This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.
The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.
Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch implements support for adding dynamic configurations for
BL31 (soc_fw_config), BL32 (tos_fw_config) and BL33 (nt_fw_config). The
necessary cert tool support and changes to default chain of trust are made
for these configs.
Change-Id: I25f266277b5b5501a196d2f2f79639d838794518
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.
The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.
Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch allows platforms to dynamically disable authentication of
images during cold boot. This capability is controlled via the
DYN_DISABLE_AUTH build flag and is only meant for development
purposes.
Change-Id: Ia3df8f898824319bb76d5cc855b5ad6c3d227260
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
In 'console_set_scope' and when registering a console, field 'flags' of
'console_t' is assigned a 32-bit value. However, when it is actually
used, the functions perform 64-bit reads to access its value. This patch
changes all 64-bit reads to 32-bit reads.
Change-Id: I181349371409e60065335f078857946fa3c32dc1
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
This reverts commit 2f18aa1fa3.
It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.
Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
SGI-575's NSRAM is neither in the same place nor the same size as Juno's.
Change-Id: Id6d692e9c7e9c1360014bb525eda966ebe29c823
Signed-off-by: Chris Kay <chris.kay@arm.com>
The bounds check in ARM_CASSERT_MMAP does not take into account the
array sentinel in plat_arm_mmap. This commit fixes this, and adds an
additional check to ensure the number of entries in the array is
within the bounds of PLAT_ARM_MMAP_ENTRIES.
Change-Id: Ie6df10c0aa0890d62826bc3224ad7b3e36fd53e2
Signed-off-by: Chris Kay <chris.kay@arm.com>
There are three calls to mmap_add_region() that always occur in
arm_setup_page_tables(), and two further calls based on whether coherent
memory is enabled, and whether SPM is enabled in BL31.
This commit adapts the ARM_BL_REGIONS definition to match the number of
calls made inside arm_setup_page_tables() so that the MAX_MMAP_REGIONS
is realigned with what is actually occurring.
Change-Id: I7adc05951abccf2cbd5c86280eb874911e6a1566
Signed-off-by: Chris Kay <chris.kay@arm.com>
The old API is deprecated and will eventually be removed.
Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.
The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.
Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.
The size of BL31 has been increased in builds with SPM.
Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
In the multi console driver, allowing to register the same console more
than once may result in an infinte loop when putc is called.
If, for example, a boot message is trying to be printed, but the
consoles in the loop in the linked list are runtime consoles, putc will
iterate forever looking for a console that can print boot messages (or
a NULL pointer that will never come).
This loop in the linked list can occur after restoring the system from a
system suspend. The boot console is registered during the cold boot in
BL31, but the runtime console is registered even in the warm boot path.
Consoles are always added to the start of the linked list when they are
registered, so this it what should happen if they were actually
different structures:
console_list -> NULL
console_list -> BOOT -> NULL
console_list -> RUNTIME -> BOOT -> NULL
console_list -> RUNTIME -> RUNTIME -> BOOT -> NULL
In practice, the two runtime consoles are the same one, so they create
this loop:
console_list -> RUNTIME -. X -> BOOT -> NULL
^ |
`----'
This patch adds an assertion to detect this problem. The assertion will
fail whenever the same structure tries to be registered while being on
the list.
In order to assert this, console_is_registered() has been implemented.
It returns 1 if the specified console is registered, 0 if not.
Change-Id: I922485e743775ca9bd1af9cbd491ddd360526a6d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
When TF is compiled for aarch32 MAX_VIRT_ADDR_SPACE_SIZE is 2^32 in some cases,
which makes the test (size) <= MAX_VIRT_ADDR_SPACE_SIZE a tautology because
uintptr_t is a 32 bit value. The cast remove the warning for clang.
Change-Id: I1345f3400f8fbbe4ffd3caa990a90e7ba593dba5
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
- Assign 0x10 for RAS exceptions on ARM platforms, and install
EHF priority descriptor.
- Call the common RAS initialisation from ARM BL31 setup.
- Add empty definitions for platform error records and RAS interrupts.
Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The ARMv8.4 RAS extensions introduce architectural support for software
to inject faults into the system in order to test fault-handling
software. This patch introduces the build option FAULT_HANDLING_SUPPORT
to allow for lower ELs to use registers in the Standard Error Record to
inject fault. The build option RAS_EXTENSIONS must also be enabled along
with fault injection.
This feature is intended for testing purposes only, and is advisable to
keep disabled for production images.
Change-Id: I6f7a4454b15aec098f9505a10eb188c2f928f7ea
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
EHF currently allows for registering interrupt handlers for a defined
priority ranges. This is primarily targeted at various EL3 dispatchers
to own ranges of secure interrupt priorities in order to delegate
execution to lower ELs.
The RAS support added by earlier patches necessitates registering
handlers based on interrupt number so that error handling agents shall
receive and handle specific Error Recovery or Fault Handling interrupts
at EL3.
This patch introduces a macro, RAS_INTERRUPTS() to declare an array of
interrupt numbers and handlers. Error handling agents can use this macro
to register handlers for individual RAS interrupts. The array is
expected to be sorted in the increasing order of interrupt numbers.
As part of RAS initialisation, the list of all RAS interrupts are sorted
based on their ID so that, given an interrupt, its handler can be looked
up with a simple binary search.
For an error handling agent that wants to handle a RAS interrupt,
platform must:
- Define PLAT_RAS_PRI to be the priority of all RAS exceptions.
- Enumerate interrupts to have the GIC driver program individual EL3
interrupts to the required priority range. This is required by EHF
even before this patch.
Documentation to follow.
Change-Id: I9471e4887ff541f8a7a63309e9cd8f771f76aeda
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Previous patches added frameworks for handling RAS errors. This patch
introduces features that the platform can use to enumerate and iterate
RAS nodes:
- The REGISTER_RAS_NODES() can be used to expose an array of
ras_node_info_t structures. Each ras_node_info_t describes a RAS
node, along with handlers for probing the node for error, and if
did record an error, another handler to handle it.
- The macro for_each_ras_node() can be used to iterate over the
registered RAS nodes, probe for, and handle any errors.
The common platform EA handler has been amended using error handling
primitives introduced by both this and previous patches.
Change-Id: I2e13f65a88357bc48cd97d608db6c541fad73853
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The ARMv8 RAS Extensions introduced Standard Error Records which are a
set of standard registers through which:
- Platform can configure RAS node policy; e.g., notification
mechanism;
- RAS nodes can record and expose error information for error handling
agents.
Standard Error Records can either be accessed via. memory-mapped
or System registers. This patch adds helper functions to access
registers and fields within an error record.
Change-Id: I6594ba799f4a1789d7b1e45b3e17fd40e7e0ba5c
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
RAS extensions are mandatory for ARMv8.2 CPUs, but are also optional
extensions to base ARMv8.0 architecture.
This patch adds build system support to enable RAS features in ARM
Trusted Firmware. A boolean build option RAS_EXTENSION is introduced for
this.
With RAS_EXTENSION, an Exception Synchronization Barrier (ESB) is
inserted at all EL3 vector entry and exit. ESBs will synchronize pending
external aborts before entering EL3, and therefore will contain and
attribute errors to lower EL execution. Any errors thus synchronized are
detected via. DISR_EL1 register.
When RAS_EXTENSION is set to 1, HANDLE_EL3_EA_FIRST must also be set to 1.
Change-Id: I38a19d84014d4d8af688bd81d61ba582c039383a
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
At present, any External Abort routed to EL3 is reported as an unhandled
exception and cause a panic. This patch enables ARM Trusted Firmware to
handle External Aborts routed to EL3.
With this patch, when an External Abort is received at EL3, its handling
is delegated to plat_ea_handler() function. Platforms can provide their
own implementation of this function. This patch adds a weak definition
of the said function that prints out a message and just panics.
In order to support handling External Aborts at EL3, the build option
HANDLE_EA_EL3_FIRST must be set to 1.
Before this patch, HANDLE_EA_EL3_FIRST wasn't passed down to
compilation; this patch fixes that too.
Change-Id: I4d07b7e65eb191ff72d63b909ae9512478cd01a1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.
The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.
Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Since commit 031dbb1224 ("AArch32: Add essential Arch helpers"),
it is difficult to use consistent format strings for printf() family
between aarch32 and aarch64.
For example, uint64_t is defined as 'unsigned long long' for aarch32
and as 'unsigned long' for aarch64. Likewise, uintptr_t is defined
as 'unsigned int' for aarch32, and as 'unsigned long' for aarch64.
A problem typically arises when you use printf() in common code.
One solution could be, to cast the arguments to a type long enough
for both architectures. For example, if 'val' is uint64_t type,
like this:
printf("val = %llx\n", (unsigned long long)val);
Or, somebody may suggest to use a macro provided by <inttypes.h>,
like this:
printf("val = %" PRIx64 "\n", val);
But, both would make the code ugly.
The solution adopted in Linux kernel is to use the same typedefs for
all architectures. The fixed integer types in the kernel-space have
been unified into int-ll64, like follows:
typedef signed char int8_t;
typedef unsigned char uint8_t;
typedef signed short int16_t;
typedef unsigned short uint16_t;
typedef signed int int32_t;
typedef unsigned int uint32_t;
typedef signed long long int64_t;
typedef unsigned long long uint64_t;
[ Linux commit: 0c79a8e29b5fcbcbfd611daf9d500cfad8370fcf ]
This gets along with the codebase shared between 32 bit and 64 bit,
with the data model called ILP32, LP64, respectively.
The width for primitive types is defined as follows:
ILP32 LP64
int 32 32
long 32 64
long long 64 64
pointer 32 64
'long long' is 64 bit for both, so it is used for defining uint64_t.
'long' has the same width as pointer, so for uintptr_t.
We still need an ifdef conditional for (s)size_t.
All 64 bit architectures use "unsigned long" size_t, and most 32 bit
architectures use "unsigned int" size_t. H8/300, S/390 are known as
exceptions; they use "unsigned long" size_t despite their architecture
is 32 bit.
One idea for simplification might be to define size_t as 'unsigned long'
across architectures, then forbid the use of "%z" string format.
However, this would cause a distortion between size_t and sizeof()
operator. We have unknowledge about the native type of sizeof(), so
we need a guess of it anyway. I want the following formula to always
return 1:
__builtin_types_compatible_p(size_t, typeof(sizeof(int)))
Fortunately, ARM is probably a majority case. As far as I know, all
32 bit ARM compilers use "unsigned int" size_t.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
u_register_t is preferred rather than uint64_t. This is more
consistent with the aarch32 implementation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
According to the ARMv8 ARM issue C.a:
AP[1] is valid only for stage 1 of a translation regime that can
support two VA ranges. It is RES 1 when stage 1 translations can
support only one VA range.
This means that, even though this bit is ignored, it should be set to 1
in the EL3 and EL2 translation regimes.
For translation regimes consisting on EL0 and a higher regime this bit
selects between control at EL0 or at the higher Exception level. The
regimes that support two VA ranges are EL1&0 and EL2&0 (the later one
is only available since ARMv8.1).
This fix has to be applied to both versions of the translation tables
library.
Change-Id: If19aaf588551bac7aeb6e9a686cf0c2068e7c181
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Due to differences in the bitfields of the SMC IDs, it is not possible
to support SMCCC 1.X and 2.0 at the same time.
The behaviour of `SMCCC_MAJOR_VERSION` has changed. Now, it is a build
option that specifies the major version of the SMCCC that the Trusted
Firmware supports. The only two allowed values are 1 and 2, and it
defaults to 1. The value of `SMCCC_MINOR_VERSION` is derived from it.
Note: Support for SMCCC v2.0 is an experimental feature to enable
prototyping of secure partition specifications. Support for this
convention is disabled by default and could be removed without notice.
Change-Id: I88abf9ccf08e9c66a13ce55c890edea54d9f16a7
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp SPD=tspd TRUSTED_BOARD_BOOT=1 \
GENERATE_COT=1 ARM_ROTPK_LOCATION=devel_rsa \
ROT_KEY=arm_rotprivk_rsa.pem MBEDTLS_DIR=mbedtls all
Change-Id: Ie4cd6011b3e4fdcdd94ccb97a7e941f3b5b7aeb8
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.3: All declarations of an object or function shall
use the same names and type qualifiers
Fixed for:
make DEBUG=1 PLAT=fvp SPD=tspd TRUSTED_BOARD_BOOT=1 \
GENERATE_COT=1 ARM_ROTPK_LOCATION=devel_rsa \
ROT_KEY=arm_rotprivk_rsa.pem MBEDTLS_DIR=mbedtls all
Change-Id: Ia34fe1ae1f142e89c9a6c19831e3daf4d28f5831
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.5: An external object or function shall be declared
once in one and only one file.
Change-Id: I7c3d4ec7d3ba763fdb4600008ba10b4b93ecdfce
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
A fix for errata 843419 may be available in revision r0p4 of the
Cortex-A53 processor. The presence of the fix is determined by checking
bit 8 in the REVIDR register.
If the fix is present we report ERRATA_NOT_APPLIES which silences the
erroneous 'missing workaround' warning.
Change-Id: Ibd2a478df3e2a6325442a6a48a0bb0259dcfc1d7
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>
This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.
This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>
Some low end platforms using DMC500 memory controller do not have
CCI(Cache Coherent Interconnect) interface and only have non-coherent
system interface support. Hence this patch makes the system interface
count configurable from the platforms.
Change-Id: I6d54c90eb72fd18026c6470c1f7fd26c59dc4b9a
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
For the adr instruction, it require the label's offset from the
address of this instruction must be in the range +/-1MB. If the
option "BL2_IN_XIP_MEM" is set to '1', in some cases, BL2's RW
memory will not in the range of +/-1MB from BL2's RO memory region.
so we need to use ldr instruction to cover this case.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
In some use-cases BL2 will be stored in eXecute In Place (XIP) memory,
like BL1. In these use-cases, it is necessary to initialize the RW sections
in RAM, while leaving the RO sections in place. This patch enable this
use-case with a new build option, BL2_IN_XIP_MEM. For now, this option
is only supported when BL2_AT_EL3 is 1.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Use the console_pl011_core_* functions directly in the crash console
callbacks.
This bypasses the MULTI_CONSOLE_API for the crash console (UART1), but
allows using the crash console before the C runtime has been initialized
(eg to call ASM_ASSERT). This retains backwards compatibility with respect
to functionality when the old API is used.
Use the MULTI_CONSOLE_API to register UART0 as the boot and runtime
console.
FixesARM-software/tf-issues#572
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
Void pointers have been used to access linker symbols, by declaring an
extern pointer, then taking the address of it. This limits symbols
values to aligned pointer values. To remove this restriction an
IMPORT_SYM macro has been introduced, which declares it as a char
pointer and casts it to the required type.
Change-Id: I89877fc3b13ed311817bb8ba79d4872b89bfd3b0
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>
- Interrupt configuration is a 2-bit field, so the field shift has to
be double that of the bit number.
- Interrupt configuration (level- or edge-trigger) is specified in the
MSB of the field, not LSB.
Fixes applied to both GICv2 and GICv3 drivers.
FixesARM-software/tf-issues#570
Change-Id: Ia6ae6ed9ba9fb0e3eb0f921a833af48e365ba359
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Add crash_console_init declaration to console.h
Only enable MULTI_CONSOLE_API for AArch64
FixesARM-software/tf-issues#571
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
When the source code says 'SMCC' it is talking about the SMC Calling
Convention. The correct acronym is SMCCC. This affects a few definitions
and file names.
Some files have been renamed (smcc.h, smcc_helpers.h and smcc_macros.S)
but the old files have been kept for compatibility, they include the
new ones with an ERROR_DEPRECATED guard.
Change-Id: I78f94052a502436fdd97ca32c0fe86bd58173f2f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
When querying `SMCCC_ARCH_WORKAROUND_1` through `SMCCC_ARCH_FEATURES`,
return either:
* -1 to indicate the PE on which `SMCCC_ARCH_FEATURES` is called
requires firmware mitigation for CVE-2017-5715 but the mitigation
is not compiled in.
* 0 to indicate that firmware mitigation is required, or
* 1 to indicate that no firmware mitigation is required.
This patch complies with v1.2 of the firmware interfaces
specification (ARM DEN 0070A).
Change-Id: Ibc32d6620efdac6c340758ec502d95554a55f02a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
If the CSV2 field reads as 1 then branch targets trained in one
context cannot affect speculative execution in a different context.
In that case skip the workaround on Cortex A72 and A73.
Change-Id: Ide24fb6efc77c548e4296295adc38dca87d042ee
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.
The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.
FixesARM-software/tf-issues#559
Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Emit runtime warnings when intializing the GIC drivers using the
deprecated method of defining integer interrupt arrays in the GIC driver
data structures; interrupt_prop_t arrays should be used instead. This
helps platforms detect that they have migration work to do. Previously,
no warning was emitted in this case. This affects both the GICv2 and GICv3
drivers.
Also use the __deprecated attribute to emit a build time warning if these
deprecated fields are used. These warnings are suppressed in the GIC
driver compatibility functions but will be visible if platforms use them.
Change-Id: I6b6b8f6c3b4920c448b6dcb82fc18442cfdf6c7a
Signed-off-by: Dan Handley <dan.handley@arm.com>
For platforms that have not migrated to MULTI_CONSOLE_API == 1, there
are a lot of confusing deprecated declaration warnings relating to
use of console_init() and console_uninit(). Some of these relate to use
by the generic code, not the platform code. These functions are not really
deprecated but *removed* when MULTI_CONSOLE_API == 1.
This patch consolidates these warnings into a single preprocessor warning.
The __deprecated attribute is removed from the console_init() and
console_uninit() declarations.
For preprocessor warnings like this to not cause fatal build errors,
this patch adds -Wno-error=cpp to the build flags when
ERROR_DEPRECATED == 0.
This option (and -Wno-error=deprecated-declarations) is now added to
CPPFLAGS instead of TF_CFLAGS to ensure the build flags are used in the
assembler as well as the compiler.
This patch also disentangles the MULTI_CONSOLE_API and ERROR_DEPRECATED
build flags by defaulting MULTI_CONSOLE_API to 0 instead of
ERROR_DEPRECATED. This allows platforms that have not migrated to
MULTI_CONSOLE_API to use ERROR_DEPRECATED == 1 to emit a more meaningful
build error.
Finally, this patch bans use of MULTI_CONSOLE_API == 1 and AARCH32, since
the AArch32 console implementation does not support
MULTI_CONSOLE_API == 1.
Change-Id: If762165ddcb90c28aa7a4951aba70cb15c2b709c
Signed-off-by: Dan Handley <dan.handley@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=juno LOG_LEVEL=50 all
Change-Id: Ic8f611da734f356566e8208053296e6c62b54709
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.3: All declarations of an object or function shall
use the same names and type qualifiers.
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I48201c9ef022f6bd42ea8644529afce70f9b3f22
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined.
Change-Id: I26e042cb251a6f9590afa1340fdac73e42f23979
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.3: All declarations of an object or function shall
use the same names and type qualifiers.
Change-Id: Iff384187c74a598a4e73f350a1893b60e9d16cec
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
MISRA C-2012 Rule 7.3 violation: lowercase l shall not be used as literal suffixes.
This patch resolves this for the ULL() macro by using ULL suffix instead
of the ull suffix.
Change-Id: Ia8183c399e74677e676956e8653e82375d0e0a01
Signed-off-by: David Cunado <david.cunado@arm.com>
When a Yielding SMC is preempted, it's possible that Non-secure world is
resumed afterwards. In this case, Non-secure execution would find itself
in a state where the SMC has returned. However, the dispatcher might not
get an opportunity to populate the corrected return code for having
been preempted, and therefore the caller of the Yielding SMC cannot
reliably determine whether the SMC had successfully completed or had
been preempted.
To solve this, this patch introduces a new parameter to the
ehf_allow_ns_preemption() API. An SPD, through this parameter, would
provide the expected error code when a Yielding SMC is preempted. EHF
can then populate the specified value in x0 of the Non-secure context so
that the caller of the Yielding SMC correctly identifies the SMC return
as a preemption.
Documentation updates to follow.
Change-Id: Ia9c3f8f03f9d72d81aa235eaae2ee0374b972e1e
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch also fixes the assumption that the counters are disabled on
the resume path. This is incorrect as the AMU counters are enabled
early in the CPU reset function before `cpuamu_context_restore()`
runs.
Change-Id: I38a94eb166a523f00de18e86860434ffccff2131
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch also fixes `cpuamu_write_cpuamcntenclr_el0()` to use an MSR
instruction instead of an MRS instruction.
Change-Id: Ia6531f64b5ebc60ba432124eaa8d8eaccba40ed0
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Implement helpers to test if the core supports SPE/SVE. We have a
similar helper for AMU and this patch makes all extensions consistent
in their implementation.
Change-Id: I3e6f7522535ca358259ad142550b19fcb883ca67
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
When the MMU is enabled and the translation tables are mapped, data
read/writes to the translation tables are made using the attributes
specified in the translation tables themselves. However, the MMU
performs table walks with the attributes specified in TCR_ELx. They are
completely independent, so special care has to be taken to make sure
that they are the same.
This has to be done manually because it is not practical to have a test
in the code. Such a test would need to know the virtual memory region
that contains the translation tables and check that for all of the
tables the attributes match the ones in TCR_ELx. As the tables may not
even be mapped at all, this isn't a test that can be made generic.
The flags used by enable_mmu_xxx() have been moved to the same header
where the functions are.
Also, some comments in the linker scripts related to the translation
tables have been fixed.
Change-Id: I1754768bffdae75f53561b1c4a5baf043b45a304
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :
1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.
2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.
3. The `libfdt` sources are now included when BL2 is built
4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.
5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.
6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.
Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.
Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The `bl1_init_bl2_mem_layout()` API is now deprecated. The default weak
implementation of `bl1_plat_handle_post_image_load()` calculates the
BL2 memory layout and populates the same in x1(r1). This ensures
compatibility for the deprecated API.
Change-Id: Id44bdc1f572dc42ee6ceef4036b3a46803689315
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.
Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch introduces a new BL handover interface. It essentially allows
passing 4 arguments between the different BL stages. Effort has been made
so as to be compatible with the previous handover interface. The previous
blx_early_platform_setup() platform API is now deprecated and the new
blx_early_platform_setup2() variant is introduced. The weak compatiblity
implementation for the new API is done in the `plat_bl_common.c` file.
Some of the new arguments in the new API will be reserved for generic
code use when dynamic configuration support is implemented. Otherwise
the other registers are available for platform use.
Change-Id: Ifddfe2ea8e32497fe1beb565cac155ad9d50d404
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds image IDs to `hw_config` and `tb_fw_config` and
includes them in the default Chain Of Trust (CoT).
Change-Id: If7bb3e9be8a5e48be76614b35bf43d58fc7fed12
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch updates the `fiptool` and `cert_create` for the
`hw_config` and `tb_fw_config` dynamic configuration files.
The necessary UUIDs and OIDs are assigned to these files and
the `cert_create` is updated to generate appropriate hashes
and include them in the "Trusted Boot FW Certificate". The
`fiptool` is updated to allow the configs to be specified
via cmdline and included in the generated FIP.
Change-Id: I940e751a49621ae681d14e162aa1f5697eb0cb15
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds an argument to bl1_plat_post/pre_image_load() APIs
to make it more future proof. The default implementation of
these are moved to `plat_bl1_common.c` file.
These APIs are now invoked appropriately in the FWU code path prior
to or post image loading by BL1 and are not restricted
to LOAD_IMAGE_V2.
The patch also reorganizes some common platform files. The previous
`plat_bl2_el3_common.c` and `platform_helpers_default.c` files are
merged into a new `plat_bl_common.c` file.
NOTE: The addition of an argument to the above mentioned platform APIs
is not expected to have a great impact because these APIs were only
recently added and are unlikely to be used.
Change-Id: I0519caaee0f774dd33638ff63a2e597ea178c453
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Hynix ufs has deviations on hi36xx platform which will result
in ufs bursts transfer failures at a very low probability.
To fix the problem, the Hynix device must set the register
VS_DebugSaveConfigTime to 0x10, which will set time reference
for SaveConfigTime is 250 ns. The time reference for SaveConfigTime
is 40 ns by default.
Signed-off-by: fengbaopeng <fengbaopeng@hisilicon.com>
According to the SMC Calling Convention (ARM DEN0028B):
The Unknown SMC Function Identifier is a sign-extended value of
(-1) that is returned in R0, W0 or X0 register.
The value wasn't sign-extended because it was defined as a 32-bit
unsigned value (0xFFFFFFFF).
SMC_PREEMPT has been redefined as -2 for the same reason.
NOTE: This might be a compatibility break for some AArch64 platforms
that don't follow the previous version of the SMCCC (ARM DEN0028A)
correctly. That document specifies that only the bottom 32 bits of the
returned value must be checked. If a platform relies on the top 32 bits
of the result being 0 (so that SMC_UNK is 0x00000000FFFFFFFF), it will
have to fix its code to comply with the SMCCC.
Change-Id: I7f7b109f6b30c114fe570aa0ead3c335383cb54d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
When ARM Trusted Firmware is built with EL3_EXCEPTION_HANDLING=1,
EL3 interrupts (INTR_TYPE_EL3) will always preempt both Non-secure and
secure execution.
The interrupt management framework currently treats EL3 interrupt
routing as valid. For the above reason, this patch makes them invalid
when EL3_EXCEPTION_HANDLING is in effect.
Change-Id: I95bca8f5dc8df8eb0ff6f305cfba098611522a39
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Add 'lr_svc' as a boot parameter in AArch32 bl1. This is used by Optee
and Trusty to get the non-secure entry point on AArch32 platforms.
This change is not ported in AArch64 mode where the BL31, not BL32,
is in charge of booting the non secure image (BL33).
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
These APIs are used by platforms that need to decompress images.
image_decompress_init():
This registers a temporary buffer and a decompressor callback.
This should be called from platform init code.
image_decompress_prepare():
This should be called before each compressed image is loaded. The
best location to call this will be bl*_plat_handle_pre_image_load().
image_decompress():
This should be called after each compressed image is loaded. The
best location to call this will be bl*_plat_handle_post_image_load().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Just like bl2_, add pre/post image load handlers for BL1. No argument
is needed since BL2 is the only image loaded by BL1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are cases where we need to manipulate image information before
the load. For example, for decompressing data, we cannot load the
compressed images to their final destination. Instead, we need to
load them to the temporary buffer for the decompressor.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This commit adds some more files to use zlib from TF.
To use zlib, ->zalloc and ->zfree hooks are needed. The implementation
depends on the system. For user-space, the libc provides malloc() and
friends. Unfortunately, ARM Trusted Firmware does not provide malloc()
or any concept of dynamic memory allocation.
I implemented very simple calloc() and free() for this. Stupidly,
zfree() never frees memory, but it works enough for this.
The purpose of using zlib is to implement gunzip() - this function
takes compressed data from in_buf, then dumps the decompressed data
to oub_buf. The work_buf is used for memory allocation during the
decompress. Upon exit, it updates in_buf and out_buf. If successful,
in_buf points to the end of input data, out_buf to the end of the
decompressed data.
To use this feature, you need to do:
- include lib/zlib/zlib.mk from your platform.mk
- add $(ZLIB_SOURCES) to your BL*_SOURCES
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add amu_context_save() and amu_context_restore() functions for aarch32
Change-Id: I4df83d447adeaa9d9f203e16dc5a919ffc04d87a
Signed-off-by: Joel Hutton <joel.hutton@arm.com>
In the initial implementation of this workaround we used a dedicated
workaround context to save/restore state. This patch reduces the
footprint as no additional context is needed.
Additionally, this patch reduces the memory loads and stores by 20%,
reduces the instruction count and exploits static branch prediction to
optimize the SMC path.
Change-Id: Ia9f6bf06fbf8a9037cfe7f1f1fb32e8aec38ec7d
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
SMCCC v1.1 comes with a relaxed calling convention for AArch64
callers. The caller only needs to save x0-x3 before doing an SMC
call.
This patch adds support for SMCCC_VERSION and SMCCC_ARCH_FEATURES.
Refer to "Firmware Interfaces for mitigating CVE_2017_5715 System
Software on Arm Systems"[0] for more information.
[0] https://developer.arm.com/-/media/developer/pdf/ARM%20DEN%200070A%20Firmware%20interfaces%20for%20mitigating%20CVE-2017-5715_V1.0.pdf
Change-Id: If5b1c55c17d6c5c7cb9c2c3ed355d3a91cdad0a9
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
The current div_round_up() implementation relies on round_up() which
only works correctly for boundaries that are a power of 2. It is
documented as such, but this still seems dangerously easy to overlook,
especially since many other environments (e.g. the Linux kernel) have a
similar macro without these limitations.
There is a different way to calculate this that can deal with all kinds
of divisors without other drawbacks, so let's just use that instead.
Change-Id: Id382736683f5d4e880ef00c53cfa23a2f9208440
Signed-off-by: Julius Werner <jwerner@chromium.org>
The secure_partition_boot_info_t structure is used to communicate boot
parameters with the StandaloneMM code executing at S-EL0 through a
shared buffer. Certain data types used for members of this structure
are opaque with their size depending on the toolchain being used.
Declare the members of the structure with explicit width based data
types, which would maintain compatibility across toolchains.
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
coreboot supports an in-memory console to store firmware logs even when
no serial console is available. It is widely supported by
coreboot-compatible bootloaders (including SeaBIOS and GRUB) and can be
read by the Linux kernel.
This patch allows BL31 to add its own log messages to this console. The
driver will be registered automatically if coreboot support is compiled
in and detects the presence of a console buffer in the coreboot tables.
Change-Id: I31254dfa0c2fdeb7454634134b5707b4b4154907
Signed-off-by: Julius Werner <jwerner@chromium.org>
This patch adds the foundation for a platform-independent coreboot
support library that can be shared by all platforms that boot BL31 from
coreboot (acting as BL2). It adds code to parse the "coreboot table", a
data structure that coreboot uses to communicate different kinds of
information to later-stage firmware and certain OS drivers.
As a first small use case for this information, allow platforms to
access the serial console configuration used by coreboot, removing the
need to hardcode base address and divisors and allowing Trusted Firmware
to benefit from coreboot's user configuration (e.g. which UART to pick
and which baud rate to use).
Change-Id: I2bfb39cd2609ce6640b844ab68df6c9ae3f28e9e
Signed-off-by: Julius Werner <jwerner@chromium.org>
This patch updates the Cadence CDNS console driver to support the new
console API. The driver will continue to support the old API as well by
checking the MULTI_CONSOLE_API compile-time flag.
Change-Id: I2ef8fb0d6ab72696997db1e0243a533499569d6b
Signed-off-by: Julius Werner <jwerner@chromium.org>
This patch updates the ARM PL011 console driver to support the new
console API. The driver will continue to support the old API as well by
checking the MULTI_CONSOLE_API compile-time flag.
Change-Id: Ic34e4158addbb0c5fae500c9cff899c05a4f4206
Signed-off-by: Julius Werner <jwerner@chromium.org>
This patch updates the TI 16550 console driver to support the new
console API. The driver will continue to support the old API as well by
checking the MULTI_CONSOLE_API compile-time flag.
Change-Id: I60a44b7ba3c35c74561824c04b8dbe3e3039324c
Signed-off-by: Julius Werner <jwerner@chromium.org>
A per-cpu vbar is installed that implements the workaround by
invalidating the branch target buffer (BTB) directly in the case of A9
and A17 and indirectly by invalidating the icache in the case of A15.
For Cortex A57 and A72 there is currently no workaround implemented
when EL3 is in AArch32 mode so report it as missing.
For other vulnerable CPUs (e.g. Cortex A73 and Cortex A75), there are
no changes since there is currently no upstream AArch32 EL3 support
for these CPUs.
Change-Id: Ib42c6ef0b3c9ff2878a9e53839de497ff736258f
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch introduces two workarounds for ARMv7 systems. The
workarounds need to be applied prior to any `branch` instruction in
secure world. This is achieved using a custom vector table where each
entry is an `add sp, sp, #1` instruction.
On entry to monitor mode, once the sequence of `ADD` instructions is
executed, the branch target buffer (BTB) is invalidated. The bottom
bits of `SP` are then used to decode the exception entry type.
A side effect of this change is that the exception vectors are
installed before the CPU specific reset function. This is now
consistent with how it is done on AArch64.
Note, on AArch32 systems, the exception vectors are typically tightly
integrated with the secure payload (e.g. the Trusted OS). This
workaround will need porting to each secure payload that requires it.
The patch to modify the AArch32 per-cpu vbar to the corresponding
workaround vector table according to the CPU type will be done in a
later patch.
Change-Id: I5786872497d359e496ebe0757e8017fa98f753fa
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch change the name of the section containing the functions
defined in assembly files from text.* to text.asm.*. This change
makes possible to select in the linker script the functions
defined in those files.
Change-Id: If35e44ef1b43ffd951dfac5e052db75d7198e2e0
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This patch add supports for the new API added for BL2 at EL3 for
FVP. We don't have a non-TF Boot ROM for FVP, but this option can be
tested setting specific parameters in the model.
The bl2 image is loaded directly in memory instead of being loaded
by a non-TF Boot ROM and the reset address is changed:
--data cluster0.cpu0=bl2.bin@0x4001000
-C cluster0.cpu0.RVBAR=0x4001000
These parameters mean that in the cold boot path the processor will
jump to BL2 again. For this reason, BL2 is loaded in dram in this
case, to avoid other images reclaiming BL2 memory.
Change-Id: Ieb2ff8535a9e67ccebcd8c2212cad366e7776422
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This patch enables BL2 to execute at the highest exception level
without any dependancy on TF BL1. This enables platforms which already
have a non-TF Boot ROM to directly load and execute BL2 and subsequent BL
stages without need for BL1. This is not currently possible because
BL2 executes at S-EL1 and cannot jump straight to EL3.
Change-Id: Ief1efca4598560b1b8c8e61fbe26d1f44e929d69
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Add some macros according to JEDEC Standard Embedded Multi-Media
Card (eMMC) Electrical Standard (5.1)": Table 145 - Bus Mode
Selection.
Change-Id: Iaa45e0582653ef4290efd60d039f0bdc420eeb47
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>
typedef mem_region_t mem_region_t;
... seems to work because they belong to different name-spaces,
but humans are confused even if compilers are not.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On some build configurations BL31 is running out of space. Now that
TSP is moved to secure dram, we have a bit of additional space to use
in BL31.
Change-Id: Ib89fcd8bae99c85c9c5e5d9228bb42fb7048dcb6
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Signed-off-by: David Cunado <david.cunado@arm.com>
On some systems, the AMU counters might reset to 0 when a CPU
powerdown happens. This behaviour conflicts with the intended
use-case of AMU as lower ELs are only expected to see non-decreasing
counter values.
Change-Id: If25519965d4e6e47e09225d0e732947986cbb5ec
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Add some AMU helper functions to allow configuring, reading and
writing of the Group 0 and Group 1 counters. Documentation for these
helpers will come in a separate patch.
Change-Id: I656e070d2dae830c22414f694aa655341d4e2c40
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
A new platform macro `PLAT_AMU_GROUP1_COUNTERS_MASK` controls which
group 1 counters should be enabled. The maximum number of group 1
counters supported by AMUv1 is 16 so the mask can be at most 0xffff.
If the platform does not define this mask, no group 1 counters are
enabled.
A related platform macro `PLAT_AMU_GROUP1_NR_COUNTERS` is used by
generic code to allocate an array to save and restore the counters on
CPU suspend.
Change-Id: I6d135badf4846292de931a43bb563077f42bb47b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
The suspend hook is published at the start of a CPU powerdown
operation. The resume hook is published at the end of a CPU powerup
operation.
Change-Id: I50c05e2dde0d33834095ac41b4fcea4c161bb434
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
If the CSV2 field reads as 1 then branch targets trained in one
context cannot affect speculative execution in a different context.
In that case skip the workaround on Cortex A75.
Change-Id: I4d5504cba516a67311fb5f0657b08f72909cbd38
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Invalidate the Branch Target Buffer (BTB) on entry to EL3 by
temporarily dropping into AArch32 Secure-EL1 and executing the
`BPIALL` instruction.
This is achieved by using 3 vector tables. There is the runtime
vector table which is used to handle exceptions and 2 additional
tables which are required to implement this workaround. The
additional tables are `vbar0` and `vbar1`.
The sequence of events for handling a single exception is
as follows:
1) Install vector table `vbar0` which saves the CPU context on entry
to EL3 and sets up the Secure-EL1 context to execute in AArch32 mode
with the MMU disabled and I$ enabled. This is the default vector table.
2) Before doing an ERET into Secure-EL1, switch vbar to point to
another vector table `vbar1`. This is required to restore EL3 state
when returning from the workaround, before proceeding with normal EL3
exception handling.
3) While in Secure-EL1, the `BPIALL` instruction is executed and an
SMC call back to EL3 is performed.
4) On entry to EL3 from Secure-EL1, the saved context from step 1) is
restored. The vbar is switched to point to `vbar0` in preparation to
handle further exceptions. Finally a branch to the runtime vector
table entry is taken to complete the handling of the original
exception.
This workaround is enabled by default on the affected CPUs.
NOTE
====
There are 4 different stubs in Secure-EL1. Each stub corresponds to
an exception type such as Sync/IRQ/FIQ/SError. Each stub will move a
different value in `R0` before doing an SMC call back into EL3.
Without this piece of information it would not be possible to know
what the original exception type was as we cannot use `ESR_EL3` to
distinguish between IRQs and FIQs.
Change-Id: I90b32d14a3735290b48685d43c70c99daaa4b434
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Invalidate the Branch Target Buffer (BTB) on entry to EL3 by disabling
and enabling the MMU. To achieve this without performing any branch
instruction, a per-cpu vbar is installed which executes the workaround
and then branches off to the corresponding vector entry in the main
vector table. A side effect of this change is that the main vbar is
configured before any reset handling. This is to allow the per-cpu
reset function to override the vbar setting.
This workaround is enabled by default on the affected CPUs.
Change-Id: I97788d38463a5840a410e3cea85ed297a1678265
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Rename SP_VERSION macros to MM_VERSION, which is the name used in the MM
specification [1]. Also, a few more helper macros have been added.
MM-specific definitions have been moved to their own header file.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0060a/DEN0060A_ARM_MM_Interface_Specification.pdf
Change-Id: Ia10e48c7e81a7a1f5eeca29a5270cae740a4a88a
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch adds support to receive function ID with NS world's
memory ranges to provide the memory snapshot to TLK.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
To allow BL31 to grow in SRAM, move TSP in TZC secured DRAM
by default.
Increase the BL31 max limit by one page.
Change-Id: Idd3479be02f0f9bafac2f275376d7db0c2015431
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.
Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This patch overhauls the console API to allow for multiple console
instances of different drivers that are active at the same time. Instead
of binding to well-known function names (like console_core_init),
consoles now provide a register function (e.g. console_16550_register())
that will hook them into the list of active consoles. All console
operations will be dispatched to all consoles currently in the list.
The new API will be selected by the build-time option MULTI_CONSOLE_API,
which defaults to ${ERROR_DEPRECATED} for now. The old console API code
will be retained to stay backwards-compatible to older platforms, but
should no longer be used for any newly added platforms and can hopefully
be removed at some point in the future.
The new console API is intended to be used for both normal (bootup) and
crash use cases, freeing platforms of the need to set up the crash
console separately. Consoles can be individually configured to be active
active at boot (until first handoff to EL2), at runtime (after first
handoff to EL2), and/or after a crash. Console drivers should set a sane
default upon registration that can be overridden with the
console_set_scope() call. Code to hook up the crash reporting mechanism
to this framework will be added with a later patch.
This patch only affects AArch64, but the new API could easily be ported
to AArch32 as well if desired.
Change-Id: I35c5aa2cb3f719cfddd15565eb13c7cde4162549
Signed-off-by: Julius Werner <jwerner@chromium.org>
In assembly code it can be useful to have a constant for the width of a
register in the current architecture, so this patch adds one to
<utils_def.h> and replaces the existing custom one in crash_reporting.S
with that. It also fixes up the BIT() macro in the same file so that it
can be safely used in assembly code.
Change-Id: I10513a311f3379e767396e6ddfbae8d2d8201464
Signed-off-by: Julius Werner <jwerner@chromium.org>
A new platform define, `PLAT_SP_IMAGE_XLAT_SECTION_NAME`, has been
introduced to select the section where the translation tables used by
the S-EL1/S-EL0 are placed.
This define has been used to move the translation tables to DRAM secured
by TrustZone.
Most of the extra needed space in BL31 when SPM is enabled is due to the
large size of the translation tables. By moving them to this memory
region we can save 44 KiB.
A new argument has been added to REGISTER_XLAT_CONTEXT2() to specify the
region where the translation tables have to be placed by the linker.
Change-Id: Ia81709b4227cb8c92601f0caf258f624c0467719
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Previously the cache flush happened in 2 different places in code
depending on whether TRUSTED_BOARD_BOOT is enabled or not. This
patch unifies this code path for both the cases. The `load_image()`
function is now made an internal static function.
Change-Id: I96a1da29d29236bbc34b1c95053e6a9a7fc98a54
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The defines have been renamed to match the names used in the
documentation.
Change-Id: I2f18b65112d2db040a89d5a8522e9790c3e21628
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch adds a new build option, ENABLE_SVE_FOR_NS, which when set
to one EL3 will check to see if the Scalable Vector Extension (SVE) is
implemented when entering and exiting the Non-secure world.
If SVE is implemented, EL3 will do the following:
- Entry to Non-secure world: SIMD, FP and SVE functionality is enabled.
- Exit from Non-secure world: SIMD, FP and SVE functionality is
disabled. As SIMD and FP registers are part of the SVE Z-registers
then any use of SIMD / FP functionality would corrupt the SVE
registers.
The build option default is 1. The SVE functionality is only supported
on AArch64 and so the build option is set to zero when the target
archiecture is AArch32.
This build option is not compatible with the CTX_INCLUDE_FPREGS - an
assert will be raised on platforms where SVE is implemented and both
ENABLE_SVE_FOR_NS and CTX_INCLUDE_FPREGS are set to 1.
Also note this change prevents secure world use of FP&SIMD registers on
SVE-enabled platforms. Existing Secure-EL1 Payloads will not work on
such platforms unless ENABLE_SVE_FOR_NS is set to 0.
Additionally, on the first entry into the Non-secure world the SVE
functionality is enabled and the SVE Z-register length is set to the
maximum size allowed by the architecture. This includes the use case
where EL2 is implemented but not used.
Change-Id: Ie2d733ddaba0b9bef1d7c9765503155188fe7dae
Signed-off-by: David Cunado <david.cunado@arm.com>
This patch fixes a couple of issues for AArch32 builds on ARM reference
platforms :
1. The arm_def.h previously defined the same BL32_BASE value for AArch64 and
AArch32 build. Since BL31 is not present in AArch32 mode, this meant that
the BL31 memory is empty when built for AArch32. Hence this patch allocates
BL32 to the memory region occupied by BL31 for AArch32 builds.
As a side-effect of this change, the ARM_TSP_RAM_LOCATION macro cannot
be used to control the load address of BL32 in AArch32 mode which was
never the intention of the macro anyway.
2. A static assert is added to sp_min linker script to check that the progbits
are within the bounds expected when overlaid with other images.
3. Fix specifying `SPD` when building Juno for AArch32 mode. Due to the quirks
involved when building Juno for AArch32 mode, the build option SPD needed to
specifed. This patch corrects this and also updates the documentation in the
user-guide.
4. Exclude BL31 from the build and FIP when building Juno for AArch32 mode. As
a result the previous assumption that BL31 must be always present is removed
and the certificates for BL31 is only generated if `NEED_BL31` is defined.
Change-Id: I1c39bbc0abd2be8fbe9f2dea2e9cb4e3e3e436a8
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
When defining different sections in linker scripts it is needed to align
them to multiples of the page size. In most linker scripts this is done
by aligning to the hardcoded value 4096 instead of PAGE_SIZE.
This may be confusing when taking a look at all the codebase, as 4096
is used in some parts that aren't meant to be a multiple of the page
size.
Change-Id: I36c6f461c7782437a58d13d37ec8b822a1663ec1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The `ENABLE_AMU` build option can be used to enable the
architecturally defined AMU counters. At present, there is no support
for the auxiliary counter group.
Change-Id: Ifc7532ef836f83e629f2a146739ab61e75c4abc8
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
The `ENABLE_AMU` build option can be used to enable the
architecturally defined AMU counters. At present, there is no support
for the auxiliary counter group.
Change-Id: I7ea0c0a00327f463199d1b0a481f01dadb09d312
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
The Cortex A75 has 5 AMU counters. The first three counters are fixed
and the remaining two are programmable.
A new build option is introduced, `ENABLE_AMU`. When set, the fixed
counters will be enabled for use by lower ELs. The programmable
counters are currently disabled.
Change-Id: I4bd5208799bb9ed7d2596e8b0bfc87abbbe18740
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
The flag support the following values:
- sha256 (default)
- sha384
- sha512
Change-Id: I7a49d858c361e993949cf6ada0a86575c3291066
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>
Factor out SPE operations in a separate file. Use the publish
subscribe framework to drain the SPE buffers before entering secure
world. Additionally, enable SPE before entering normal world.
A side effect of this change is that the profiling buffers are now
only drained when a transition from normal world to secure world
happens. Previously they were drained also on return from secure
world, which is unnecessary as SPE is not supported in S-EL1.
Change-Id: I17582c689b4b525770dbb6db098b3a0b5777b70a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Register count is currently declared as unsigned, where as there are
asserts in place to check it being negative during unregister. These are
flagged as never being true.
Change-Id: I34f00f0ac5bf88205791e9c1298a175dababe7c8
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
If an implementation of ARMv8.2 includes ARMv8.2-LPA, the value 0b0110
is permitted in ID_AA64MMFR0_EL1.PARange, which means that the Physical
Address range supported is 52 bits (4 PiB). It is a reserved value
otherwise.
Change-Id: Ie0147218e9650aa09f0034a9ee03c1cca8db908a
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The FPEXC32_EL2 register controls SIMD and FP functionality when the
lower ELs are executing in AArch32 mode. It is architecturally mapped
to AArch32 system register FPEXC.
This patch removes FPEXC32_EL2 register from the System Register context
and adds it to the floating-point context. EL3 only saves / restores the
floating-point context if the build option CTX_INCLUDE_FPREGS is set to 1.
The rationale for this change is that if the Secure world is using FP
functionality and EL3 is not managing the FP context, then the Secure
world will save / restore the appropriate FP registers.
NOTE - this is a break in behaviour in the unlikely case that
CTX_INCLUDE_FPREGS is set to 0 and the platform contains an AArch32
Secure Payload that modifies FPEXC, but does not save and restore
this register
Change-Id: Iab80abcbfe302752d52b323b4abcc334b585c184
Signed-off-by: David Cunado <david.cunado@arm.com>
This allows for other EL3 components to schedule an SDEI event dispatch
to Normal world upon the next ERET. The API usage constrains are set out
in the SDEI dispatcher documentation.
Documentation to follow.
Change-Id: Id534bae0fd85afc94523490098c81f85c4e8f019
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Support SDEI on ARM platforms using frameworks implemented in earlier
patches by defining and exporting SDEI events: this patch defines the
standard event 0, and a handful of shared and private dynamic events.
Change-Id: I9d3d92a92cff646b8cc55eabda78e140deaa24e1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Define number of priority bits, and allocate priority levels for SDEI.
Change-Id: Ib6bb6c5c09397f7caef950c4caed5a737b3d4112
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Provide a strong definition for plat_sdei_validate_sdei_entrypoint()
which translates client address to Physical Address, and then validating
the address to be present in DRAM.
Change-Id: Ib93eb66b413d638aa5524d1b3de36aa16d38ea11
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The function arm_validate_ns_entrypoint() validates a given non-secure
physical address. This function however specifically returns PSCI error
codes.
Non-secure physical address validation is potentially useful across ARM
platforms, even for non-PSCI use cases. Therefore make this function
common by returning 0 for success or -1 otherwise.
Having made the function common, make arm_validate_psci_entrypoint() a
wrapper around arm_validate_ns_entrypoint() which only translates return
value into PSCI error codes. This wrapper is now used where
arm_validate_ns_entrypoint() was currently used for PSCI entry point
validation.
Change-Id: Ic781fc3105d6d199fd8f53f01aba5baea0ebc310
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The implementation currently supports only interrupt-based SDEI events,
and supports all interfaces as defined by SDEI specification version
1.0 [1].
Introduce the build option SDEI_SUPPORT to include SDEI dispatcher in
BL31.
Update user guide and porting guide. SDEI documentation to follow.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0054a/ARM_DEN0054A_Software_Delegated_Exception_Interface.pdf
Change-Id: I758b733084e4ea3b27ac77d0259705565842241a
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
On GICv3 systems, as a side effect of adding provision to handle EL3
interrupts (unconditionally routing FIQs to EL3), pending Non-secure
interrupts (signalled as FIQs) may preempt execution in lower Secure ELs
[1]. This will inadvertently disrupt the semantics of Fast SMC
(previously called Atomic SMC) calls.
To retain semantics of Fast SMCs, the GIC PMR must be programmed to
prevent Non-secure interrupts from preempting Secure execution. To that
effect, two new functions in the Exception Handling Framework subscribe
to events introduced in an earlier commit:
- Upon 'cm_exited_normal_world', the Non-secure PMR is stashed, and
the PMR is programmed to the highest Non-secure interrupt priority.
- Upon 'cm_entering_normal_world', the previously stashed Non-secure
PMR is restored.
The above sequence however prevents Yielding SMCs from being preempted
by Non-secure interrupts as intended. To facilitate this, the public API
exc_allow_ns_preemption() is introduced that programs the PMR to the
original Non-secure PMR value. Another API
exc_is_ns_preemption_allowed() is also introduced to check if
exc_allow_ns_preemption() had been called previously.
API documentation to follow.
[1] On GICv2 systems, this isn't a problem as, unlike GICv3, pending NS
IRQs during Secure execution are signalled as IRQs, which aren't
routed to EL3.
Change-Id: Ief96b162b0067179b1012332cd991ee1b3051dd0
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
EHF is a framework that allows dispatching of EL3 interrupts to their
respective handlers in EL3.
This framework facilitates the firmware-first error handling policy in
which asynchronous exceptions may be routed to EL3. Such exceptions may
be handed over to respective exception handlers. Individual handlers
might further delegate exception handling to lower ELs.
The framework associates the delegated execution to lower ELs with a
priority value. For interrupts, this corresponds to the priorities
programmed in GIC; for other types of exceptions, viz. SErrors or
Synchronous External Aborts, individual dispatchers shall explicitly
associate delegation to a secure priority. In order to prevent lower
priority interrupts from preempting higher priority execution, the
framework provides helpers to control preemption by virtue of
programming Priority Mask register in the interrupt controller.
This commit allows for handling interrupts targeted at EL3. Exception
handlers own interrupts by assigning them a range of secure priorities,
and registering handlers for each priority range it owns.
Support for exception handling in BL31 image is enabled by setting the
build option EL3_EXCEPTION_HANDLING=1.
Documentation to follow.
NOTE: The framework assumes the priority scheme supported by platform
interrupt controller is compliant with that of ARM GIC architecture (v2
or later).
Change-Id: I7224337e4cea47c6ca7d7a4ca22a3716939f7e42
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Acknowledging interrupt shall return a raw value from the interrupt
controller in which the actual interrupt ID may be encoded. Add a
platform API to extract the actual interrupt ID from the raw value
obtained from interrupt controller.
Document the new function. Also clarify the semantics of interrupt
acknowledge.
Change-Id: I818dad7be47661658b16f9807877d259eb127405
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This initial port of the Secure Partitions Manager to FVP supports BL31
in both SRAM and Trusted DRAM.
A document with instructions to build the SPM has been added.
Change-Id: I4ea83ff0a659be77f2cd72eaf2302cdf8ba98b32
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Achin Gupta <achin.gupta@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
A Secure Partition is a software execution environment instantiated in
S-EL0 that can be used to implement simple management and security
services. Since S-EL0 is an unprivileged exception level, a Secure
Partition relies on privileged firmware e.g. ARM Trusted Firmware to be
granted access to system and processor resources. Essentially, it is a
software sandbox that runs under the control of privileged software in
the Secure World and accesses the following system resources:
- Memory and device regions in the system address map.
- PE system registers.
- A range of asynchronous exceptions e.g. interrupts.
- A range of synchronous exceptions e.g. SMC function identifiers.
A Secure Partition enables privileged firmware to implement only the
absolutely essential secure services in EL3 and instantiate the rest in
a partition. Since the partition executes in S-EL0, its implementation
cannot be overly complex.
The component in ARM Trusted Firmware responsible for managing a Secure
Partition is called the Secure Partition Manager (SPM). The SPM is
responsible for the following:
- Validating and allocating resources requested by a Secure Partition.
- Implementing a well defined interface that is used for initialising a
Secure Partition.
- Implementing a well defined interface that is used by the normal world
and other secure services for accessing the services exported by a
Secure Partition.
- Implementing a well defined interface that is used by a Secure
Partition to fulfil service requests.
- Instantiating the software execution environment required by a Secure
Partition to fulfil a service request.
Change-Id: I6f7862d6bba8732db5b73f54e789d717a35e802f
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Achin Gupta <achin.gupta@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This function can be useful to setup TCR_ELx by callers that don't use
the translation tables library to setup the system registers related
to them. By making it common, it can be reused whenever it is needed
without duplicating code.
Change-Id: Ibfada9e846d2a6cd113b1925ac911bb27327d375
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Some SoCs integrate a GIC in version 1 that is currently not supported
by the trusted firmware. This change hijacks GICv2 driver to handle the
GICv1 as GICv1 is compatible enough with GICv2 as far as the platform
does not attempt to play with virtualization support or some GICv2
specific power features.
Note that current trusted firmware does not use these GICv2 features
that are not available in GICv1 Security Extension.
Change-Id: Ic2cb3055f1319a83455571d6d918661da583f179
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
ARMv7-A Virtualization extensions brings new instructions and resources
that were supported by later architectures. Reference ARM ARM Issue C.c
[DDI0406C_C].
ERET and extended MSR/MRS instructions, as specified in [DDI0406C_C] in
ID_PFR1 description of bits[15:12] (Virtualization Extensions):
A value of 0b0001 implies implementation of the HVC, ERET, MRS
(Banked register), and MSR (Banked register) instructions. The ID_ISARs
do not identify whether these instructions are implemented.
UDIV/SDIV were introduced with the Virtualization extensions, even if
not strictly related to the virtualization extensions.
If ARMv7 based platform does not set ARM_CORTEX_Ax=yes, platform
shall define ARMV7_SUPPORTS_VIRTUALIZATION to enable virtualization
extension related resources.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
As Cortex-A9 needs to manually enable program flow prediction,
do not reset SCTLR[Z] at entry. Platform should enable it only
once MMU is enabled.
Change-Id: I34e1ee2da73221903f7767f23bc6fc10ad01e3de
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
These macros are only defined for corresponding image,
and they are undefined for other images. It means that we have
to use ifdef or defined() instead of relying on being 0 by default.
Change-Id: Iad11efab9830ddf471599b46286e1c56581ef5a7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Change sizeof call so it references a static type instead of return of
a function in order to be MISRA compliant.
Change-Id: I6f1adb206073d6cd200156e281b8d76249e3af0e
Signed-off-by: Joel Hutton <joel.hutton@arm.com>
Add events that trigger before entry to normal/secure world. The
events trigger after the normal/secure context has been restored.
Similarly add events that trigger after leaving normal/secure world.
The events trigger after the normal/secure context has been saved.
Change-Id: I1b48a7ea005d56b1f25e2b5313d77e67d2f02bc5
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
For Trusted Board Boot, BL2 needs more space to support the ECDSA
and ECDSA+RSA algorithms.
Change-Id: Ie7eda9a1315ce836dbc6d18d6588f8d17891a92d
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>
These hooks are intended to allow one platform to try load
images from alternative places. There is a hook to initialize
the sequence of boot locations and a hook to pass to the next
sequence.
Change-Id: Ia0f84c415208dc4fa4f9d060d58476db23efa5b2
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
This allows other EL3 components to subscribe to CPU on events.
Update Firmware Design guide to list psci_cpu_on_finish as an available
event.
Change-Id: Ida774afe0f9cdce4021933fcc33a9527ba7aaae2
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
This light-weight framework enables some EL3 components to publish
events which other EL3 components can subscribe to. Publisher can
optionally pass opaque data for subscribers. The order in which
subscribers are called is not defined.
Firmware design updated.
Change-Id: I24a3a70b2b1dedcb1f73cf48313818aebf75ebb6
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The implementation is the same as those used to disable it in EL3.
Change-Id: Ibfe7e69034a691fbf57477c5a76a8cdca28f6b26
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch introduces a new API in the translation tables library
(v2), that allows to change the memory attributes of a memory
region. It may be used to change its execution permissions and
data access permissions.
As a prerequisite, the memory must be already mapped. Moreover, it
must be mapped at the finest granularity (currently 4 KB).
Change-Id: I242a8c6f0f3ef2b0a81a61e28706540462faca3c
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch introduces a new API in the translation tables library
(v2), that allows to query the memory attributes of a memory block
or a memory page.
Change-Id: I45a8b39a53da39e7617cbac4bff5658dc1b20a11
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Previously, in AArch32, `IMAGE_XLAT_DEFAULT_REGIME` wasn't defined. The
translation regime is only used in the AArch64 port of the translation
tables library v2, so this is not a problem for now, but future patches
will use it.
`IMAGE_EL` isn't used in AArch32, so it isn't needed to define it.
Change-Id: I4acdb01a58658956ab94bd82ed5b7fee1aa6ba90
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The GIC driver initialization currently allows an array of interrupts to
be configured as secure. Future use cases would require more interrupt
configuration other than just security, such as priority.
This patch introduces a new interrupt property array as part of both
GICv2 and GICv3 driver data. The platform can populate the array with
interrupt numbers and respective properties. The corresponding driver
initialization iterates through the array, and applies interrupt
configuration as required.
This capability, and the current way of supplying array (or arrays, in
case of GICv3) of secure interrupts, are however mutually exclusive.
Henceforth, the platform should supply either:
- A list of interrupts to be mapped as secure (the current way).
Platforms that do this will continue working as they were. With this
patch, this scheme is deprecated.
- A list of interrupt properties (properties include interrupt group).
Individual interrupt properties are specified via. descriptors of
type 'interrupt_prop_desc_t', which can be populated with the macro
INTR_PROP_DESC().
A run time assert checks that the platform doesn't specify both.
Henceforth the old scheme of providing list of secure interrupts is
deprecated. When built with ERROR_DEPRECATED=1, GIC drivers will require
that the interrupt properties are supplied instead of an array of secure
interrupts.
Add a section to firmware design about configuring secure interrupts.
FixesARM-software/tf-issues#262
Change-Id: I8eec29e72eb69dbb6bce77879febf32c95376942
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The helpers perform read-modify-write on GIC*_ICFGR registers, but don't
serialise callers. Any serialisation must be taken care of by the
callers.
Change-Id: I71995f82ff2c7f70d37af0ede30d6ee18682fd3f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
An earlier patch added provision for the platform to provide secure
interrupt properties. ARM platforms already has a list of interrupts
that fall into different secure groups.
This patch defines macros that enumerate interrupt properties in the
same fashion, and points the driver driver data to a list of interrupt
properties rather than list of secure interrupts on ARM platforms. The
deprecated interrupt list definitions are however retained to support
legacy builds.
Configuration applied to individual interrupts remain unchanged, so no
runtime behaviour change expected.
NOTE: Platforms that use the arm/common function
plat_arm_gic_driver_init() must replace their PLAT_ARM_G1S_IRQS and
PLAT_ARM_G0_IRQS macro definitions with PLAT_ARM_G1S_IRQ_PROPS and
PLAT_ARM_G0_IRQ_PROPS macros respectively, using the provided
INTR_PROP_DESC macro.
Change-Id: I24d643b83e3333753a3ba97d4b6fb71e16bb0952
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
SPIs can be routed to either a specific PE, or to any one of all
available PEs.
API documentation updated.
Change-Id: I28675f634568aaf4ea1aa8aa7ebf25b419a963ed
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The back end GIC driver converts and assigns the interrupt type to
suitable group.
For GICv2, a build option GICV2_G0_FOR_EL3 is introduced, which
determines to which type Group 0 interrupts maps to.
- When the build option is set 0 (the default), Group 0 interrupts are
meant for Secure EL1. This is presently the case.
- Otherwise, Group 0 interrupts are meant for EL3. This means the SPD
will have to synchronously hand over the interrupt to Secure EL1.
The query API allows the platform to query whether the platform supports
interrupts of a given type.
API documentation updated.
Change-Id: I60fdb4053ffe0bd006b3b20914914ebd311fc858
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
These APIs allow the GIC implementation to categorize interrupt numbers
into SPIs, PPIs, and SGIs. The default implementations for GICv2 and
GICv3 follows interrupt numbering as specified by the ARM GIC
architecture.
API documentation updated.
Change-Id: Ia6aa379dc955994333232e6138f259535d4fa087
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The PE target mask is used to translate linear PE index (returned by
platform core position) to a bit mask used when targeting interrupts to
a PE, viz. when raising SGIs and routing SPIs.
The platform shall:
- Populate the driver data with a pointer to array that's to contain
per-PE target masks.
- Invoke the new driver API 'gicv2_set_pe_target_mask()' during
per-CPU initialization so that the driver populates the target mask
for that CPU.
Platforms that don't intend to target interrupts or raise SGIs need not
populate this.
Change-Id: Ic0db54da86915e9dccd82fff51479bc3c1fdc968
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Document the API in separate platform interrupt controller API document.
Change-Id: If18f208e10a8a243f5c59d226fcf48e985941949
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
The macro DEFINE_SYSREG_WRITE_CONST_FUNC defines an inline function
to an assembly statement that uses the MSR (immediate) instruction
to access the PSTATE. The "i" (immediate) assembly constraint on
the operand was only satisfied when compiling with optimizations
enabled which resulted in the function being optimized out - the
"const uint64_t v" parameter was optimized out and replaced by a
literal value.
When compiling without optimizations, the function call remained and
therefore the parameter is not optimized out - compilation fails as
the constraint is impossible to satisfy by the compiler.
This patch replaces the function encapsulating the use of
the MSR (immediate) with a macro that allows the literal value to be
directly fed to the inline assembly statement
Change-Id: Ib379a7acc48ef3cb83090a680cd8a6ce1a94a9d9
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Updated the PSCI version conforming to the PSCI v1.1
specification (ARM DEN022D).
Change-Id: I1f34772ef6de37ec1ade719a1ab3aa062152d995
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Currently TF does not initialise the PMCR_EL0 register in
the secure context or save/restore the register.
In particular, the DP field may not be set to one to prohibit
cycle counting in the secure state, even though event counting
generally is prohibited via the default setting of MDCR_EL3.SMPE
to 0.
This patch initialises PMCR_EL0.DP to one in the secure state
to prohibit cycle counting and also initialises other fields
that have an architectually UNKNOWN reset value.
Additionally, PMCR_EL0 is added to the list of registers that are
saved and restored during a world switch.
Similar changes are made for PMCR for the AArch32 execution state.
NOTE: secure world code at lower ELs that assume other values in PMCR_EL0
will be impacted.
Change-Id: Iae40e8c0a196d74053accf97063ebc257b4d2f3a
Signed-off-by: David Cunado <david.cunado@arm.com>
This patch implements PSCI_SYSTEM_RESET2 API as defined in PSCI
v1.1 specification. The specification allows architectural and
vendor-specific resets via this API. In the current specification,
there is only one architectural reset, the warm reset. This reset is
intended to provide a fast reboot path that guarantees not to reset
system main memory.
Change-Id: I057bb81a60cd0fe56465dbb5791d8e1cca025bd3
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Provides GICv3 save/restore feature to arm_system_pwr_domain_resume and
arm_system_pwr_domain_save functions.
Introduce FVP PSCI power level 3 (System level) support. This is solely
done to provide example code on how to use the GICv3 save and restore
helpers.
Also make CSS GICv3 platforms power off the Redistributor on SYSTEM
SUSPEND as its state is saved and restored.
Change-Id: I0d852f3af8824edee1a17c085cf593ddd33a4e77
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Co-Authored-by: Douglas Raillard <douglas.raillard@arm.com>
Some recent enhancements to EL3 runtime firmware like support for
save and restoring GICv3 register context during system_suspend
necessitates additional data memory for the firmware. This patch
introduces support for creating a TZC secured DDR carveout for use
by ARM reference platforms. A new linker section `el3_tzc_dram` is
created using platform supplied linker script and data marked with
the attribute `arm_el3_tzc_dram` will be placed in this section.
The FVP makefile now defines the `PLAT_EXTRA_LD_SCRIPT` variable to
allow inclusion of the platform linker script by the top level BL31
linker script.
Change-Id: I0e7f4a75a6ac51419c667875ff2677043df1585d
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The MEM_PROTECT support adds a MMAP region for DRAM2, which when
building with TBBR support and OP-TEE tsp requires an additional
entry in the MMAP region array in BL2 - PLAT_ARM_MMAP_ENTRIES is
increased.
The MEM_PROTECT support also adds a new region in BL31, and when
BL31 is placed in DRAM, the memory mappings require an additional
translation table - MAX_XLAT_TABLES is increased.
Change-Id: I0b76260da817dcfd0b8f73a7193c36efda977625
Signed-off-by: David Cunado <david.cunado@arm.com>
This patch adds functions to save and restore GICv3 ITS registers during
system suspend. Please note that the power management of GIC ITS is
implementation defined. These functions only implements the
architectural part of the ITS power management and they do not restore
memory structures or register content required to support ITS. Even if
the ITS implementation stores structures in memory, an implementation
defined power down sequence is likely to be required to flush some
internal ITS caches to memory. If such implementation defined sequence
is not followed, the platform must ensure that the ITS is not power
gated during system suspend.
Change-Id: I5f31e5541975aa7dcaab69b0b7f67583c0e27678
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
During system suspend, the GICv3 Distributor and Redistributor context
can be lost due to power gating of the system power domain. This means
that the GICv3 context needs to be saved prior to system suspend and
restored on wakeup. Currently the consensus is that the Firmware should
be in charge of this. See tf-issues#464 for more details.
This patch introduces helper APIs in the GICv3 driver to save and
restore the Distributor and Redistributor contexts. The GICv3 ITS
context is not considered in this patch because the specification says
that the details of ITS power management is implementation-defined.
These APIs are expected to be appropriately invoked by the platform
layer during system suspend.
FixesARM-software/tf-issues#464
Change-Id: Iebb9c6770ab8c4d522546f161fa402d2fe02ec00
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
This patch introduces the ability of the xlat tables library to manage
EL0 and EL1 mappings from a higher exception level.
Attributes MT_USER and MT_PRIVILEGED have been added to allow the user
specify the target EL in the translation regime EL1&0.
REGISTER_XLAT_CONTEXT2 macro is introduced to allow creating a
xlat_ctx_t that targets a given translation regime (EL1&0 or EL3).
A new member is added to xlat_ctx_t to represent the translation regime
the xlat_ctx_t manages. The execute_never mask member is removed as it
is computed from existing information.
Change-Id: I95e14abc3371d7a6d6a358cc54c688aa9975c110
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Introduce a variant of the TLB invalidation helper function that
allows the targeted translation regime to be specified, rather than
defaulting to the current one.
This new function is useful in the context of EL3 software managing
translation tables for the S-EL1&0 translation regime, as then it
might need to invalidate S-EL1&0 TLB entries rather than EL3 ones.
Define a new enumeration to be able to represent translation regimes in
the xlat tables library.
Change-Id: Ibe4438dbea2d7a6e7470bfb68ff805d8bf6b07e5
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The current implementation of the memory mapping API favours mapping
memory regions using the biggest possible block size in order to
reduce the number of translation tables needed.
In some cases, this behaviour might not be desirable. When translation
tables are edited at run-time, coarse-grain mappings like that might
need splitting into finer-grain tables. This operation has a
performance cost.
The MAP_REGION2() macro allows to specify the granularity of
translation tables used for the initial mapping of a memory region.
This might increase performance for memory regions that are likely to
be edited in the future, at the expense of a potentially increased
memory footprint.
The Translation Tables Library Design Guide has been updated to
explain the use case for this macro. Also added a few intermediate
titles to make the guide easier to digest.
Change-Id: I04de9302e0ee3d326b8877043a9f638766b81b7b
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Qixiang Xu
Soby Mathew
Daniel Boulby
Dimitris Papastamos
Antonio Nino Diaz
Chris Kay
Roberto Vargas
danh-arm
Jeenu Viswambharan
Masahiro Yamada
Jonathan Wright
Summer Qin
Amit Daniel Kachhap
Jiafei Pan
Michalis Pappas
Joel Hutton
davidcunado-arm
fengbaopeng
Etienne Carriere
Julius Werner
Sughosh Ganu
Varun Wadekar
Sandrine Bailleux
Douglas Raillard