Define Qemu AArch32 implementation for some platform functions
(core position, secondary boot cores, crash console). These are
derived from the AArch64 implementation.
BL31 on Qemu is needed only for ARMv8 and later. On ARMv7, BL32 is
the first executable image after BL2.
Support SP_MIN and OP-TEE as BL32: create a sp_min make script target
in Qemu, define mapping for IMAGE_BL32
Minor fix Qemu return value type for plat_get_ns_image_entrypoint().
Qemu model for the Cortex-A15 does not support the virtualization
extension although the core expects it. To overcome the issue, Qemu
ARMv7 configuration set ARCH_SUPPORTS_VIRTUALIZATION to 0.
Add missing AArch32 assembly macro arm_print_gic_regs from ARM platform
used by the Qemu platform.
Qemu Cortex-A15 model integrates a single cluster with up to 4 cores.
Change-Id: I65b44399071d6f5aa40d5183be11422b9ee9ca15
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Looks like this is requirement in the pre-merge static analysis.
misra_violation: [Required] MISRA C-2012 Rule 7.2 violation:
Unsigned constants must be declared with U or u suffix.
Adding ULL as requested. I used ULL() macros for BL*_{BASE,LIMIT}
because they are referenced from linker scripts.
Requested-by: David Cunado <david.cunado@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the xlat region of the on-chip SRAM is always allocated
for all BL images.
The access to the on-chip SRAM is necessary for loading images from
a USB memory device (i.e. when updating firmware), so unneeded for
the usual boot procedure.
To avoid this waste, allocate the xlat region dynamically only for
BL2, and only when it is necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 247fc04351 ("uniphier: switch to BL2-AT-EL3 and remove BL1
support") accidentally changed the location of BL31 and BL32. The
new memory map overlaps with the audio DSP images, also gives impact
to OP-TEE. They are both out of control of ARM Trusted Firmware, so
not easy to change. This commit restores the image layout that was
originally used prior to the BL2-AT-EL3 migration.
Reported-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Allow to handle GZIP-compressed images by giving FIP_GZIP=1 from the
command line.
- Images are GZIP-compressed, then packed into FIP. If Trusted Board
Boot is enabled, certificates are generated based on the compressed
images.
- GZIP decompressor is linked into BL2 to decompress images at
run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the next commit, I will have more usecases to get struct image_info
from image ID. It is better to make a helper function at a different
layer. I do not need the current uniphier_image_descs_fixup() since
the code is small enough to be squashed into the caller side.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Just like bl2_, add pre/post image load handlers for BL1. No argument
is needed since BL2 is the only image loaded by BL1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are cases where we need to manipulate image information before
the load. For example, for decompressing data, we cannot load the
compressed images to their final destination. Instead, we need to
load them to the temporary buffer for the decompressor.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When we add a new callback, we need to duplicate fallbacks among
plat/common/{aarch32,aarch64}/platform_helpers.S This is tedious.
I created a new C file, then moved 3 functions:
plat_error_handler
bl2_plat_preload_setup
plat_try_next_boot_source
They are called from C, so I do not see a good reason to implement
them in assembly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the next commit, I need the image name in lowercase because
output files are generally named in lowercase.
Unfortunately, TOOL_ADD_IMG takes the first argument in uppercase
since we generally use uppercase Make variables.
make_helpers/build_macros.mk provides 'uppercase' macro to convert
a string into uppercase, but 'lowercase' does not exist. We can
implement it if we like, but it would be more straightforward to
change the argument of TOOL_ADD_IMG.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now FIP_ADD_IMG takes care of both fiptool and cert_create
symmetrically. Rename it so that it matches the behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The build system supports generating two FIP images, fip and fwu_fip.
Accordingly, we have similar build macros.
FIP_ADD_PAYLOAD <--> FWU_FIP_ADD_PAYLOAD
CERT_ADD_CMD_OPT <--> FWU_CERT_ADD_CMD_OPT
FIP_ADD_IMG <--> FWU_FIP_ADD_IMG
The duplicated code increases the maintenance burden. Also, the build
rule of BL2U looks clumsy - we want to call MAKE_BL to compile it from
source files, but we want to put it in fwu_fip. We can not do it in a
single macro call since the current MAKE_BL does not support fwu_fip.
To refactor those in a clean way is to support one more argument to
specify the FIP prefix. If it is empty, the images are targeted to
fip, whereas if the argument is "FWU_", targeted to fwu_fip.
The build macros prefixed with FWU_ go away.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Coverity scan done for the coreboot project found the issue:
Coverity (*** CID 1385418: Memory - illegal accesses (OVERRUN))
Coverity (*** CID 1385419: Memory - corruptions (OVERRUN))
Fix the Converity error issue with store_cru[] loop needs to be one
element bigger.
Fixes: ARM-software/tf-issues#544
Change-Id: I420f0a660b24baaa5fc5e78fca242cf750c9bbc7
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
This patch maps the devices in the first GB of the system address map
on the FVP into the S-EL1&0 translation regime when SPM support is
enabled. This grants the Secure Partition access to the devices in
this region, for example the memory-mapped Generic Timer device.
Change-Id: I3aeea65f859ecbe83efde2acee20c55500c451bc
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
`assert(e)` was used in place of `if (e) ERROR()` when sec_protect()
was ported from hikey fork so the logic should have been reversed.
Fixes: 3d5d9f5a ("hikey: configure the top 16MB of DRAM as secure")
Fixes: 52988b38 ("hikey: configure 4 MB of secure DRAM for OP-TEE
Secure Data Path")
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Victor Chong <victor.chong@linaro.org>
This disables the redistributor before either of the pwr_dm_suspend
functions are called. This is because the rdist save code in the
rk3399 rockchip_soc_sys_pwr_dm_suspend function requires that each
redistributor be disabled before saving state.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
UniPhier platform implements non-TF boot ROM. Prior to the BL2-AT-EL3
support, BL1 (worked as a pseudo ROM) was needed just for ensuring BL2
is entered at EL1-S. Now, this platform is able to avoid this waste.
Enable the BL2_AT_EL3 option, and remove BL1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The warm boot mailbox code is compiled if PROGRAMMABLE_RESET_ADDRESS
is disabled.
The warm boot mailbox is useless for UniPhier SoC family because BL1
is not the first image. The UniPhier platform implements non-TF ROM,
then BL1 works as a pseudo ROM, so it is never executed in the warm
boot.
The reset vector address is not actually programmable for UniPhier
platform, but it should not hurt to enable PROGRAMMABLE_RESET_ADDRESS
to disable the mailbox and remove pointless plat_get_my_entrypoint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Update the memory firewall configuration to reserve 4 MB of secure RAM
for use by the kernel and OP-TEE as the Secure Data Path pool.
Note that this address range (0x3E800000 - 0x3EC00000) falls in the
range already set aside by UEFI (which reserves the upper 32 MB of the
1GB DRAM for OP-TEE [1]) and was previously unused.
[1] https://github.com/96boards-hikey/edk2/blob/hikey/HisiPkg/HiKeyPkg/Library/HiKeyLib/HiKeyMem.c#L44
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Victor Chong <victor.chong@linaro.org>
DRAM region 0x3f000000 - 0x3fffffff is reserved for OP-TEE and should
therefore be accessible only from secure world.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Victor Chong <victor.chong@linaro.org>
We were looping for MAX_WAIT_COUNT in several places without any
delays, so this adds the delays to make those loops more predictable.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
The code was accidentally restoring the QOS on suspend and saving the
QOS on resume. This is the opposite of what we want.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
This brings ATF into line with the kernel on the timeout for power
domains turning on. We could actually timeout (when we shouldn't) on
resume when turning power domains on. The guaranteed maximum delay is
now 10ms.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
The `override ERROR_DEPRECATION = 1` setting in uniphier platform
makes deprecation of API difficult. Hence removing the same. This
flag should be specified on the command line if needed.
Change-Id: I8c82d8d13944e450a8cd636de3326137c04d7560
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Let bl1 and bl2 have the ability to load images from emmc instead of
dram (mmap).
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
When some interrupts are configured as group 0 in GICv2, these
interrupts trigger FIQ signal; this results in the Linux kernel panic
by reporting log: "Bad mode in FIQ handler detected on CPU0, code
0x00000000 -- Unknown/Uncategorized". Unfortunately from kernel side it
has no permission to read the GIC register for group 0 interrupts so we
have no chance to get to know which interrupt is configured as secure
interrupt and cause the kernel panic.
For upper reason, this commit enables FIQ exception handling for
SPD_none case. If the system has not enabled SPD the FIQ interrupt is
trapped into EL3 and the FIQ handler can report the interrupt number so
we can easily narrow down which FIQ introduce unexpected interrupt.
After enable SPD we can rely on SPD interrupt route model to handle FIQ.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
This patch changes all Rockchip platforms to use the new
MULTI_CONSOLE_API. The platform-specific plat_crash_console
implementations are removed so that the platform can use the ones from
the common platform code instead.
Also change the registers used in plat_crash_print_regs. The existing
use of x16 and x17 has always been illegal, since those registers are
reserved for use by the linker as a temporary scratch registers in
intra-procedure-call veneers and can never be expected to maintain their
values across a function call.
Change-Id: I8249424150be8d5543ed4af93b56756795a5288f
Signed-off-by: Julius Werner <jwerner@chromium.org>
This patch changes all Rockchip platforms to initialize the serial
console with information supplied by coreboot rather than hardcoded
base address and divisor values if BL31 is run on top of coreboot.
Moving the BL2-to-BL31 parameter parsing as early as possible to ensure
that the console is available for all following code.
Also update the Rockchip platform to use MULTI_CONSOLE_API.
Change-Id: I670d350fa2f8b8133539f91ac14977ab47db60d9
Signed-off-by: Julius Werner <jwerner@chromium.org>
This patch expands the weak stubs for the plat_crash_console_xxx
functions in common platform code to use the new console API for crash
output. This should make crash console output "just work" for most cases
without the need for the platform to explicitly set up a crash console.
For cases where the normal console framework doesn't work (e.g. very
early crashes, before the platform can register any consoles), platforms
are still able to override the functions just like before.
This feature requires the MULTI_CONSOLE_API compile-time flag to work.
For builds which don't have it set, this patch has no practical effect.
Change-Id: I80dd161cb43f9db59a0bad2dae33c6560cfac584
Signed-off-by: Julius Werner <jwerner@chromium.org>
This patch modifies the makefiles to avoid the definition
of BL1_SOURCES and BL2_SOURCES in the tbbr makefiles, and
it lets to the platform makefiles to define them if they
actually need these images. In the case of BL2_AT_EL3
BL1 will not be needed usually because the Boot ROM will
jump directly to BL2.
Change-Id: Ib6845a260633a22a646088629bcd7387fe35dcf9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.
The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:
--data cluster0.cpu0=bl2.bin@0x4001000
-C cluster0.cpu0.RVBAR=0x4001000
These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.
Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This patch enables BL2 to execute at the highest exception level
without any dependancy on TF BL1. This enables platforms which already
have a non-TF Boot ROM to directly load and execute BL2 and subsequent BL
stages without need for BL1. This is not currently possible because
BL2 executes at S-EL1 and cannot jump straight to EL3.
Change-Id: Ief1efca4598560b1b8c8e61fbe26d1f44e929d69
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
At early time, the CPU CA73 retention state has been supported on
Hikey960. Later we found the system has the hang issue and for
resolving this issue Hisilicon released new MCU firmware, but
unfortunately the new MCU firmware has side effect and results in the
CA73 CPU cannot really enter retention state and roll back to WFI state.
After discussion we cannot see the possibility to enable CA73 retention
state anymore on Hikey960, based on this conclusion we should remove
this state supporting from ARM-TF and roll back to WFI state only. We
will commit one patch to remove CA73 CPU retention state in kernel DT
binding as well.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
This reverts commit fdae60b6ba.
The commit fdae60b6ba changed the
parameter encoding for the hikey960. However that implies a DT change
in the kernel side. After submitting the DT change for upstreaming,
the backward compatibility issue and the interface change raise some
concerns from the Linux community about the issues related to kernel <->
ATF alignment. There is no way to detect a mis-alignment of those
without a deep knowledge of the ATF and the kernel. Furthermore, the
failing calls to PSCI in the idle path (because of bad parameters), will
lead to busy looping, implying: thermal issues and extra energy
consumption.
In regard of the Linux community concerns, the potential issues when the
ATF and the kernel are not aligned, it is preferable to revert the
commit.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Kevin Wang <jean.wangtao@linaro.org>
Co-authored-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Use zynqmp_ipi APIs to access IPI registers in pm_service.
As the zynqmp_ipi APIs doesn't cover IPI buffers, the pm_ipi
in pm_service will still directly access the IPI buffers.
Signed-off-by: Wendy Liang <jliang@xilinx.com>
Previously, ZynqMP IPI in ATF is only for ZynqMP PM,
This patch is to have a ZynqMP IPI implementation to handle
both ZynqMP PM IPI requirement and IPI mailbox service requirement
which will be introduced next.
We control IPI agents registers access but not IPI buffers access in
this implementation. Each IPI mailbox user will directly access the
IPI buffers.
Signed-off-by: Wendy Liang <jliang@xilinx.com>
It is not necessary to read data from stdin. The input file name
is ripped off by -n option, anyway. I still use the redirect for
the output to specify the output file name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To allow BL31 to grow in SRAM, move TSP in TZC secured DRAM
by default.
Increase the BL31 max limit by one page.
Change-Id: Idd3479be02f0f9bafac2f275376d7db0c2015431
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
The current IO block buffer overlaps with BL2 image location.
So, BL2 may corrupt itself.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.
Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch overhauls the console API to allow for multiple console
instances of different drivers that are active at the same time. Instead
of binding to well-known function names (like console_core_init),
consoles now provide a register function (e.g. console_16550_register())
that will hook them into the list of active consoles. All console
operations will be dispatched to all consoles currently in the list.
The new API will be selected by the build-time option MULTI_CONSOLE_API,
which defaults to ${ERROR_DEPRECATED} for now. The old console API code
will be retained to stay backwards-compatible to older platforms, but
should no longer be used for any newly added platforms and can hopefully
be removed at some point in the future.
The new console API is intended to be used for both normal (bootup) and
crash use cases, freeing platforms of the need to set up the crash
console separately. Consoles can be individually configured to be active
active at boot (until first handoff to EL2), at runtime (after first
handoff to EL2), and/or after a crash. Console drivers should set a sane
default upon registration that can be overridden with the
console_set_scope() call. Code to hook up the crash reporting mechanism
to this framework will be added with a later patch.
This patch only affects AArch64, but the new API could easily be ported
to AArch32 as well if desired.
Change-Id: I35c5aa2cb3f719cfddd15565eb13c7cde4162549
Signed-off-by: Julius Werner <jwerner@chromium.org>
The current Rockchip platform code retains the "common" default panic
handler which simply hangs the system (until the watchdog kicks in, if
enabled). This is usually not a great user experience.
This patch implements a Rockchip-specific panic handler that calls the
platform's reboot implementation to reset the system.
Change-Id: I4cbe09c48f1b3f86ebdfc0108c186565f9ffc119
Signed-off-by: Julius Werner <jwerner@chromium.org>
The security properties of some IP blocks are configured to secure mode
after reset. This means these IP blocks can only be accessed by cpus
in secure state by default. These should be configured correclty as needed.
Signed-off-by: y00241285 <yyangwei.yangwei@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
After returning from SYSTEM_SUSPEND state, BL31 reconfigures the
TrustZone Controller during the boot sequence. If BL31 is placed in
TZC-secured DRAM, it will try to change the permissions of the memory it
is being executed from, causing an exception.
The solution is to disable SYSTEM_SUSPEND when the Trusted Firmware has
been compiled with ``ARM_BL31_IN_DRAM=1``.
Change-Id: I96dc50decaacd469327c6b591d07964726e58db4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Common code mustn't include ARM platforms headers.
Change-Id: Ib6e4f5a77c2d095e6e8c3ad89c89cb1959cd3043
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
ARM Power State Coordination Interface (ARM DEN 0022D) chapter
6.5 "Recommended StateID Encoding" defines the state ID which can be
used by platforms. The recommended power states can be presented by
below values; and it divides into three fields, every field has 4 bits
to present power states corresponding to core level, cluster level and
system level.
0: Run
1: Standby
2: Retention
3: Powerdown
This commit changes to use upper recommended power states definition on
Hikey960; and changes the power state validate function to check the
power state passed from kernel side.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
This patch allows non-secure bus masters to access TZC region0 as well
as the EL3 Payload itself.
Change-Id: I7e44f2673a2992920d41503fb4c57bd7fb30747a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This includes the stdint header to declare the various types used within
the file, preventing build errors with recent GCC versions.
Change-Id: I9e7e92bb31deb58d4ff2732067dd88b53124bcc9
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This port can be compiled to boot an AArch64 or AArch32 payload with the
build option `RPI3_BL33_AARCH32`.
Note: This is not a secure port of the Trusted Firmware. This port is
only meant to be a reference implementation to experiment with an
inexpensive board in real hardware.
Change-Id: Ide58114299289bf765ef1366199eb05c46f81903
Co-authored-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Pre-v8.2 platforms such as the Juno platform does not have
the Scalable Vector Extensions implemented and so the build
option ENABLE_SVE is set to zero.
This has a minor performance improvement with no functional
impact.
Change-Id: Ib072735db7a0247406f8b60e325b7e28b1e04ad1
Signed-off-by: David Cunado <david.cunado@arm.com>
The bl2_early_platform_setup() and bl2_platform_setup() were
redefined for Juno AArch32 eventhough CSS platform layer had
same definition for them. The CSS definitions definitions were
previously restricted to EL3_PAYLOAD_BASE builds and this is now
modified to include the Juno AArch32 builds as well thus
allowing us to remove the duplicate definitions in Juno platform
layer.
Change-Id: Ibd1d8c1428cc1d51ac0ba90f19f5208ff3278ab5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch fixes a couple of issues for AArch32 builds on ARM reference
platforms :
1. The arm_def.h previously defined the same BL32_BASE value for AArch64 and
AArch32 build. Since BL31 is not present in AArch32 mode, this meant that
the BL31 memory is empty when built for AArch32. Hence this patch allocates
BL32 to the memory region occupied by BL31 for AArch32 builds.
As a side-effect of this change, the ARM_TSP_RAM_LOCATION macro cannot
be used to control the load address of BL32 in AArch32 mode which was
never the intention of the macro anyway.
2. A static assert is added to sp_min linker script to check that the progbits
are within the bounds expected when overlaid with other images.
3. Fix specifying `SPD` when building Juno for AArch32 mode. Due to the quirks
involved when building Juno for AArch32 mode, the build option SPD needed to
specifed. This patch corrects this and also updates the documentation in the
user-guide.
4. Exclude BL31 from the build and FIP when building Juno for AArch32 mode. As
a result the previous assumption that BL31 must be always present is removed
and the certificates for BL31 is only generated if `NEED_BL31` is defined.
Change-Id: I1c39bbc0abd2be8fbe9f2dea2e9cb4e3e3e436a8
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
When defining different sections in linker scripts it is needed to align
them to multiples of the page size. In most linker scripts this is done
by aligning to the hardcoded value 4096 instead of PAGE_SIZE.
This may be confusing when taking a look at all the codebase, as 4096
is used in some parts that aren't meant to be a multiple of the page
size.
Change-Id: I36c6f461c7782437a58d13d37ec8b822a1663ec1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Set alignment size to 512B so finally we can get fip.bin with 512B
alignment. This can avoid stuck issue for 'fastboot' downloading
if USB driver uses DMA for data transferring.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Set alignment size to 512B so finally we can get fip.bin with 512B
alignment. This can avoid stuck issue for 'fastboot' downloading if
USB driver uses DMA for data transferring.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Factor out SPE operations in a separate file. Use the publish
subscribe framework to drain the SPE buffers before entering secure
world. Additionally, enable SPE before entering normal world.
A side effect of this change is that the profiling buffers are now
only drained when a transition from normal world to secure world
happens. Previously they were drained also on return from secure
world, which is unnecessary as SPE is not supported in S-EL1.
Change-Id: I17582c689b4b525770dbb6db098b3a0b5777b70a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Support SDEI on ARM platforms using frameworks implemented in earlier
patches by defining and exporting SDEI events: this patch defines the
standard event 0, and a handful of shared and private dynamic events.
Change-Id: I9d3d92a92cff646b8cc55eabda78e140deaa24e1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Define number of priority bits, and allocate priority levels for SDEI.
Change-Id: Ib6bb6c5c09397f7caef950c4caed5a737b3d4112
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
davidcunado-arm
Etienne Carriere
Masahiro Yamada
Caesar Wang
Dimitris Papastamos
Sandrine Bailleux
Victor Chong
Derek Basehore
Peter Griffin
Jerome Forissier
Soby Mathew
Leo Yan
Julius Werner
Roberto Vargas
Kaihua Zhong
Wendy Liang
Jeenu Viswambharan
Haojian Zhuang
Jiancheng Xue
Antonio Nino Diaz
Paul Kocialkowski