The old API is deprecated and will eventually be removed.
Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.
The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.
Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.
The size reserved for BL2 has been increased.
Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
NXP's i.MX8QM is an ARMv8 SoC with 2 clusters, 2 Cortex-A72
cores in one cluster and 4 Cortex-A53 in the other cluster,
and also has system controller (Cortex-M4) inside, documentation
can be found in below link:
https://www.nxp.com/products/processors-and-microcontrollers/
applications-processors/i.mx-applications-processors/i.mx-8-processors:IMX8-SERIES
This patch adds support for booting up SMP linux kernel (v4.9).
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
NXP's i.MX8QX is an ARMv8 SoC with 4 Cortex-A35 cores and
system controller (Cortex-M4) inside, documentation can
be found in below link:
https://www.nxp.com/products/processors-and-microcontrollers/
applications-processors/i.mx-applications-processors/i.mx-8-processors:IMX8-SERIES
This patch adds support for booting up SMP linux kernel (v4.9).
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
NXP's i.MX8 SoCs have system controller (M4 core)
which takes control of clock management, power management,
partition management, PAD management etc., other
clusters like Cortex-A35 can send out command via MU
(Message Unit) to system controller for clock/power
management etc..
This patch adds basic IPC(inter-processor communication) support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Having these definitions in board_arm_def.h forces to
all the arm platforms to use the same definition for
PLAT_ARM_MEM_PROT_ADDR.
This macro also enables the mem-protect mechanism,
which means that all the arm platform has enabled
mem-protect and they cannot get rid of it.
Change-Id: Id29d2c51cbe6edc15f010a9f5a20c42266c48a08
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
In Arm platforms, when using dynamic configuration, the necessary
parameters are made available as a DTB. The DTB is loaded by BL1 and,
later on, is parsed by BL1, BL2 or even both, depending on when
information from the DTB is needed.
When the DTB is going to be parsed, it must be validated first, to
ensure that it is properly structured. If an invalid DTB is detected
then:
- BL1 prints a diagnostic but allows execution to continue,
- BL2 prints a diagnostic and panics.
Now the behaviour of BL1 is changed so for it also to panic. Thus, the
behaviour of BL1 and BL2 is now similar.
Keep in mind that if BL1 only loads the DTB but it doesn't need to
read/write it, then it doesn't validate it. The validation is done only
when the DTB is actually going to be accessed.
Change-Id: Idcae6092e6dbeab7248dd5e041d6cbb7784fe410
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>
Some peripherals are TrustZone aware, so they need to be configured to
be accessible from non-secure world, as we don't need any of them being
exclusive to the secure world.
This affects some clocks, DMA channels and the Secure Peripheral
Controller (SPC). The latter controls access to most devices, but is not
active unless booting with the secure boot fuse burnt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The reset vector entry point is preserved across CPU resets, so it only
needs to be set once at boot.
Hotplugged CPUs are not actually powered down, but are put in a wfi with
the GIC disconnected.
With this commit, Linux is able to enable, hotplug and use all four CPUs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
sun50i_cpu_on will be used by the PSCI implementation to initialize
secondary cores for SMP. Unfortunately, sun50i_cpu_off is not usable by
PSCI directly, because it is not possible for a CPU to use this function
to power itself down. Power cannot be shut off until the outputs are
clamped, and MMIO does not work once the outputs are clamped.
But at least CPU0 can shutdown the other cores early in the BL31 boot
process and before shutting down the system.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Allwinner A64 SoC is quite popular on single board computers.
It comes with four Cortex-A53 cores in a singe cluster and the usual
peripherals for set-top box/tablet SoC.
The ATF platform target is called "sun50i_a64".
[Andre: adapted to amended directory layout, removed unneeded definitions ]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This platform supports Allwinner's SoCs with ARMv8 cores. So far they
all sport a single cluster of Cortex-A53 cores.
"sunxi" is the original code name used for this platform, and since it
appears in the Linux kernel and in U-Boot as well, we use it here as a
short file name prefix and for identifiers.
This port includes BL31 support only. U-Boot's SPL takes the role of the
primary loader, also doing the DRAM initialization. It then loads the
rest of the firmware, namely ATF and U-Boot (BL33), then hands execution
over to ATF.
This commit includes the basic platform code shared across all SoCs.
There is no platform.mk yet.
[Andre: moved files into proper directories, supported RESET_TO_BL31,
various clean ups and simplifications ]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Remove the redundant SGI functions which map memory
for BL1 and BL2.
Change-Id: I651a06d0eb6d28263a56f59701bb3815f1ba93dc
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Append a node to hw-config dtb which will include a property to hold
the value of the SSC_VERSION register. This will be used by the BL33
stage to determine the platform-id and the config-id of the platform
it is executing on.
Change-Id: Ie7b1e5d8c1bbe0efdb7ef0714f14b7794ec6058e
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Remove the existing method of populating the platform id in arg2 of
BL33 which is no longer needed with dynamic configuration feature
enabled as the BL33 will get this information directly via the config
files. Add the tb_fw_config and hw_config dts files.
Change-Id: I3c93fec2aedf9ef1f774a5f0969d2d024e47ed2c
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
RFC4122 defines that fields are stored in network order (big endian),
but TF-A stores them in machine order (little endian by default in TF-A).
We cannot change the future UUIDs that are already generated, but we can store
all the bytes using arrays and modify fiptool to generate the UUIDs with
the correct byte order.
Change-Id: I97be2d3168d91f4dee7ccfafc533ea55ff33e46f
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
The stdint header was introduced to rk3399's plat_sip_calls.c in order
to fix missing stdint definitions. However, ordering headers
alphabetically caused the fix to be ineffective, as stint was then
included after the offending header file (dfs.h).
Move the stdint include to that header to properly fix the issue.
Change-Id: Ieaad37a7932786971488ab58fc5b169bfa79e197
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The translation tables allocated for the Secure Partition do not need
to be treated as a special case. They can be put amongst the other
tables mapping BL31's general purpose memory. They will be mapped with
the same attributes as them, which is fine.
The explicit alignment constraint in BL31's linker script to pad the
last page of memory allocated to the Secure Partition's translation
tables is useless too, as page tables are per se pages, thus their
end address is naturally aligned on a page-boundary.
In fact, this patch does not change the existing behaviour. Since
patch 22282bb68a ("SPM: Move all SP-related info to SP context
struct"), the secure_partition.c file has been renamed into sp_xlat.c
but the linker script has not been properly updated. As a result, the
SP translation tables are not specifically put at the start of the
xlat_table linker section, the __SP_IMAGE_XLAT_TABLES_START__/_END__
symbols have the same value, the size of the resulting mmap_region
covering these xlat tables is 0 and so it is ignored.
Change-Id: I4cf0a4cc090298811cca53fc9cee74df0f2b1512
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
In LOAD_IMAGE_V1 (i.e when LOAD_IMAGE_V2=0) the bl2_tzram_layout is,
by default, assigned to the bl1_tzram_layout->free_base which is
dynamically calculated based on the images loaded in memory. There is a
chance that the bl2_tzram_layout will be assigned a value not aligned to
8 bytes. This patch rounds up the free_base value for the required
alignment.
This doesn't happen in LOAD_IMAGE_V2 because the bl2_tzram_layout is
assigned by default to the bl1_tzram_layout->total_base, which is
aligned.
Change-Id: Idc583e7dad993d02ac6791797406118c96f83fa1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Follow convention of shorter names for smaller scope to fix
violations of MISRA rule 5.7
To prevent violation of directive 4.5 having variable name channel
in css_pm_scmi.c not being typographically ambiguous change macro
argument CHANNEL in css_mhu_doorbell.h change argument to _channel
to fit with our convention which is a permitted exception of
directive 4.5 for this project
Rule 5.7: A tag name shall be a unique identifier
Fixed for:
make LOG_LEVEL=50 PLAT=juno
Change-Id: I147cdb13553e83ed7df19149b282706db115d612
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
Use a _ prefix for macro arguments to prevent that argument from
hiding variables of the same name in the outer scope
Rule 5.3: An identifier declared in an inner scope shall not
hide an identifier declared in an outer scope
Fixed For:
make LOG_LEVEL=50 PLAT=juno
Change-Id: I575fbc96e8267f2b075e88def1f6e3185394613a
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
The slave ports of LD20 CCI-500 are connected as follows:
S0: CA53
S1: CA72
Be careful because the slave interface is not arranged in the
cluster number order (CA72: cluster 0, CA53: cluster 1).
Root-caused-by: Tetsuya Yoshizaki <yoshizaki.tetsuya@socionext.com>
Signed-off-by: Satoshi Ikawa <ikawa.satoshi@socionext.com>
The upcoming patch that adds dynamic mitigation for Cortex-A76
requires that DYNAMIC_WORKAROUND_CVE_2018_3639=1. On FVP, we pull in
all the CPU files into the build which means there will be a build
failure if DYNAMIC_WORKAROUND_CVE_2018_3639=0.
Change-Id: I2e781cbeafbf5d16eaabf76a1677e0c9f81269d2
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
Both Cortex-Ares and Cortex-A76 CPUs use the ARM DynamIQ Shared Unit
(DSU). The power-down and power-up sequences are therefore mostly
managed in hardware, and required software operations are simple.
Change-Id: I3a9447b5bdbdbc5ed845b20f6564d086516fa161
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>
This patch bumps up the BL1-RW size for Juno and at the same time reduces
the BL2 size when TBB is enabled, TF_MBEDTLS_KEY_ALG=rsa+ecdsa. The BL2
size for this config is reduced as it was observed that the peak memory
usage is only reached when SPD=opteed and the dual rsa+ecdsa support is
not needed for this case.
Change-Id: Ia9009771b5cfd805e9cc75410aabb7db99fc2fbc
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The patch changes the layout of BL images in memory to enable
more efficient use of available space. Previously BL31 was loaded
with the expectation that BL2 memory would be reclaimed by BL32
loaded in SRAM. But with increasing memory requirements in the
firmware, we can no longer fit BL32 in SRAM anymore which means the
BL2 memory is not reclaimed by any runtime image. Positioning BL2
below BL1-RW and above BL31 means that the BL31 NOBITS can be
overlaid on BL2 and BL1-RW.
This patch also propogates the same memory layout to BL32 for AArch32
mode. The reset addresses for the following configurations are also
changed :
* When RESET_TO_SP_MIN=1 for BL32 in AArch32 mode
* When BL2_AT_EL3=1 for BL2
The restriction on BL31 to be only in DRAM when SPM is enabled
is now removed with this change. The update to the firmware design
guide for the BL memory layout is done in the following patch.
Change-Id: Icca438e257abe3e4f5a8215f945b9c3f9fbf29c9
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The weak pragma was assigned twice to the bl2_plat_handle_post_image_load
definition both in plat/common/ and in plat/arm/common/ this was an error as
it should have only have been defined in plat/common
Change-Id: Id85e14c699cb09ed998d1677f2a172e760911918
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
BL31 is running out of space, and the use-case of SPM doesn't require it
to be in SRAM. To prevent BL31 from running out of space in the future,
move BL31 to DRAM if SPM is enabled.
Secure Partition Manager design document updated to reflect the changes.
Increased the size of the stack of BL31 for builds with SPM.
The translation tables used by SPM in Arm platforms have been moved back
to the 'xlat_tables' region instead of 'arm_el3_tzc_dram'. Everything is
in DRAM now, so it doesn't make sense to treat them in a different way.
Change-Id: Ia6136c8e108b8da9edd90e9d72763dada5e5e5dc
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.
The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.
Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.
The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.
Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The vcu disable bit in efuse ipdisable register is valid
only if PL powered up so, consider PL powerup status for
determing EG/EV part. If PL is not powered up, display
EG/EV as a part of string. The PL powerup status will
be filled by pmufw based on PL PROGB status in the
9th bit of version field.This patch also used IPI
to get this info from pmufw instead of directly accessing
the registers. Accessing this info from pmufw using
IPI fixes the issue of PMUFW access denied error for
reading IPDISABLE register.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
This patch adds new API for processing secure images. This API
is used for authentication and decryption of secure images using
xilsecure in pmufw.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Existing code blocks each IPI send request in ipi_mb_notify()
function till pmu clears respective bit in ipi observation
register.
After sending PM_SYSTEM_SHUTDOWN request to PMU, PMU will
restart APU. While PMU is restarting APU, ATF is running out
of OCM, which can cause read/write hang from/to OCM.
There is no need to wait for notification from PMU in case
of SystemShutdown request in ATF, as APU is going to restart.
This patch fixes APU only restart issue.
Signed-off-by: Tejas Patel <tejasp@xilinx.com>
Acked-by: Wendy Liang <wendy.liang@xilinx.com>
This patch makes bitstream load blocking call and waits until
bitstream is loaded successfully or return with error.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Avesh Khan <aveshk@xilinx.com>
GET_CALLBACK_DATA function is not required now. IPI mailbox
can be used instead of GET_CALLBACK_DATA function.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
PMU IPI-1 is used for callbacks from PMU to master. Unsecure
master can also receive callbacks from PMU, so make PMU IPI-1
as non-secure.
All requests from master(s) to PMU would still go on PMU IPI-1
secure channel.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Remove includes of gic_common.h and string.h which
are not required.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Acked-by: Jolly Shah <jollys@xilinx.com>
Xilinx now requires the PMU FW when using ATF, so it doesn't make sense
to maintain checks for the PMU FW in ATF. This also means that cases
where ATF came up before the PMU FW (such as on QEMU) ATF will now hang
waiting for the PMU FW instead of aborting.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Use positive logic (pm_up instead of pm_down) to check whether PMU
services are available. This change also puts the variable into the
BSS section rather than the Data section as the variable is now
initialized to 0 rather than 1.
Signed-off-by: Will Wong <WILLW@xilinx.com>
Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
If we can't find the FSBL handoff struct don't panic and just use the
defaults instead.
We still print a warning to the user to let them know what we couldn't
find it.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Instead of calling panic() in fsbl_atf_handover() return the error
status so that bl31_early_platform_setup() can act accordingly.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Type "entry_point_info_t" is used in zynqmp_private.h. It is defined
in "bl_common.h". The header file which defines the type should be
included.
Signed-off-by: Wendy Liang <jliang@xilinx.com>
Added SHA to calculate SHA3 hash,RSA to encrypt data with
public key and decrypt with private key and AES to do symmetric
encryption with User key or device key.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Read ipdisable reg which needs to be used for cg/eg/ev device detection.
ATF runs in EL3 that's why this read can be done directly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
This patch corrects the SVD mask for getting chip ID
using 0xe is wrong and 0x7 is correct.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
psci system_reset and system_off calls now retrieve shutdown scope on
the fly. The default scope is system, but it can be changed by calling
pm_system_shutdown(2, scope)
Until full support for different restart scopes becomes available with
PSCI 1.1 this change allows users to set the reboot scope to match
their application needs.
Possible scope values:
0 - APU subsystem: does not affect RPU, PMU or PL
1 - PS only: shutdown/restart entire PS without affecting PL
2 - System: shutdown/restart applies to entire system
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Davorin Mista <davorin.mista@aggios.com>
The PM_INIT_FINALIZE PM API is required to inform the PFW that APU is
done with requesting nodes and that not-requested nodes can be powered
down. If PM is not enabled, this call will never be made and PFW will
never power down any of the nodes which APU can use.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
This patch adds pm_secure_rsaaes() API to provide access to
the xilsecure library for loading secure images
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Read boot mode register using pm_mmio_read if pmu is
present otherwise access it directly using mmio_read_32().
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The pm_req_wakeup PM API accepts start address (64-bit unsiged integer)
and a flag stating if address should be used. To save an argument
of the SMC call, flag is encoded in the LSB of the address, since
addresses are word aligned.
Decode start address and use-address flag in the PM SMC handler and
pass them to pm_req_wakeup.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
Call to pm_client_wakeup from pm_req_wakeup prevented the PM API
call to be used to wake up non-APU processor (e.g. from higher ELs),
since it clears power down request for specified APU processor.
Move this function out of pm_client_wakeup to allow passing wake up
requests to the PMU for other processor in the system.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
NODE_EXTERN is the slave node which represents an external wake
source.
Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
Beside standard suspend-to-RAM state, Zynq MPSoC supports
suspend-to-RAM state with additional power savings, called
power-off suspend-to-RAM. If this mode is set, only NODE_EXTERN
must be set as wake source. Standard suspend-to-RAM procedure
is unchanged.
This patch adds support for setting suspend mode from higher
ELs and ensuring that all conditions for power-off suspend mode
are set.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
pm_get_node_status API function returns 3 values:
-status: Current power state of the node
-requirements: Current requirements for the node
-usage: Current usage of the node
The last two values only apply to slave nodes.
Signed-off-by: Anes Hadziahmetagic <anes.hadziahmetagic@aggios.com>
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
The MT bit in MPIDR is always set for SGI platforms and so the
core position calculation code is updated to take into account
the thread affinity value as well.
Change-Id: I7b2a52707f607dc3859c6bbcd2b145b7987cb4ed
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Signed-off-by: Vishwanatha HG <vishwanatha.hg@arm.com>
Instead of instantiating a local copy of GICv3 driver data for SGI
platforms, reuse the existing instance of GICv3 driver data available
in the arm common platform code.
Change-Id: If6f38e15d1f0e20cea96fff98091da300015d295
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Signed-off-by: Vishwanatha HG <vishwanatha.hg@arm.com>
This reverts commit 2f18aa1fa3.
It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.
Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
To catch early hangs in resume, this sets up the watchdog before
anything else in the pmusram code (ignoring setting up the stack...).
This uses hard coded settings for the watchdog until the proper
watchdog restore later on in the firmware/kernel.
This also restores the old watchdog register values before the PLLs
are restored to make sure we don't temporarily switch over to a 1/3s
timeout on the watchdog when the pclk_wdt goes from 4MHz to 100MHz.
Change-Id: I8f7652089a88783271b17482117b4609330abe80
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
All the m0 code run in SRAM before, but we need to watch PMU_POWER_ST
when SOC enter into FSM, and SRAM will shutdown during this time, so
this code need run in PMUSRAM. But PMUSRAM only 8K space, we can not
put all the m0 binary into PMUSRAM, Split the M0 binary into two, dram
part still run in SRAM, and suspend part run in PMUSRAM.
Change-Id: Ie08bdf3e2b8838f12b9297fe60ab0aad219684b1
Signed-off-by: Lin Huang <hl@rock-chips.com>
we need to enable PMU_WKUP_RST_EN for pmu powermode configure, since
enable wakeup reset will hold the soc status, so the SOC will not affect
by some power or other single glitch when resume, and keep the soc in the
right status. And it not need to enable DDRIO_RET_HW_DE_REQ, the ddr resume
will do it manual.
Change-Id: Ib4af897ffb3cb63dc2aa9a6002e5d9ef86ee4a49
Signed-off-by: Lin Huang <hl@rock-chips.com>
SGI-575's NSRAM is neither in the same place nor the same size as Juno's.
Change-Id: Id6d692e9c7e9c1360014bb525eda966ebe29c823
Signed-off-by: Chris Kay <chris.kay@arm.com>
Normally, BL33 needs to contain a boot loader like U-Boot or UEFI that
eventually gives control to the OS. However, in some cases, this boot
sequence may be too slow. For example, when doing tests in a
cycle-accurate emulator, the user may only be interested in the
interaction between the Trusted Firmware and the OS, not in the boot
process itself.
The new option ARM_LINUX_KERNEL_AS_BL33 allows BL33 to contain the Linux
kernel image by changing the value of registers x0-x3 to the values
expected by the kernel. This option requires the device tree blob (DTB)
to be present in memory. Its address must be specified in the newly
introduced ARM_PRELOADED_DTB_BASE build option. For now, it only supports
AArch64 kernels.
This option is only available when RESET_TO_BL31=1. For this reason
the BL33 binary must be preloaded in memory and PRELOADED_BL33_BASE must
be used.
For example, if the kernel is loaded at 0x80080000 and the DTB is loaded
at address 0x82000000, the firmware could be built like this:
CROSS_COMPILE=aarch64-linux-gnu- \
make PLAT=fvp DEBUG=1 \
RESET_TO_BL31=1 \
ARM_LINUX_KERNEL_AS_BL33=1 \
PRELOADED_BL33_BASE=0x80080000 \
ARM_PRELOADED_DTB_BASE=0x82000000 \
all fip
Change-Id: If9dc847c65ae2d0c27b51f0fd44fc06b28497db9
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The old API is deprecated and will eventually be removed.
Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.
The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.
Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.
The size of BL31 has been increased in builds with SPM.
Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
- Assign 0x10 for RAS exceptions on ARM platforms, and install
EHF priority descriptor.
- Call the common RAS initialisation from ARM BL31 setup.
- Add empty definitions for platform error records and RAS interrupts.
Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Previous patches added frameworks for handling RAS errors. This patch
introduces features that the platform can use to enumerate and iterate
RAS nodes:
- The REGISTER_RAS_NODES() can be used to expose an array of
ras_node_info_t structures. Each ras_node_info_t describes a RAS
node, along with handlers for probing the node for error, and if
did record an error, another handler to handle it.
- The macro for_each_ras_node() can be used to iterate over the
registered RAS nodes, probe for, and handle any errors.
The common platform EA handler has been amended using error handling
primitives introduced by both this and previous patches.
Change-Id: I2e13f65a88357bc48cd97d608db6c541fad73853
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
At present, any External Abort routed to EL3 is reported as an unhandled
exception and cause a panic. This patch enables ARM Trusted Firmware to
handle External Aborts routed to EL3.
With this patch, when an External Abort is received at EL3, its handling
is delegated to plat_ea_handler() function. Platforms can provide their
own implementation of this function. This patch adds a weak definition
of the said function that prints out a message and just panics.
In order to support handling External Aborts at EL3, the build option
HANDLE_EA_EL3_FIRST must be set to 1.
Before this patch, HANDLE_EA_EL3_FIRST wasn't passed down to
compilation; this patch fixes that too.
Change-Id: I4d07b7e65eb191ff72d63b909ae9512478cd01a1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Previously mem_protect used to be only supported from BL2. This is not
helpful in the case when ARM TF-A BL2 is not used. This patch demonstrates
mem_protect from el3_runtime firmware on ARM Platforms specifically
when RESET_TO_BL31 or RESET_TO_SP_MIN flag is set as BL2 may be absent
in these cases. The Non secure DRAM is dynamically mapped into EL3 mmap
tables temporarily and then the protected regions are then cleared. This
avoids the need to map the non secure DRAM permanently to BL31/sp_min.
The stack size is also increased, because DYNAMIC_XLAT_TABLES require
a bigger stack.
Change-Id: Ia44c594192ed5c5adc596c0cff2c7cc18c001fde
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Since commit 031dbb1224 ("AArch32: Add essential Arch helpers"),
it is difficult to use consistent format strings for printf() family
between aarch32 and aarch64.
For example, uint64_t is defined as 'unsigned long long' for aarch32
and as 'unsigned long' for aarch64. Likewise, uintptr_t is defined
as 'unsigned int' for aarch32, and as 'unsigned long' for aarch64.
A problem typically arises when you use printf() in common code.
One solution could be, to cast the arguments to a type long enough
for both architectures. For example, if 'val' is uint64_t type,
like this:
printf("val = %llx\n", (unsigned long long)val);
Or, somebody may suggest to use a macro provided by <inttypes.h>,
like this:
printf("val = %" PRIx64 "\n", val);
But, both would make the code ugly.
The solution adopted in Linux kernel is to use the same typedefs for
all architectures. The fixed integer types in the kernel-space have
been unified into int-ll64, like follows:
typedef signed char int8_t;
typedef unsigned char uint8_t;
typedef signed short int16_t;
typedef unsigned short uint16_t;
typedef signed int int32_t;
typedef unsigned int uint32_t;
typedef signed long long int64_t;
typedef unsigned long long uint64_t;
[ Linux commit: 0c79a8e29b5fcbcbfd611daf9d500cfad8370fcf ]
This gets along with the codebase shared between 32 bit and 64 bit,
with the data model called ILP32, LP64, respectively.
The width for primitive types is defined as follows:
ILP32 LP64
int 32 32
long 32 64
long long 64 64
pointer 32 64
'long long' is 64 bit for both, so it is used for defining uint64_t.
'long' has the same width as pointer, so for uintptr_t.
We still need an ifdef conditional for (s)size_t.
All 64 bit architectures use "unsigned long" size_t, and most 32 bit
architectures use "unsigned int" size_t. H8/300, S/390 are known as
exceptions; they use "unsigned long" size_t despite their architecture
is 32 bit.
One idea for simplification might be to define size_t as 'unsigned long'
across architectures, then forbid the use of "%z" string format.
However, this would cause a distortion between size_t and sizeof()
operator. We have unknowledge about the native type of sizeof(), so
we need a guess of it anyway. I want the following formula to always
return 1:
__builtin_types_compatible_p(size_t, typeof(sizeof(int)))
Fortunately, ARM is probably a majority case. As far as I know, all
32 bit ARM compilers use "unsigned int" size_t.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 4c0d039076 ("Rework type usage in Trusted Firmware") changed
the type usage in struct declarations, but did not touch the definition
side. Fix the type mismatch.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
SGI-575 platform is based on Cortex-A75 processor which has its MT bit
in the MPIDR register set to '1'. So the Arm platform layer code has
to be made aware of this.
Signed-off-by: Sudipto Paul <sudipto.paul@arm.com>
Currently the SCMI driver supports MHUv1, but Arm platforms may have
varied versions of MHU driver, with MHUv2 controllers being in the
latest Arm platforms.
This patch updates the SCMI driver to support MHUv2, specifically that
the sender must send the wake-up to the receiver before initiating any
data transfer.
Also, the existing mhu driver files, css_mhu.c and css_mhu.h, have been
moved from the scpi directory to a new directory, css/drivers/mhu.
Change-Id: I9b46b492a3e1d9e26db12d83a9773958a8c8402f
Signed-off-by: Samarth Parikh <samarth.parikh@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp SPD=tspd TRUSTED_BOARD_BOOT=1 \
GENERATE_COT=1 ARM_ROTPK_LOCATION=devel_rsa \
ROT_KEY=arm_rotprivk_rsa.pem MBEDTLS_DIR=mbedtls all
Change-Id: Ie4cd6011b3e4fdcdd94ccb97a7e941f3b5b7aeb8
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp SPD=tspd all
Change-Id: I0a16cf68fef29cf00ec0a52e47786f61d02ca4ae
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.3: All declarations of an object or function shall
use the same names and type qualifiers.
Fixed for:
make DEBUG=1 PLAT=juno LOG_LEVEL=50 all
Change-Id: I0e4a03a0d2170cb1c632e079112a972091994a39
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I32b223251b8bf5924149d89431a65d3405a73d3e
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Fix that DDR can't work at 533MHz. Now step to set DDR frequency
from 150MHz to 800MHz. DDR could work among these frequency, 150MHz,
266MHz, 400MHz, 533MHz and 800MHz.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Add TZMP1 support on Juno and increase the BL2 size accordingly due to the
extra data structures to describe the TZC regions and the additional code.
Signed-off-by: Summer Qin <summer.qin@arm.com>
This patch allows the ARM Platforms to specify the TZC regions to be
specified to the ARM TZC helpers in arm_tzc400.c and arm_tzc_dmc500.c.
If the regions are not specified then the default TZC region will be
configured by these helpers.
This override mechanism allows specifying special regions for TZMP1
usecase.
Signed-off-by: Summer Qin <summer.qin@arm.com>
This patch introduce TF-A support for NXP's ls1043a platform.
more details information of ls1043a chip and ls1043ardb board
can be found at docs/plat/ls1043a.rst.
Boot sequence on ls1043a is: bootrom loads bl1 firstly, then bl1
loads bl2, bl2 will load bl31, bl32 and bl33, bl31 will boot
bl32(tee os) and bl33(u-boot or uefi), bl33 boot Linux kernel.
Now TF-A on ls1043ardb platform has the following features in this patch:
* Support boot from Nor flash.
* TF-A can boot bl33 which runs in el2 of non-secure world.
* TF-A boot OPTee OS.
* Support PSCI
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Chenyin.Ha <Chenyin.Ha@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: jiaheng.fan <jiaheng.fan@nxp.com>
Signed-off-by: Wen He <wen.he_1@nxp.com>
Building TBBR(SPD=opteed) and non-TBBR TF-A images is breaking for
Juno for different configurations listed below:
* Overflow error of 4096 bytes for rsa algorithm.
* Overflow error of 8192 bytes for ecdsa algorithm.
* Overflow error of 4096 bytes for rsa+ecdsa algorithm.
* Overflow error of 4096 bytes for non-TBBR case.
So this patch increments macro PLAT_ARM_MAX_BL2_SIZE for all the above
cases accordingly.
Change-Id: I75ec6c0a718181d34553fe55437f0496f467683f
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
This fixes an off by 576x bug the the sram_udelay code. The wrong
value was multipled by the system ticks per mhz value (which is 24),
so we delayed for 1/576th of the requested time.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
The current AArch32 version of plat_arm_calc_core_pos uses an incorrect
algorithm to calculate the linear position of a core / PE from its
MPIDR.
This patch corrects the algorithm to:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId
which supports cores where there are more than 1 PE per CPU.
NOTE: the AArch64 version was fixed in 39b21d1
Change-Id: I72aea89d8f72f8b1fef54e2177a0fa6fef0f5513
Signed-off-by: David Cunado <david.cunado@arm.com>
Use the console_pl011_core_* functions directly in the crash console
callbacks.
This bypasses the MULTI_CONSOLE_API for the crash console (UART1), but
allows using the crash console before the C runtime has been initialized
(eg to call ASM_ASSERT). This retains backwards compatibility with respect
to functionality when the old API is used.
Use the MULTI_CONSOLE_API to register UART0 as the boot and runtime
console.
FixesARM-software/tf-issues#572
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
Add support for System Guidance for Infrastructure platform SGI575.
Change-Id: I0125c2ed4469fbc8367dafcc8adce770b6b3147d
Signed-off-by: Nariman Poushin <nariman.poushin@linaro.org>
If system is still accessing storage device, reboot operation
may cause data broken. So add the flush and delay operation
before system reset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Void pointers have been used to access linker symbols, by declaring an
extern pointer, then taking the address of it. This limits symbols
values to aligned pointer values. To remove this restriction an
IMPORT_SYM macro has been introduced, which declares it as a char
pointer and casts it to the required type.
Change-Id: I89877fc3b13ed311817bb8ba79d4872b89bfd3b0
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>
Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.
The crash console doesn't use this API, it uses internally the core
functions of the 16550 console.
`bl31_plat_runtime_setup` is no longer needed. When this platform port
was introduced, that function used to disable the console. It was needed
to override that behaviour. The new behaviour is to switch to the
runtime console. The console is registered for all scopes (boot, crash
and runtime) in `rpi3_console_init` so it is not needed to override the
default behaviour anymore.
Update documentation.
Change-Id: If2ee8f91044216183b7ef142e5c05ad6220ae92f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Removes fall-through in switch statement on unknown interrupt type in
release builds.
Previous behaviour was to assert(0) on default case in debug builds but
fall through and interpret the unknown interrupt type as
INTR_TYPE_EL3 in release builds.
Change-Id: I05fb0299608efda0f9eda2288d3e56e5625e05c9
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>
Add crash_console_init declaration to console.h
Only enable MULTI_CONSOLE_API for AArch64
FixesARM-software/tf-issues#571
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
Add support for the new MULTI_CONSOLE_API
Crash information is now displayed in both the runtime and crash consoles,
if a crash occurs after the runtime console has been enabled
Enable MULTI_CONSOLE_API by default on qemu builds
FixesARM-software/tf-issues#561
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
When the source code says 'SMCC' it is talking about the SMC Calling
Convention. The correct acronym is SMCCC. This affects a few definitions
and file names.
Some files have been renamed (smcc.h, smcc_helpers.h and smcc_macros.S)
but the old files have been kept for compatibility, they include the
new ones with an ERROR_DEPRECATED guard.
Change-Id: I78f94052a502436fdd97ca32c0fe86bd58173f2f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Allow qemu users to enable stack protection. Since the virt platform
does not provide an RNG, use a basic, timer-based, canary generation,
similarly to FVP.
Increase SRAM size and BL2 size to fit images when stack protection is
enabled.
Notice that stack protection is not enabled by default in qemu.
FixesARM-software/tf-issues#568
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
there are two fix for save/restore watchdog register:
1. watchdog plck will shutdown after secure_watchdog_disable(), so need
to save register before it and restore after secure_watchdog_enable().
2. need write 0x76 to cnt_restart to keep watchdog alive when restore
watchdog register.
Change-Id: I1f6fbceae22186e3b72a87df6332a110adf37479
Signed-off-by: Lin Huang <hl@rock-chips.com>
x3 will be assigned by the folloing instructions.
So the first instruction is not needed any more.
old method:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER)
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId
it should be
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER) * FVP_MAX_PE_PER_CPU
+ (CPUId * FVP_MAX_PE_PER_CPU)
+ ThreadId
which can be simplified as:
(ClusterId * FVP_MAX_CPUS_PER_CLUSTER + CPUId) * FVP_MAX_PE_PER_CPU + ThreadId
Signed-off-by: Wang Feng <feng_feng.wang@spreadtrum.com>
Existing database allows to set only single mode for SDIO.
SDIO can have different groups (8 bit, 4 bit and 1 bit).
As there is only single SDIO group in each pin, it is not
possible to use different mode groups for SDIO.
Extend database in generic way to allow multiuple function
groups in single pin. Add different SDIO groups to pins and
create separate functions for each modes.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Define default DDR location to which ATF has to compiled
if DEBUG option is enabled. This is required now, as the ATF cant fit
in OCM with DEBUG option enabled. The default value is 0x1000 and can be
used till 0x7ffff. User can still override as per wish/requirement
using current commandline options.
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add pin control APIs which driver can use to query
pin information from firmware. Using these APIs,
driver do not need to maintain hard-coded pin database.
Major changes in patch are:
- Add pin database with pins, functions and function groups
information
- Implement APIs for pin information queries
- Update pin control APIs for get/set functions to use new
pin control database. Remove pin database which was added
earlier.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add IOCTLs to read/write global general storage and
persistent global general storage registers access.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
- Add clock entries and information to clock database.
- Implement APIs to provide clock topology and other
information to caller.
- Implement APIs to control clocks and PLLs.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
These are empty functions with no logic right now. Code
will be added in subsequent commits.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement ioctl APIs which uses MMIO operations
to configure devices. Below IOCTLs are supported
in this patch:
* Set tap delay bypass
* Set SGMII mode
* SD reset
* Set SD/MMC tap delay
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement ioctl APIs which uses MMIO operations
to control RPU operations. Below IOCTLs are supported
in this patch:
* Get RPU operation mode
* Set RPU operation mode
* Configure RPU boot address (OCM/TCM)
* Configure TCM combined mode
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement pin control APIs which uses MMIO operations
to set/get values of configuration parameters.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Implement pin control APIs which uses MMIO operations
to set/get functions for the given pin.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add wrappers for pin control APIs. Actual implementation of
these APIs would be done in subsequent changes.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Add new function and node IDs supported by PMUFW in
function list and node list respectively.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
The FVP platform port for SP_MIN (BL32) didn't map the flash memory
in BL32 for stroring the mem_protect enable state information leading
to synchronous exception. The patch fixes it by adding the region to
the BL32 mmap tables.
Change-Id: I37eec83c3e1ea43d1b5504d3683eebc32a57eadf
Signed-off-by: Joel Hutton <Joel.Hutton@Arm.com>
Boot memory layout is specific for a platform, but should not be
mixed up with other platform specific attributes. A separate file is
much cleaner and better to compare with other platforms. Take a look
at plat/poplar where it is done the same way.
Moved hikey_def.h to system include folder and moved includes from
hikey_def.h to more general platform_def.h.
Signed-off-by: Michael Brandl <git@fineon.pw>
Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.
In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.
Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.
Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This issue was detected when testing FWU on Juno. The Timer
`timer_ops` was not being initialized before being used by
the SDS driver on Juno. This patch adds the call to
`generic_delay_timer_init()` during bl2u_early_platform_setup().
This is done generically for all ARM platforms because the
cost involved is minimal.
Change-Id: I349cf0bd1db68406eb2298b65f9c729f792cabdc
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
plat/hisilicon/hikey/hikey_bl1_setup.c:565:47:
error: value size does not match register size specified by the
constraint and modifier [-Werror,-Wasm-operand-widths]
__asm__ volatile ("mrs %0, cpacr_el1" : "=r"(data));
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
It's unnecessary to call platform driver initialization in image
load driver. We could make bl2_platform_setup() to executing
just before SCP_BL2 by setting flag IMAGE_ATTRIB_PLAT_SETUP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since non-TF ROM is used in HiKey960 platform (Hisilicon Hi3660 SoC),
replace BL1 by BL2_EL3 in normal boot mode.
When flush images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since LOAD_IMAGE_V2 is always enabled in HiKey960 platform. Drop
LOAD_IMAGE v1 to simplify code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
MAP_TSP_MEM could be either in SRAM or DRAM. When MAP_TSP_MEM is in
DRAM, it's overlapped with MAP_DDR.
Since TSP_MEM is always configured in DRAM case, it means
MAP_OPTEE_PAGEABLE is always disabled. Just remove it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The main difference between HiKey960 v1 hardware and HiKey960 v2
hardware is on UART console.
But the function of detecting boardid dumps message before console
ready. So fix it by removing those messages.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since non-TF ROM is used in HiKey platform (Hisilicon Hi6220 SoC),
replace BL1 by BL2_EL3 in normal boot mode.
When we recovery images in recovery mode, keep to use BL1.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Although SRAM is initialized, DCACHE should be cleaned too.
Because MCU is a parrallel core to access SRAM. We need to make
sure that initialized value is really written to SRAM before
MCU using it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Since LOAD_IMAGE_V2 is always enabled in HiKey platform. Drop
LOAD_IMAGE v1 to simplify code.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The register address range of UART1 (crash console) are outside the
address ranges mapped for MMIO, resulting to an MMU abort when the
device registers are accessed.
Increase the size of DEVICE1 memory to include the range of UART1.
FixesARM-software/tf-issues#560
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
This patch removes default platform implementations of sp_min
platform APIs from plat/common/aarch32/plat_common.c. The APIs
are now implemented in `plat_sp_min_common.c` file within the
same folder.
The ARM platform layer had a weak definition of sp_min_platform_setup2()
which conflicted with the weak definition in the common file. Hence this
patch fixes that by introducing a `plat_arm_` version of the API thus
allowing individual boards within ARM platforms to override it if they
wish to.
FixesARM-software/tf-issues#559
Change-Id: I11a74ecae8191878ccc7ea03f12bdd5ae88faba5
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This was correct according to the model specifications , but it seems
that FVP doesn't implement it. It is safer to use the size exposed by
the DTB which is currently used by Linux.
Change-Id: I9aabe3284a50ec2a36ed94966eb7e4ddf37cec3b
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Some generic compatibility functions emit deprecated declaration warnings
even when platforms do not use the deprecated functions directly. This
can be confusing. Suppress these warnings by using:
`#pragma GCC diagnostic ignored "-Wdeprecated-declarations"`
Also emit a runtime warning if the weak plat/common implemntation of
plat_get_syscnt_freq2() is used, as this implies the platform has not
migrated from plat_get_syscnt_freq(). The deprecated declaration warnings
only help detect when platforms are calling deprecated functions, not when
they are defining deprecated functions.
FixesARM-software/tf-issues#550
Change-Id: Id14a92279c2634c1e76db8ef210da8affdbb2a5d
Signed-off-by: Dan Handley <dan.handley@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=juno LOG_LEVEL=50 all
Change-Id: Ic8f611da734f356566e8208053296e6c62b54709
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I7c2ad3f5c015411c202605851240d5347e4cc8c7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.3: All declarations of an object or function shall
use the same names and type qualifiers.
Fixed for:
make DEBUG=1 PLAT=fvp LOG_LEVEL=50 all
Change-Id: I48201c9ef022f6bd42ea8644529afce70f9b3f22
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
Rule 8.4: A compatible declaration shall be visible when
an object or function with external linkage is defined.
Change-Id: I26e042cb251a6f9590afa1340fdac73e42f23979
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>
FVPs that model DynamIQ configuration implements all CPUs in a single
cluster. I.e., such models have a single cluster with more than 4 CPUs.
This differs from existing default build configuration for FVP where up
to 4 CPUs are assumed per cluster.
To allow building for DynamIQ configuration, promote the macro
FVP_MAX_CPUS_PER_CLUSTER as a build option to have it set from the build
command line. The value of the build option defaults to 4.
Change-Id: Idc3853bc95f680869b434b011c2dbd733e40c6ce
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Update qemu_configure_mmu_##_el to add an additional region for code,
marked as MT_CODE | MT_SECURE. Update ro region attributes to NON_EXEC.
Update calls to QEMU_CONFIGURE_BLx_MMU() to pass an additional region for
code. Update calls to pass regions defined in common_def.h.
Increase MAX_MMAP_REGIONS to 10.
Enable SEPARATE_CODE_AND_RODATA by default on QEMU builds.
FixesARM-software/tf-issues#558
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
The SCP binaries provided in the 17.10 Linaro release (and onwards)
have migrated to the SCMI/SDS protocols. Therefore, the ARM TF should
now use the corresponding drivers by default.
This patch changes the default value of the CSS_USE_SCMI_SDS_DRIVER
build option to 1 for Juno.
Change-Id: Idb7e3c6af582f49e332167a2158703c2d781b437
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
MISRA C-2012 Rule 7.3 violation: lowercase l shall not be used as literal suffixes.
This patch resolves this for the ULL() macro by using ULL suffix instead
of the ull suffix.
Change-Id: Ia8183c399e74677e676956e8653e82375d0e0a01
Signed-off-by: David Cunado <david.cunado@arm.com>
This patch restricts building the dynamic config DTBs to the Unix
build environment as the Device Tree compiler may not be available
on other build environments.
Change-Id: Ie690e80010a174300e966240fd977b37561156e0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch also fixes the assumption that the counters are disabled on
the resume path. This is incorrect as the AMU counters are enabled
early in the CPU reset function before `cpuamu_context_restore()`
runs.
Change-Id: I38a94eb166a523f00de18e86860434ffccff2131
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
This patch also fixes `cpuamu_write_cpuamcntenclr_el0()` to use an MSR
instruction instead of an MRS instruction.
Change-Id: Ia6531f64b5ebc60ba432124eaa8d8eaccba40ed0
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>
When the MMU is enabled and the translation tables are mapped, data
read/writes to the translation tables are made using the attributes
specified in the translation tables themselves. However, the MMU
performs table walks with the attributes specified in TCR_ELx. They are
completely independent, so special care has to be taken to make sure
that they are the same.
This has to be done manually because it is not practical to have a test
in the code. Such a test would need to know the virtual memory region
that contains the translation tables and check that for all of the
tables the attributes match the ones in TCR_ELx. As the tables may not
even be mapped at all, this isn't a test that can be made generic.
The flags used by enable_mmu_xxx() have been moved to the same header
where the functions are.
Also, some comments in the linker scripts related to the translation
tables have been fixed.
Change-Id: I1754768bffdae75f53561b1c4a5baf043b45a304
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This patch adds TB_FW_CONFIG for FVP and allows FVP
to select the appropriate HW_CONFIG to include in the
fip. The HW_CONFIG for FVP is selected via `FVP_HW_CONFIG_DTS`
build option. The TB_FW_CONFIG specifies the load address of
HW_CONFIG to BL2. Since currently the load address is different
between AARCH32 and AARCH64, 2 separate TB_FW_CONFIGs are
maintained for the 2 modes.
Change-Id: Ide8581e752dfa900087f5895c775073c841c0daf
Signed-Off-By: Soby Mathew <soby.mathew@arm.com>
The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :
1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.
2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.
3. The `libfdt` sources are now included when BL2 is built
4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.
5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.
6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.
Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.
Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
The `bl1_init_bl2_mem_layout()` API is now deprecated. The default weak
implementation of `bl1_plat_handle_post_image_load()` calculates the
BL2 memory layout and populates the same in x1(r1). This ensures
compatibility for the deprecated API.
Change-Id: Id44bdc1f572dc42ee6ceef4036b3a46803689315
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.
Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch introduces a new BL handover interface. It essentially allows
passing 4 arguments between the different BL stages. Effort has been made
so as to be compatible with the previous handover interface. The previous
blx_early_platform_setup() platform API is now deprecated and the new
blx_early_platform_setup2() variant is introduced. The weak compatiblity
implementation for the new API is done in the `plat_bl_common.c` file.
Some of the new arguments in the new API will be reserved for generic
code use when dynamic configuration support is implemented. Otherwise
the other registers are available for platform use.
Change-Id: Ifddfe2ea8e32497fe1beb565cac155ad9d50d404
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
This patch adds an argument to bl1_plat_post/pre_image_load() APIs
to make it more future proof. The default implementation of
these are moved to `plat_bl1_common.c` file.
These APIs are now invoked appropriately in the FWU code path prior
to or post image loading by BL1 and are not restricted
to LOAD_IMAGE_V2.
The patch also reorganizes some common platform files. The previous
`plat_bl2_el3_common.c` and `platform_helpers_default.c` files are
merged into a new `plat_bl_common.c` file.
NOTE: The addition of an argument to the above mentioned platform APIs
is not expected to have a great impact because these APIs were only
recently added and are unlikely to be used.
Change-Id: I0519caaee0f774dd33638ff63a2e597ea178c453
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
After executing a TLBI a DSB is needed to ensure completion of the
TLBI.
rk3328: The MMU is allowed to load TLB entries for as long as it is
enabled. Because of this, the correct place to execute a TLBI is right
after disabling the MMU.
Change-Id: I8280f248d10b49a8c354a4ccbdc8f8345ac4c170
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Commit fdb1964c34 ("xlat: Introduce
MAP_REGION2() macro") added a granularity field to mmap_region_t.
Tegra platforms were using the v2 xlat_tables implementation in
common/tegra_common.mk, but v1 xlat_tables.h headers in soc/*/plat_setup.c
where arrays are being defined. This caused the next physical address to
be read as granularity, causing EINVAL error and triggering an assert.
Consistently use xlat_tables_v2.h header to avoid this.
FixesARM-software/tf-issues#548.
Signed-off-by: Andreas Färber <afaerber@suse.de>
The console core flush API expects the base address in the first
register, but ARM helpers currently sets the second register with the
base address. This causes an assert failure.
This patch fixes that.
Change-Id: Ic54c423cd60f2756902ab3cfc77b3de2ac45481e
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>
Function plat_ic_get_pending_interrupt_type() should return interrupt
type, not id. The function is used in aarch64 exception handling and
currently the irq/fiq forwarding fails if a secure interrupt happens while
running normal world.
The qemu-specific gic file does not contain any extra functionality so it
can be removed and common file can be used instead.
fixesarm-software/tf-issues#546
Signed-off-by: Santeri Salko <santeri.salko@gmail.com>
Define Qemu AArch32 implementation for some platform functions
(core position, secondary boot cores, crash console). These are
derived from the AArch64 implementation.
BL31 on Qemu is needed only for ARMv8 and later. On ARMv7, BL32 is
the first executable image after BL2.
Support SP_MIN and OP-TEE as BL32: create a sp_min make script target
in Qemu, define mapping for IMAGE_BL32
Minor fix Qemu return value type for plat_get_ns_image_entrypoint().
Qemu model for the Cortex-A15 does not support the virtualization
extension although the core expects it. To overcome the issue, Qemu
ARMv7 configuration set ARCH_SUPPORTS_VIRTUALIZATION to 0.
Add missing AArch32 assembly macro arm_print_gic_regs from ARM platform
used by the Qemu platform.
Qemu Cortex-A15 model integrates a single cluster with up to 4 cores.
Change-Id: I65b44399071d6f5aa40d5183be11422b9ee9ca15
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Looks like this is requirement in the pre-merge static analysis.
misra_violation: [Required] MISRA C-2012 Rule 7.2 violation:
Unsigned constants must be declared with U or u suffix.
Adding ULL as requested. I used ULL() macros for BL*_{BASE,LIMIT}
because they are referenced from linker scripts.
Requested-by: David Cunado <david.cunado@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the xlat region of the on-chip SRAM is always allocated
for all BL images.
The access to the on-chip SRAM is necessary for loading images from
a USB memory device (i.e. when updating firmware), so unneeded for
the usual boot procedure.
To avoid this waste, allocate the xlat region dynamically only for
BL2, and only when it is necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 247fc04351 ("uniphier: switch to BL2-AT-EL3 and remove BL1
support") accidentally changed the location of BL31 and BL32. The
new memory map overlaps with the audio DSP images, also gives impact
to OP-TEE. They are both out of control of ARM Trusted Firmware, so
not easy to change. This commit restores the image layout that was
originally used prior to the BL2-AT-EL3 migration.
Reported-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Allow to handle GZIP-compressed images by giving FIP_GZIP=1 from the
command line.
- Images are GZIP-compressed, then packed into FIP. If Trusted Board
Boot is enabled, certificates are generated based on the compressed
images.
- GZIP decompressor is linked into BL2 to decompress images at
run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the next commit, I will have more usecases to get struct image_info
from image ID. It is better to make a helper function at a different
layer. I do not need the current uniphier_image_descs_fixup() since
the code is small enough to be squashed into the caller side.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Just like bl2_, add pre/post image load handlers for BL1. No argument
is needed since BL2 is the only image loaded by BL1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are cases where we need to manipulate image information before
the load. For example, for decompressing data, we cannot load the
compressed images to their final destination. Instead, we need to
load them to the temporary buffer for the decompressor.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When we add a new callback, we need to duplicate fallbacks among
plat/common/{aarch32,aarch64}/platform_helpers.S This is tedious.
I created a new C file, then moved 3 functions:
plat_error_handler
bl2_plat_preload_setup
plat_try_next_boot_source
They are called from C, so I do not see a good reason to implement
them in assembly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the next commit, I need the image name in lowercase because
output files are generally named in lowercase.
Unfortunately, TOOL_ADD_IMG takes the first argument in uppercase
since we generally use uppercase Make variables.
make_helpers/build_macros.mk provides 'uppercase' macro to convert
a string into uppercase, but 'lowercase' does not exist. We can
implement it if we like, but it would be more straightforward to
change the argument of TOOL_ADD_IMG.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now FIP_ADD_IMG takes care of both fiptool and cert_create
symmetrically. Rename it so that it matches the behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The build system supports generating two FIP images, fip and fwu_fip.
Accordingly, we have similar build macros.
FIP_ADD_PAYLOAD <--> FWU_FIP_ADD_PAYLOAD
CERT_ADD_CMD_OPT <--> FWU_CERT_ADD_CMD_OPT
FIP_ADD_IMG <--> FWU_FIP_ADD_IMG
The duplicated code increases the maintenance burden. Also, the build
rule of BL2U looks clumsy - we want to call MAKE_BL to compile it from
source files, but we want to put it in fwu_fip. We can not do it in a
single macro call since the current MAKE_BL does not support fwu_fip.
To refactor those in a clean way is to support one more argument to
specify the FIP prefix. If it is empty, the images are targeted to
fip, whereas if the argument is "FWU_", targeted to fwu_fip.
The build macros prefixed with FWU_ go away.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Coverity scan done for the coreboot project found the issue:
Coverity (*** CID 1385418: Memory - illegal accesses (OVERRUN))
Coverity (*** CID 1385419: Memory - corruptions (OVERRUN))
Fix the Converity error issue with store_cru[] loop needs to be one
element bigger.
Fixes: ARM-software/tf-issues#544
Change-Id: I420f0a660b24baaa5fc5e78fca242cf750c9bbc7
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
MAP_TSP_MEM could be either in SRAM or DRAM. When MAP_TSP_MEM is in
DRAM, it's overlapped with MAP_DDR.
Since MAP_OPTEE_PAGEABLE isn't used in SRAM case, just remove it.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>