Add the read data eye training = training for optimal read valid placement
(RVTRN) when the built-in calibration is executed for LPDDR2 and LPDDR3.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Change-Id: I7ac1c77c21ebc30315b532741f2f255c2312d5b2
The support of a predefined DDR PHY tuning result is removed for
STM32MP1 driver because it is not needed at the supported frequency
when built-in calibration is executed.
The calibration parameters were provided in the device tree by the
optional node "st,phy-cal", activated in ddr helper file by the
compilation flag DDR_PHY_CAL_SKIP and filled with values generated
by CubeMX.
This patch
- updates the binding file to remove "st,phy-cal" support
- updates the device trees and remove the associated defines
- simplifies the STM32MP1 DDR driver and remove the support of
the optional "st,phy-cal"
After this patch the built-in calibration is always executed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Change-Id: I3fc445520c259f7f05730aefc25e64b328bf7159
Replace %d with %u in logs, to avoid warning when
-Wformat-signedness is enabled.
And correct the order of includes.
Change-Id: I7c711a37fc1deceb8853831a8a09ae50422859c9
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
The issue was reported by Coverity [1]. The return of the functions
regulator_disable() and regulator_enable() was not checked.
If they fail, this means there is an issue either with PMIC or I2C.
The board should the stop booting with a panic().
[1] https://scan4.scan.coverity.com/reports.htm#v47771/p11439/mergedDefectId=374565
Change-Id: If5dfd5643c210e03ae4b1f4cab0168c0db89f60e
Signed-off-by: Yann Gautier <yann.gautier@st.com>
For somewhat historical reasons we are doing some initial PMIC regulator
setup in BL31, as U-Boot does not (yet) have a PMIC driver. This worked
fine so far, but there is at least one board (OrangePi 3) that gets upset,
because the Ethernet PHY needs some *coordinated* bringup of *two*
regulators.
To avoid custom hacks, let's introduce a build option to keep doing the
regulator setup in TF-A. Defining SUNXI_SETUP_REGULATORS to 0 will break
support for some devices on some boards in U-Boot (Ethernet and HDMI),
but will allow to bring up the OrangePi 3 in Linux correctly. We keep
the default at 1 to not change the behaviour for all other boards.
After U-Boot gained proper PMIC support at some point in the future, we
will probably change the default to 0, to get rid of the less optimal
PMIC code in TF-A.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Change-Id: Ie8e2583d0396f6eeaae8ffe6b6190f27db63e2a7
To correctly initialize the MMC devices, a power cycle is required.
For this we need to:
- disable vmmc-supply regulator
- make the power cycle required for SDMMC2 peripheral
- enable regulators
Change-Id: I2be6d9082d1cc4c864a82cf2c31ff8522e2d31a2
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Fixed regulator is mainly used when no pmic is available
Change-Id: Ib6a998684bcb055ba95a093bee563372d9051474
Signed-off-by: Pascal Paillet <p.paillet@st.com>
print_pmic_info_and_debug() prints the PMIC version ID and displays
regulator information if debug is enabled.
It is under DEBUG flag and called after initialize_pmic() in BL2.
Change-Id: Ib81a625740b7ec6abb49cfca05e44c69efaa4718
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Add a regulator framework to:
- provide an interface to consumers and drivers,
- connect consumers with drivers,
- handle most of devicetree-parsing,
- handle always-on and boot-on regulators,
- handle min/max voltages,
Change-Id: I23c939fdef2c71a416c44c9de332f70db0d2aa53
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Add support for ICC, sink mode, bypass mode,
active discharge and list voltages.
Handle LDO3 sink source mode in a different way to avoid
setting voltage while in sink source mode.
Change-Id: Ib1b909fd8a153f542917f650e43e24317a570534
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Add regulators boost, pwr_sw1 and pwr_sw2 regulators related to
USB OTG supply BOOST, SW_OTG and SWIN/SWOUT. These regulators are
needed since manipulated during the suspend/resume power sequence
as per FDT description for stm32mp15x-xxx boards from
STMicroelectronics.
Change-Id: I6217de707e49882bd5a9100db43e0d354908800d
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Store status of dt_pmic_status() as local static variable,
this avoids parsing DT several times.
In the same way, store nodes in dt_pmic_i2c_config() and
in dt_get_pmic_node() as local static variables.
Change-Id: I4585e9dfdde2847a369bffcc6f2b39ecc2b74de1
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
This is mainly a clock interface with clk_ops callbacks.
Those callbacks are: enable, disable, get_rate, set_parent,
and is_enabled.
This framework is compiled for STM32MP1.
Change-Id: I5119a2aeaf103ceaae7a60d9e423caf0c148d794
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Add set_gpio_reset_cfg() to set a pin in its reset configuration:
analog, no-pull, speed low, and its secure configuration, thanks to
stm32_gpio_is_secure_at_reset().
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I7b73c3636859f97fcc57f81cf68b42efc727922e
The constants BUNDLE_PERIOD_SCALE and PLL_READY_DLY refer to two
multi-bit registers within the Clock Source Low register. These
constants are used as masks for those registers (and values are not
defined since we are writing zeros to them).
Give them the _MASK suffix.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Id469d0ab4c755d2d6a0150a1ade33dd9d0293667
The register at offset 0x1C3 is called Clock Source Low in functional
specification, but we use constant name GLOB_CLK_SRC_LO. Rename it to
RST_CLK_CTRL instead.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: If7ca460cb166f3828678e1e09c4e6caf5bb77770
The register at offset 0x1C1 is called Reset and Clock Control in
functional specification, but we use constant name GLOB_PHY_CTRL0.
Rename it to RST_CLK_CTRL instead.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I5dac8913bd0686d4f5bd74b91cb7d07ba06df72b
Rename the Lane Status 1 register constants from LANE_STATUS1 to
LANE_STAT1, to use an abbreviation similar to that for Lane
Configuration registers (where we use LANE_CFGx instead of LANE_CONFIGx
or LANE_CONFIGURATIONx).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Ie329d5a93615efe261802a2f027475b602a5c840
Rename the Miscellaneous Control register constants from MISC_REGx to
MISC_CTRLx.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I4d43bbda44b090de4ecf2d52cfc468f9683cc3b5
According to the functional specification, the register at offset 0x48
is called Idle Sync Enable, not Unit Control or some such.
Rename the constants.
Only bit 12 of this register is defined, all other bits are reserved.
But for some reason the code needs the default value of the other bits,
so we also rename constant UNIT_CTRL_DEFAULT_VALUE to
IDLE_SYNC_EN_DEFAULT_VALUE.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Ia4f80f945a8f31c190cd9a1875d50d892e72825f
Generation Settings registers have the same layout for different
generations and same setting (i.e. Generation 2 Settings 2 register has
the same layout as Generation 3 Settings 2).
So it does not make sense to prefix the constants for Settings 2 with
G3.
Instead change the prefixes to GSx_ for settings register x.
For Settings 2 of Gen 2 and Gen 3 we have some definitions in the first
and some in the second. Move them all to the first defined register (in
this case Gen 2, since the constant for Gen 1 is not defined because it
is not used).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I15c337eb58aa37fd99fe388fd59373aa325a3a92
Sometimes we call the constants GENx_SET_y, sometimes GENx_SETTINGS_y,
and sometimes GENx_SETTING_y.
Unify this into GENx_SETy.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I3810fb52b2897fe6730ef6e58d434c47cfef14a9
COMPHY register addresses are defined twice
- once for indirect access, where the constants are of the form
COMPHY_<register_name>
- once for direct access, with constants of the form
<register_name>_ADDR
But sometimes the first case also has this _ADDR suffix (and other times
not).
Drop it from those places to unify how we define these registers.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Ibf95be8ade231d0e42258f40614a5f0974d280bd
Some register constants are defined with _REG suffix or REG_ prefix, but
others are not. Unify this by dropping these prefixes / suffixes.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I1ba331c0a4686093ee250bcaf3297349956ac9a8
The COMPHY_RESERVED_REG (offset 0x0E) is currently defined between
COMPHY_KVCO_CAL_CTRL (0x02) and COMPHY_DIG_LOOPBACK_EN (0x23).
But this register does not come from PHY lane register space. The
address 0x0E is not relative to PHY lane registers base address.
It only exists in the indirect register space, before PHY lane 2
registers (which start at address 0x200).
Move its definition in the header and add a comment.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Ie726384b980ace83d8ea327df09d928db74c2ab7
Move the definitions for the Miscellaneous Control 0 register (offset 0x4F),
to leave the registers sorted according to their offsets.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I9864be5bd00181d21c9334219be4f89c4f032c8b
The register name for the value PHY_GEN_USB3_5G is PHY_GEN_MAX. We
already define the mask constant as PHY_GEN_MAX_MASK. Thus also the
value name should be prefixed with PHY_GEN_MAX_.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Ibf72a66d2e65e240ed2cdbc3a301dbd793e2cb34
The register at offset 0x23 is called Digital Loopback Enable, but the
constant is COMPHY_LOOPBACK_REG0, as if there were some LOOPBACK_REG1
register or something, which there is not.
Rename the constant to COMPHY_DIG_LOOPBACK_EN.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Ie88bdd864e2c9ab7e8de70ed7f3a13ee8f08ff79
Currently reg_set() and reg_set16() are implemented via
mmio_clrsetbits_32(), meaning that first bits from mask are cleared,
then data bits are set.
But these function are used everywhere according to update semantics,
where only those bits that are in mask are allowed to be changed.
Example from phy-comphy-cp110.c
mask = HPIPE_RST_CLK_CTRL_PIPE_RST_MASK;
data = 0x1 << HPIPE_RST_CLK_CTRL_PIPE_RST_OFFSET;
/* Set PHY datapath width mode for V0 */
mask |= HPIPE_RST_CLK_CTRL_FIXED_PCLK_MASK;
data |= 0x0 << HPIPE_RST_CLK_CTRL_FIXED_PCLK_OFFSET;
/* Set Data bus width USB mode for V0 */
mask |= HPIPE_RST_CLK_CTRL_PIPE_WIDTH_MASK;
data |= 0x0 << HPIPE_RST_CLK_CTRL_PIPE_WIDTH_OFFSET;
/* Set CORE_CLK output frequency for 250Mhz */
mask |= HPIPE_RST_CLK_CTRL_CORE_FREQ_SEL_MASK;
data |= 0x0 << HPIPE_RST_CLK_CTRL_CORE_FREQ_SEL_OFFSET;
reg_set(hpipe_addr + HPIPE_RST_CLK_CTRL_REG, data, mask);
Change the implementation to update semantics by anding data with mask.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Ic72a8f64916274e08baef0b3f4c44a4fa07c1a6c
Currently reg_set() and reg_set16() are almost everywhere (both in
phy-comphy-3700.c and phy-comphy-cp110.c) used as if the semantics were
that of register update function (only bits that are set in mask are
updated):
reg_set(addr, data, mask) {
*addr = (*addr & ~mask) | (data & mask);
}
This comes both from names of arguments (data and mask), and from usage.
But both functions are in fact implemented via mmio_clrsetbits_32(), so
they actually first clear bits from mask and then set bits from data:
reg_set(addr, data, mask) {
*addr = (*addr & ~mask) | data;
}
There are only two places where this is leveraged (where some bits are
put into data argument but they are not put into the mask argument).
Fix those two usages to allow to convert the implementation from
clrsetbits semantics to update semantics.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Ib29a1dd7edcdee7a39c4752dbc9dfcd600d8cb5c
The comments about selector register values are wrong.
Bit 0 configures only lane 1, bit 4 only lane 0, and bit 8 lanes 0 and
2.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Iffe42374f92654ebe570557e0d462204439cfa31
Fix comment about COMPHY status register. PCIe/GbE0 PHY is on lane 1,
while USB3/GbE1 on lane 0.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I24734a61727d56f6eab2ed1c366d7a1810dbe19d
The current definitions of reference clock speed register values
#define PCIE_REF_CLOCK_SPEED_25M REF_CLOCK_SPEED_30M
#define USB3_REF_CLOCK_SPEED_25M REF_CLOCK_SPEED_30M
is ambiguous. The name of the constant implies 25 MHz, but the value
implies 30 MHz, which may make the reader think that the setting has
something to do with both values.
In reality, the values have different tables for SerDes and PCIe/USB3
PHY mode. The value for 25 MHz for PCIe/USB3 mode (0x2) is the value
for 30 MHz for SerDes mode.
Instead of defining the PCIe/USB3 constants relative to SerDes
constants, define them with absolute values, thus making it a little bit
more obvious that different modes have different value tables.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I50c66c6bbe22b9a9bec4685600cb8560524a643c
The MODE_REFDIV constant is only used as mask of the MODE_REFDIV
register, but we already have MODE_REFDIV_MASK constant for that.
Drop MODE_REFDIV.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: Icabb32189a7ca1a857dcf86cf0846bd0335f75d0
Constants SD_SPEED_1_25_G and SD_SPEED_2_5_G refer to SerDes frequency,
which is 1.25x that of data rate, since 1000base-x and 2500base-x use
the 8b/10b encoding:
mode frequency data rate
1000base-x 1.25 GHz 1 Gbps
2500base-x 3.125 GHz 2.5 Gbps
But the first constant refers to the frequency, while the second to the
data rate, which does not make sense.
Since the values in the specification refer to frequency, change the
name of the constant SD_SPEED_2_5_G to SD_SPEED_3_125_G to also refer to
the frequency, as SD_SPEED_1_25_G does.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I7670b45fa685aff93b3cafd84cf30d93620d8da1
According to Functional Specification, the common PHY register at offset
0x3f is actually Generation 3 Setting 2, while the register at offset
0x112 is Generation 2 Setting 3.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I4626672cbee2d08da1da7839a3cf3f90e78fa101
According to Functional Specification, the register at bit 1 of PHY
Configuration 1 is called PIN_PU_IVREF, not PIN_PU_IVEREF. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I912fa4a1956bf0b1b35a24925db03e3dbbe1adf3
When tf-a is built with the llvm toolchain, the compiler optimizes the
variable in some way which results in SCMI_MSG_GET_TOKEN assert failure
in multiple places. This patch makes the msg_header variable in
mailbox_mem struct volatile, which seems to fix the issue.
Signed-off-by: sahil <sahil@arm.com>
Change-Id: I1d28b30a6472fc23ed85adff9cf73dfb536e39cc
It doesn't look correct to use mbed TLS defines directly in the Event
Log driver as this driver may use another Crypto library in future.
Hence mbed TLS Crypto dependency on Event Log driver is removed by
introducing generic Crypto defines and uses those in the Event Log
driver to call Crypto functions.
Also, updated mbed TLS glue layer to map these generic Crypto defines
to mbed TLS library defines.
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ibc9c751f60cbce4d3f3cf049b7c53b3d05cc6735
Nicolas Le Bayon
Patrick Delaunay
Yann Gautier
Yann Gautier
André Przywara
Madhukar Pappireddy
Pascal Paillet
Etienne Carriere
Gabriel Fernandez
Manish Pandey
Marek Behún
sah01
Manish V Badarkhe
Sandrine Bailleux