For rk3399, the L2ACTLR[14] is 0 by default, as ACE CCI-500 doesn't
support WriteEvict. and you will hit the condition L2ACTLR[3] with 0,
as the Evict transactions should propagate to CCI-500 since it has
snoop filters.
Maybe this erratum applies to all Cortex-A53 cores so far, especially
if RK3399's A53 is a r0p4. we should enable it to avoid data corruption,
Change-Id: Ib86933f1fc84f8919c8e43dac41af60fd0c3ce2f
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
A recent commit 030567e6f5 added U()/ULL()
macro to TF constants. This has caused some signed-unsigned comparison
warnings / errors in the TF static analysis.
This patch addresses these issues by migrating impacted variables from
signed ints to unsigned ints and vice verse where applicable.
Change-Id: I4b4c739a3fa64aaf13b69ad1702c66ec79247e53
Signed-off-by: David Cunado <david.cunado@arm.com>
On Juno AArch32, the L2 cache may contain garbage after the warm reset
from AArch64 to AArch32. This is all fine until the MMU is configured
and the data caches enabled. To avoid fetching stale data from the L2
unified cache, invalidate it before the warm reset to AArch32 state.
Change-Id: I7d27e810692c02c3e83c9f31de67f6bae59a960a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Before BL2 loads the SCP ram firmware, `SCP_BOOT_CFG_ADDR` specifies
the primary core. After the SCP ram firmware has started executing,
`SCP_BOOT_CFG_ADDR` is modified. This is not normally an issue but
the Juno AArch32 boot flow is a special case. BL1 does a warm reset
into AArch32 and the core jumps to the `sp_min` entrypoint. This is
effectively a `RESET_TO_SP_MIN` configuration. `sp_min` has to be
able to determine the primary core and hence we need to restore
`SCP_BOOT_CFG_ADDR` to the cold boot value before `sp_min` runs.
This magically worked when booting on A53 because the core index was
zero and it just so happened to match with the new value in
`SCP_BOOT_CFG_ADDR`.
Change-Id: I105425c680cf6238948625c1d1017b01d3517c01
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
For some reason, HDCP key decrytion can't open source in ATF, so we
build it as hdcp.bin. Besides declare the handler for decrypting.
Change-Id: Ia67ff2442ab43cb3ee4875b3d59cc1608e854b4b
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Use TF_CFLAGS instead of CFLAGS, to allow CFLAGS to be overriden from
the make command line.
Change-Id: I3e5726c04bcd0176f232581b8be2c94413374ac7
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
These errata are only applicable to AArch64 state. See the errata notice
for more details:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.epm048406/index.html
Introduce the build options ERRATA_A53_835769 and ERRATA_A53_843419.
Enable both of them for Juno.
Apply the 835769 workaround as following:
* Compile with -mfix-cortex-a53-835769
* Link with --fix-cortex-a53-835769
Apply the 843419 workaround as following:
* Link with --fix-cortex-a53-843419
The erratum 843419 workaround can lead the linker to create new sections
suffixed with "*.stub*" and 4KB aligned. The erratum 835769 can lead the
linker to create new "*.stub" sections with no particular alignment.
Also add support for LDFLAGS_aarch32 and LDFLAGS_aarch64 in Makefile for
architecture-specific linker options.
Change-Id: Iab3337e338b7a0a16b0d102404d9db98c154f8f8
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
SPE is only supported in non-secure state. Accesses to SPE specific
registers from SEL1 will trap to EL3. During a world switch, before
`TTBR` is modified the SPE profiling buffers are drained. This is to
avoid a potential invalid memory access in SEL1.
SPE is architecturally specified only for AArch64.
Change-Id: I04a96427d9f9d586c331913d815fdc726855f6b0
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Currently, ROTPK_NOT_DEPLOYED flag is set in plat_get_rotpk_info().
It is up to users how to retrieve ROTPK if the ROT verification is
desired. This is not nice.
This commit improves plat_get_rotpk_info() implementation and automates
the ROTPK deployment. UniPhier platform has no ROTPK storage, so it
should be embedded in BL1/BL2, like ARM_ROTPK_LOCATION=devel_rsa case.
This makes sense because UniPhier platform implements its internal ROM
i.e. BL1 is used as updatable pseudo ROM.
Things work like this:
- ROT_KEY (default: $(BUILD_PLAT)/rot_key.pem) is created if missing.
Users can override ROT_KEY from the command line if they want to
use a specific ROT key.
- ROTPK_HASH is generated based on ROT_KEY.
- ROTPK_HASH is included by uniphier_rotpk.S and compiled into BL1/BL2.
- ROT_KEY is input to cert_create tool.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On ARM platforms before exiting from SP_MIN ensure that
the default console is switched to the runtime serial port.
Change-Id: I0ca0d42cc47e345d56179eac16aa3d6712767c9b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
With GCC 6.2 compiler, more C undefined behaviour is being flagged as
warnings, which result in build errors in ARM TF build.
This patch addresses issue caused by enums with values that exceed
maximum value for an int. For these cases the enum is converted to
a set of defines.
Change-Id: I5114164be10d86d5beef3ea1ed9be5863855144d
Signed-off-by: David Cunado <david.cunado@arm.com>
The patch fb7d32e588 migrated the CPU
libraries to have unique defines, prefixing them with the CPU name.
This patch migrates the hikey960 platform port to use the A53 specific
defines.
Change-Id: Id76f544b0b236bbd4974ab5ffa1203f073c20021
Signed-off-by: David Cunado <david.cunado@arm.com>
In CPU off callback function, the old code uses the function
hisi_test_pwrdn_allcores() to check if all CPUs in cluster have been
powered off and if it's valid then power off the whole cluster. But the
function hisi_test_pwrdn_allcores() only maintains the different power
states only for CPU suspend/resume flow, so it cannot return correct
states for CPU on/off flow.
This patch is to change use hisi_test_cpu_down() to check if all CPUs
have been powered off, so that can power off the whole cluster properly
when all CPUs in cluster have been hotplugged off.
Signed-off-by: Tao Wang <kevin.wangtao@hisilicon.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
The ARM_PLAT_MT bit enables the support for MT bit in
MPIDR format. This means that the level 0 affinity
represents the thread and CPU / Cluster levels are
at affinity level 1 and 2 respectively.
This was not catered for in the scpi 'css_scp_get_power_state, API.
Since the SCPI driver can only cater for single threaded CPUs,
this patch fixes the problem by catering for this shift by
effectively ignoring the Thread (level 0) affinity level.
Change-Id: If44f55c9fb2773c8d3f8a9bbcf5420a6f7409dfe
Signed-off-by: jagadeesh ujja <jagadeesh.ujja@arm.com>
Main fixes:
* Added explicit casts (e.g. 0U) to integers in order for them to be
compatible with whatever operation they're used in [Rule 10.1]
* Force operands of an operator to the same type category [Rule 10.4]
* Added curly braces ({}) around if/while statements in order to
make them compound [Rule 15.6]
* Added parentheses [Rule 12.1]
* Voided non C-library functions whose return types are not used [Rule 17.7]
Change-Id: I91404edec2e2194b1ce2672d2a3fc6a1f5bf41f1
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Main fixes:
* Include header file for function declarations [Rule 8.4]
* Move global object into function [Rule 8.9]
Change-Id: I1bc9f3f0ebd4ffc0b8444ac856cd97b0cb56bda4
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
Main fixes:
* Use int32_t replace int, use uint32_t replace unsign int [Rule 4.6]
* Added explicit casts (e.g. 0U) to integers in order for them to be
compatible with whatever operation they're used in [Rule 10.1]
* Force operands of an operator to the same type category [Rule 10.4]
* Fixed assert/if statements conditions to be essentially boolean [Rule 14.4]
* Added curly braces ({}) around if statements in order to
make them compound [Rule 15.6]
* Convert macros form headers to unsigned ints
Change-Id: I8051cc16499cece2039c9751bd347645f40f0901
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Main fixes:
* Added explicit casts (e.g. 0U) to integers in order for them to be
compatible with whatever operation they're used in [Rule 10.1]
* Convert object type to match the type of function parameters
[Rule 10.3]
* Added curly braces ({}) around if statements in order to
make them compound [Rule 15.6]
* Expressions resulting from the expansion of macro parameters
shall be enclosed in parentheses[Rule 20.7]
Change-Id: I5cf83caafcc1650b545ca731bf3eb8f0bfeb362b
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
Main fixes:
* Fixed if/while statement conditional to be essentially boolean [Rule 14.4]
* Added curly braces ({}) around if/for/while statements in order to
make them compound [Rule 15.6]
* Added explicit casts (e.g. 0U) to integers in order for them to be
compatible with whatever operation they're used in [Rule 10.1]
Change-Id: Ic72b248aeede6cf18bf85051188ea7b8fd8ae829
Signed-off-by: Anthony Zhou <anzhou@nvidia.com>
This patch moves the GPU reset state check, during VideoMem resize, to the
common SiP handler, to reduce code duplication.
Change-Id: I3818c5f104b809da83dc2a61d6a8149606f81c13
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch fixes the logic to check if the command written to the
MC_CLIENT_HOTRESET_CTRLx registers, was accepted by the hardware module.
Change-Id: If94fff9424555cb4688042eda17b4b20f4eb399a
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch adds explicit casts (U(x)) to integers in the tegra_def.h
headers, to make them compatible with whatever operation they're used
in [MISRA-C Rule 10.1]
Change-Id: Ic5fc611aad986a2c6e6e6f625e0753ab9b69eb02
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch makes all the defines in the CPU libraries unique,
by prefixing them with the CPU name.
NOTE: PLATFORMS USING THESE MACROS WILL HAVE TO UPDATE THEIR CODE
TO START USING THE UPDATED NAMES
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch enables the 'sign-compare' flag, to enable warning/errors
for comparisons between signed/unsigned variables. The warning has
been enabled for all the Tegra platforms, to start with.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Since the type of ADC value is always unsigned int, don't
need to check the value with negative value.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Initial commit for Socionext UniPhier SoC support. BL1, Bl2, and
BL31 are supported. Refer to docs/plat/socionext-uniphier.md for
more detais.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The 'impl' variable is guarded by the symbol DEBUG, but used in an INFO
level print statement. INFO is defined based on LOG_LEVEL. Hence, builds
would fail when
- DEBUG=0 && LOG_LEVEL>=LOG_LEVEL_INFO with a variable used but not defined
- DEBUG=1 && LOG_LEVEL<LOG_LEVEL_INFO with a variable defined but not used
Fixing this by guarding impl with the same condition that guards INFO.
FixesARM-software/tf-issues#490
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
unlike rk3399 and rk3368, there are some rockchip 64bit SOC
do not have CPUPD, and pmu_cpuson_entrypoint() is common
function for rockchip platform, so we need to check wakeup
cpu when resume.
Change-Id: I6313e8a9d7c16b03e033414f0cb281646c2159ff
Signed-off-by: Lin Huang <hl@rock-chips.com>
with PMU_PERILP_PD_EN bit enable, the soc will shutdown
cm0, crypto, dcf, imem(normal SRAM), dmac, bootrom, efuse_con,
spi, i2c, uart, saradc, tsadc when suspend, we have M0 code
need to run when suspend in normal SRAM, so we need to take
care of that.
Change-Id: I8c066637e5b81d4b1d53197450b9d592cbe00793
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
This moves the DRAM restore code to PMUSRAM. This is so that the
voltage domain that contains the SRAM that it was stored in before may
be turned off during system suspend.
Change-Id: Id761181a30caadd12f1ce061d1034f3159a76d28
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
This converts two functions to use for-loops. This saves a bit of
space to help moving DRAM resume code to PMUSRAM.
Change-Id: Ie6ca490cf50c2ec83335cf1845b337c3e8a47496
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
The removed if statement would make the same check that the for loop
it is in does to break out of the for loop, so it doesn't make any
sense to keep it there.
Change-Id: I819c29f9182e6de1fc47e418aed15ad38e8f9fa9
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
This removes the mmio_... function calls to set the multicast bit for
the PHY registers when overriding the write leveling values. These are
not needed since multicast is set by default when calling the
function, and it's also better not to leave the side effect of
disabling multicast when exiting the function.
Change-Id: I83e089a2a2d55268b3832f36724c3b2c4be81082
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
This removes the phy_dll_bypass_set function as it is unneeded. The
values that function sets are saved during suspend, so the proper
values will be restored on resume.
Change-Id: I17542206c56e639ce8cb6375233145167441d4e2
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
This removes the space allocation for the unused PHY register space.
For instance in PHY registers 0-127, only 0-90 are used, so don't save
the 91-127 registers. This saves about 1.6KB of space.
Change-Id: I0c9f6d9bed8f0c1f3b8b805dfb10cf0c06208919
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
the function pmu_cpuon_entrypoint() need to run in the pmusram,
we just copy bin file to pmusram before, now we add pmusram section
and link pmu_cpuon_entrypoint() to pmusram directly
Change-Id: Iae31e4c01c480c8e6f565a8f588332b478efdb16
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
The differential signal of DQS need keep low level
before gate training. It need enable RPULL and disable
PHY side ODT to ensure it when do gate training.
But it can not access the PHY registers to do it when
perform DFS.So the workaroud as below: It is ensure that
the PHY's read gate is landing somewhere in the incoming
DQS's pulses before it starts searching for pre-amble window.
It need get the rddqs_delay_ps to calculate the start point
of gate training for DFS.
Change-Id: I79eabcf4ec9a9c8f4539f68a51f22afba49c72fe
Signed-off-by: Lin Huang <hl@rock-chips.com>
Support BL31 on HiKey960 platform. Implement PSCI.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
BL2 loads MCU firmware & BL31 on hikey960 platform. The MCU firmware
is used to implement low power feature.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Support BL1 on HiKey960 platform. When recovery mode is detected,
BL1 loads NS BL1U that flushs images into UFS. When normal boot
mode is detected, BL1 loads BL2.
Fix for https://github.com/ARM-software/tf-issues/issues/486
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
This patch adds the memory map region for the SCMI payload memory
and maps the Juno core indices to SCMI power domains via the
`plat_css_core_pos_to_scmi_dmn_id_map` array.
Change-Id: I0d2bb2a719ff5b6a9d8e22e91e1625ab14453665
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds the SCMI driver for communicating with SCP. The power
domain management and system power management protocol of the SCMI
specification[1] is implemented in the driver. The SCP power management
abstraction layer for SCMI for CSS power management is also added.
A new buid option `CSS_USE_SCMI_DRIVER` is introduced to select SCMI
driver over SCPI.
[1] ARM System Control and Management Interface v1.0 (SCMI)
Document number: ARM DEN 0056A
Change-Id: I67265615a17e679a2afe810b9b0043711ba09dbb
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
ARM GIC-600 IP complies with ARM GICv3 architecture, but among others,
implements a power control register in the Redistributor frame. This
register must be programmed to mark the frame as powered on, before
accessing other registers in the frame. Rest of initialization sequence
remains the same.
The driver provides APIs for Redistributor power management, and
overrides those in the generic GICv3 driver. The driver data is shared
between generic GICv3 driver and that of GIC-600.
For FVP platform, the GIC-600 driver is chosen when FVP_USE_GIC_DRIVER
is set to FVP_GIC600. Also update user guide.
Change-Id: I321b2360728d69f6d4b0a747b2cfcc3fe5a20d67
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Both Cortex-A75 and Cortex-A55 CPUs use the ARM DynamIQ Shared Unit
(DSU). The power-down and power-up sequences are therefore mostly
managed in hardware, and required software operations are considerably
simpler.
Change-Id: I68b30e6e1ebe7c041d5e67f39c59f08575fc7ecc
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch is to enable CPU suspend/resume and system level's
suspend/resume; also enable system power off state.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The cluster 0 doesn't rely on PSCI to enable it; so enable CCI port
for cluster 0 in BL31 platform setup flow.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Fix for CPU topology so present the CPU core numbers for two clusters;
Base on this fixing, the PSCI can maintain correct power states.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Support BL31 and PSCI. Enable multiple cores in PSCI.
Change-Id: I66c39e1e9c4c45ac41a0142ed2070d79a3ac5ba3
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Dan Handley <dan.handley@arm.com>
BL2 is used to load BL31 and SCP_BL2. In HiKey platform, SCP_BL2
is the mcu firmware that is used to scale cpu frequency and switch
low power mode.
Change-Id: I1621aa65bea989fd125ee8502fd56ef72362bf97
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Dan Handley <dan.handley@arm.com>
Initialize regulators, pins and eMMC in BL1. Only SRAM could be used in BL1.
So BL2 will be loaded from eMMC into SRAM later.
Change-Id: I8e7ef82ffa29a3c647c9d2d2981e8759ee85d833
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Dan Handley <dan.handley@arm.com>
Since ARM_DRAM2_BASE is above the 32-bit limit, the condition
is always false. Wrap this condition in an ifndef to avoid
warnings during compilation.
Change-Id: Ideabb6c65de6c62474ed03eb29df4b049d5316be
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
This function was removed long ago. Remove remaining
pragma reference.
Change-Id: I66c556863d47dc17d2ffdc6c23aa524df6aade80
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
The default case is impossible to hit as the `power_level`
is already checked earlier. Avoids a clang warning.
Change-Id: I707463c843adc748ee9aa1d2313f9ab7dab3a8ab
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
This options enables an implementation of SHA-256 that has a smaller
code footprint (~1.6 KB less) but is also ~30% slower. For ARM
platforms, code size is currently considered more important than
execution speed in the mbed TLS crypto module.
Added a small note about this option to the documentation of the
authentication framework.
Change-Id: I4c0b221ea5d3466465261316ba07b627fa01b233
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The header tbbr_oid.h contains OIDs obtained by ARM Ltd.
so there is no good reason to use platform_oid.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Platforms aligned with TBBR are supposed to use their own OIDs, but
defining the same macros with different OIDs does not provide any
value (at least technically).
For easier use of TBBR, this commit allows platforms to reuse the OIDs
obtained by ARM Ltd. This will be useful for non-ARM vendors that
do not need their own extension fields in their certificate files.
The OIDs of ARM Ltd. have been moved to include/tools_share/tbbr_oid.h
Platforms can include <tbbr_oid.h> instead of <platform_oid.h> by
defining USE_TBBR_DEFS as 1. USE_TBBR_DEFS is 0 by default to keep the
backward compatibility.
For clarification, I inserted a blank line between headers from the
include/ directory (#include <...>) and ones from a local directory
(#include "..." ).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The commit abd2aba99e introduced a
regression to the AArch32 sp_min Juno build. This patch fixes that.
Change-Id: I4b141717684d6aee60c761ea17f23170aa6708c3
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Add support for firmware upgrade on AArch32.
This patch has been tested on the FVP models.
NOTE: Firmware upgrade on Juno AArch32 is not currently supported.
Change-Id: I1ca8078214eaf86b46463edd14740120af930aec
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Co-Authored-By: Yatharth Kochar <yatharth.kochar@arm.com>
This patch adds `TRUSTED_BOARD_BOOT` support for AArch32 mode.
To build this patch the "mbedtls/include/mbedtls/bignum.h"
needs to be modified to remove `#define MBEDTLS_HAVE_UDBL`
when `MBEDTLS_HAVE_INT32` is defined. This is a workaround
for "https://github.com/ARMmbed/mbedtls/issues/708"
NOTE: TBBR support on Juno AArch32 is not currently supported.
Change-Id: I86d80e30b9139adc4d9663f112801ece42deafcf
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>
Co-Authored-By: Yatharth Kochar <yatharth.kochar@arm.com>
A previous patch superseded the MBEDTLS_KEY_ALG. This patch updates
the ARM platforms to use the new TF_MBEDTLS_KEY_ALG define.
Change-Id: Ie0e1bc272e127e879ac58e7cfcbe268751d7688e
Signed-off-by: David Cunado <david.cunado@arm.com>
For SoCs T132 and T210, the header file 'platform_def.h' used to include
'tegra_def.h' and vice versa. This patch breaks this circular dependency
by making 'tegra_def.h' independent.
Change-Id: I45a00a84e6ab8b93d5e9242a9ff65f03e9102a96
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
We used to have the following circular dependency in the FVP platform
header files:
+-> arm_def.h ---> platform_def.h ---> fvp_def.h --+
|__________________________________________________|
This patch breaks it by not including 'arm_def.h' from 'fvp_def.h'.
Change-Id: I280d906559e3343dd38764029e77c0ea768b4fec
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
A new file added as part of arm-trusted-firmware#927 was missing the
SPDX license identifier - this patch adds the missing identifier.
Change-Id: Id1355f2bdca930b7e65bb54eff7e6c764ebb0d96
Signed-off-by: David Cunado <david.cunado@arm.com>
danh-arm
Caesar Wang
davidcunado-arm
Dimitris Papastamos
Ziyuan Xu
Douglas Raillard
Masahiro Yamada
Leo Yan
jagadeesh ujja
Haojian Zhuang
Anthony Zhou
Varun Wadekar
Soby Mathew
Soren Brinkmann
Lin Huang
Derek Basehore
Vincent Guittot
Jeenu Viswambharan
David Wang
Antonio Nino Diaz
Yatharth Kochar
tony.xie
Sandrine Bailleux