Add dedicated device tree files for STM32MP13.
Add new DDR compatible for STM32MP13x.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Change-Id: Ib1bb9ad8cb2ab9f5f81549635d6604093aeb99d3
Add new APIs to enter and exit "boot mode".
In this mode a potential tamper won't block access or reset
the secure IPs needed while boot, without this mode a dead
lock may occurs.
Change-Id: Iad60d4a0420ec125b842a285f73a20eb54cd1828
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@st.com>
On STM32MP13, the high speed mode for pads in low voltage is different
from STM32MP15. Each peripheral supporting the feature has its own
register.
Special care is taken for SDMMC peripherals. The HSLV mode is enabled
only if the max voltage for the pads is lower or equal to 1.8V.
Change-Id: Id94d2cca17dd4aca4d764230a643b2bb9a5f3342
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Add DT_SDMMC2_COMPAT define in stm32mp1_def.h file in platform.
It allows the use of the compatible in platform code.
Change-Id: I535ad67dd133bab59cf81881adaef42d8e88632c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
On STM32MP13, two new SD1 and SD2 IO compensations cells are added,
for SDMMC1 and SDMMC2. They have to be managed the same way as the
main compensation cell.
Change-Id: Ib7aa648d65fc98e1613bfb46b0e7dd568fd21002
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The nominal voltage for VDDCPU when Cortex-A7 runs at 650MHz is 1.25V
on STM32MP13. VDDCORE should be set at 1.25V as well.
This is necessary, as the PMIC values in its NVMEM are 1.2V.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I3c24fe4cd68c7bf143cf9318ab38a15d6d41b5d2
This field is now declared on the 10 LSB bits on STM32MP13.
Several possible values are specified in the Reference Manual, and
indicate an open or closed device. Other values lead to a system panic.
Change-Id: I697124a21db66a56e7e223d601aa7cf44bb183c4
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Update USB and DFU descriptor used for STM32MP13x
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Change-Id: I6e8111d279f49400a72baa12ff39f140d97e1c70
Add new clock driver for STM32MP13. Split the include file to manage
either STM32MP13 or STM32MP15.
Change-Id: Ia568cd12b1d5538809204f0fd2224d51e5d1e985
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
The IDC register from DBGMCU is duplicated in SYSCFG. As SYSCFG is
always accessible, get chip ID and revision ID from there on STM32MP13.
Change-Id: Ib0b6e8f68a2934a45ec0012f69db6c12a60adb17
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The ERXCTLR_EL1 register reads are RES0 for some error records
leading to a false assert on a read back.
This patch removes the assert on reading back the ERXCTLR_EL1
register to fix this issue.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I0cab30b12656a800ba87b8bb94b4c67a2331dee6
On STM32MP13, there is only 1 DDR port, hence only 1 TZC400 filter.
Change-Id: I4f6750022cdaf658cd209a4bf48a6cdb0717020e
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Increase the fixed regulator number that needs to be
2 for STM32MP13.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Change-Id: Ica990fe9a6494b76aed763d2d353f5234fed7cea
The header must now include by default at least an extra padding
header, increasing the size of the header to 512 bytes (0x200).
This header will be placed at the end of SRAM3 by BootROM, letting
the whole SYSRAM to TF-A.
The boot context is now placed in SRAM2, hence this memory has to be
mapped in BL2 MMU. This mapping is done for all SRAMs in a 2MB area.
Change-Id: I50fcd43ecd0ba2076292b057566efe6809b9971a
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Add the new field for the new header v2.0.
Force MP13 platform to use v2.0.
Removing unused fields in boot_api_context_t for STM32MP13.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Iac81aad9a939c1f305184e335e0a907ac69071df
Add the IP addresses that are STM32MP13 and update the ones for
which the base address has changed.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: Iea71a491da36f721bfd3fbfb010177e2a6a57281
Add the new part numbers and adapt the functions that use them.
There is no package number in OTP as they all share the same GPIO
banks.
This part is then stubbed for STM32MP13.
Change-Id: I13414326b140119aece662bf8d82b387dece0dcc
Signed-off-by: Yann Gautier <yann.gautier@st.com>
On STM32MP13, the chip revision Z is 0x1001, contrary to STM32MP15,
for which it was 0x2001.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: If65482e824b169282abb5e26ca91e16ef7640b52
The backup register used on STM32MP15 to save the boot interface for
the next boot stage was 20. It is now saved in backup register 30
on STM32MP13.
Change-Id: Ibd051ff2eca7202184fa428ed57ecd4ae7388bd8
Signed-off-by: Yann Gautier <yann.gautier@st.com>
STM32MP13 is a single Cortex-A7 CPU, always return true in
stm32mp_is_single_core() function.
Change-Id: Icf36eaa887bdf314137eda07c5751cea8c950143
Signed-off-by: Yann Gautier <yann.gautier@st.com>
* GPIO: On STM32MP13, there are no banks GPIOJ, GPIOK and GPIOZ.
* STM32MP13 is a single Cortex-A7 CPU: remove reset from MPU1
and reset from MCU traces
* There is no MCU on STM32MP13. Put MCU security management
under STM32MP15 flag.
* The authentication feature is not supported yet on STM32MP13,
put the code under SPM32MP15 flag.
* On STM32MP13, the monotonic counter is managed in ROM code, keep
the monotonic counter update just for STM32MP15.
* SYSCFG: put registers not present on STM32MP13 under STM32MP15
flag, as the code that manages them.
* PMIC: use ldo3 during DDR configuration only for STM32MP15
* Reset UART pins on USB boot is no more required.
Change-Id: Iceba59484a9bb02828fe7e99f3ecafe69c837bc7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
SYSRAM is only 128KB and starts at 0x2FFE0000.
SRAMs are added.
BL2 code and DTB sizes are also reduced to fit in 128KB.
Change-Id: I25da99ef5c08f8008ff00d38248d61b6045adad4
Signed-off-by: Yann Gautier <yann.gautier@st.com>
STM32MP13 is a variant of STM32MP1, with a single Cortex-A7, and no
Cortex-M4.
There is only one DDR port.
SP_min is not supported, only OP-TEE can be used as monitor.
STM32MP13 uses the header v2.0 format for stm32image generation
for BL2.
Change-Id: Ie5b0e3230c5e064fe96f3561fc5b3208914dea53
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The stm32image tool is updated to manage new header v2.0 for BL2
images.
Add new structure for the header v2.0 management.
Adapt to keep compatibility with v1.0.
Add the header version major and minor in the command line
when executing the tool, as well as binary type (0x10 for BL2).
Change-Id: I70c187e8e7e95b57ab7cfad63df314307a78f1d6
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
This patch applies CVE-2022-23960 workarounds for Cortex-A75,
Cortex-A73, Cortex-A72 & Cortex-A57. This patch also implements
the new SMCCC_ARCH_WORKAROUND_3 and enables necessary discovery
hooks for Coxtex-A72, Cortex-A57, Cortex-A73 and Cortex-A75 to
enable discovery of this SMC via SMC_FEATURES. SMCCC_ARCH_WORKAROUND_3
is implemented for A57/A72 because some revisions are affected by both
CVE-2022-23960 and CVE-2017-5715 and this allows callers to replace
SMCCC_ARCH_WORKAROUND_1 calls with SMCCC_ARCH_WORKAROUND_3. For details
of SMCCC_ARCH_WORKAROUND_3, please refer SMCCCv1.4 specification.
Signed-off-by: Bipin Ravi <bipin.ravi@arm.com>
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Ifa6d9c7baa6764924638efe3c70468f98d60ed7c
Update WA for Errata A-050426 as Commands for
PEX (PEX1..PEX6) , lnx1_e1000#0, lnx1_xfi and
lnx2_xfi has been moved to PBI phase.
This patch requires RCW to include PBI commands
to write commands in BIST mode for PEX, lnx1_e1000,
lnx1_xfi and lnx2_xfi IP blocks.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Change-Id: I27c2b055c82c0b58df83449f9082bfbfdeb65115
In anticipation of Spectre BHB workaround mitigation patches, we
disable the RECLAIM_INIT_CODE for FVP platform. Since the spectre
BHB mitigation workarounds inevitably increase the size of the various
segments due to additional instructions and/or macros, these segments
cannot be fit in the existing memory layout designated for BL31 image.
The issue is specifically seen in complex build configs for FVP
platform. One such config has TBB with Dual CoT and test secure
payload dispatcher(TSPD) enabled. Even a small increase in individual
segment size in order of few bytes might lead to build fails due to
alignment requirements(PAGE_ALIGN to 4KB).
This is needed to workaround the following build failures observed
across multiple build configs:
aarch64-none-elf-ld.bfd: BL31 init has exceeded progbits limit.
aarch64-none-elf-ld.bfd: /work/workspace/workspace/tf-worker_ws_2/trusted_firmware/build/fvp/debug/bl31/bl31.elf section coherent_ram will not fit in region RAM
aarch64-none-elf-ld.bfd: BL31 image has exceeded its limit.
aarch64-none-elf-ld.bfd: region RAM overflowed by 4096 bytes
Change-Id: Idfab539e9a40f4346ee11eea1e618c97e93e19a1
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Pass NS-load address as ~0UL to the 'set_config_info' function while
updating FW_CONFIG device tree information since it is always loaded
into secure memory.
Change-Id: Ieeaf9c97085128d7b7339d34495bdd58cd9fcf8a
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Pass NS-load address as ~0UL to the 'set_config_info' function while
updating FW_CONFIG device tree information since it is always loaded
into secure memory.
Change-Id: I64e8531e0ad5cda63f14d838efb9da9cf20beea8
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Pass NS-load address as ~0UL to the 'set_config_info' function while
updating FW_CONFIG device tree information since it is always loaded
into secure memory.
Change-Id: Ia33adfa9e7b0392f62056053a2df7db321a74e22
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
This allows TF-A's a3700_system_reset() function to try Warm reset
method when CM3 reset method is not implemented by WTMI firmware.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I7303197373e1a8ca5a44ba0b1e90b48855d6c0c3
* changes:
Revert "feat(sgi): deviate from arm css common uart related defi..."
Revert "feat(sgi): route TF-A logs via secure uart"
Revert "feat(sgi): add page table translation entry for secure uart"
Revert submission 14286-uart_segregation
Reason for revert: Need to wait for companion patches in CI and UEFI/Linux to be upstreamed.
Reverted Changes:
I8574b31d5:feat(sgi): add page table translation entry for se...
I8896ae05e:feat(sgi): route TF-A logs via secure uart
I39170848e:feat(sgi): deviate from arm css common uart relate...
Change-Id: I28a370dd8b3a37087da621460eccc1acd7a30287
Revert submission 14286-uart_segregation
Reason for revert: Need to wait for companion patches in CI and UEFI/Linux to be upstreamed.
Reverted Changes:
I8574b31d5:feat(sgi): add page table translation entry for se...
I8896ae05e:feat(sgi): route TF-A logs via secure uart
I39170848e:feat(sgi): deviate from arm css common uart relate...
Change-Id: I7c488aed9fcb70c55686d705431b3fe017b8927d
Revert submission 14286-uart_segregation
Reason for revert: Need to wait for companion patches in CI and UEFI/Linux to be upstreamed.
Reverted Changes:
I8574b31d5:feat(sgi): add page table translation entry for se...
I8896ae05e:feat(sgi): route TF-A logs via secure uart
I39170848e:feat(sgi): deviate from arm css common uart relate...
Change-Id: I9bec02496f826e184c6efa643f869b2eb3b52539
DFD (Design for Debug) is a debugging tool, which scans flip-flops and
dumps to internal RAM on the WDT reset. After system reboots, those
values could be showed for debugging.
BUG=b:222217317
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I659ea1e0789cf135a71a13b752edaa35123e0941
When trying to boot from an SD card with STM32MP_EMMC_BOOT enabled,
booting fails with:
ERROR: Got unexpected value for active boot partition, 0
ASSERT: plat/st/common/bl2_stm32_io_storage.c:285
because SD cards don't provide a boot partition. So only try reading
from such a partition when booting from eMMC.
Fixes: 214c8a8d08 ("feat(plat/st): add STM32MP_EMMC_BOOT option")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Change-Id: I354b737a3ae3ea577e83dfeb7096df22275d852d
* changes:
feat(sgi): add page table translation entry for secure uart
feat(sgi): route TF-A logs via secure uart
feat(sgi): deviate from arm css common uart related definitions
Updated makefile so that build can accept absolute mbedTLS path.
Change-Id: Ife73266a01d7ed938aafc5e370240023237ebf61
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Updating call order for arm_console_boot_init() and arm_bl31_early_platform_setup().
Signed-off-by: Juan Pablo Conde <juanpablo.conde@arm.com>
Change-Id: If932fff2ee4282a0aacf8751fa81e7665b886467
Patch [1] introduces a mechanism to provide the platform
specified mbedTLS config file, but that result in build failure
for Broadcom platform.
This build failure is due to the absence of the mbedTLS configuration
file i.e. brcm_mbedtls_config.h in the TF-A source code repository.
"fatal error: brcm_mbedtls_config.h: No such file or directory"
This problem was resolved by removing the 'brcm_mbedtls_config.h' entry
from the broadcom platform makefile, allowing this platform to use
the default mbedtls_config.h file.
[1]: https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/13726
Signed-off-by: Manish V Badarkhe <manish.badarkhe@arm.com>
Change-Id: I7cc2efc049aefd3ebce1ae513df9b265fe31ded6
Add page table translation entry for secure uart so that logs from
secure partition can be routed via the same.
Signed-off-by: Rohit Mathew <rohit.mathew@arm.com>
Change-Id: I8574b31d5d138d9f94972deb903124f8c5b70ce4
Route the boot, runtime and crash stage logs via secure UART port
instead of the existing use of non-secure UART. This aligns with the
security state the PE is in when logs are put out. In addition to this,
this allows consolidation of the UART related macros across all the
variants of the Neoverse reference design platforms.
Signed-off-by: Rohit Mathew <rohit.mathew@arm.com>
Change-Id: I8896ae05eaedf06dead520659375af0329f31015
The Neoverse reference design platforms will migrate to use different
set of secure and non-secure UART ports. This implies that the board
specific macros defined in the common Arm platform code will no longer
be usable for Neoverse reference design platforms.
In preparation for migrating to a different set of UART ports, add a
Neoverse reference design platform specific copy of the board
definitions. The value of these definitions will be changed in
subsequent patches.
Signed-off-by: Rohit Mathew <rohit.mathew@arm.com>
Change-Id: I39170848ecd81a7c1bbd3689bd905e45f9435f5c
* changes:
build(intel): enable access to on-chip ram in BL31 for N5X
fix(intel): make FPGA memory configurations platform specific
fix(intel): fix ECC Double Bit Error handling
build(intel): define a macro for SIMICS build
build(intel): add N5X as a new Intel platform
build(intel): initial commit for crypto driver
Remove reserved range for platform provider owned SPs if the dual root
CoT is disabled and allow SPs to populate the range up to MAX_SP_IDS.
Signed-off-by: Imre Kis <imre.kis@arm.com>
Change-Id: Ib4ec18f6530d2515ada21d2c0c388d55aa479d26
Following I2d274fa897171807e39b0ce9c8a28824ff424534:
Remove GICD registers S2 mapping from OP-TEE partition when it runs in a
secure partition on top of Hafnium.
The partition is not meant to access the GIC directly but use the
Hafnium provided interfaces.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I1a38101f6ae9911662828734a3c9572642123f32
Fix coding style violations and alignments:
- Remove additional newlines in headers
- Remove additional newlines in code
- Add newline to separate variable from the code
- Use the same indentation in platform.mk
- Align function parameters
- Use tabs for indentation in kernel-doc format
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I0b12804ff63bc19778e8f21041f9accba5b488b9
This adds the ncore ccu access and enable access to the
on-chip ram for N5X device in BL31.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: I713f6e93d33b6e91705547477ca32cfba5c8c13d
Define FPGA_CONFIG_SIZE and FPGA_CONFIG_ADDR in
platform-specific header. This is due to different
allocated sizes between platforms.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: Iac4fbf4d4940cdf31834a9d4332f9292870dee76
SError and Abort are handled in Linux (EL1) instead of
EL3. This patch adds some functionality that complements the
use cases by Linux as follows:
- Provide SMC for ECC DBE notification to EL3
- Determine type of reset needed and service the request in
place of Linux
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: I43d02c77f28004a31770be53599a5a42de412211
SIMICS builds have different UART configurations compared
to hardware build. Hence, this patch defines a macro to
differentiate between both.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: Iadecd5445e06611486ac3c6a214a6d0dc8ccd27b
This commit adds a new Intel platform called N5X.
This preliminary patch only have Bl31 support.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: Ib31f9c4a5a0dabdce81c1d5b0d4776188add7195
This patch adds driver for Intel FPGA's Crypto Services.
These services are provided by Intel platform
Secure Device Manager(SDM) and are made accessible by
processor components (ie ATF).
Below is the list of enabled features:
- Send SDM certificates
- Efuse provision data dump
- Encryption/decryption service
- Hardware IP random number generator
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Signed-off-by: Sieu Mun Tang <sieu.mun.tang@intel.com>
Change-Id: If7604cd1cacf27a38a9a29ec6b85b07385e1ea26
* changes:
fix(zynqmp): query node status to power up APU
feat(zynqmp): pm_api_clock_get_num_clocks cleanup
feat(zynqmp): add feature check support
fix(zynqmp): use common interface for eemi apis
feat(zynqmp): add support to get info of xilfpga
feat(zynqmp): pass ioctl calls to firmware
When the atf-handoff-params are updated we are returning
FSBL_HANDOFF_SUCCESS, but the return condition is wrongly
updated and added a error log which is incorrect.
Fixing the incorrect log message.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I44ebbb861831b86afcb87f09ddb2e23614393c28
Add the possibility to configure console UART baudrate, it can be passed
as a command line parameter with STM32MP_UART_BAUDRATE. The default value
remains 115200.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I000df70c10b2b4dac1449556596f9820c36cf243
If APU is in suspending state and if wakeup request comes then
PMUFW returns error which is not handled at ATF side.
To fix this, get the APU node status before calling wakeup and
return error if found in suspending state.
Here, we can not handle the error code of pm_req_wakeup() from PMUFW
because ATF is already calling pm_client_wakeup() before calling
pm_req_wakeup().
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I18d47384e46e22ae49e804093ad0641b7a6349e2
There is no reason to have even one additional useless line that's why
remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: Icc3c74249dfe64173aa5c88fb0f9ffe7576fc2aa
This API returns version of supported APIs.
Here, there are three cases to check API version by using feature
check implementation.
1. Completely implemented in TF-A: I mean the EEMI APIs which are
completely implemented in the TF-A only. So check those IDs and
return appropriate version for the same. Right now, it is base
version.
2. Completely implemented in firmware: I mean the EEMI APIs which are
completely implemented in the firmware only. Here, TF-A only passes
Linux request to the firmware to get the version of supported API. So
check those IDs and send request to firmware to get the version and
return to Linux if the version is supported or return the error code
if the feature is not supported.
3. Partially implemented (Implemented in TF-A and firmware both):
First check dependent EEMI API version with the expected version in
the TF-A. If the dependent EEMI API is supported in firmware then
return its version and check with the expected version in the TF-A.
If the version matches then check for the actual requested EEMI API
version. If the version is supported then return version of API
implemented in TF-A.
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I73f20d8222c518df1cda7879548b408b130b5b2e
Currently all EEMI API has its own implementation in TF-A which is
redundant. Most EEMI API implementation in TF-A does same work. It
prepares payload received from kernel, sends payload to firmware,
receives response from firmware and send response back to kernel.
So use common interface for EEMI APIs which has similar functionality.
This will optimize TF-A code.
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I07325644a1fae80211f2588d5807c21973f6d48f
Adds support to get the xilfpga library version and feature list info.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: Iff10ad2628a6a90230c18dc3aebf9dde89f53ecd
Firmware supports new IOCTL for different purposes. To avoid
maintaining new IOCTL IDs in ATF, pass IOCTL call to firmware
for IOCTL IDs implemented in firmware.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: Ie14697c8da9581b0f695f4d33f05161ece558385
Update the MAX_XLAT_TABLES as the memory map has been
added for the dtb to accomodate in DDR address.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I46225673f40f123cdab38efefb038604da119b58
Remove the time stamp and system counter configuration, as
this configuration is already done by the first stage bootloader.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I41554dc2e14d97954bff299df9740a5efa30fad9
With gcc-11, the -Wformat-signedness warning complains about enum values
that should be printed as unsigned values. But the current version of
compiler used in CI states that this parameter is signed. Just cast the
value then.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: Ic0655e5ba9c44fe6abcd9958d7a9972f5de3b7ef
* changes:
fix(intel): null pointer handling for resp_len
fix(intel): define macros to handle buffer entries
fix(intel): change SMC return arguments for INTEL_SIP_SMC_MBOX_SEND_CMD
fix(intel): always set doorbell to SDM after sending command
fix(intel): fix bit masking issue in intel_secure_reg_update
fix(intel): fix ddr address range checker
build(changelog): add new scope for Intel platform
Change resource_req to 0 to disable 26MHz clock.
SPM firmware will pull-down SRCLKENA0 after 26MHz off while suspending.
TEST=verify 26MHz clock off using the oscilloscope.
BUG=b:215639203
Signed-off-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Change-Id: I05702d14a015cabccd6d4af0e3f2a534fbe4dd12
* changes:
fix(nxp-crypto): refine code to avoid hang issue for some of toolchain
build(changelog): add new scope for nxp crypto
fix(lx2): drop erratum A-009810
Platforms which support Realm world cannot boot up
properly if measured boot is enabled at build time.
An assertions occurs due to the missing RMM entry
in the event_log_metadata array.
Signed-off-by: Tamas Ban <tamas.ban@arm.com>
Change-Id: I172f10a440797f7c9e1bc79dc72242b40c2521ea
Previous changes from commit #6a659448 updates resp_len from an integer
type to unsigned integer pointer type. This patch adds proper handling
in case resp_len is a null pointer. Resp_len with value 0 are also
changed to NULL to match the type change.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I75b3e3bfbb188d8e7b329ba3b948c23e31dec490
This patch defines a macro to handle Secure Device Manager's (SDM)
pointer to command & response buffer entries and convert them to the
correct physical address.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I4cf9f1d90e0d5ae4e1a2ce84165864b48c2862e7
'INTEL_SIP_SMC_MBOX_SEND_CMD' SMC runtime service will only return
mailbox status and the argument's length back to the caller
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Change-Id: I50d2ae74845794cab7bf0858e742b5a70e0ea868
This patch fixes the mailbox stall issue when sending mailbox command
that is larger than mailbox command FIFO size.
Large mailbox command will be sent to SDM in multiple chunks. HPS will
set doorbell to SDM when command FIFO full (is_doorbell_triggered will
be set to 1) to notify SDM to read the command data from FIFO, so that
HPS can continue to send the next chunk of command data.
However, HPS will not set the doorbell to SDM at the end if the doorbell
have been set earlier due to FIFO full. This will cause SDM mailbox
service stall because it is still waiting for last chunk of command data.
This patch fixes the code to always set the doorbell to SDM at the end
to get rid of stall issue.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change-Id: Idbe62410a00d92a30c7aeaa26d53d79a910cac0a
intel_secure_reg_update function should apply mask to the value before
write into register.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change-Id: I84bbd06e24b8666528b53030e8359743d438eb5b
This patch fix address range checker to make sure that it does not
errors out on NULL address with size 0. Non-secure software will send
this NULL address if the SMC call doesn't need to pass any address buffer.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: I7e492c562a311ba989570c4ed465f845333ec865
This patch fixes the code issue detected by Klocwork scan. Pointer
'bl_mem_params' returned from call to function 'get_bl_mem_params_node'
may be NULL and the NULL pointer may be caused the system crash. Update
the code to assert if unexpected NULL pointer is returned.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Change-Id: I00f3132a6104618cadce26aa303c0b46b5921d5b
Request ownership and direct access to QSPI by default in BL2.
Previously, this is only done on QSPI boot mode.
Signed-off-by: Abdul Halim, Muhammad Hadi Asyrafi <muhammad.hadi.asyrafi.abdul.halim@intel.com>
Change-Id: Ie222bbf9d719f2f70f89d4739c285efe6df4c955
The erratum A-009810 should not be applied to LX2, the impaction is
that it can cause system reboot when linux tried to power down, so remove
it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I5e24229cf8512eff28b315ebcdf18de555c40c74
* changes:
docs(layerscape): add ls1046a soc and board support
feat(ls1046aqds): add board ls1046aqds support
feat(ls1046afrwy): add ls1046afrwy board support
feat(ls1046ardb): add ls1046ardb board support
feat(ls1046a): add new SoC platform ls1046a
fix(nxp-tools): fix tool location path for byte_swape
fix(nxp-qspi): fix include path for QSPI driver
build(changelog): add new scopes for NXP layerscape platforms
* changes:
feat(stm32mp1): enable format-signedness warning
fix(stm32mp1): correct types in messages
fix(st-pmic): correct verbose message
fix(st-sdmmc2): correct cmd_idx type in messages
fix(st-fmc): fix type in message
fix(mtd): correct types in messages
fix(usb): correct type in message
fix(tzc400): correct message with filter
fix(psci): correct parent_node type in messages
fix(libc): correct some messages
fix(fconf): correct image_id type in messages
fix(bl2): correct messages with image_id
Currently only the lowest 2 DRAM region were configured in the
TrustZone Controller, but the platform supports 6 regions spanning the
whole address space.
Configuring all of them to allow tests to access memory also in those
higher memory regions.
FVP memory map:
https://developer.arm.com/documentation/100964/1116/Base-Platform/Base---memory/Base-Platform-memory-map
Note that last row is wrong, describing a non-existing 56bit address,
all region labels should be shifted upward.
Issue has been reported and next release will be correct.
Change-Id: I695fe8e24aff67d75e74635ba32a133342289eb4
Signed-off-by: Federico Recanati <federico.recanati@arm.com>
Add initial support for RD-Edmunds platform. This platform is considered
as a variant of RD-N2 platform with only major change being the CPU
which is Demeter instead of Neoverse-N2.
Signed-off-by: Tony K Nadackal <tony.nadackal@arm.com>
Change-Id: I939d9eac652fa9e76ad002ee5e6107aa79baa013
Add the flag -Wformat-signedness to TF_CFLAGS for STM32MP1.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I6af18778902b0a4dae1c08735d2d070ef3d137ce
Secure enclave decides the boot bank based on the firmware update
state of the system and updates the boot bank information at a given
location in the flash. In this commit, bl2 reads the given flash
location to indentify the bank from which it should load fip from.
Signed-off-by: Satish Kumar <satish.kumar01@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Change-Id: I7f0f4ffc97189c9deb99db44afcd966082ffbf21
A53 AP BootROM is just 16 kB long and is mapped to address range
0xFFFF0000-0xFFFF4000. RVBAR_EL3 register has value 0xFFFF0000.
A53 AP BootROM itself is in the BootROM window which is 1 MB long and
mapped to address range 0xFFF00000-0xFFFFFFFF.
CM3 BootROM is not accessible from A53 core.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I5d4a4c7b1e7550c4738c67a872d341f945d48bbc
More space in the flash is reserved up front for metadata
parser and UEFI variables. That requires change in the flash
base address of where images are present.
Signed-off-by: Satish Kumar <satish.kumar01@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Change-Id: Ieaabe09374d707de18d36505c69b6c9a8c2ec2e9
This change implements platform specific psci reset
for the corstone1000.
Signed-off-by: Emekcan Aras <Emekcan.Aras@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Change-Id: I25f77234506416c3376ff4a028f6ea40ebe68437
ls1046aqds board is full function board to evaluate ls1046a platform.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Id1befe37a25f7c379e76791538348fd03bba78f7
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the LS1046A
architecture processor capable of support more than 32,000 CoreMark
performance. The FRWY-LS1046A board supports the LS1046A processor,
onboard DDR4 memory, multiple Gigabit Ethernet, USB3.0 and M2_Type_E
interfaces for Wi-Fi, FRWY-LS1046A-AC includes the Wi-Fi card.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I9a9680689e6f17bf4cc76fd5d1883eed6ace5149
The LS1046A reference design board (RDB) is a high-performance
computing, evaluation, and development platform that supports
the Layerscape LS1046A architecture processor.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Ib7a01b309e0b0acc7f38e22b138e9e181dff244a
The LS1046A is a cost-effective, power-efficient, and highly
integrated system-on-chip (SoC) design that extends the reach
of the NXP value-performance line of QorIQ communications
processors. Featuring power-efficient 64-bit Arm Cortex A72
cores with ECC-protected L1 and L2 cache memories for high
reliability, running up to 1.8 GHz.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: rocket <rod.dorris@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Change-Id: I208d9bf1702410463c2b2630d31d0cd4eb7e8837
These changes are required to accommodate 3MB for OP-TEE and this
is required for SP's part of optee
Added size macro's for better readability of the code
Moved uboot execution memory from CVM to DDR
Change-Id: I16657c6e336fe7c0fffdee1617d10af8a2c76732
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Signed-off-by: Arpita S.K <Arpita.S.K@arm.com>
diphda platform is now being renamed to corstone1000.
These changes are to replace all the instances and traces
of diphda corstone1000.
Change-Id: I330f3a112d232b99b4721b6bf0236253b068dbba
Signed-off-by: Arpita S.K <Arpita.S.K@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Add helper functions to generate event log for imx8mm
when MEASURED_BOOT=1.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: Ifc947d749055787fbda0b39170aa2eb8865b7802
The PIE compilation is used only for BL32, move the ENABLE_PIE to
sp_min-stm32mp1.mk file. Override PIE flags, as sp_min.mk file is
included after the flags are set in Makefile.
The BL2_IN_XIP_MEM was added for a feature not yet upstreamed.
It is then removed from platform.mk file.
Change-Id: If055e51e0f160f99cd4e4cf68ca718d4d693119c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
tamp_bkpr() returns a register address. So use uintptr_t instead of
uin32_t.
Signed-off-by: Nicolas Toromanoff <nicolas.toromanoff@foss.st.com>
Change-Id: I5eddfa525465313dadfec18d128248a968ba74e2
Add the SZ_* macros from 32 to 2G.
This allows removing some defines in raw NAND driver
and STM32MP1 boot device selection code.
Change-Id: I3c4d4959b0f43e785eeb37a43d03b2906b7fcfbc
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Signed-off-by: Arpita S.K <Arpita.S.K@arm.com>
Actually BL31_LIMIT is set to 0xffffffff but that doesn't work correctly
with bl31.ld since ". = ALIGN(((1) << (12)));" will try to fill aligned up
to 0x100000000 included, but the RAM size is 0xffffffff, so this leads to
this build error:
```
bl31.elf section `coherent_ram' will not fit in region `RAM'
/home/br-user/git/upstream/ci-tests/zynqmp_zcu102/host/bin/aarch64-buildroot-linux-uclibc-ld: region `RAM' overflowed by 1 byte
```
So let's move BR31_LIMIT to 0x100000000 giving 1 byte more room to fill RAM
up to the end.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Change-Id: Ic0edb8ed159e013f60598a9dd4f50adbf656b38d
Add board support for variant 2 of RD-N2 platform which is a four chip
variant with 4 cores on each chip. The "CSS_SGI_PLATFORM_VARIANT" value
is 2 for multi-chip variant. The "CSS_SGI_CHIP_COUNT_MACRO" can be in
the range [1, 4] for multi-chip variant.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I6412106e80e2f17704c796226c2ee9fe808705ba
Add support for the PSCI CPU_ON call to allow booting secondary CPU
cores. On cold boot they need to be booted with a special register
sequence. Also, the "boot remapper" needs to be configured to point to
the BL31_BASE, so the CPUs actually start executing BL31 after reset.
Change-Id: I406c508070ccb046bfdefd51554f12e1db671fd4
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Booting e.g. Linux in the non-secure world does not work with the
msm8916 port yet because essential hardware is not made available to
the non-secure world. Add more platform initialization to:
- Initialize the GICv2 and mark secure interrupts.
Only secure SGIs/PPIs so far. Override the GICD_PIDR2_GICV2
register address in platform_def.h to avoid a failing assert()
because of a (hardware) mistake in Qualcomm's GICv2 implementation.
- Make a timer frame available to the non-secure world.
The "Qualcomm Timer" (QTMR) implements the ARM generic timer
specification, so the standard defines (CNTACR_BASE etc)
can be used.
- Make parts of the "APCS" register region available to the
non-secure world, e.g. for CPU frequency control implemented
in Linux.
- Initialize a platform-specific register to route all SMMU context
bank interrupts to the non-secure interrupt pin, since all control
of the SMMUs is left up to the non-secure world for now.
Change-Id: Icf676437b8e329dead06658e177107dfd0ba4f9d
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Introduce the bare mimimum base of the msm8916 BL31 port. This is
pretty much just a standard platform "skeleton" with CPU/memory
initialization and an UART driver. This allows booting into
e.g. U-Boot with working UART output.
Note that the plat/qti/msm8916 port is completely separate and does not
make use of anything in plat/qti/common at the moment. The main reason
for that is that plat/qti/common is heavily focused around having a
binary "qtiseclib" component, while the MSM8916 port is fully
open-source (and therefore somewhat limited to publicly documented
functionality).
In the future it might be possible to re-use some of the open-source
parts in plat/qti/common (e.g. spmi_arb.c or pm_ps_hold.c) but it's
not strictly required for the basic functionality supported so far.
Change-Id: I7b4375df0f947b3bd1e55b0b52b21edb6e6d175b
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
From the new binding, the RCC become secured based on the new
compatible. This must be done only from the secure OS initialisation.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I7f0a62f22bfcca638ddaefc9563df00f89f01653
Add an early UART console to ease debug before UART is fully configured.
This is done under flag STM32MP_EARLY_CONSOLE in the first STM32MP1
platform function called (bl2_el3_early_platform_setup()). It uses the
parameters defined for crash console: STM32MP_DEBUG_USART* macros.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: Id6be62368723a0499e97bbf56fb52c166fcbdfad
* changes:
feat(stm32mp1): warn when debug enabled on secure chip
fix(stm32mp1): rework switch/case for MISRA
feat(st): disable authentication based on part_number
* changes:
feat(st-gpio): do not apply secure config in BL2
feat(st): get pin_count from the gpio-ranges property
feat(st-gpio): allow to set a gpio in output mode
refactor(st-gpio): code improvements
The Event Log sources are added to the source-list of BL1 and BL2
images in the Event Log Makefile. It doesn't seem correct since
some platforms only compile Event Log sources for BL2.
Hence, moved compilation decision of Event Log sources to the
platform makefile.
Change-Id: I1cb96e24d6bea5e091d08167f3d1470d22b461cc
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
The "ngpios" property is deprecated and may be removed.
Use the "gpio-ranges" property where the last parameter of that
property is the number of available pins within that range.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Change-Id: I28295412c7cb1246fc753cff0d447b6fdcdc4c0f
Add a banner that inform user that debug is enabled
on a secure chip.
Change-Id: Ib618ac1332b40a1af72d0b60750eea4fc36a8014
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Avoid the use of return inside switch/case in stm32mp_is_single_core().
Although this MISRA rulre might not be enforced, we align on what is done
for stm32mp_is_auth_supported().
Change-Id: I00a5ec1b18c55b4254af00c9c5cf5a4dce104175
Signed-off-by: Yann Gautier <yann.gautier@st.com>
STM32MP15xA and STM32MP15xD chip part numbers don't
support the secure boot.
All functions linked to secure boot must not be used
and signed binaries are not allowed on such chip.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: I5b85f322f5eb3b64415e1819bd00fb2c99f20695
The monotonic counter is stored in an OTP fuse.
A check is done in TF-A.
If the TF-A version is incremented, then the counter will be updated
in the corresponding OTP.
Change-Id: I6e7831300ca9efbb35b4c87706f2dcab35affacb
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Use dt_find_otp_name() to retrieve platform OTP information
from device tree, directly or through stm32_get_otp_index() and
stm32_get_otp_value() platform services.
String definitions replace hard-coded values, they are used to call
this new function.
Change-Id: I81213e4a9ad08fddadc2c97b064ae057a4c79561
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Rename driver file to BSEC2.
Split header file in IP and feature parts.
Add functions to access BSEC scratch register.
Several corrections and improvements.
Probe the driver earlier, especially to check debug features.
Change-Id: I1981536398d598d67a19d2d7766dacc18de72ec1
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Used by driver parsing this node to get information.
Change-Id: I50623a497157adf7b9da6fafe8d79f6ff58c0ebc
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
This patch adds the basic CPU library code to support the Poseidon CPU
in TF-A. Poseidon is derived from HunterELP core, an implementation of
v9.2 architecture. Currently, Hunter CPU the predecessor to HunterELP,
is supported in TF-A. Accordingly the Hunter CPU library code has been
as the base and adapted here.
Signed-off-by: Jayanth Dodderi Chidanand <jayanthdodderi.chidanand@arm.com>
Change-Id: I406b4de156a67132e6a5523370115aaac933f18d
This warning can only be removed if the version is newer than v1.6.0.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I472a8e552305b563447e8148074a5c0970b429e3
Remove stm32mp_incr_shrefcnt(), stm32mp_decr_shrefcnt(),
stm32mp_incr_refcnt() and stm32mp_decr_refcnt() that are unused.
The file is then just removed.
Change-Id: I09ee23c02317df5d8f71cbc355d3ed4a67ce2749
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Due to stm32mp_shres_helpers.h removal, the debug.h header is no more
included. It should then be added to stm32mp1_boot_device.c.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I397911ac05fdff464c010cf3b2e04320a781b4aa
Add support for enabling the FWU multi bank boot feature on the
platform.
Currently, this feature is supported on the STM32MP157C-DK2 board,
which boots off a uSD card. Also, support has been enabled when
booting from a FIP image.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Change-Id: Ia69e858461e2daf599d41d66d7ff2ccae0c341c2
With the FWU Multi Bank update feature, the platform can boot from one
of multiple banks(partitions). Pass the value of bank from which the
platform has booted as boot index to the Update Agent. The Update
Agent will match this boot index value against the active_index field
in the metadata, and update the metadata if there is a mismatch.
Fow now, the mechanism to pass the boot index is platform specific. On
the STM32MP1 platform, the boot index value is passed through a
memorey mapped TAMP register on the SoC.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Change-Id: I0aa665ff9c1db95be8ae19ed8de6d866587d6850
Add support for reading the FWU metadata partition. The metadata
partition stores information on the current active bank along with
information on all the FWU updatable images on the platform. This
information is then used to identify the image to be booted.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Change-Id: I66bc5ac718c21a49c504e698b5b1f5c4daed2d08
With the FWU multi bank boot feature enabled, the platform can boot
from one of the multiple banks(partitions) containing the firmware
images. The bank whose firmware components are to be booted is read
from the FWU metadata structure -- the image to be booted is thus
derived by reading the metadata.
Read the metadata and set the image spec of the corresponding image
type to point to the partition from which the image is to be booted.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Change-Id: I3dfdc7e9202859e917ec4e1f7d1855aad42c6b70
Add GUID's for identifying the firmware image type. With the FWU
multi bank boot feature enabled, these GUID values are used to
identify the firmware image to be booted. This is done by matching
GUID values of images in the io policy table with the Image GUID value
that is read from the FWU metadata structure.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Change-Id: Id9751f02f95fc48ef68e4e3f9f0ddbf6d6319d3c
With the FWU multi bank feature enabled, the identification of
firmware image type is done using the image type GUID instead of
binary_type field.
Add GUID values for the FIP image which can be updated through
the FWU firmware update feature. The GUID values are used in
identifying the firmware images.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Change-Id: If7d9356aa8d2bb3fbcbc87100e6972f1a1862921
The metadata structure copy is passed to the platform routine to set
the image source to boot the platform from. This is done by reading
the metadata structure. Pass the metadata as a read-only copy to the
routine -- the routine only needs to consume the metadata values and
should not be able to update the metadata fields.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Change-Id: I399cad99ab89c71483e5a32a1de0e22df304f8b0
* changes:
feat(stm32mp1): add helper to enable high speed mode in low voltage
refactor(stm32mp1): add helpers for IO compensation cells
feat(stm32mp1): use clk_enable/disable functions
feat(stm32mp1): add timeout in IO compensation
Increase the stack size to avoid stack overflow
when the LOG_LEVEL compile option is set high.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I25047322763bff148dba13848a3a40f4c7cf90b7
Fixed an issue where the CPU and Cluster could not be turned OFF
when the SYSTEM_OFF has executed.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: Id476f815b58246ae0574c04ccb3eb201d09039b9
The LS1043A reference design board (RDB) is a computing, evaluation,
and development platform that supports the Layerscape LS1043A
architecture processor.
The old implementation in tf-a (plat/layerscape/board/ls1043/) is removed,
and this patch is adding it back, it is using the unified software
component and architecture with all the other Layerscape platforms.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Change-Id: I83eee2f9254267b148960b05e25b6c9ba86cf07e
The LS1043A processor was NXP's first quad-core, 64-bit Arm based
processor for embedded networking.
The old implementation in tf-a (plat/layerscape/board/ls1043/) is removed,
and this patch is adding it back, it is using the unified software
component and architecture with all the other Layerscape platforms.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: rocket <rod.dorris@nxp.com>
Change-Id: Ia3877530fae6479bd4a33bbe46b0c0d28ab43160
Remove old implementation for Layerscape ls1043a platform, and
will added it back with unified software architecture of all
Layerscape platforms.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: If038c19ab04d70050ec8e6ab2097b1c4f8324e87
Increate SoC name length as it is not enough for some
SoC personalities.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I2142b4b5162dd3c9ab3afefcdc859063836d8bcc
Use STM32MP_HEADER_RESERVED_SIZE macro instead of a fixed value 0x3000
in linker script.
Change-Id: I2702285c15aebaa1304a891c8aaabc949a912ba6
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This new function is used to fill the register(s) responsible to enable
high speed mode for pad in low voltage (<2.7V).
Change-Id: Ib8abc6628bdf51bbe6a866bc6a9bcdeb4a84a8f4
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Add enable_io_comp_cell and disable_io_comp_cell local helpers
to enable or disable an IO compensation cell.
Change-Id: I65295298a7ece572ae939e2db93d10b188de0f9e
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Use the clock framework functions in SYSCFG driver instead of dedicated
functions.
Change-Id: Ifb50a5207e8cecef1c80d86e2de4d70ab6bf8b8b
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Use a timeout during IO compensation enable function, when
waiting for ready status. If timeout expires, print a warning
message, to indicate that the SoC recommendation is not followed.
Change-Id: I98c7dcb1364b832f4f4b5fc9a0b85a3741a8af4b
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Added some RCPM2 register offset definiton for register: IPSTPCR,
IPSTPACKR and POWMGTDCR, also added OVRD bit definiton of register
POWMGTDCR.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I301bc1401e053c2089b5eb3672c6e649c805a2ab
total_dram_size should be signed value because it is equal to return
value of init_ddr(), so if it is lower or equal zero, report
error as DDR is not initialized correctly.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: Idbc40da103f60f10cb18c5306e97b764c1a9d372
Add helper function to disable the load-store prefetch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I36d7be37e0b800ab1e5842a56cfd04d779338868
* changes:
feat(stm32mp1): enable BL2_IN_XIP_MEM to remove relocation sections
refactor(stm32mp1): reduce MMU memory regions and split XLAT by context
feat(st): map 2MB for ROM code
fix(stm32mp1): restrict DEVICE2 mapping in BL2
Total Compute has ETE and TRBE tracing components and they have
to be enabled to capture the execution trace of the processor.
Signed-off-by: Davidson K <davidson.kumaresan@arm.com>
Change-Id: I3c86c11be2c655a61ecefa3eb2e4e3951577a113
Because the BL2 is not relocated, the usage of BL2_IN_XIP_MEM
can be used. It reduces the binary size by removing all relocation
sections. XIP will not be used when STM32MP_USE_STM32IMAGE is
defined. Introduce new definitions for SEPARATE_CODE_AND_RODATA.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Ifd76f14e5bc98990bf84e0bfd4ee0b4e49a9a293
Simplify the BL2 MMU mapping and reduce the memory regions
number. Split the XLAT define between BL2 and BL32 as binaries
do not share the same tables anymore.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Iaf09e72b4cc29acbe376f6f1cd2a8116c793ba26
This allows reducing MMU tables, and as there is nothing after ROM code
in memory mapping, this has no impact.
Change-Id: If51facb96a523770465cb06eb1ab400f75d26db3
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Only NAND memory map area can be of interest for BL2 in the
DEVICE2 area. Map DEVICE2 under STM32MP_RAW_NAND flag.
Change-Id: I7e3b39579e4a2525b25cb1987d6ec38038d0de2b
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change BL31 load address to 0x970000. This was done by Change-Id
I96d572fc. But then changed back to 0x960000 by Change-Id I8308c629.
However, 0x970000 is the correct value thus we change it back again.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Change-Id: Ia0db4877123b89072f723d18e2bcce25ef38f47d
Disabled CRYPTO_SUPPORT option for Renesas platform as it does not
follow the TF-A authentication mechanism where Trusted-Boot mandates
Crypto module support.
Change-Id: I3aa771e983e3dde083dd8a861f25c0714ffd707f
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
As Measured-Boot and Trusted-Boot are orthogonal, removed
Trusted-Boot's dependency on Measured-Boot by allowing them
to apply the Crypto module changes independently using the
CRYPTO_SUPPORT build flag.
Change-Id: I5a420e5d84f3fefe0c0092d822dab981e6390bbf
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
* changes:
refactor(st-ddr): move basic tests in a dedicated file
refactor(st-ddr): reorganize generic and specific elements
feat(stm32mp1): allow configuration of DDR AXI ports number
refactor(st-ddr): update parameter array initialization
feat(st-ddr): add read valid training support
refactor(stm32mp1): remove the support of calibration result
fix(st-ddr): correct DDR warnings
As the UART is already initialized, no need to check for UART clock
or reset in next BL. An issue can appear if the next BL device tree
(e.g HW_CONFIG) doesn't use the same clocks or resets (like SCMI ones).
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I044ef2386abe2d3dba5a53c3685440d64ca50a4f
This patch includes the errata workaround for erratum
1868343 for the Morello platform.
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
Change-Id: Ifea8148e10946db2276560f90bf2f32bf12b9dcc
* changes:
feat(plat/rcar3): update IPL and Secure Monitor Rev.3.0.3
feat(plat/rcar3): modify type for Internal function argument
feat(plat/rcar3): modify sequence for update value for WUPMSKCA57/53
fix(plat/rcar3): fix to bit operation for WUPMSKCA57/53
These basic tests are generic and should be used independently of the
driver, depending on the plaftorm characteristics.
Change-Id: I38161b659ef2a23fd30a56e1c9b1bd98461a2fe4
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@foss.st.com>
stm32mp_ddrctl structure contains DDRCTRL registers definitions.
stm32mp_ddr_info contains general DDR information extracted from DT.
stm32mp_ddr_size moves to the generic side.
stm32mp1_ddr_priv contains platform private data.
stm32mp_ddr_dt_get_info() and stm32mp_ddr_dt_get_param() allow to
retrieve data from DT. They are located in new generic c/h files in
which stm32mp_ddr_param structure is declared. Platform makefile
is updated.
Adapt driver with this new classification.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Change-Id: I4187376c9fff1a30e7a94407d188391547107997
A new flag STM32MP_DDR_DUAL_AXI_PORT is added, and enabled by default.
It will allow choosing single or dual AXI ports for DDR.
Change-Id: I48826a66a6f4d18df87e081c0960af89ddda1b9d
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Refactor the GPIO code to use a small lookup table instead of redundant or
repetitive code.
Signed-off-by: Jona Stubbe <tf-a@jona-stubbe.de>
Change-Id: Icf60385095efc1f506e4215d497b60f90e16edfd
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
On closed chips, it is not allowed to open debug. The BSEC debug
register can not be rewritten.
On open chips, the debug is already open, no need to rewrite this
register. This part of code is just removed.
An INFO message is displayed if debug is disabled.
The freeze of the watchdog during debug is also removed.
In case of debug, this must be managed by the software that enables
the debugger.
Change-Id: I19fbd3c487bb1018db30fd599cfa94fe5090899f
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Add function headers to improve readability.
Add asserts when required.
Use RCC_BASE address.
Change-Id: Ia545293f00167b6276331a986ea7aa08c006e004
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
According to ST Application note AN5256 [1], the minimum reset pulse
duration should be set to 31ms on boards powered with discrete
regulators.
[1] https://www.st.com/resource/en/application_note/dm00561921.pdf
Change-Id: Ib6ed029ee8a4b95f75a80948fdd2154b4ebe484f
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
We don't use mbox drivers which are implemented in these files for
mcdi, so remove related files from mcdi folder.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Idea5ebe5b25f91066ebd653cdcdafe65ca292b0f
For somewhat historical reasons we are doing some initial PMIC regulator
setup in BL31, as U-Boot does not (yet) have a PMIC driver. This worked
fine so far, but there is at least one board (OrangePi 3) that gets upset,
because the Ethernet PHY needs some *coordinated* bringup of *two*
regulators.
To avoid custom hacks, let's introduce a build option to keep doing the
regulator setup in TF-A. Defining SUNXI_SETUP_REGULATORS to 0 will break
support for some devices on some boards in U-Boot (Ethernet and HDMI),
but will allow to bring up the OrangePi 3 in Linux correctly. We keep
the default at 1 to not change the behaviour for all other boards.
After U-Boot gained proper PMIC support at some point in the future, we
will probably change the default to 0, to get rid of the less optimal
PMIC code in TF-A.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Change-Id: Ie8e2583d0396f6eeaae8ffe6b6190f27db63e2a7
Use regulator framework to get CPU and VDD power supplies.
Change-Id: Ice745fb21ff10e71ef811e747165499c2e19253e
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
print_pmic_info_and_debug() prints the PMIC version ID and displays
regulator information if debug is enabled.
It is under DEBUG flag and called after initialize_pmic() in BL2.
Change-Id: Ib81a625740b7ec6abb49cfca05e44c69efaa4718
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
SYSCFG can be initialized later, after console is up, to display the
warnings or messages it could issue.
PMIC should be initialized earlier, before SYSCFG init.
Change-Id: Icc3a1366083a1b1fde7f0e173645449b4c04c49b
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This is mainly a clock interface with clk_ops callbacks.
Those callbacks are: enable, disable, get_rate, set_parent,
and is_enabled.
This framework is compiled for STM32MP1.
Change-Id: I5119a2aeaf103ceaae7a60d9e423caf0c148d794
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Currently only UART0 is handled as console device, fix the
code to support UART1 as console also.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: Ifcd3c331cf6ce4afb0074357c92fc4addb9438b6
Currently only UART0 is handled as console device, fix the
code to support UART1 as console also.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I08f69b65b78b967ceb7159f4a467aa5982b1f791
Add MCDI related drivers to handle CPU powered on/off in CPU suspend.
TEST=build pass
BUG=b:202871018
Change-Id: I85aaaf3a0e992a39d17c58f3d9d5ff1b5770f748
Signed-off-by: Garmin.Chang <Garmin.Chang@mediatek.com>
Implement PSCI platform operations to support CPU hotplug and MCDI.
TEST=bringup 8 CPUs successfully on kernel stage.
BUG=b:202871018
Change-Id: Ibd5423b70b3ca3f91edaa48d7ca5bc094e751510
Signed-off-by: Garmin.Chang <Garmin.Chang@mediatek.com>
In mt8186 suspend/resume flow, ATF has to communicate with a subsys by
read/write the subsys registers. However, the register region of subsys
doesn't include in the MMU mapping region. It triggers MMU faults.
This patch extends the MMU region 0 size to cover all mt8186 HW modules.
This patch also remove MMU region 1 because region 0 covers region 1.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I520c51338578bd68756cd02603ce6783f93daf51
DCM means dynamic clock management, and it can dynamically
slow down or gate clocks during CPU or bus idle.
1. Add MCUSYS related DCM drivers.
2. Enable MCUSYS related DCM by default.
TEST=build pass
BUG=b:202871018
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Change-Id: Idc669364c89cde0974d2940bd12987ee833d1965
EMI MPU stands for external memory interface memory protect unit.
MT8186 supports 32 regions and 16 domains.
We add basic driver currently, and will add more settings for
EMI MPU in next patch.
TEST=build pass
BUG=b:202871018
Signed-off-by: Penny Jan <penny.jan@mediatek.corp-partner.google.com>
Change-Id: Ia9e5030164e40e060a05e8f91d2ac88258c2e98e
Warnings about header files include order were triggered by CI.
Correct the include order to mathc CI requirements.
Change-Id: Iaca959add924e0e1fa2e56fab2348f0ee36e5fa7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Cortex X2 erratum 2083908 is a Cat B erratum present in the Cortex
X2 core. It applies to revision r2p0 and is still open.
SDEN can be found here:
https://developer.arm.com/documentation/SDEN1775100
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Id9dca2b042bf48e75fb3013ab37d1c5925824728
SoC UART1 is internally connected to MCP UART1 so this
cannot be used as AP runtime UART instead we use the
IOFPGA UART0 as the AP runtime UART.
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Change-Id: Iecefb0d2cb875b3ecf97e0983b06f6e914835021
This patch adds support to load nt_fw_config
with the information from plat_info sds
structure which is then passed from BL2 to BL33.
Signed-off-by: sah01 <sahil@arm.com>
Change-Id: I2242da7404c72a4f9c2e3d7f3b5c154890a78526
Different platform_info sds struct definition will be used
for fvp and soc.
Signed-off-by: sahil <sahil@arm.com>
Change-Id: I92f0e1b2d0d755ad0405ceebfeb78d6e4c67013d
This patch adds all SOC and FVP related changes required to boot
a standard TBBR style boot on Morello.
Signed-off-by: sahil <sahil@arm.com>
Change-Id: Ib8f7f326790b13082cbe8db21a980e048e3db88c
Nicolas Le Bayon
Yann Gautier
Nicolas Toromanoff
Patrick Delaunay
Gabriel Fernandez
Varun Wadekar
Madhukar Pappireddy
Lionel Debieve
Lionel Debieve
Sebastien Pasdeloup
Bipin Ravi
Wasim Khan
Manish V Badarkhe
Manish Pandey
Pali Rohár
Rex-BC Chen
Uwe Kleine-König
Joanna Farley
Olivier Deprez
Juan Pablo Conde
Rohit Mathew
Imre Kis
Michal Simek
Boon Khai Ng
Sieu Mun Tang
Abdul Halim, Muhammad Hadi Asyrafi
Venkatesh Yadav Abbarapu
Yann Gautier
Ravi Patel
Ronak Jain
Nava kishore Manne
Rajan Vaja
Sandrine Bailleux
jason-ch chen
Tamas Ban
Siew Chin Lim
Jiafei Pan
Federico Recanati
Tony K Nadackal
Satish Kumar
Emekcan Aras
Arpita S.K
Vishnu Banavath
Ying-Chun Liu (PaulLiu)
Nicolas Toromanoff
Giulio Benetti
Aditya Angadi
Stephan Gerhold
Fabien Dessenne
Jayanth Dodderi Chidanand
Sughosh Ganu
Takuya Sakata
Etienne Carriere
Davidson K
Ying-Chun Liu (PaulLiu)
Manoj Kumar
Nicolas Le Bayon
Jona Stubbe
André Przywara
Pascal Paillet
Garmin.Chang
Yuchen Huang
Edward-JW Yang
Guodong Liu
Zhengnan Chen
Christine Zhu
James Lo
Penny Jan
johpow01
Chandni Cherukuri
sah01