RESTORE/SAVE_GICD_EREGS uses (int_id - (MIN_ESPI_ID - MIN_SPI_ID)) to
get the context array index for ESPI, which will override the space of
standard SPI starting from (MIN_SPI_ID + MIN_SPI_ID).
However, using TOTAL_SPI_INTR_NUM to replace the above MIN_SPI_ID
cannot totally fix the issue, for TOTAL_SPI_INTR_NUM is not well
aligned and the array index will be rounded down by the shifting
operation if being shifted more than 2 bits. It will cause buffer
override again when the existing maximum SPI reaches 1019.
So round up TOTAL_SPI_INTR_NUM with (1 << REG##R_SHIFT) for GICD
context arrays.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I5be2837c42f381a62f8d46a4ecd778009b1fe059
In function gicv3_rdistif_probe(), line #1322 implies
gicv3_driver_data->mpidr_to_core_pos() may be null, but the original
code uses this interface to get current CPU index unconditionally.
It is better to use MPIDR to probe GICR which does not depend on
gicv3_driver_data->mpidr_to_core_pos().
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I64add055385040fe0a56b977e2299608e2309a6e
This patch does not change code, it only updates comments and macro name
for 6th bit of Status Register. So TF-A binary stay same.
6th bit of the Status Register is named TX EMPTY and is set to 1 when both
Transmitter Holding Register (THR) or Transmitter Shift Register (TSR) are
empty. It is when all characters were already transmitted.
There is also TX FIFO EMPTY bit in the Status Register which is set to 1
only when THR is empty.
In both console_a3700_core_init() and console_a3700_core_flush() functions
we should wait until both THR and TSR are empty therefore we should check
6th bit of the Status Register.
So current code is correct, just had misleading macro names and comments.
This change fixes this "documentation" issue, fixes macro name for 6th bit
of the Status Register and also updates comments.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I19e4e7f53a90bcfb318e6dd1b1249b6cbf81c4d3
Implementation is simple, just check if there is a pending character in
RX FIFO via RXRDY bit of Status Register and if yes, read it from
UART_RX_REG register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I226b6e336f44f5d0ca8dcb68e49a68e8f2f49708
Add pin control support for RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I08719015cab1ec59e2270523980a0a3e26e72c01
Add support for initializing DRAM on RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I99f1a6971a061a44687af498d55306a93e4fc8f7
Move DDR/QoS/PFC header files, so that the same code
can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I2cc0ceda8d05b6b8d95a69afdc233dc0d098e850
Move rpc driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I04805d720d95b8edcc14e652f897fadc7f432197
Move avs driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I85d9fa8b6abf158ce2521f1696478f7c5339fc42
Move authentication driver code to common directory, so that the
same code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I02592dfc714998bf89b9feaa78f685ae36be6f59
Move dma driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Idce2e2f4e098cfc17219f963373d20ebf74e5b7c
Move watch driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I235f2cde325a0feeadbfc4b7ee02e8b1186f7ea1
Move rom driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I399dfb5eff186db76d26fa9c54bea88bee66789c
Move delay driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I5e806bd0e0a0a4b436048513b7089db90ff9805f
Move console/scif driver code to common directory, so that the
same code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I0b15e4f4ffaaa99e77bcee32b1dad648eeadcd9b
Move pwrc driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I75d91a44d872fe2296b15c700efacd5721385363
Move io driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ic661e415c91a1fbfd5eee3bba86466037e51574b
Move eMMC driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I7f3055709337327d1a1c9f563c14ad1626adb355
Move plat common sources to common directory, so that same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Id2b1822c97cc50e3febaffc2e5f42b4d53809a17
Create a common directory and move the header and assembly files
so that the common code can be used by both Renesas R-Car Gen3 and
RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ia9a563a1c3c9f8c6f0d3cb82622deb2e155d7f6c
Write char if fifo is empty. If this is done like this all chars are
printed. Because origin code just put that chars to fifo and in case of
reset messages were missing.
Before this change chars are put to fifo and only check before adding if
fifo is full. The patch is changing this logic that it is adding char only
when fifo is empty to make sure that in case of reset (by another SW for
example) all chars are printed. Maybe one char can be missed but for IP
itself it is much easier to send just one char compare to full fifo.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Ic24c2c1252bce24be2aed68ee29477ca4a549e5f
This patch fixes checkpatch warnings and arrange header
as per TF-A coding style.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I46cd4d9b2851202324fe714e776cf3ad2ee1d923
Sort the headers alphabetically and replace TAB with a space
after #define.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I07c358294b7c02cbfa360112bbbde0eb5f2b50f5
This patches fixes checkpatch warnings, replace TAB with space
after #define macros and arrange header as per TF-A coding style.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Iba009587e0b499b3ae58876be390602ae14175b2
Fix checkpatch warnings.
There are no functional changes.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Iec7dd019bd38e84eccd8cc17189745fdef1911bb
This patch fixes the below checkpatch warnings
Line 13: WARNING: please, no spaces at the start of a line
Line 15: WARNING: please, no spaces at the start of a line
Line 18: WARNING: Missing a blank line after declarations
Line 24: WARNING: please, no spaces at the start of a line
Line 26: WARNING: please, no spaces at the start of a line
Line 29: WARNING: Missing a blank line after declarations
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I41d146e86889640d11e88c0717039353ddceff0d
Fix checkpatch warnings.
There are no functional changes.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ic7406aa88e121914270a8d192f170c9c4244578a
Use space instead of TAB after #define's. Also updated
header files as per TF-A coding style.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I4eac94f0bc79f24b8ac7165ec48f1e1de95d7205
Replace TAB with space after #define macros and update comments as per
TF-A coding style.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Iff46838a41f991f7dd9dc6fb043e9e482ea0b11d
Sort the header includes alphabetically, fix typos and drop unneeded TAB
and replace it with space
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I62e2658b0309c0985dd32ff023b8b16bd7f2be8e
Implementation is simple, just wait for the TX FIFO to be empty.
Without this patch TF-A on A3720 truncate the last line:
NOTICE: BL31: Built : 16:1
With this patch TF-A on A3720 print correctly also the last line:
NOTICE: BL31: Built : 19:03:31, Dec 23 2020
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I2f2ea42beab66ba132afdb400ca7898c5419db09
Fix checkpatch warnings and MISRA defects.
There are no functional changes.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I349a8eaa7bd6182746ba5104ee9fe48a709c24fd
The BL31 log driver is registered before the xlat tables are initialized,
at that point the log memory is configured as device memory and can only
be accessed with up-to-32bit aligned accesses. Adjust the driver to do
just that.
The memset() call has to be replaced by a loop of 32bit writes to the log,
the memcpy() is trivial to replace with a single 32bit write of the entire
TLOG word. In the end, this even simplifies the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Ie9152e782e67d93e7236069a294df812e2b873bf
* changes:
docs: update STM32MP1 with versions details
stm32mp1: get peripheral base address from a define
stm32mp1: add finished good variant in board identifier
Retrieve peripheral base address from a define instead of
parsing the device tree. The goal is to improve execution time.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I2588c53ad3d4abcc3d7fe156458434a7940dd72b
Usually, C has no problem up-converting types to larger bit sizes. MISRA
rule 10.7 requires that you not do this, or be very explicit about this.
This resolves the following required rule:
bl1/aarch64/bl1_context_mgmt.c:81:[MISRA C-2012 Rule 10.7 (required)]<None>
The width of the composite expression "0U | ((mode & 3U) << 2U) | 1U |
0x3c0U" (32 bits) is less that the right hand operand
"18446744073709547519ULL" (64 bits).
This also resolves MISRA defects such as:
bl2/aarch64/bl2arch_setup.c:18:[MISRA C-2012 Rule 12.2 (required)]
In the expression "3U << 20", shifting more than 7 bits, the number
of bits in the essential type of the left expression, "3U", is
not allowed.
Further, MISRA requires that all shifts don't overflow. The definition of
PAGE_SIZE was (1U << 12), and 1U is 8 bits. This caused about 50 issues.
This fixes the violation by changing the definition to 1UL << 12. Since
this uses 32bits, it should not create any issues for aarch32.
This patch also contains a fix for a build failure in the sun50i_a64
platform. Specifically, these misra fixes removed a single and
instruction,
92407e73 and x19, x19, #0xffffffff
from the cm_setup_context function caused a relocation in
psci_cpus_on_start to require a linker-generated stub. This increased the
size of the .text section and caused an alignment later on to go over a
page boundary and round up to the end of RAM before placing the .data
section. This sectionn is of non-zero size and therefore causes a link
error.
The fix included in this reorders the functions during link time
without changing their ording with respect to alignment.
Change-Id: I76b4b662c3d262296728a8b9aab7a33b02087f16
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Chip select is retrieved from device tree and check
must be done regarding the MAX_CS defined.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Reviewed-by: Christophe KERELLO <christophe.kerello@st.com>
Change-Id: I03144b133bd51a845a4794f0f6bbd9402fc04936
FMC node bindings are modified to add EBI controller node.
FMC driver and associated device tree files are modified
to support these new bindings.
Change-Id: I4bf201e96a1aca20957e0dac3a3b87caadd05bdc
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
In the function gicv2_set_spi_routing, the signed value proc_num is cast
to unsigned int before being compared to other unsigned values in two
assert calls. The value proc_num can be a negative value, and once the
negative value is cast to unsigned it becomes a very large number which
will trigger the assert. This patch changes the assert cast so that the
unsigned values are cast to signed instead, keeping the same functionality
but allowing proc_num to be negative.
This bug can be seen when running the SDEI RM_ANY routing mode test in
TFTF on the Juno platform.
This patch also makes the usage of the proc_num variable in other gicv2
functions more clear.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: If1b98eebb00bd9b73862e5e995e5e68c168170a6
And from crash_console_flush.
We ignore the error information return by console_flush in _every_
place where we call it, and casting the return type to void does not
work around the MISRA violation that this causes. Instead, we collect
the error information from the driver (to avoid changing that API), and
don't return it to the caller.
Change-Id: I1e35afe01764d5c8f0efd04f8949d333ffb688c1
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Clear interrupt flag register after each sector read to avoid
issue when checking the register status.
Without clearing the interrupt, the status read doesn't wait
properly the ready bit.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: If290e3f165b986f0e736bb1b5e4d3dad4b749d74
The polarity inversion for USB was not tested due to lack of hw design
which requires it. Currently all supported boards doesn't require USB
phy polarity inversion, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards. Enable the option for the ones that need it.
Change-Id: Ia5f2ee313a93962e94963e2dd8a759ef6d9da369
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The cp110 comphy has ability to invert RX and/or TX polarity. Polarity
depends on board design. Currently all supported boards doesn't require
SATA phy polarity invert, therefore COMPHY_POLARITY_NO_INVERT is set for
all boards.
Change-Id: Ifd0bc6aaf8a76a0928132b197422f3193cf020d5
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
According to erratum IPCE_COMPHY-1353 the TX_IDLE bit should
be toggled in addition to the XFI/SFI PHY reset.
Change-Id: Idd2c2abfcb2f960caa01e6d69db524c2e4734f50
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Do not force non-secure access level for PIDI masters when LLC_SRAM
is enabled. The EIP197 is located on CP0 and need to access secure
SRAM in AP LLC. This requires EIP197 DMA to have AXPROT[1]=0 and not
changed when forwarded to address decoding tables.
Change-Id: I8962db94a124350c14220ba6d0364d294ae4664a
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Added ccu window to allow access to addresses
in the range [0xf100_0000, 0xf1ff_ffff].
Change-Id: I63ee68338d674114d01cd627198dc907653493e8
Signed-off-by: Alex Leibovich <alexl@marvell.com>
This patch migrates the mbedcrypto dependency for TF-A
to mbedTLS repo v2.24.0 which is the latest release tag.
The relevant documentation is updated to reflect the
use of new version.
Change-Id: I116f44242e8c98e856416ea871d11abd3234dac1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
A GICv3 interrupt controller will be instantiated for a certain number
of cores. This will result in the respective number of GICR frames. The
last frame will have the "Last" bit set in its GICR_TYPER register.
For platforms with a topology unknown at build time (the Arm FPGAs, for
instance), we need to learn the number of used cores at runtime, to size
the GICR region in the devicetree accordingly.
Add a generic function that iterates over all GICR frames until it
encounters one with the "Last" bit set. It returns the number of cores
the GICv3 has been configured for.
Change-Id: I79f033c50dfc1c275aba7122725868811abcc4f8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
MCKPROT hardening in RCC mandates that both bits RCC[TZEN] and
RCC[MCKPROT] are enabled. This change fixes stm32mp1_rcc_is_mckprot()
to check both bits, not RCC[MCKPROT] only.
This change also updates stm32mp1_rcc_is_secure() for consistency.
Change-Id: If1f07babdcb5677906ddbf974d9dc17255d4e174
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The ICR static flags are cleared before sending a command.
The SDMMC_DCTRLR register is set to 0 if no data is expected on a given
command or on the next command in case of CMD55.
Change-Id: I5ae172a484218f53160e98b3684967c6960475a6
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The retries number should be 3.
A warning message is added in mmc_block_read(), and the code is refactored.
Change-Id: I577c7dd91c451c7580b1660042cb5fe26ee3fa12
Signed-off-by: Yann Gautier <yann.gautier@st.com>
nand_wait_ready is called with a millisecond delay
but the timeout used a micro second. Fixing the conversion
in the timeout call.
The prototype of the function is also changed to use an unsigned int
parameter.
Change-Id: Ia3281be7980477dfbfdb842308d35ecd8b926fb8
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change the detection message from WARN to INFO when macronix
NOR is detected.
Change-Id: I488696f1fb75b823e85decfcd6cd32e7b36a6c2e
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The call to fdt_get_status(node) has to be done after the DT is found
to be valid.
Fixes: 1fc2130c5 stm32mp1: update device tree and gpio functions
Change-Id: I70f803aae3dde128a9e740f54c8837b64cb1a244
Signed-off-by: Yann Gautier <yann.gautier@st.com>
While restarting a new hash computation, STR register
is not cleared. It needs to be written before each
computation.
Change-Id: If65902dd21f9c139ec5da3ca87721232f73710db
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Builds in Debug mode with Measured Boot enabled might run out of trusted
SRAM. This patch allows to change the Log Level at which the Measured Boot
driver will dump the event log, so the latter can be accessed even on
Release builds if necessary, saving space on RAM.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I133689e313776cb3f231b774c26cbca4760fa120
Loop macros make it easier for developers to include new variables to
assert or define and also help code code readability on makefiles.
Change-Id: I0d21d6e67b3eca8976c4d856ac8ccc02c8bb5ffa
Signed-off-by: Leonardo Sandoval <leonardo.sandoval@linaro.org>
The DRIVEVBUS power rail of the AXP803 PMIC is mostly used to supply
the USB bus power on micro USB sockets, when used in host mode. As this
is a dynamic operation, and mostly we want micro USB sockets to act in
client mode initially, BL31 should not actually enable this power line.
However, on some boards DRIVEVBUS is used to supply power to normal
USB-A sockets. Failing to activate this line there results in
non-functional USB in U-Boot on those boards.
For that reason we were enabling DRIVEVBUS so far, as it did not seem to
cause any harm to the other boards. However it turns out that on the
Pinephone (and other systems with a battery), actually enabling DRIVEVBUS
unconditionally causes serious problems (reboot loop).
To accommodate both use cases, without reverting to a build time option,
check the default OTG configuration in the devicetree. For boards with
USB-A sockets this is set to "host", on boards with micro-B sockets to
"otg". Depending on this setting, we either enable DRIVEVBUS or leave it
alone.
This fixes TF-A on the Pinephone and potentially other battery powered
devices.
Change-Id: Iec0e07f218b2b4393bf4e05c3386261f8ed19e9f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For dualroot CoT there are two sets of SP certificates, one owned by
Silicon Provider(SiP) and other owned by Platform. Each certificate can
have a maximum of 4 SPs.
This patch reduces the number of SiP owned SPs from 8 to 4 and adds
the remaining 4 to Plat owned SP.
Plat owned SP certificate is signed using Platform RoT key and
protected against anti-rollback using the Non-trusted Non-volatile
counter.
Change-Id: Idc3ddd87d6d85a5506a7435f45a6ec17c4c50425
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
ERRATA ID: RES-3033912 - Internal Address Space Init state causes
a hang upon accesses to [0xf070_0000, 0xf07f_ffff]
Workaround: Boot Firmware (ATF) should configure CCU_RGF_WIN(4) to
split [0x6e_0000, 0xff_ffff] to values [0x6e_0000, 0x6f_ffff] and
[0x80_0000, 0xff_ffff] that cause accesses to the segment of
[0xf070_0000, 0xf07f_ffff] to act as RAZWI. Reuse common
work-around code for both AP806 and AP807.
Change-Id: Ia91a4802d02917d1682faa0c81571093d1687d97
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Currently only single signing domain is supported for SP packages but
there is plan to support dual signing domains if CoT is dualroot.
SP_CONTENT_CERT_ID is the certificate file which is currently generated
and signed with trusted world key which in-turn is derived from Silicon
provider RoT key.
To allow dual signing domain for SP packages, other certificate file
will be derived from Platform owned RoT key.
This patch renames "SP_CONTENT_CERT_ID" to "SIP_SP_CONTENT_CERT_ID" and
does other related changes.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I0bc445a3ab257e2dac03faa64f46e36a9fed5e93
This patch fixes defects 10.3, 10.4, 10.7, 20.7
reported by MISRA-2012 scan and adds braces for
conditional statements according to the TF-A
coding style.
Change-Id: If84ed31cdd55bc8e7cdd2a5f48c0dacc25792112
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
* changes:
plat/arm/board/fvp: Add support for Measured Boot
TF-A: Add support for Measured Boot driver to FCONF
TF-A: Add support for Measured Boot driver in BL1 and BL2
TF-A: Add Event Log for Measured Boot
TF-A: Add support for Measured Boot driver
This patch adds support for Event Log generation required
for Measured Boot functionality.
Change-Id: I34f05a33565e6659e78499d62cc6fb00b7d6c2dc
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
The Arm GIC-Clayton IP has the same power management requirements as
the GIC-600, when it comes to powering up the redistributors before
using them.
Add the IIDR value to the existing list of implementations requiring
the power sequence.
Change-Id: Ib965dfe278c40a4fff94f65a8d445c27a2ae6fd2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch moves all GICv2 driver files into new added
'gicv2.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
NOTE: Usage of 'drivers/arm/gic/common/gic_common.c' file
is now deprecated and platforms with GICv2 driver need to
be modified to include 'drivers/arm/gic/v2/gicv2.mk' in
their makefiles.
Change-Id: Ib10e71bdda0e5c7e80a049ddce2de1dd839602d1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
The cause of failure is not memory shortage.
The comment for ENFILE in include/lib/libc/errno.h
/* Too many open files in system */
... is a better match to the warning message here.
Change-Id: I45a1740995d464edd8b3e32b93f1f92ba17e5874
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Fix the line address macro
- LLC invalidate and enable before ways lock for allocation
- Add support for limited SRAM size allocation
- Add SRAM RW test function
Change-Id: I1867ece3047566ddd7931bd7472e1f47fb42c8d4
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Since the AP process can be enabled on different setups, the information
about used comphy lane should be passed to AP FW. For instance:
- A8K development board uses comphy lane 2 for eth 0
- cn913x development board uses comphy lane 4 for eth 0
Change-Id: Icf001fb3eea4d9c24c09384e49844ecaf8655ad2
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Now when mg_conf_cm3 driver is present - move all relevant code there.
Change-Id: I444d9e877c450d6ee69ca3a49b547e4c3aeac0be
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
After configuring comphy to AP mode also start AP FW.
Change-Id: Ib28977d7ee643575a818ba17f69dea0b7e8e0df4
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Implement function which will allow to start AP FW.
Change-Id: Ie0fc8ad138bf56b10809cdc92d1e5e96a2aaf33f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The assignments to 'result' are unneeded.
Change-Id: I18899f10bf9bd7f219f0e47a981683d8b4701bde
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Register in the shared resources driver the secure or non-secure state
of the HASH instances. Note that only BL32 needs to register the
shared peripheral because BL2 does not embed the shared resources
driver.
Change-Id: I7f78fa8e47da71d48ef8b1dfe4d6f040fe918d8b
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Register in the shared resources driver the secure or non-secure state
of the GPIO pins.
Change-Id: Ifda473bcbbb0af799be6587961d6641edf887605
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Register in the shared resources driver the secure or non-secure state
of the IWDG instances.
Change-Id: I3a3bc9525447f6a2a465891ca3a3fd5fe664ca07
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Register in the shared resources driver the secure or non-secure
state of the PMIC.
Change-Id: Ic1f172ba62785018f8e9bb321782d725e2d2f434
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Introduce stm32mp1_register_clock_parents_secure() in stm32mp1
clock driver to allow platform shared resources to register as
secure the parent clocks of a clock registered as secure.
Change-Id: I53a9ab6aa78ee840ededce67e7b12a84e08ee843
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
This patch adds the IIDR value for GIC600-AE to the gicv3_is_gic600()
helper function. This helps platforms supporting this version of the
GIC600 interrupt controller to function with the generic GIC driver.
Verified with tftf-validation test suite
******************************* Summary *******************************
> Test suite 'Framework Validation'
Passed
> Test suite 'Timer framework Validation'
Passed
=================================
Tests Skipped : 0
Tests Passed : 6
Tests Failed : 0
Tests Crashed : 0
Total tests : 6
=================================
NOTICE: Exiting tests.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I518ae7b56f7f372e374e453287d76ca370fc3574
* changes:
plat: marvell: armada: a8k: add OP-TEE OS MMU tables
drivers: marvell: add support for mapping the entire LLC to SRAM
plat: marvell: armada: add LLC SRAM CCU setup for AP806/AP807 platforms
plat: marvell: armada: reduce memory size reserved for FIP image
plat: marvell: armada: platform definitions cleanup
plat: marvell: armada: a8k: check CCU window state before loading MSS BL2
drivers: marvell: add CCU driver API for window state checking
drivers: marvell: align and extend llc macros
plat: marvell: a8k: move address config of cp1/2 to BL2
plat: marvell: armada: re-enable BL32_BASE definition
plat: marvell: a8k: extend includes to take advantage of the phy_porting_layer
marvell: comphy: initialize common phy selector for AP mode
marvell: comphy: update rx_training procedure
plat: marvell: armada: configure amb for all CPs
plat: marvell: armada: modify PLAT_FAMILY name for 37xx SoCs
Cleaned up confused naming between TB_FW and FW_CONFIG.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I9e9f6e6ca076d38fee0388f97d370431ae067f08
* changes:
drivers/scmi-msg: smt entry points for incoming messages
drivers/scmi-msg: support for reset domain protocol
drivers/scmi-msg: support for clock protocol
drivers/scmi-msg: driver for processing scmi messages
It is desired to have the peripheral writes completed to clear the
interrupt condition and de-assert the interrupt request to GIC before
EOI write. Failing which spurious interrupt will occurred.
A barrier is needed to ensure peripheral register write transfers are
complete before EOI is done.
GICv2 memory mapped DEVICE nGnR(n)E writes are ordered from core point
of view. However these writes may pass over different interconnects,
bridges, buffers leaving some rare chances for the actual write to
complete out of order.
GICv3 ICC EOI system register writes have no ordering against nGnR(n)E
memory writes as they are over different interfaces.
Hence a dsb can ensure from core no writes are issued before the previous
writes are *complete*.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Change-Id: Ie6362009e2f91955be99dca8ece14ade7b4811d6
Add llc_sram_enable() and llc_sram_disable() APIs to Marvell
cache_lls driver.
Add LLC_SRAM definition to Marvell common makefile - disabled
by the default.
Add description of LLC_SRAM flag to the build documentation.
Change-Id: Ib348e09752ce1206d29268ef96c9018b781db182
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add ccu_is_win_enabled() API for checking the CCU window
state using AP and window indexes.
Change-Id: Ib955a2cac28b2729b0a763f3bbbea28b476a2fe4
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Make all LLC-related macros to start with the same prefix
Add more LLC control registers definitions
This patch is a preparation step for LLC SRAM support
Change-Id: I0a4f0fc83e8ef35be93dd239a85f2a9f88d1ab19
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Configuring common phy selector which was missing for AP mode.
Change-Id: I15be1ba50b8aafe9094734abec139d72c18bb224
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
1) Relay only on rx training, remove parts responsible for tx training
(trx training).
2) Add extra steps e.g. preconfigure FFE before starting training.
3) Remove some unnecessary steps like RRBS31 loopback setting which
shouldn't be relevant for tx_training.
Change-Id: Ib1e8567714f9ce33578186a262c339aa4b1c51f2
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble: ap807: clean-up PLL configuration sequence
ddr: a80x0: add DDR 32-bit mode support
plat: marvell: mci: perform mci link tuning for all mci interfaces
plat: marvell: mci: use more meaningful name for mci link tuning
plat: marvell: a8k: remove wrong or unnecessary comments
plat: marvell: ap807: enable snoop filter for ap807
plat: marvell: ap807: update configuration space of each CP
plat: marvell: ap807: use correct address for MCIx4 register
plat: marvell: add support for PLL 2.2GHz mode
plat: marvell: armada: make a8k_common.mk and mss_common.mk more generic
marvell: armada: add extra level in marvell platform hierarchy
This change implements SCMI channels for reading a SCMI message from a
shared memory and call the SCMI message drivers to route the message
to the target platform services.
SMT refers to the shared memory management protocol which is used
to get/put message/response in shared memory. SMT is a 28byte header
stating shared memory state and exchanged protocol data.
The processing entry for a SCMI message can be a secure interrupt
or fastcall SMCCC invocation.
SMT description in this implementation is based on the OP-TEE
project [1] itself based in the SCP-firmware implementation [2].
Link: [1] a58c4d706d
Link: [2] https://github.com/ARM-software/SCP-firmware.git
Change-Id: I416c7dab5c67954c6fe80bae8d8cdfdcda66873e
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Adds SCMI reset domain protocol support in the SCMI message drivers
as defined in SCMI specification v2.0 [1]. Not all the messages
defined in the specification are supported.
scmi_msg_get_rd_handler() sanitizes the message_id value
against any speculative use of reset domain ID as a index since by
SCMI specification, IDs are indices.
This implementation is based on the OP-TEE project implementation [2]
itself based on the SCP-firmware implementation [3] of the SCMI
protocol server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] 56a1f10ed9
Link: [3] https://github.com/ARM-software/SCP-firmware.git
Change-Id: If7cf13de40a815dedb40dcd5af8b6bb6725d9078
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Adds SCMI clock protocol support in the SCMI message drivers as
defined in SCMI specification v2.0 [1] for clock protocol messages.
Platform can provide one of the plat_scmi_clock_*() handler for the
supported operations set/get state/rate and others.
scmi_msg_get_clock_handler() sanitizes the message_id value
against any speculative use of clock ID as a index since by
SCMI specification, IDs are indices.
This implementation is based on the OP-TEE project implementation [2]
itself based on the SCP-firmware implementation [3] of the SCMI
protocol server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] a7a9e3ba71
Link: [3] https://github.com/ARM-software/SCP-firmware.git
Change-Id: Ib56e096512042d4f7b9563d1e4181554eb8ed02c
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
This change introduces drivers to allow a platform to create a basic
SCMI service and register handlers for client request (SCMI agent) on
system resources. This is the first piece of the drivers: an entry
function, the SCMI base protocol support and helpers for create
the response message.
With this change, scmi_process_message() is the entry function to
process an incoming SCMI message. The function expect the message
is already copied from shared memory into secure memory. The message
structure stores message reference and output buffer reference where
response message shall be stored.
scmi_process_message() calls the SCMI protocol driver according to
the protocol ID in the message. The SCMI protocol driver will call
defined platform handlers according to the message content.
This change introduces only the SCMI base protocol as defined in
SCMI specification v2.0 [1]. Not all the messages defined
in the specification are supported.
The SCMI message implementation is derived from the OP-TEE project [2]
itself based on the SCP-firmware implementation [3] of the SCMI protocol
server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] ae8c806809
Link: [3] https://github.com/ARM-software/SCP-firmware/tree/v2.6.0
Change-Id: I639c4154a39fca60606264baf8d32452641f45e9
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
with sha 44f1aa8, support for Silicon Provider(SiP) owned Secure
Partition(SP) was added for dualroot CoT. This patch extends this
support for tbbr CoT.
Earlier tbbr CoT for SPs was left to avoid adding new image types in
TBBR which could possibly be seen as deviation from specification.
But with further discussions it is understood that TBBR being a
*minimal* set of requirements that can be extended as long as we don't
violate any of the musts, which is the case with adding SP support.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I1b9e3ebdd7d653f1fd4cc3bd910a69871b55ecbb
The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.
This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.
Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
A new certificate "sip-sp-cert" has been added for Silicon Provider(SiP)
owned Secure Partitions(SP). A similar support for Platform owned SP can
be added in future. The certificate is also protected against anti-
rollback using the trusted Non-Volatile counter.
To avoid deviating from TBBR spec, support for SP CoT is only provided
in dualroot.
Secure Partition content certificate is assigned image ID 31 and SP
images follows after it.
The CoT for secure partition look like below.
+------------------+ +-------------------+
| ROTPK/ROTPK Hash |------>| Trusted Key |
+------------------+ | Certificate |
| (Auth Image) |
/+-------------------+
/ |
/ |
/ |
/ |
L v
+------------------+ +-------------------+
| Trusted World |------>| SiP owned SPs |
| Public Key | | Content Cert |
+------------------+ | (Auth Image) |
/ +-------------------+
/ |
/ v|
+------------------+ L +-------------------+
| SP_PKG1 Hash |------>| SP_PKG1 |
| | | (Data Image) |
+------------------+ +-------------------+
. .
. .
. .
+------------------+ +-------------------+
| SP_PKG8 Hash |------>| SP_PKG8 |
| | | (Data Image) |
+------------------+ +-------------------+
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ia31546bac1327a3e0b5d37e8b99c808442d5e53f
Update PLL configuration according to HW team guidelines.
Change-Id: I23cac4fb4a638e7416965a5399ce6947e08d0711
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Remove pll powerdown from pll configuration sequence to improve
stability. Remove redundant cases, which no longer exist.
Also get rid of irrelevant definition of CPU_2200_DDR_1200_RCLK_1200,
which is not used by 806/807.
Change-Id: If911e7dee003dfb9a42fafd7ffe34662f026fd23
Signed-off-by: Alex Leibovich <alexl@marvell.com>
This commit introduces two changes:
- remove hardcoded references to mci0 from the driver
- perform mci optimization for all mci interfaces
It fixes performance issues observed on cn9132 CP2.
Change-Id: I4e040cd54ff95c9134035ac89b87d8feb28e9eba
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The mci_initialize function name was misleading. The function itself
doesn't initialize MCI in general but performs MCI link tuning for
performance improvement.
Change-Id: I13094ad2235182a14984035bbe58013ebde84a7e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
By default all external CPs start with configuration address space set to
0xf200_0000. To overcome this issue, go in the loop and initialize the
CP one by one, using temporary window configuration which allows to access
each CP and update its configuration space according to decoding
windows scheme defined for each platform.
In case of cn9130 after this procedure bellow addresses will be used:
CP0 - f2000000
CP1 - f4000000
CP2 - f6000000
When the re-configuration is done there is need to restore previous
decoding window configuration(init_io_win).
Change-Id: I1a652bfbd0bf7106930a7a4e949094dc9078a981
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
The AP807 uses different register offset for MCIx4 register, reflect it
in the code.
Change-Id: Ic7e44fede3c69083e8629741e7c440b1ae08c35f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
plat, include/plat) are moved to the new "armada" sub-folder.
Change-Id: Icf03356187078ad6a2e56c9870992be3ca4c9655
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
ETZPC stands for Extended TrustZone Protection Controller. It is a
resource conditional access device. It is mainly based on Arm TZPC.
ST ETZPC exposes memory mapped DECPROT cells to set access permissions
to SoC peripheral interfaces as I2C, SPI, DDR controllers, and some
of the SoC internal memories.
ST ETZPC exposes memory mapped TZMA cells to set access permissions
to some SoC internal memories.
Change-Id: I47ce20ffcfb55306dab923153b71e1bcbe2a5570
Co-developed-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
This patch enables the stream ID for the SD/MMC
controllers via dedicated unit register. Thanks to this
change it is possible to configure properly the
IOMMU in OS and use the SD/MMC interface in a guest
Virtual Machine.
Change-Id: I99cbd2c9882eb558ba01405d3d8a3e969f06e082
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Changes stm32mp1 reset driver to API to add a timeout argument
to stm32mp_reset_assert() and stm32mp_reset_deassert() and
a return value.
With a supplied timeout, the functions wait the target reset state
is reached before returning. With a timeout of zero, the functions
simply load target reset state in SoC interface and return without
waiting.
Helper functions stm32mp_reset_set() and stm32mp_reset_release()
use a zero timeout and return without a return code.
This change updates few stm32 drivers and plat/stm32mp1 blé_plat_setup.c
accordingly without any functional change.
functional change.
Change-Id: Ia1a73a15125d3055fd8739c125b70bcb9562c27f
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
CoT used for BL1 and BL2 are moved to tbbr_cot_bl1.c
and tbbr_cot_bl2.c respectively.
Common CoT used across BL1 and BL2 are moved to
tbbr_cot_common.c.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I2252ac8a6960b3431bcaafdb3ea4fb2d01b79cf5
Adds missing terminal new line character '\n' to debug traces,
fix format as index is an unsigned value and use present tense rather
than past tense in the printed message.
Change-Id: I88c06ef4d3a11d97ff8e96875a3dd0f58a3c98b6
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Heyi Guo
Madhukar Pappireddy
Manish Pandey
Peng Fan
Pali Rohár
Biju Das
Michal Simek
Marek Vasut
Joanna Farley
Mark Dykes
Yann Gautier
Jimmy Brisson
Lionel Debieve
Christophe Kerello
johpow01
Grzegorz Jaszczyk
Marcin Wojtas
Konstantin Porotchkin
Alex Leibovich
Alexei Fedorov
Andre Przywara
Etienne Carriere
Javier Almansa Sobrino
Leonardo Sandoval
Stefan Chulski
Bharat Gooty
Masahiro Yamada
Varun Wadekar
Manish V Badarkhe
Louis Mayencourt
Sandeep Tripathy
Etienne Carriere