rocket <rod.dorris@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Change-Id: I208d9bf1702410463c2b2630d31d0cd4eb7e8837
These changes are required to accommodate 3MB for OP-TEE and this
is required for SP's part of optee
Added size macro's for better readability of the code
Moved uboot execution memory from CVM to DDR
Change-Id: I16657c6e336fe7c0fffdee1617d10af8a2c76732
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Signed-off-by: Arpita S.K <Arpita.S.K@arm.com>
diphda platform is now being renamed to corstone1000.
These changes are to replace all the instances and traces
of diphda corstone1000.
Change-Id: I330f3a112d232b99b4721b6bf0236253b068dbba
Signed-off-by: Arpita S.K <Arpita.S.K@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Add helper functions to generate event log for imx8mm
when MEASURED_BOOT=1.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: Ifc947d749055787fbda0b39170aa2eb8865b7802
The PIE compilation is used only for BL32, move the ENABLE_PIE to
sp_min-stm32mp1.mk file. Override PIE flags, as sp_min.mk file is
included after the flags are set in Makefile.
The BL2_IN_XIP_MEM was added for a feature not yet upstreamed.
It is then removed from platform.mk file.
Change-Id: If055e51e0f160f99cd4e4cf68ca718d4d693119c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
tamp_bkpr() returns a register address. So use uintptr_t instead of
uin32_t.
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Change-Id: I5eddfa525465313dadfec18d128248a968ba74e2
Add the SZ_* macros from 32 to 2G.
This allows removing some defines in raw NAND driver
and STM32MP1 boot device selection code.
Change-Id: I3c4d4959b0f43e785eeb37a43d03b2906b7fcfbc
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Signed-off-by: Arpita S.K <Arpita.S.K@arm.com>
Actually BL31_LIMIT is set to 0xffffffff but that doesn't work correctly
with bl31.ld since ". = ALIGN(((1) << (12)));" will try to fill aligned up
to 0x100000000 included, but the RAM size is 0xffffffff, so this leads to
this build error:
```
bl31.elf section `coherent_ram' will not fit in region `RAM'
/home/br-user/git/upstream/ci-tests/zynqmp_zcu102/host/bin/aarch64-buildroot-linux-uclibc-ld: region `RAM' overflowed by 1 byte
```
So let's move BR31_LIMIT to 0x100000000 giving 1 byte more room to fill RAM
up to the end.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Change-Id: Ic0edb8ed159e013f60598a9dd4f50adbf656b38d
Add board support for variant 2 of RD-N2 platform which is a four chip
variant with 4 cores on each chip. The "CSS_SGI_PLATFORM_VARIANT" value
is 2 for multi-chip variant. The "CSS_SGI_CHIP_COUNT_MACRO" can be in
the range [1, 4] for multi-chip variant.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I6412106e80e2f17704c796226c2ee9fe808705ba
Add support for the PSCI CPU_ON call to allow booting secondary CPU
cores. On cold boot they need to be booted with a special register
sequence. Also, the "boot remapper" needs to be configured to point to
the BL31_BASE, so the CPUs actually start executing BL31 after reset.
Change-Id: I406c508070ccb046bfdefd51554f12e1db671fd4
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Wasim Khan
Madhukar Pappireddy
Manish Pandey
Pali Rohár
Rex-BC Chen
Uwe Kleine-König
Joanna Farley
Olivier Deprez
Manish V Badarkhe
Juan Pablo Conde
Rohit Mathew
Imre Kis
Michal Simek
Boon Khai Ng
Sieu Mun Tang
Abdul Halim, Muhammad Hadi Asyrafi
Venkatesh Yadav Abbarapu
Yann Gautier
Ravi Patel
Ronak Jain
Nava kishore Manne
Rajan Vaja
Yann Gautier
Sandrine Bailleux
jason-ch chen
Tamas Ban
Siew Chin Lim
Jiafei Pan
Federico Recanati
Tony K Nadackal
Satish Kumar
Emekcan Aras
Arpita S.K
Vishnu Banavath
Ying-Chun Liu (PaulLiu)
Nicolas Toromanoff
Giulio Benetti
Aditya Angadi
Stephan Gerhold