Enable the SCMI protocol support in SynQuacer platform.
Aside from power domain, system power and apcore management protocol,
this commit adds the vendor specific protocol(0x80).
This vendor specific protocol is used to get the dram mapping information
from SCP.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
The comment suggests checking version numbers and
a checksum but there doesn't seem to be any usable
data for either of these.
For example, fip_toc_header_t doesn't contain any
version information and neither does fip_toc_entry_t.
As the function name "is_valid_header" suggests, this
function is not concerned with checksumming any of
the table of contents entries.
Change-Id: I8673ae5dd37793771760169f26b2f55c15fbf587
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
This TODO was added five years ago so I assume that there is not
going to be a shutdown API added after all.
Change-Id: If0f4e2066454df773bd9bf41ed65d3a10248a2d3
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
There are some issues with synopsys MMC driver:
- CMD8 should not expect data (for SD)
- ACMD51 should expect data (Send SCR for SD)
- dw_prepare should not dictate size to be MMC_BLOCK_SIZE, block size is
now handled in the dw_prepare function
- after the CMD completes, when doing dw_read, we need to invalidate cache
and wait for the data transfer to complete
- Need to set FIFO threshold, otherwise DMA might never get the interrupt
to read or write
Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>
STM32MP1 SDMMC device voltage is 3.3V. We should then precise the 2 ranges
3.2 to 3.3V and 3.3 to 3.4V in ocr_voltage field.
Change-Id: I88e479f8f16bfe608a7808eace0df3fdec48deab
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Some bugs in MMC stack needs to be fixed:
- scr cannot be local as this will cause cache issue when invalidating
after the read DMA transfer is completed
- ACMD41 needs to send voltage information in initialization, otherwise the
command is a query, thus will not initialize the controller
- when checking device state, retry until the retries counter goes to zero
before failing
Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>
Configure the GPIO5 09 pin as input on the ULCB board by default,
since the pin is routed on the expansion connector and not connected
to anything by default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add support for the M3W 3.0 SoC and synchronize the upstream ATF with
Renesas downstream ATF release v2.0.1.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Due to the shared Mbed TLS heap optimisation introduced in 6d01a463,
common code files were depending on Mbed TLS specific headers. This
dependency is now removed by moving the default, unoptimised heap
implementation inside the Mbed TLS specific files.
Change-Id: I11ea3eb4474f0d9b6cb79a2afd73a51a4a9b8994
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
Fix some typos and clarify some sentences.
Change-Id: Id276d1ced9a991b4eddc5c47ad9a825e6b29ef74
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This commit improves the SDHost driver for RPi3 as following:
* Unblock MMC_CMD(17). Using MMC_CMD(17) is more efficient on
block reading.
* In some low probability that SEND_OP_COND might results CRC7
error. We can consider that the command runs correctly. We don't
need to retry this command so removing the code for retry.
* Using MMC_BUS_WIDTH_1 as MMC default value to improve the stability.
* Increase the clock to 50Mhz in data mode to speed up the io.
* Change the pull resistors configuration to gain more stability.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
STM32MP1 chip embeds a dual Cortex-A7 and a Cortex-M4.
The support for Cortex-M4 clocks is added when configuring the clock tree.
Some minimal security features to allow communications between A7 and M4
are also added.
Change-Id: I60417e244a476f60a2758f4969700b2684056665
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Cortex a5 doesnt support hardware division such as sdiv and udiv commands.
This commit adds a software division function in assembly as well as include
appropriate files for software divison.
The software division algorithm is a modified version obtained from:
http://www.keil.com/support/man/docs/armasm/armasm_dom1359731155623.htm
Change-Id: Ib405a330da5f1cea1e68e07e7b520edeef9e2652
Signed-off-by: Usama Arif <usama.arif@arm.com>
Remove useless private structure in function prototypes.
Add a reference counter on clocks.
Prepare for future secured/shared/non-secured clocks.
Change-Id: I3dbed81721da5ceff5e10b2c4155b1e340c036ee
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
This change makes the platform to panic in case of peripheral reset
resource malfunction.
Change-Id: I17eb9cb045b78a4e5142a8c33b744e84992d732a
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
PWR, RCC, DDRPHYC & DDRCTRL addresses can be retrieved from device tree.
Platform asserts the value read from the DT are the SoC addresses.
Change-Id: I43f0890b51918a30c87ac067d3780ab27a0f59de
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
Create a new file stm32mp_clkfunc.c to put functions that could be common
between several platforms.
Change-Id: Ica915c796b162b2345056b33328acc05035a242c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Regulator configuration at boot takes more information from DT.
I2C configuration from DT is done in I2C driver.
I2C driver manages more transfer modes.
The min voltage of buck1 should also be increased to 1.2V,
else the platform does not boot.
Heavily modifies stm32_i2c.c since many functions move inside the source
file to remove redundant declarations.
Change-Id: I0bee5d776cf3ff15e687427cd6abc06ab237d025
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
Remove the previously use function: get_timer, and use new functions
timeout_init_us and timeout_elapsed.
Change-Id: I4e95b123648bff7ca91e40462a2a3ae24cfe1697
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>
Include all RCC, clocks and reset headers from stm32mp1_def.h
which if exported to the firmware through platform_def.h.
The same dependency removal is done in common code as well.
Some useless includes are also removed in stm32_sdmmc2 driver.
Change-Id: I731ea5775c3fdb7f7b0c388b93923ed5e84b8d3f
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Mainly remove suffix 1 from prefix stm32mp1 in several macros and functions
that can be used in drivers shared by different platforms.
Change-Id: I2295c44f5b1edac7e80a93c0e8dfd671b36e88e7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Some parts of code could be shared with platform derivatives,
or new platforms.
A new folder plat/st/common is created to put common parts.
stm32mp_common.h is a common API aggregate.
Remove some casts where applicable.
Fix some types where applicable.
Remove also some platform includes that are already in stm32mp1_def.h.
Change-Id: I46d763c8d9e15732d1ee7383207fd58206d7f583
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
This is to add simple MBR partition entry support. This will read all four
MBR partition into the partition list, and the partition type will be saved
in the list.name[0] entry.
Signed-off-by: Loh Tien Hock <tien.hock.loh@intel.com>
This commit migrates to MULTI_CONSOLE_API for IMX Warp7 board.
We also rename the functions in imx_uart driver to more specific one.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
The Generic Timer is an optional extension to an ARMv7-A implementation.
The generic delay timer can be used from any architecture supported by
the Trusted Firmware. In ARMv7 it is needed to check that this feature
is present. In ARMv8 it is always present.
Change-Id: Ib7e8ec13ffbb2f64445d4ee48ed00f26e34b79b7
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Previously the GICv3 redistributor probe function
(gicv3_rdistif_base_addrs_probe()) asserted that the number of
per-CPU redistributor interfaces expected to be probed by the
platform is equal to the number exported by the redistributor
frame. This is a problem in case the number of CPUs in the
platform is less than the number of redistributor interfaces
in the frame. Hence this patch removes the assertion check
and allows probe for fewer redistributor interfaces as required
by the platform.
Change-Id: I3449763a3ad70817224442cbe184d001030c9874
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This commit adds SDHost driver for RaspberryPi3. SDHost driver uses the
GPIO driver to connect the SDCard and SDHost. By using this driver it is
able to read/write raw blocks on SDCard.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Clean up the NOTICE() and FATAL_MSG() outputs, so that they contain
proper newlines and BL2 prefixes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Method cpld_reset_cpu of bl31 is called from the Linux kernel and uses
GPIO6, GPIO2 pins as SPI bus lines to control the CPLD device. But in the
kernel GPIO6_8 pin are initialized to work in interrupt mode instead of
the input/output mode. This leads to the fact that the SPI bus becomes
non-functional. In this patch we switch the GPIO6_8 pin back to the
input-output mode.
Signed-off-by: Sergii Boryshchenko <sergii.boryshchenko@globallogic.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The ATF code fails to build with PMIC_ROHM_BD9571=0, add the missing
function into the PWRC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This commit adds GPIO driver for RaspberryPi3. The GPIO driver for RPi3
also provides the way to do pinmux selections.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
The BSEC (Boot and Security and OTP control) is intended to control an OTP
(one time programmable) fuse box, used for on-chip non-volatile storage
for device configuration and security parameters.
Change-Id: I38c44684c7b9c6a1f24ec0ae3fe99cec481d5a51
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Change fdt_check_status function to fdt_get_status.
Update GPIO defines.
Move some functions in gpio driver, instead of dt helper file.
Add GPIO bank helper functions.
Use only one status field in dt_node_info structure including both status
and secure status.
Change-Id: I34f93408dd4aac16ae722f564bc3f7d6ae978cf4
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Reword some traces.
Use uintptr_t where required.
Reduce scope of variables.
Improve io_stm32image algo.
Complete some IP registers definitions.
Add failure on supported DDR (stm32mp1_ddr_init()).
Fix cache flush on cache disable (stm32mp1_ddr_setup).
Change-Id: Ie02fa71e02b9d69abc807fd5b7df233e5be6668c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Change-Id: I4a1b281925e0a3a1e2a34b3e363537e4a7f13823
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
The drivers are also updated to reflect the changes.
Set RCC as non-secure.
Change-Id: I568fa1f418355830ad1d4d1cdcdb910fb362231b
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This is the correct name of the IP.
Rename stm32mp1_pmic files to stm32mp_pmic.
Change-Id: I238a7d1f9a1d099daf7788dc9ebbd3146ba2f15f
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The driver could be used for other devices than PMIC.
Change-Id: I4569e7c0028e52e1ff2fe9d38f11de11e95d1897
Signed-off-by: Yann Gautier <yann.gautier@st.com>
In patch 93768644, ret will be MMC_STATE_TRAN (=4), which is a valid value.
We shouldn't exit the function in that case, but only if ret is < 0.
Change-Id: I776693fe847b6b45190af028f12d2e724ca46399
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Corrects typos in core code, documentation files, drivers, Arm
platforms and services.
None of the corrections affect code; changes are limited to comments
and other documentation.
Change-Id: I5c1027b06ef149864f315ccc0ea473e2a16bfd1d
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Use the SCIF SCFSR:TEND bit to check that all data were transmitted by
the SCIF and that there are no more valid data to transmit in the FIFO.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Synchronize the R-Car DDR-B driver, used on R-Car H3/M3W/M3N,
with Renesas ATF release 2.0.0 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Run Linux kernel checkpatch on the DDR-A init code to clean it up:
$ checkpatch.pl --fix --fix-inplace -f drivers/staging/renesas/rcar/ddr/ddr_a/*
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Call the function only from architecture setup and at the end of
suspend cycle instead of calling it all over the place.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Instead, only platform_def.h is included.
The required files to be included are added in stm32mp1_def.h.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Running TF-A 2.0 and later seems to cause a regression on HiKey 620.
NOTICE: BL2: v2.0(release):v2.0
NOTICE: BL2: Built : 17:41:23, Dec 17 2018
NOTICE: acpu_dvfs_set_freq: set acpu freq success!ERROR: CMD1 failed after 100 retries
ERROR: BL2: Failed to load image (-5)
The reason seems to be that during emmc enumeration when BL2 sends the command
OCR_SECTOR_MODE | OCR_VDD_MIN_2V7 | OCR_VDD_MIN_1V7
it for some reason takes some more time to get a reply. So a delay with
mdelay(1), seems to not be enough any longer and therefore we increase it to
mdelay(10) instead which makes the device boot as expected again.
Signed-off-by: Joakim Bech <joakim.bech@linaro.org>
Now that we have switched to using the stack in MULTI_CONSOLE_API
framework functions and have factored all code involved in crash
reporting out into a separate file, there's really no reason to keep the
main framework code in assembly anymore. This patch rewrites it in C
which allows us to have a single implementation across aarch32/64 and
should be much easier to maintain going forward.
Change-Id: I6c85a01e89a79e8b233f3f8bee812f0dbd026221
Signed-off-by: Julius Werner <jwerner@chromium.org>
This patch makes the build system link the console framework code by
default, like it already does with other common libraries (e.g. cache
helpers). This should not make a difference in practice since TF is
linked with --gc-sections, so the linker will garbage collect all
functions and data that are not referenced by any other code. Thus, if a
platform doesn't want to include console code for size reasons and
doesn't make any references to console functions, the code will not be
included in the final binary.
To avoid compatibility issues with older platform ports, only make this
change for the MULTI_CONSOLE_API.
Change-Id: I153a9dbe680d57aadb860d1c829759ba701130d3
Signed-off-by: Julius Werner <jwerner@chromium.org>
Crash reporting via the default consoles registered by MULTI_CONSOLE_API
has been broken since commit d35cc34 (Console: Use callee-saved
registers), which was introduced to allow console drivers written in C.
It's not really possible with the current crash reporting framework to
support console drivers in C, however we should make sure that the
existing assembly drivers that do support crash reporting continue to
work through the MULTI_CONSOLE_API.
This patch fixes the problem by creating custom console_putc() and
console_flush() implementations for the crash reporting case that do not
use the stack. Platforms that want to use this feature will have to link
plat/common/aarch64/crash_console_helpers.S explicitly.
Also update the documentation to better reflect the new reality (of this
being an option rather than the expected default for most platforms).
Change-Id: Id0c761e5e2fddaf25c277bc7b8ab603946ca73cb
Signed-off-by: Julius Werner <jwerner@chromium.org>
This driver can be compiled in release builds, but GCC generates warnings
for some comparisons and that prevents the firmware from being built in
debug builds.
Change-Id: Ic52e1b4a11896ecf086864fbe2b5bfc143ec9b1b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
- Update CPU frequency on AP807 to 2GHz for SAR 0x0.
- Increase AVS to 0.88V for 2GHz clock
Change-Id: Ic945b682ab2f8543e34294bfc56c3eae2c5e0c8e
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
In Armada 8K DB boards, PCIe initialization can be executed only once
because PCIe reset performed during chip power on and it cannot be
executed via GPIO later.
This means that power on can be executed only once, when it's called
from the bootloader.
Power on:
Read bit 21 of the mode, it marks if the caller is
the bootloader or the Linux Kernel.
Power off:
Check if the comphy was already configured to PCIe, if yes,
check if the caller is bootloader, if both conditions are true
(PCIe mode and called by Linux) - skip the power-off.
In addition, fix incorrect documentation describing mode fields -
PCIe width is 3 bits, not 2.
NOTE: with this patch, please use LK4.14.76 (LK4.4.120 may not work
with it).
Change-Id: I4b929011f97a0a1869a51ba378687e78b3eca4ff
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
EXT_CSD command needs to access data from eMMC device. Add the
operation of polling eMMC device status. Make sure the command is
finished.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
ARM CoreLink DMC-620 Dynamic Memory Controller includes a TZC controller
to setup secure or non-secure regions of DRAM memory. The TZC controller
allows to setup upto eight such regions of memory in DRAM. This driver
provides helper functions to setup the TZC controller within DMC-620.
Change-Id: Iee7692417c2080052bdb7b1c2873a024bc5d1d10
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Migrate Marvell platforms from legacy console API to
multi-console API.
Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Now that MULTI_CONSOLE_API is enabled for the STM32MP1 platform,
we can remove the non MULTI_CONSOLE_API parts in the driver.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
These issues wer found by sparse:
drivers/st/clk/stm32mp1_clk.c:1524:19:
warning: incorrect type in assignment (different base types)
expected restricted fdt32_t const [usertype] *pkcs_cell
got unsigned int const [usertype] *
plat/st/stm32mp1/plat_image_load.c:13:6:
warning: symbol 'plat_flush_next_bl_params' was not declared.
Should it be static?
plat/st/stm32mp1/plat_image_load.c:21:16:
warning: symbol 'plat_get_bl_image_load_info' was not declared.
Should it be static?
plat/st/stm32mp1/plat_image_load.c:29:13:
warning: symbol 'plat_get_next_bl_params' was not declared.
Should it be static?
plat/st/stm32mp1/bl2_io_storage.c:40:10:
warning: symbol 'block_buffer' was not declared. Should it be static?
Signed-off-by: Yann Gautier <yann.gautier@st.com>
cppcheck:
[drivers/partition/gpt.c:19] -> [drivers/partition/gpt.c:19]:
(warning) Either the condition 'str_in!=((void*)0)' is redundant
or there is possible null pointer dereference: name.
sparse:
drivers/partition/gpt.c:39:9:
warning: Using plain integer as NULL pointer
Signed-off-by: Yann Gautier <yann.gautier@st.com>
All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.
The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.
The exceptions are files that are imported from other projects:
- CryptoCell driver
- dt-bindings folders
- zlib headers
Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This function was needed at the time where we didn't have the
compiler_rt lib. An AArch32-specific variant was provided to handle
the 64-bit shift operation in 32-bit. This is no longer needed.
Change-Id: Ibab709a95e3a723ae2eeaddf873dba70ff2012b3
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
It isn't possible to build this driver without adding this define.
Change-Id: Iba2ced411cd8ce438787871fa01b414d32b9aa42
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
It has only been tested with a system clock of 24 MHz.
It has only been implemented for the multi console API.
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The definitions FAIL_CONTROL_*_SHIFT were incorrect, they have been
fixed.
The types tzc_region_attributes_t and tzc_action_t have been removed and
replaced by unsigned int because it is not allowed to do logical
operations on enums.
Also, fix some address definitions in arm_def.h.
Change-Id: Id37941d76883f9fe5045a5f0a4224c133c504d8b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Add support for Marvell Armada-3700 COMPHY driver
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
The "Reduced Serial Bus" is an Allwinner specific bus, bearing many
similarities with I2C. It sports a much higher bus frequency, though,
(typically 3 MHz) and requires much less handholding for the typical
task of manipulating slave registers (fire-and-forget).
On most A64 boards this bus is used to connect the PMIC to the SoC.
This driver provides basic primitives to read and write slave registers,
it will be later used by the PMIC code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The `finish_console_register` macro is used by the multi console
framework to register the `console_t` driver callbacks. It relied
on weak references to the `ldr` instruction to populate 0 to the
callback in case the driver has not defined the appropriate
function. Use of `ldr` instruction to load absolute address to a
reference makes the binary position dependant. These instructions
should be replaced with adrp/adr instruction for position independant
executable(PIE). But adrp/adr instructions don't work well with weak
references as described in GNU ld bugzilla issue 22589.
This patch defines a new version of `finish_console_register` macro
which can spcify which driver callbacks are valid and deprecates the
old one. If any of the argument is not specified, then the macro
populates 0 for that callback. Hence the functionality of the previous
deprecated macro is preserved. The USE_FINISH_CONSOLE_REG_2 define
is used to select the new variant of the macro and will be removed
once the deprecated variant is removed.
All the upstream console drivers have been migrated to use the new
macro in this patch.
NOTE: Platforms be aware that the new variant of the
`finish_console_register` should be used and the old variant is
deprecated.
Change-Id: Ia6a67aaf2aa3ba93932992d683587bbd0ad25259
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Some of COMPHY parameters depends on the hw connection between the SoC
and the PHY, which can vary on different boards e.g. due to different
wires length. Define the "porting layer" with some defaults
parameters. It ease updating static values which needs to be updated due
to board differences, which are now grouped in one place.
Example porting layer for a8k-db is under:
plat/marvell/a8k/a80x0/board/phy-porting-layer.h
If for some boards parameters are not defined (missing
phy-porting-layer.h), the default values are used
(drivers/marvell/comphy/phy-default-porting-layer.h)
and the following compilation warning is show:
"Using default comphy params - you may need to suit them to your board".
The common COMPHY driver code is extracted in order to be shared with
future COMPHY driver for A3700 SoC platforms
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reference code:
==============
rar_gen3: IPL and Secure Monitor Rev1.0.22
https://github.com/renesas-rcar/arm-trusted-firmware [rcar_gen3]
Author: Takuya Sakata <takuya.sakata.wz@bp.renesas.com>
Date: Thu Aug 30 21:26:41 2018 +0900
Update IPL and Secure Monitor Rev1.0.22
General Information:
===================
This port has been tested on the Salvator-X Soc_id r8a7795 revision
ES1.1 (uses an SPD).
Build Tested:
-------------
ATFW_OPT="LSI=H3 RCAR_DRAM_SPLIT=1 RCAR_LOSSY_ENABLE=1"
MBEDTLS_DIR=$mbedtls
$ make clean bl2 bl31 rcar PLAT=rcar ${ATFW_OPT} SPD=opteed
Other dependencies:
------------------
* mbed_tls:
git@github.com:ARMmbed/mbedtls.git [devel]
Merge: 68dbc94 f34a4c1
Author: Simon Butcher <simon.butcher@arm.com>
Date: Thu Aug 30 00:57:28 2018 +0100
* optee_os:
https://github.com/BayLibre/optee_os
Until it gets merged into OP-TEE, the port requires Renesas' Trusted
Environment with a modification to support power management.
Author: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Date: Thu Aug 30 16:49:49 2018 +0200
plat-rcar: cpu-suspend: handle the power level
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
* u-boot:
The port has beent tested using mainline uboot.
Author: Fabio Estevam <festevam@gmail.com>
Date: Tue Sep 4 10:23:12 2018 -0300
*linux:
The port has beent tested using mainline kernel.
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Sep 16 11:52:37 2018 -0700
Linux 4.19-rc4
Overview
---------
BOOTROM starts the cpu at EL3; In this port BL2 will therefore be entered
at this exception level (the Renesas' ATF reference tree [1] resets into
EL1 before entering BL2 - see its bl2.ld.S)
BL2 initializes DDR (and i2c to talk to the PMIC on some platforms)
before determining the boot reason (cold or warm).
During suspend all CPUs are switched off and the DDR is put in
backup mode (some kind of self-refresh mode). This means that BL2 is
always entered in a cold boot scenario.
Once BL2 boots, it determines the boot reason, writes it to shared
memory (BOOT_KIND_BASE) together with the BL31 parameters
(PARAMS_BASE) and jumps to BL31.
To all effects, BL31 is as if it is being entered in reset mode since
it still needs to initialize the rest of the cores; this is the reason
behind using direct shared memory access to BOOT_KIND_BASE and
PARAMS_BASE instead of using registers to get to those locations (see
el3_common_macros.S and bl31_entrypoint.S for the RESET_TO_BL31 use
case).
Depending on the boot reason BL31 initializes the rest of the cores:
in case of suspend, it uses a MBOX memory region to recover the
program counters.
[1] https://github.com/renesas-rcar/arm-trusted-firmware
Tests
-----
* cpuidle
-------
enable kernel's cpuidle arm_idle driver and boot
* system suspend
--------------
$ cat suspend.sh
#!/bin/bash
i2cset -f -y 7 0x30 0x20 0x0F
read -p "Switch off SW23 and press return " foo
echo mem > /sys/power/state
* cpu hotplug:
------------
$ cat offline.sh
#!/bin/bash
nbr=$1
echo 0 > /sys/devices/system/cpu/cpu$nbr/online
printf "ONLINE: " && cat /sys/devices/system/cpu/online
printf "OFFLINE: " && cat /sys/devices/system/cpu/offline
$ cat online.sh
#!/bin/bash
nbr=$1
echo 1 > /sys/devices/system/cpu/cpu$nbr/online
printf "ONLINE: " && cat /sys/devices/system/cpu/online
printf "OFFLINE: " && cat /sys/devices/system/cpu/offline
Signed-off-by: ldts <jramirez@baylibre.com>
Whereas the GPT table is read with io_block, the binaries to be loaded
(e.g. BL33) cannot use it, as it is not suitable to read them block by
block, or the boot time would be very bad.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This IO is required to read binaries with STM32 header.
This header is added with the stm32image tool.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This driver is for the STMicroelectronics sdmmc2 IP
which is in STM32MP1 SoC.
It uses the MMC framework, and can address either eMMC or SD-card.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The comments with the prototypes of the register functions of the
console drivers are incorrect. The arguments are wrong. This patch fixes
them.
Change-Id: I38c4b481ee69e840780111c42f03c0752eb6315c
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
commit 97d5db8c5c reverts an update to the
MMC layer that accompanied the original submission of this MMC driver this
is the right-thing-to-do in terms of the MMC spec.
Unfortunately the reversion also breaks this driver. The issue is the i.MX
controller doesn't want MMC_RSP_48 set for MMC_RESPONSE_R2.
The appropriate place to place that constraint is obviously in
drivers/imx/usdhc/imx_usdhc.c not in the shared MMC codebase. This patch
restores the logic the i.MX controller requires without breaking it for
everyone else.
Fixes: 97d5db8c5c
Fixes: 2a82a9c95f
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Jun Nie <jun.nie@linaro.org>
This way it can be reused by other platforms if needed.
Note that this driver is designed to work with the Versatile Express NOR
flash of Juno and FVP. In said platforms, the memory is organized as an
interleaved memory of two chips with a 16 bit word.
Any platform that wishes to reuse it with a different configuration will
need to modify the driver so that it is more generic.
Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Mark the GICv3, CCI and CCN code only used in Bl31 initialization
with __init to be reclaimed once no longer needed.
Change-Id: I3d77f36758450d9d1d87ecc60bc1c63fe4082667
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
Respect official response type and update response to follow
official specification.
All the MMC_RESPONSE_R(_x) are replaced with each corresponding define.
Partly revert 2a82a9c95f for dw_mmc.c:
Responses R1, R1B and R5 have CRC.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
It is still a placeholder, but now it is registered correctly by the
macro finish_console_register.
Change-Id: Ic78c966d9be606cbc1a53cec43ead23b32963afe
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The Poplar is broken on eMMC initialization because of commit
2a82a9c95f ("drivers: emmc: dw_mmc: Add response flag into response ID
definition"). It changes the driver behavior on response type handling
in dw_send_cmd(), because MMC_RESPONSE_R(2) and MMC_RESPONSE_R2 are
different things. MMC core is still sending the former while we already
changed to check the latter in dw_mmc driver.
This patch fixes R2 response type in MMC core code. It's the same
thing as what commit 94522ff7f6 ("drivers: mmc: Fix R3 response type
definition") does for R3 response.
With this fix, Poplar is back to work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Allow AArch32 to use the multi console driver by adding the
required functions
Change-Id: I9e69f18965f320074cf75442d6b0de891aef7936
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
The old driver is now in deprecated_console.S, in a similar way to the
AArch64 driver.
Change-Id: Ib57209c322576c451d466d7406a94adbf01ab8fd
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner 64-bit SoCs all use the Mentor Graphics MI2CV I2C controller
core, with inverted clear quirk.
Add a glue driver for this.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The I2C controller on Allwinner SoCs after A31 has a inverted interrupt
clear flag, which needs to be written 1 (rather than 0 on Marvell SoCs
and old Allwinner SoCs) to clear.
Add such a quirk to mi2cv driver common code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which
is also used by Allwinner.
As Mentor Graphics allows a lot of customization, the MI2CV in the two
SoC families are not compatible, and driver modifications are needed.
Extract the common code to a MI2CV driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The I2C controller found in Marvell A8K SoCs (and some older SoCs) mux
status and baudrate registers into the same address, however, it's a
vendor customization, and the original IP core by Mentor Graphics uses
two different addresses for the two registers.
Use anonymous union in the driver, in order to ease code sharing for
other SoC vendors that use this IP core (Allwinner SoCs that are newly
introduced to mainline ATF use this core).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Add USDHC driver to support boot EMMC. Only initialization
and single/multiple block read are tested.
[bod: fixed checkpatch.pl complaints]
[bod: changed name to imx_usdhc for namespace consistency]
[bod: squashed antecedent fixes into this one patch]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Add missing response type for SWITCH command and STOP_TRANSMISSION
so that controller can be configured accordingly.
[bod: ported this change from Jun's eMMC patches to the MMC driver]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
The R3 response type definition should be (1 << 0). Make sure we define the
expected response code in the appropriate fashion.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Add response flag into ID definition so that driver does not
need to handle it again.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Add delay timer API so that it can be called by delay timer
layer and used as delay timer globally.
[bod: changed name from imx_delay_timer -> imx_gpt ]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
The Mbed TLS drivers, in order to work, need a heap for internal usage.
This heap, instead of being directly referenced by the drivers, now it
is being accessed indirectly through a pointer. Also, the heap, instead
of being part of the drivers, now it is being received through the
plat_get_mbedtls_heap() function. This function requests a heap from the
current BL image which utilises the Mbed TLS drivers.
Those changes create the opportunity for the Mbed TLS heap to be shared
among different images, thus saving memory. A default heap
implementation is provided but it can be overridden by a platform
specific, optimised implemenetation.
Change-Id: I286a1f10097a9cdcbcd312201eea576c18d157fa
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
It turned out that resetting the RTC time register is not
necessary during initial configuration. Safely remove it
from the sequence.
Change-Id: Id2b9c7db44a8c8dbe88a7f8a21695b72a7fd78ee
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
This patch introduces new helper routines that allow
configuring the individual IRQs to be edge/level-triggered
via GICD_ICFGR registers. This is helpful to modify
the default configuration of the non-secure GIC SPI's, which
are all set during initialization to be level-sensitive.
Change-Id: I23deb4a0381691a686a3cda52405aa1dfd5e56f2
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Use PF instead of PP post-fix, since it is referring to "Phase Final"
(only G3 related register had correct spelling for relevant bit).
Change-Id: Ia5a9c9c78b74b15f7f8adde2c3ef4784c513da2c
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
The biggest comphy index can be equal to 6 so there is no need to use
uint64_t for storing it.
Change-Id: I14c2b68e51678a560815963c72aed0c37068f926
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Add simple driver which allows to configure the memory controller trust
zones. It is responsible for opening mc trustzone window, with
appropriate base address, size and attributes.
Example of usage in upcoming commits.
Change-Id: I8bea17754d31451b305040ee7de331fb8db0c63f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Rename a8k_common.h to armada_common.h to keep the same header
name across all other Marvell Armada platforms.
This is especially useful since various Marvell platforms may
use common platform files and share the driver modules.
Change-Id: I7262105201123d54ccddef9aad4097518f1e38ef
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
This patch does two main things
- It implements the crash console UART init in assembly, as a
hard-coded 115200 8N1 assumed from the 24 MHz clock.
If the clock setup code has not run yet, this code can't work but,
setting up clocks and clock-gates is way out of scope for this type of
recovery function.
- It adds code to write a character out of the NXP UART without using any
stack-based operations when doing so.
- Provides support for crash console in DCE or DTE mode.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
- Adds a simple register read/write abstraction to cut-down on the
amount of typing and text required to access UART registers in this driver.
- Adds a console getc() callback.
- Adds a console putc() callback, translating '\n' to '\r' + '\n'.
- Initializes the MXC UART, take a crude method of calculating the
BAUD rate generator. The UART clock-gates must have been enabled prior
to launching the UART init code.
Special care needs to be taken to ensure the UBIR is initialized before the
UBMR and we need to ensure that UCR2.SRST comes good before trying to
program other registers associated with the UART.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
tf_printf and tf_snprintf are now called printf and snprintf, so the
code needs to be updated.
Change-Id: Iffeee97afcd6328c4c2d30830d4923b964682d71
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This allows the console drivers to be implemented in C
Change-Id: Ibac859c4bcef0e92a0dcacc6b58ac19bc69b8342
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
The CCI500 TRM explicitily requires completion of the write
operation before the read operation, and it is not guaranteed
by dmb but it is dsb.
Change-Id: Ieeaa0d1a4b8fcb87108dea9b6de03d9c8a150829
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Because of -Werror, this causes a build error.
Change-Id: I37a8c4bbfe3f2ced5e17981a2814985919ad483b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Migrate dw_mmc driver from emmc framework to mmc framework. The
emmc framework will be abandoned.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
It should set buswidth and speed of mmc controller before accessing
mmc.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
DMA is always used in mmc driver. So the buffer address should
always follow the DMA limitation.
There're same requirement in mmc_read_blocks()/mmc_write_blocks()
on parameter buf. Since parameter buf comes from io_block driver,
it's already handled in io_block driver.
At here, just make the minimum address alignment on 16 chars.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
mmc_read_blocks()/mmc_write_blocks() derived from io_block_ops_t
type. It means that lba param should be integer type, not
unsigned integer type.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Sending CMD8 before CMD1 just causes to fetch data failure in eMMC.
Check whether it's eMMC first. If it's eMMC, send CMD1 command instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Functions provided by stdio.h such as printf and sprintf are available
in the codebase, but they add a lot of code to the final image if they
are used:
- AArch64: ~4KB
- AArch32: ~2KB in T32, ~3KB in A32
tf_printf and tf_snprintf are a lot more simple, but it is preferable
to use them when possible because they are also used in common code.
Change-Id: Id09fd2b486198fe3d79276e2c27931595b7ba60e
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
We had exit but we didn't have atexit, and we were calling panic and
tf_printf from exit, which generated a dependency from exit to them.
Having atexit allows to set a different function pointer in every image.
Change-Id: I95b9556d680d96249ed3b14da159b6f417da7661
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Mbebtls include paths are controlled by the user using the variable
MBEDTLS_DIR and they are out of the TF source tree. Since these
includes have a different origin it is better to move them to a
different variable.
This change makes easier for the romlib Makefile to parse the include
paths.
Change-Id: I3e4c99300f1012bc7f88c6b9f5bc0ec1f7b5aa8d
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
TF Makefile was linking all the objects files generated for the
Mbed TLS library instead of creating a static library that could be
used in the linking stage.
Change-Id: I8e4cd843ef56033c9d3faeee71601d110b7e4c12
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
When a platform enables its caches before it initializes the
GICC/GICR interface then explicit cache maintenance is not
needed. Remove these here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The DDR driver is under dual license, BSD and GPLv2.
The configuration parameters are taken from device tree.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
If a PMIC companion chip is present on board, it has to be configured
for regulators supplies.
This check is done with board DT configuration.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
The management of pinctrl nodes of device tree is also added.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
The clock driver is under dual license, BSD and GPLv2.
The clock driver uses device tree, so a minimal support for this is added.
The required files for driver and DTS files are in include/dt-bindings/.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
STM32MP1 is a microprocessor designed by STMicroelectronics,
based on a dual Arm Cortex-A7.
It is an Armv7-A platform, using dedicated code from TF-A.
STM32MP1 uses BL2 compiled with BL2_AT_EL3.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>
The functions cci_enable_snoop_dvm_reqs and cci_disable_snoop_dvm_reqs write
in the SNOOP_CTRL_REGISTER of the slave interface and it polls the status
register to be sure that the operation is finished before leaving the
functions. If the write in SNOOP_CTRL_REGISTER is reordered after the first
read in the status register then these functions can finish before
enabling/disabling snoops and DVM messages.
The CCI500 TRM specifies:
Wait for the completion of the write to the Snoop Control Register
before testing the change_pending bit.
Change-Id: Idc7685963f412be1c16bcd3c6e3cca826e2fdf38
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Remove assert on buffer address equal zero.
Marvell uses address 0x0 for loading BL33,
so this check is irrelevant and breaks the
debug builds on Marvell platforms.
Change-Id: Ie56a51138e2e4ddd8986dd7036797dc2d8b10125
Signed-off-by: Haim Boot <hayim@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/54589
Add i2c driver for A8K SoC family.
Change-Id: I5932b2fce286d84fc3ad5a74c4c456001faa3196
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add COMPHY driver for usage in a runtime service.
Change-Id: I6fb42d0a099496d5699ee24684ae2b93ed35770b
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add thermal driver for A8K SoC family.
The termal unit data is used by Marvell DRAM initialization
code for optimizing the memory controller configuration
Change-Id: Iad92689fa6e4224a89d872e9aa015393abd9cf73
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add LLC (L3) cache management drivers for Marvell SoCs
AP806, AP807 and AP810
Change-Id: Ic70710f9bc5b6b48395d62212df7011e2fbb5894
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add ModularChip and MCI drivers for A8K SoC family.
ModularChip drivers include support for the internal building
blocks of Marvell ARMADA SoCs - APN806, APN807 and CP110
Change-Id: I9559343788fa2e5eb47e6384a4a7d47408787c02
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add address decoding unit drivers for Marvell SoCs.
Address decoding flow and address translation units chart
are located at docs/marvell/misc/mvebu-a8k-addr-map.txt
Change-Id: Id6ce311fa1f4f112df3adfac5d20449f495f71ed
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
This change is largely based on existing eMMC framework by Haojian Zhuang
(@hzhuang1).
The MMC framework supports both eMMC and SD card devices. It was
written as a new framework since breaking few eMMC framework APIs.
At card probe and after the reset to idle command (CMD0), a Send
Interface Condition Command is sent (CMD8) to distinguish between
eMMC and SD card devices. eMMC devices go through the same
sequence as in the former eMMC framework. Else the framework
uses commands dedicated to SD-cards for init or frequency switch.
A structure is created to share info with the driver. It stores:
- the MMC type (eMMC, SD or SD HC)
- the device size
- the max frequency supported by the device
- the block size: 512 for eMMC and SD-HC and read from CSD
structure for older SD-cards
Restriction to align buffers on block size has been removed.
Cache maintenance was removed and is expected to be done in the platform
or device driver.
The MMC framework includes some MISRA compliance coding style
maybe not yet ported in the existing eMMC framework.
FixesARM-software/tf-issues#597
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Platform can define MAX_NUM_FIP_DEVICES in platform_def.h
to define the number of FIP io devices.
The FIP driver doesn't support muliple open file.
So only one single file can be open at a time across
multiple FIP devices.
For any FIP device, an image should be loaded
fully before moving on to the next image.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
To build with the new release, we pick couple of more files from mbedTLS
library.
Change-Id: I77dfe5723284cb26d4e5c717fb0e6f6dd803cb6b
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
RFC4122 defines that fields are stored in network order (big endian),
but TF-A stores them in machine order (little endian by default in TF-A).
We cannot change the future UUIDs that are already generated, but we can store
all the bytes using arrays and modify fiptool to generate the UUIDs with
the correct byte order.
Change-Id: I97be2d3168d91f4dee7ccfafc533ea55ff33e46f
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Use a _ prefix for Macro arguments to prevent that argument from
hiding variables of the same name in the outer scope
Rule 5.3: An identifier declared in an inner scope shall not
hide an identifier declared in an outer scope
Fixed For:
make LOG_LEVEL=50 PLAT=fvp
Change-Id: I67b6b05cbad4aeca65ce52981b4679b340604708
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
Rule 5.1: External identifiers shall be distinct
Some of the identifier names in the GICv3 driver were so long that the
first 31 characters were identical. This patch shortens these names to
make sure they are different.
Fixed for:
LOG_LEVEL=50 PLAT=fvp
Change-Id: Iecd551e3a015d144716b87b42c83dd3ab8c34d90
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
On TI platforms the UART is disabled by default and must be explicitly
enabled using the MDR1 register.
NOTE: The original definition of
http://www.ti.com/lit/ds/symlink/pc16550d.pdf has no MDR register, but
many TI SoCs implementing 16550 do have a quirky MDR register
implemented. So, this should be enabled with TI_16550_MDR_QUIRK
NOTE: In such implementation, the CSR register does not exist.
Signed-off-by: Benjamin Fair <b-fair@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
This patch implements support for adding dynamic configurations for
BL31 (soc_fw_config), BL32 (tos_fw_config) and BL33 (nt_fw_config). The
necessary cert tool support and changes to default chain of trust are made
for these configs.
Change-Id: I25f266277b5b5501a196d2f2f79639d838794518
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
In 'console_set_scope' and when registering a console, field 'flags' of
'console_t' is assigned a 32-bit value. However, when it is actually
used, the functions perform 64-bit reads to access its value. This patch
changes all 64-bit reads to 32-bit reads.
Change-Id: I181349371409e60065335f078857946fa3c32dc1
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
In the multi console driver, allowing to register the same console more
than once may result in an infinte loop when putc is called.
If, for example, a boot message is trying to be printed, but the
consoles in the loop in the linked list are runtime consoles, putc will
iterate forever looking for a console that can print boot messages (or
a NULL pointer that will never come).
This loop in the linked list can occur after restoring the system from a
system suspend. The boot console is registered during the cold boot in
BL31, but the runtime console is registered even in the warm boot path.
Consoles are always added to the start of the linked list when they are
registered, so this it what should happen if they were actually
different structures:
console_list -> NULL
console_list -> BOOT -> NULL
console_list -> RUNTIME -> BOOT -> NULL
console_list -> RUNTIME -> RUNTIME -> BOOT -> NULL
In practice, the two runtime consoles are the same one, so they create
this loop:
console_list -> RUNTIME -. X -> BOOT -> NULL
^ |
`----'
This patch adds an assertion to detect this problem. The assertion will
fail whenever the same structure tries to be registered while being on
the list.
In order to assert this, console_is_registered() has been implemented.
It returns 1 if the specified console is registered, 0 if not.
Change-Id: I922485e743775ca9bd1af9cbd491ddd360526a6d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Masahisa Kojima
Paul Beesley
Tien Hock, Loh
Yann Gautier
Dimitris Papastamos
Antonio Niño Díaz
Marek Vasut
John Tsichritzis
Ying-Chun Liu (PaulLiu)
Usama Arif
Soby Mathew
Sergii Boryshchenko
Florian La Roche
Joel Hutton
Joakim Bech
Pankaj Gupta
Julius Werner
Christine Gharzuzi
Igal Liberman
Grzegorz Jaszczyk
Peng Fan
Haojian Zhuang
Vijayenthiran Subramaniam
Konstantin Porotchkin
Alexei Colin
Sandrine Bailleux
ldts
Andre Przywara
Jorge Ramirez-Ortiz
Bryan O'Donoghue
Daniel Boulby
Shawn Guo
Sathees Balya
Icenowy Zheng
Jun Nie
Marcin Wojtas
Andrew F. Davis
Roberto Vargas
danh-arm
Ruchika Gupta
Jeenu Viswambharan
Benjamin Fair