Using the Fconf, register base address of the various nv-counters
(currently, trusted, non-trusted nv-counters) are moved to the
device tree and retrieved during run-time. This feature is
enabled using the build option COT_DESC_IN_DTB.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I236f532e63cea63b179f60892cb406fc05cd5830
'EHF' is used by RAS, SDEI, SPM_MM common frameworks.
If platform needs to plug-in specific handlers then
'PLAT_EHF_DESC' can be used to populate platform specific
priority levels.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Change-Id: I37af7e0e48111f87b6982604bf5c15db3e05755d
Allocated 512-959 SPI numbers for remote n1sdp chip and same has been
referenced for GIC routing table.
Change-Id: Id79ea493fd665ed93fe9644a59e363ec10441098
Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com>
Add information about the third partition so it can be loaded into SPM
when running the tests
Signed-off-by: Ruari Phipps <ruari.phipps@arm.com>
Change-Id: I5544e88df391ef294ddf6b5750d468d3e74892b1
In case of AT speculative workaround applied, page table walk
is disabled for lower ELs (EL1 and EL0) in EL3.
Hence added a wrapper function which temporarily enables page
table walk to execute AT instruction for lower ELs and then
disables page table walk.
Execute AT instructions directly for lower ELs (EL1 and EL0)
assuming page table walk is enabled always when AT speculative
workaround is not applied.
Change-Id: I4ad4c0bcbb761448af257e9f72ae979473c0dde8
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Implemented platform functions to retrieve the soc-id information
for juno platform
Change-Id: Ie677120710b45e202a2d63a954459ece8a64b353
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Implemented platform functions to retrieve the soc-id information
for FVP platform.
Change-Id: Id3df02ab290a210310e8d34ec9d706a59d817517
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Removed common code for soc-id feature which is applicable
for all arm platforms.
In subsequent patches, added a platform based functions
for FVP and Juno to retrieve the soc-id information.
Change-Id: Idb632a935758a6caff2ca03a6eab8f663da8a93a
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
SP804 TIMER is not platform specific, and current code base adds
multiple defines to use this driver. Like FVP_USE_SP804_TIMER and
FVP_VE_USE_SP804_TIMER.
This patch removes platform specific build flag and adds generic
flag `USE_SP804_TIMER` to be set to 1 by platform if needed.
Change-Id: I5ab792c189885fd1b98ddd187f3a38ebdd0baba2
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
* changes:
SPM: Add owner field to cactus secure partitions
SPM: Alter sp_gen.mk entry depending on owner of partition
plat/arm: enable support for Plat owned SPs
For supporting dualroot CoT for Secure Partitions a new optional field
"owner" is introduced which will be used to sign the SP with
corresponding signing domain. To demonstrate its usage, this patch adds
owners to cactus Secure Partitions.
Signed-off-by: Ruari Phipps <ruari.phipps@arm.com>
Change-Id: I7b760580355fc92edf5402cecc38c38125dc1cae
For Arm platforms SPs are loaded by parsing tb_fw_config.dts and
adding them to SP structure sequentially, which in-turn is appended to
loadable image list.
With recently introduced dualroot CoT for SPs where they are owned
either by SiP or by Platform. SiP owned SPs index starts at SP_PKG1_ID
and Plat owned SPs index starts at SP_PKG5_ID. As the start index of SP
depends on the owner, there should be a mechanism to parse owner of a SP
and put it at the correct index in SP structure.
This patch adds support for parsing a new optional field "owner" and
based on it put SP details(UUID & Load-address) at the correct index in
SP structure.
Change-Id: Ibd255b60d5c45023cc7fdb10971bef6626cb560b
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
This resolves MISRA defects such as:
plat/common/plat_bl1_common.c:63:[MISRA C-2012 Rule 14.4 (required)]
The condition expression "1" does not have an essentially boolean type.
Change-Id: I679411980ad661191fbc834a44a5eca5494fd0e2
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
There was a collision between the name of the typedef in the CASSERT and
something else, so we make the name of the typedef unique to the
invocation of DEFFINE_SVC_UUID2 by appending the name that's passed into
the macro. This eliminates the following MISRA violation:
bl1/bl1_main.c:233:[MISRA C-2012 Rule 5.6 (required)] Identifier
"invalid_svc_uuid" is already used to represent a typedef.
This also resolves MISRA rule 5.9.
These renamings are as follows:
* tzram -> secram. This matches the function call name as it has
sec_mem in it's name
* fw_config_base -> config_base. This file does not mess with
hw_conig, so there's little chance of confusion
Change-Id: I8734ba0956140c8e29b89d0596d10d61a6ef351e
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
BL31 binary size is aligned to 4KB because of the
code in include\plat\arm\common\arm_reclaim_init.ld.S:
__INIT_CODE_UNALIGNED__ = .;
. = ALIGN(PAGE_SIZE);
__INIT_CODE_END__ = .;
with all the zero data after the last instruction of
BL31 code to the end of the page.
This causes increase in size of BL31 binary stored in FIP
and its loading time by BL2.
This patch reduces the size of BL31 image by moving
page alignment from __INIT_CODE_END__ to __STACKS_END__
which also increases the stack size for secondary CPUs.
Change-Id: Ie2ec503fc774c22c12ec506d74fd3ef2b0b183a9
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Currently only single signing domain is supported for SP packages but
there is plan to support dual signing domains if CoT is dualroot.
SP_CONTENT_CERT_ID is the certificate file which is currently generated
and signed with trusted world key which in-turn is derived from Silicon
provider RoT key.
To allow dual signing domain for SP packages, other certificate file
will be derived from Platform owned RoT key.
This patch renames "SP_CONTENT_CERT_ID" to "SIP_SP_CONTENT_CERT_ID" and
does other related changes.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I0bc445a3ab257e2dac03faa64f46e36a9fed5e93
Following merge of patchset [1] the spm_mm_boot_info_t structure is
included in few platform files unconditionally even when SPM_MM option
is disabled.
[1] https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/2647
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I68bc034c9348b5d9bcfd2e5217b781df5ad1b369
The command line for BL33 payloads is typically taken from the DTB. On
"normal" systems the bootloader will put the right version in there, but
we typically don't use one on the FPGAs.
To avoid editing (and possibly re-packaging) the DTB for every change in
the command line, try to read it from some "magic" memory location
instead. It can be easily placed there by the tool that uploads the
other payloads to the FPGA's memory. BL31 will then replace the existing
command line in the DTB with that new string.
To avoid reading garbage, check the memory location for containing a
magic value. This is conveniently chosen to be a simple ASCII string, so
it can just preceed the actual command line in a text file:
--------------------------------
CMD:console=ttyAMA0,38400n8 debug loglevel=8
--------------------------------
Change-Id: I5923a80332c9fac3b4afd1a6aaa321233d0f60da
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Provide manifest and build options to boot OP-TEE as a
guest S-EL1 Secure Partition on top of Hafnium in S-EL2.
Increase ARM_SP_MAX_SIZE to cope with OP-TEE debug build image.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Idd2686fa689a78fe2d05ed92b1d23c65e2edd4cb
This patch fixes a bug where wrong panic was caused when the number
of SP was same as max limit.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I9ace62d8d5bcdc410eeacdd9d33d55a7be5fcc8e
Currently, soc-revision information is not available for arm
platforms hence disabled 'SMCCC_ARCH_SOC_ID' feature for all arm
platforms.
Change-Id: I1ab878c6a4c8fecfff63bc6dde83e3ecefe20279
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
SPM(BL32) and hafnium(BL33) expect their manifest base address in x0
register, which is updated during BL2 stage by parsing fw_config.
In case of RESET_TO_BL31 it has to be updated while populating
entry point information.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I6f4a97f3405029bd6ba25f0935e2d1f74bb95517
As secondary cores show up, they populate an array to
announce themselves so plat_core_pos_by_mpidr() can
return an invalid COREID code for any non-existing
MPIDR that it is queried about.
The Power Domain Tree Description is populated with
a topology based on the maximum harcoded values.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I8fd64761a2296714ce0f37c46544f3e6f13b5f61
In BL2, fw_config's population happened before the cache gets
enabled.
Hence to boost the performance, moved fw_config's population
after cache gets enabled (i.e. after MMU gets enabled).
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I2e75cabd76b1cb7a660f6b72f409ab40d2877284
Updated the function 'set_fw_config_info' to make it generic
by doing below changes:
1. Rename function name from 'set_fw_config_info' to 'set_config_info'
2. Take image_id as an argument so that this function can set any
config information.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Icf29e19d3e9996d8154d84dbbbc76712fab0f0c1
Update the data type of the member 'config_max_size' present in the
structure 'dyn_cfg_dtb_info_t' to uint32_t.
This change is being done so that dyn_cfg_dtb_info_t and image_info
structure should use same data type for maximum size.
Change-Id: I9b5927a47eb8351bbf3664b8b1e047ae1ae5a260
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Currently, the need for firmware update is being checked twice
in the code hence modifications are done to do this check only
once and set the global variable.
Then this global variable helps to decide whether to go for
normal boot or firmware update flow.
Change-Id: I8469284555a8039786f34670f9dc4830f87aecc1
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Renamed node for trusted boot fw config from 'plat_arm_bl2' to
'tb_fw-config'.
Change-Id: I2e16b6f4d272292ec1855daafd014e851436dd9b
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
This patch adds support for Measured Boot functionality
to FVP platform code. It also defines new properties
in 'tpm_event_log' node to store Event Log address and
it size
'tpm_event_log_sm_addr'
'tpm_event_log_addr'
'tpm_event_log_size'
in 'event_log.dtsi' included in 'fvp_tsp_fw_config.dts'
and 'fvp_nt_fw_config.dts'. The node and its properties
are described in binding document
'docs\components\measured_boot\event_log.rst'.
Change-Id: I087e1423afcb269d6cfe79c1af9c348931991292
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch adds support for Event Log generation required
for Measured Boot functionality.
Change-Id: I34f05a33565e6659e78499d62cc6fb00b7d6c2dc
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch adds support for Measured Boot driver functionality
in common Arm platform code.
Change-Id: If049dcf8d847c39023b77c0d805a8cf5b8bcaa3e
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
TBBR authentication framework depends on the plat_get_rotpk_info()
function to return the pointer to the Root of Trust Public Key (ROTPK)
stored in the platform along with its length. Add this function for
RD-Daniel Config-XLR platform to support Trusted Board Boot. The
function makes use of the wrapper function provided by the arm common
trusted board boot function to get the ROTPK hash.
Change-Id: I509e2f7e88cc2167e1732a971d71dc131d3d4b01
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
TBBR authentication framework depends on the plat_get_rotpk_info()
function to return the pointer to the Root of Trust Public Key (ROTPK)
stored in the platform along with its length. Add this function for
RD-Daniel platform to support Trusted Board Boot. The function makes use
of the wrapper function provided by the arm common trusted board boot
function to get the ROTPK hash.
Change-Id: I6c2826a7898664afea19fd62432684cfddd9319a
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
This patch moves all GICv2 driver files into new added
'gicv2.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
NOTE: Usage of 'drivers/arm/gic/common/gic_common.c' file
is now deprecated and platforms with GICv2 driver need to
be modified to include 'drivers/arm/gic/v2/gicv2.mk' in
their makefiles.
Change-Id: Ib10e71bdda0e5c7e80a049ddce2de1dd839602d1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
BL2 size gets increased due to the libfdt library update and
that eventually cause no-optimization build failure for BL2 as below:
aarch64-none-elf-ld.bfd: BL2 image has exceeded its limit.
aarch64-none-elf-ld.bfd: region `RAM' overflowed by 4096 bytes
Makefile:1070: recipe for target 'build/fvp/debug/bl2/bl2.elf' failed
make: *** [build/fvp/debug/bl2/bl2.elf] Error 1
Fixed build failure by increasing BL2 image size limit by 4Kb.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I92a57eb4db601561a98e254b64994bb921a88db3
Included cot_descriptors.dtsi in platform device tree
(fvp_tb_fw_config.dts).
Also, updated the maximum size of tb_fw_config to 0x1800
in order to accomodate the device tree for CoT descriptors.
Follow up patch will parse the device tree for these CoT descriptors
and fill the CoT descriptor structures at runtime instead of using
static CoT descriptor structures in the code base.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I90122bc713f6842b82fb019b04caf42629b4f45a
The memory layout for the FPGA is fairly uniform for most of the FPGA
images, and we already assume that DRAM starts at 2GB by default.
Prepopulate PRELOADED_BL33_BASE and FPGA_PRELOADED_DTB_BASE to some
sane default values, to simplify building some stock image.
If people want to deviate from that, they can always override those
addresses on the make command line.
Change-Id: I2238fafb3f8253a01ad2d88d45827c141d9b29dd
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To support FPGAs with those cores as well, as the respective cpulib
files to the Makefile.
Change-Id: I1a60867d5937be88b32b210c7817be4274554a76
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The maximum number of clusters is currently set to 2, which is quite
limiting. As there are FPGA images with 4 clusters, let's increase the
limit to 4.
Change-Id: I9a85ca07ebbd2a018ad9668536d867ad6b75e537
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch performs the following:
- Creating two corstone700 platforms under corstone700 board:
fvp and fpga
- Since the FVP and FPGA have IP differences, this commit provides a specific DTS for each platform
- The platform can be specified using the TARGET_PLATFORM Makefile variable
(possible values are: fvp or fpga)
- Allowing to use u-boot by:
- Enabling NEED_BL33 option
- Fixing non-secure image base: For no preloaded bl33 we want to
have the NS base set on shared ram. Setup a memory map region
for NS in shared map and set the bl33 address in the area.
- Setting the SYS_COUNTER_FREQ_IN_TICKS based on the selected
platform
- Setting ARM_MAP_SHARED_RAM and ARM_MAP_NS_SHARED_RAM to use MT_MEMORY
Change-Id: I4c8ac3387acb1693ab617bcccab00d80e340c163
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Added assert in the code to check valid address of dtb information
structure retrieved from fw_config device tree.
This patch fixes coverity defect:360213.
Also, removed conditional calling of "fconf_populate" as "fconf_populate"
function already checks the validity of the device tree address received
and go to panic in case of address is NULL.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ib83e4e84a95e2456a12c7a2bb3fe70461d882cba
This version corresponds to the following commit <7be250b>
libfdt: Correct condition for reordering blocks
Also, updated the Juno romlib jumptable with fdt APIs.
Change-Id: Ib6d28c1aea81c2144a263958f0792cc4daea7a1f
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
The plat_core_pos_by_mpidr() implementation for the Arm FPGA port has
some issues, which leads to problems when matching GICv3 redistributors
with cores:
- The power domain tree was not taking multithreading into account, so
we ended up with the wrong mapping between MPIDRs and core IDs.
- Before even considering an MPIDR, we try to make sure Aff2 is 0.
Unfortunately this is the cluster ID when the MT bit is set.
- We mask off the MT bit in MPIDR, before basing decisions on it.
- When detecting the MT bit, we are properly calculating the thread ID,
but don't account for the shift in the core and cluster ID checks.
Those problems lead to early rejections of MPIDRs values, in particular
when called from the GIC code. As a result, CPU_ON for secondary cores
was failing for most of the cores.
Fix this by properly handling the MT bit in plat_core_pos_by_mpidr(),
also pulling in FPGA_MAX_PE_PER_CPU when populating the power domain
tree.
Change-Id: I71b2255fc0d27bfe5806511df479ab38e4e33fc4
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Passed the address of fw_config instead of soc_fw_config
as arg1 to BL31 from BL2 for ARM fvp platform.
BL31 then retrieve load-address of other device trees
from fw_config device tree.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ib7e9581cd765d76111dcc3b7e0dafc12503c83c1
* changes:
doc: Update memory layout for firmware configuration area
plat/arm: Increase size of firmware configuration area
plat/arm: Load and populate fw_config and tb_fw_config
fconf: Handle error from fconf_load_config
plat/arm: Update the fw_config load call and populate it's information
fconf: Allow fconf to load additional firmware configuration
fconf: Clean confused naming between TB_FW and FW_CONFIG
tbbr/dualroot: Add fw_config image in chain of trust
cert_tool: Update cert_tool for fw_config image support
fiptool: Add fw_config in FIP
plat/arm: Rentroduce tb_fw_config device tree
Increased the size of firmware configuration area to accommodate
all configs.
Updated maximum size of following bootloaders due to increase
in firmware configs size and addition of the code in the BL2.
1. Increased maximum size of BL2 for Juno platform in no
optimisation case.
2. Reduced maximum size of BL31 for fvp and Juno platform.
3. Reduced maximum size of BL32 for Juno platform.
Change-Id: Ifba0564df0d1fe86175bed9fae87fdcf013b1831
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Modified the code to do below changes:
1. Load tb_fw_config along with fw_config by BL1.
2. Populate fw_config device tree information in the
BL1 to load tb_fw_config.
3. In BL2, populate fw_config information to retrieve
the address of tb_fw_config and then tb_fw_config
gets populated using retrieved address.
4. Avoid processing of configuration file in case of error
value returned from "fw_config_load" function.
5. Updated entrypoint information for BL2 image so
that it's arg0 should point to fw_config address.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change-Id: Ife6f7b673a074e7f544ee3d1bda7645fd5b2886c
Query clock frequency in runtime using FCONF getter API
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: Ie6a8a62d8d190b9994feffb167a1d48829913e9b
Extract Timer clock frequency from the timer node in
HW_CONFIG dtb. The first timer is a per-core architected timer attached
to a GIC to deliver its per-processor interrupts via PPIs.
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I2f4b27c48e4c79208dab9f03c768d9221ba6ca86
Modified the code to do below changes:
1. Migrates the Arm platforms to the API changes introduced in the
previous patches by fixing the fconf_load_config() call.
2. Retrieve dynamically the address of tb_fw_config using fconf
getter api which is subsequently used to write mbedTLS heap
address and BL2 hash data in the tb_fw_config DTB.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change-Id: I3c9d9345dcbfb99127c61d5589b4aa1532fbf4be
Cleaned up confused naming between TB_FW and FW_CONFIG.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I9e9f6e6ca076d38fee0388f97d370431ae067f08
Moved BL2 configuration nodes from fw_config to newly
created tb_fw_config device tree.
fw_config device tree's main usage is to hold properties shared
across all BLx images.
An example is the "dtb-registry" node, which contains the
information about the other device tree configurations
(load-address, size).
Also, Updated load-address of tb_fw_config which is now located
after fw_config in SRAM.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ic398c86a4d822dacd55b5e25fd41d4fe3888d79a
Load address of tb_fw_config is incorrectly mentioned
in below device trees:
1. rdn1edge_fw_config.dts
2. tc0_fw_config.dts
Till now, tb_fw_config load-address is not being retrieved from
device tree and hence never exeprienced any issue for tc0 and
rdn1edge platform.
For tc0 and rdn1edge platform, Load-address of tb_fw_config should
be the SRAM base address + 0x300 (size of fw_config device tree)
Hence updated these platform's fw_config.dts accordingly to reflect
this load address change.
Change-Id: I2ef8b05d49be10767db31384329f516df11ca817
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Using the fconf framework, the Group 0 and Group 1 secure interrupt
descriptors are moved to device tree and retrieved in runtime. This
feature is enabled by the build flag SEC_INT_DESC_IN_FCONF.
Change-Id: I360c63a83286c7ecc2426cd1ff1b4746d61e633c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.
This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.
Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
A new certificate "sip-sp-cert" has been added for Silicon Provider(SiP)
owned Secure Partitions(SP). A similar support for Platform owned SP can
be added in future. The certificate is also protected against anti-
rollback using the trusted Non-Volatile counter.
To avoid deviating from TBBR spec, support for SP CoT is only provided
in dualroot.
Secure Partition content certificate is assigned image ID 31 and SP
images follows after it.
The CoT for secure partition look like below.
+------------------+ +-------------------+
| ROTPK/ROTPK Hash |------>| Trusted Key |
+------------------+ | Certificate |
| (Auth Image) |
/+-------------------+
/ |
/ |
/ |
/ |
L v
+------------------+ +-------------------+
| Trusted World |------>| SiP owned SPs |
| Public Key | | Content Cert |
+------------------+ | (Auth Image) |
/ +-------------------+
/ |
/ v|
+------------------+ L +-------------------+
| SP_PKG1 Hash |------>| SP_PKG1 |
| | | (Data Image) |
+------------------+ +-------------------+
. .
. .
. .
+------------------+ +-------------------+
| SP_PKG8 Hash |------>| SP_PKG8 |
| | | (Data Image) |
+------------------+ +-------------------+
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ia31546bac1327a3e0b5d37e8b99c808442d5e53f
As per "include/export/README", TF-A code should never include export
headers directly. Instead, it should include a wrapper header that
ensures the export header is included in the right manner.
"tbbr_img_def_exp.h" is directly included in TF-A code, this patch
replaces it with its wrapper header "tbbr_img_def.h".
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I31c1a42e6a7bcac4c396bb17e8548567ecd8147d
This should allow git to easily track file moves
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Change-Id: I1592cf39a4f94209c560dc6d1a8bc1bfb21d8327
This patch adds support for Total Compute (TC0) platform. It is an
initial port and additional features are expected to be added later.
TC0 has a SCP which brings the primary Cortex-A out of reset
which starts executing BL1. TF-A optionally authenticates the SCP
ram-fw available in FIP and makes it available for SCP to copy.
Some of the major features included and tested in this platform
port include TBBR, PSCI, MHUv2 and DVFS.
Change-Id: I1675e9d200ca7687c215009eef483d9b3ee764ef
Signed-off-by: Usama Arif <usama.arif@arm.com>
Fixed build error for dualroot chain of trust.
Build error were thrown as below while compiling the code for
dualroot chain of trust:
aarch64-none-elf-ld.bfd: ./build/fvp/debug/bl1/tbbr_cot_bl1.o:
(.bss.auth_img_flags+0x0): multiple definition of `auth_img_flags';
./build/fvp/debug/bl1/cot.o:(.bss.auth_img_flags+0x0): first defined here
aarch64-none-elf-ld.bfd: ./build/fvp/debug/bl1/tbbr_cot_bl1.o:
(.rodata.cot_desc_size+0x0): multiple definition of `cot_desc_size';
./build/fvp/debug/bl1/cot.o:(.rodata.cot_desc_size+0x0): first defined here
aarch64-none-elf-ld.bfd: ./build/fvp/debug/bl1/tbbr_cot_bl1.o:
(.rodata.cot_desc_ptr+0x0): multiple definition of `cot_desc_ptr';
./build/fvp/debug/bl1/cot.o:(.rodata.cot_desc_ptr+0x0): first defined here
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I1a426c4e7f5f8013d71dafc176c7467c1b329757
SPCI is renamed as PSA FF-A which stands for Platform Security
Architecture Firmware Framework for A class processors.
This patch replaces the occurrence of SPCI with PSA FF-A(in documents)
or simply FFA(in code).
Change-Id: I4ab10adb9ffeef1ff784641dfafd99f515133760
Signed-off-by: J-Alves <joao.alves@arm.com>
We query the UART base address and clk frequency in runtime
using fconf getter APIs.
Change-Id: I5f4e84953be5f384472bf90720b706d45cb86260
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
This patch introduces the populate function which leverages
a new driver to extract base address and clk frequency properties
of the uart serial node from HW_CONFIG device tree.
This patch also introduces fdt helper API fdtw_translate_address()
which helps in performing address translation.
Change-Id: I053628065ebddbde0c9cb3aa93d838619f502ee3
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Query the GICD and GICR base addresses in runtime using fconf getter
APIs.
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I309fb2874f3329ddeb8677ddb53ed4c02199a1e9
CoT used for BL1 and BL2 are moved to tbbr_cot_bl1.c
and tbbr_cot_bl2.c respectively.
Common CoT used across BL1 and BL2 are moved to
tbbr_cot_common.c.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I2252ac8a6960b3431bcaafdb3ea4fb2d01b79cf5
This patch introduces dynamic configuration for SDEI setup and is supported
when the new build flag SDEI_IN_FCONF is enabled. Instead of using C arrays
and processing the configuration at compile time, the config is moved to
dts files. It will be retrieved at runtime during SDEI init, using the fconf
layer.
Change-Id: If5c35a7517ba00a9f258d7f3e7c8c20cee169a31
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Co-authored-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
* changes:
arm_fpga: Read UART address from DT
arm_fpga: Read GICD and GICR base addresses from DT
arm_fpga: Read generic timer counter frequency from DT
arm_fpga: Use Generic UART
The arm_fpga port requires a DTB, to launch a BL33 payload.
To make this port more flexible, we can also use the information in the
DT to configure the console driver.
For a start, find the DT node pointed to by the stdout-path property, and
read the base address from there.
This assumes for now that the stdout-path points to a PL011 UART.
This allows to remove platform specific addresses from the image. We
keep the original base address for the crash console.
Change-Id: I46a990de2315f81cae4d7913ae99a07b0bec5cb1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since we use a DTB with all platform information to pass this on to a
kernel loaded as BL33, we can as well make use of it for our own
purposes.
Every DT would contain a node for the GIC(v3) interrupt controller, so
we can read the base address for the distributor and redistributors from
there.
This avoids hard coding this information in the code and allows for a more
flexible binary.
Change-Id: Ic530e223a21a45bc30a07a21048116d5af69e972
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The stdout-path property in the /chosen node of a DTB points to a device
node, which is used for boot console output.
On most (if not all) ARM based platforms this is the debug UART.
The ST platform code contains a function to parse this property and
chase down eventual aliases to learn the node offset of this UART node.
Introduce a slightly more generalised version of this ST platform function
in the generic fdt_wrappers code. This will be useful for other platforms
as well.
Change-Id: Ie6da47ace7833861b5e35fe8cba49835db3659a5
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARM Generic Timer DT binding describes an (optional) property to
declare the counter frequency. Its usage is normally discouraged, as the
value should be read from the CNTFRQ_EL0 system register.
However in our case we can use it to program this register in the first
place, which avoids us to hard code a counter frequency into the code.
We keep some default value in, if the DT lacks that property for
whatever reason.
Change-Id: I5b71176db413f904f21eb16f3302fbb799cb0305
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The STM32 platform port parse DT nodes to find base address to
peripherals. It does this by using its own implementation, even though
this functionality is generic and actually widely useful outside of the
STM32 code.
Re-implement fdt_get_reg_props_by_name() on top of the newly introduced
fdt_get_reg_props_by_index() function, and move it to fdt_wrapper.c.
This is removes the assumption that #address-cells and #size-cells are
always one.
Change-Id: I6d584930262c732b6e0356d98aea50b2654f789d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The SCP firmware on the ARM FPGA initialises the UART already. This allows
us to treat the PL011 as an SBSA Generic UART, which does not require
any further setup.
This in particular removes the need for any baudrate and base clock related
settings to be hard coded into the BL31 image.
Change-Id: I16fc943526267356b97166a7068459e06ff77f0f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment the fconf_populate_gicv3_config() implementation is
somewhat incomplete: First it actually fails to store the retrieved
information (the local addr[] array is going nowhere), but also it makes
quite some assumptions about the device tree passed to it: it needs to
use two address-cells and two size-cells, and also requires all five
register regions to be specified, where actually only the first two
are mandatory according to the binding (and needed by our code).
Fix this by introducing a proper generic function to retrieve "reg"
property information from a DT node:
We retrieve the #address-cells and #size-cells properties from the
parent node, then use those to extract the right values from the "reg"
property. The function takes an index to select one region of a reg
property.
This is loosely based on the STM32 implementation using "reg-names",
which we will subsume in a follow-up patch.
Change-Id: Ia59bfdf80aea4e36876c7b6ed4d153e303f482e8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Dynamic configuration properties are fconf properties. Modify the
compatible string from "arm,.." to "fconf,.." to reflect this.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change-Id: I85eb75cf877c5f4d3feea3936d4c348ca843bc6c
Our fdtw_read_cells() implementation goes to great lengths to
sanity-check every parameter and result, but leaves a big hole open:
The size of the storage the value pointer points at needs to match the
number of cells given. This can't be easily checked at compile time,
since we lose the size information by using a void pointer.
Regardless the current usage of this function is somewhat wrong anyways,
since we use it on single-element, fixed-length properties only, for
which the DT binding specifies the size.
Typically we use those functions dealing with a number of cells in DT
context to deal with *dynamically* sized properties, which depend on
other properties (#size-cells, #clock-cells, ...), to specify the number
of cells needed.
Another problem with the current implementation is the use of
ambiguously sized types (uintptr_t, size_t) together with a certain
expectation about their size. In general there is no relation between
the length of a DT property and the bitness of the code that parses the
DTB: AArch64 code could encounter 32-bit addresses (where the physical
address space is limited to 4GB [1]), while AArch32 code could read
64-bit sized properties (/memory nodes on LPAE systems, [2]).
To make this more clear, fix the potential issues and also align more
with other DT users (Linux and U-Boot), introduce functions to explicitly
read uint32 and uint64 properties. As the other DT consumers, we do this
based on the generic "read array" function.
Convert all users to use either of those two new functions, and make
sure we never use a pointer to anything other than uint32_t or uint64_t
variables directly.
This reveals (and fixes) a bug in plat_spmd_manifest.c, where we write
4 bytes into a uint16_t variable (passed via a void pointer).
Also we change the implementation of the function to better align with
other libfdt users, by using the right types (fdt32_t) and common
variable names (*prop, prop_names).
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi#n874
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/ecx-2000.dts
Change-Id: I718de960515117ac7a3331a1b177d2ec224a3890
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently our fdtw_read_array() implementation requires the length of
the property to exactly match the requested size, which makes it less
flexible for parsing generic device trees.
Also the name is slightly misleading, since we treat the cells of the
array as 32 bit unsigned integers, performing the endianess conversion.
To fix those issues and align the code more with other DT users (Linux
kernel or U-Boot), rename the function to "fdt_read_uint32_array", and
relax the length check to only check if the property covers at least the
number of cells we request.
This also changes the variable names to be more in-line with other DT
users, and switches to the proper data types.
This makes this function more useful in later patches.
Change-Id: Id86f4f588ffcb5106d4476763ecdfe35a735fa6c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
RD-Daniel Config-XLR platform has four identical chips connected via a
high speed coherent CCIX link. Each chip has four Neoverse cores
connected via coherent CMN interconnect.
Change-Id: I37d1b91f2b6ba08f61c64d0288bc16a429836c08
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
This commit fixes an assertion that was triggering in certain contexts:
ERROR: mmap_add_region_check() failed. error -22
ASSERT: lib/xlat_tables_v2/xlat_tables_core.c:790
Change-Id: Ia55b3fb4f496c8cd791ea6093d122edae0a7e92a
Signed-off-by: Chris Kay <chris.kay@arm.com>
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
By writing 0 to CLUSTERPWRDN DSU register bit 0, we send an
advisory to the power controller that cluster power is not required
when all cores are powered down.
The AArch32 CLUSTERPWRDN register is architecturally mapped to the
AArch64 CLUSTERPWRDN_EL1 register
Change-Id: Ie6e67c1c7d811fa25c51e2e405ca7f59bd20c81b
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
A single chip platform requires five mmap entries and a corresponding
number of translation tables. For every additional chip in the system,
three additional mmap entries are required to map the shared SRAM and
the IO regions. A corresponding number of additional translation
tables are required as well.
Change-Id: I1332a1305f2af62181387cf36954f6fb0e6f11ed
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
The arm_fpga platform code contains an dubious line to initialise some
timer. On closer inspection this turn out to be bogus, as this was only
needed on some special (older) FPGA board, and is actually not needed on
the current model. Also the base address was wrong anyways.
Remove the code entirely.
Change-Id: I02e71aea645051b5addb42d972d7a79f04b81106
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
RD-Daniel uses GIC-Clayton as its interrupt controller which is an
implementation of GICv4.1 architecture. Hence for RD-Daniel, enable
GICv4 extension support.
Change-Id: I45ae8c82376f8fe8fc0666306822ae2db74e71b8
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
This patch adds support for GICv4 extension for FVP platform.
Change-Id: Ia389b61266af669b1ca9b999a8b76476cab214f4
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Increased the maximum size of BL2 image in order to
accommodate the BL2 image when TF-A build with no compiler
optimization for ARM platform.
Note: As of now, "no compiler optimization" build works
only when TRUSTED_BOOT_BOARD option is set to 0.
This change is verified using below CI configuration:
1. juno-no-optimize-default:juno-linux.uboot
2. fvp-no-optimize-default,fvp-default:fvp-tftf-fip.tftf-aemv8a-debug
Change-Id: I5932621237f8acd1b510682388f3ba78eae90ea4
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
with commit a6ea06f5, the way platform includes gicv3 files has been
modified, this patch adapts to new method of including gicv3 files
for arm_fpga platform.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ic5ccae842b39b7db06d4f23c5738b174c42edf63
The platform io policies array is now always accessed through a fconf getter.
This gives us an ideal spot to check for out-of-bound accesses.
Remove the assertion in plat_get_image_source(), which is now redundant.
Change-Id: Iefe808d530229073b68cbd164d927b8b6662a217
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
As GCC manual says, -D option defines a macro as 1, if =<value> is omitted.
-D <name>
Predefine <name> as a macro, with definition 1.
The same applied with Clang, too.
In the context of -D option, =1 is always redundant.
Change-Id: I487489a1ea3eb51e734741619c1e65dab1420bc4
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
-D is a preprocessor flag that defines a macro. So, adding it to
BL*_CPPFLAGS makes more sense. You can reference it not only from
.c files but also from .S files.
Change-Id: Ib4f2f27a3ed3eae476a6a32da7ab5225ad0649de
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
1. Necessary changes to platform makefile to include fw_config
device tree and package it in fip.bin
2. Removed hw_config node from fw_config dts as there is no
HW_CONFIG device tree source for sgm775
3. Added mbedtls_heap related properties for TBBR functionality
Change-Id: I26b940c65b17ad2fb5537141f8649785bb0fd4ad
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Moved SMCCC defines from plat_arm.h to new <smccc_def.h> header
and include this header in all ARM platforms.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I4cbc69c7b9307461de87b7c7bf200dd9b810e485
This patch moves all GICv3 driver files into new added
'gicv3.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
The patch adds GICv3 driver configuration flags
'GICV3_IMPL', 'GICV3_IMPL_GIC600_MULTICHIP' and
'GICV3_OVERRIDE_DISTIF_PWR_OPS' described in
'GICv3 driver options' section of 'build-option.rst'
document.
NOTE: Platforms with GICv3 driver need to be modified to
include 'drivers/arm/gic/v3/gicv3.mk' in their makefiles.
Change-Id: If055f6770ff20f5dee5a3c99ae7ced7cdcac5c44
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Use ARRAY_SIZE macro instead of sizeof operator to obtain the maximum
number of SCMI channels supported on the platform.
Change-Id: Id922bb548af98ac99b4ac0c34e38e589e5a80b2d
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
* changes:
plat/arm/board/arm_fpga: Compile with additional CPU libraries
plat/arm/board/arm_fpga: Enable position-independent execution
plat/arm/board/arm_fpga: Enable port for alternative cluster configurations
plat/arm/board/arm_fpga: Initialize the Generic Interrupt Controller
plat/arm/board/arm_fpga: Initialize the System Counter
plat/arm/board/arm_fpga: Add PSCI implementation for FPGA images
plat/arm/board/arm_fpga: Use preloaded BL33 alternative boot flow
plat/arm/board/arm_fpga: Enable basic BL31 port for an FPGA image
This change is part of the goal of enabling the port to be compatible
with multiple FPGA images.
BL31 behaves differently depending on whether or not the CPUs in the
system use cache coherency, and as a result any CPU libraries that are
compiled together must serve processors that are consistent in this
regard.
This compiles a different set of CPU libraries depending on whether or
not the HW_ASSISTED_COHERENCY is enabled at build-time to indicate the
CPUs support hardware-level support for cache coherency. This build
flag is used in the makefile in the same way as the Arm FVP port.
Signed-off-by: Oliver Swede <oli.swede@arm.com>
Change-Id: I18300b4443176b89767015e3688c0f315a91c27e
This allows the BL31 port to run with position-independent execution
enabled so that it can be ran from any address in the system.
This increases the flexibility of the image, allowing it to be ran from
other locations rather than only its hardcoded absolute address
(currently set to the typical DRAM base of 2GB). This may be useful for
future images that describe system configurations with other memory
layouts (e.g. where SRAM is included).
It does this by setting ENABLE_PIE=1 and changing the absolute
address to 0. The load address of bl31.bin can then be specified by
the -l [load address] argument in the fpga-run command (additionally,
this address is required by any preceding payloads that specify the
start address. For ELF payloads this is usually extracted automatically
by reading the entrypoint address in the header, however bl31.bin is a
different file format so has this additional dependency).
Signed-off-by: Oliver Swede <oli.swede@arm.com>
Change-Id: Idd74787796ab0cf605fe2701163d9c4b3223a143
This change is part of the goal of enabling the port to be compatible
with multiple FPGA images.
The BL31 port that is uploaded as a payload to the FPGA with an image
should cater for a wide variety of system configurations. This patch
makes the necessary changes to enable it to function with images whose
cluster configurations may be larger (either by utilizing more
clusters, more CPUs per cluster, more threads in each CPU, or a
combination) than the initial image being used for testing.
As part of this, the hard-coded values that configure the size of the
array describing the topology of the power domain tree are increased
to max. 8 clusters, max. 8 cores per cluster & max 4 threads per core.
This ensures the port works with cluster configurations up to these
sizes. When there are too many entries for the number of available PEs,
e.g. if there is a variable number of CPUs between clusters, then there
will be empty entries in the array. This is permitted and the PSCI
library will still function as expected. While this increases its size,
this shouldn't be an issue in the context of the size of BL31, and is
worth the trade-off for the extra compatibility.
Signed-off-by: Oliver Swede <oli.swede@arm.com>
Change-Id: I7d4ae1e20b2e99fdbac428d122a2cf9445394363
This initializes the GIC using the Arm GIC drivers in TF-A.
The initial FPGA image uses a GIC600 implementation, and so that its
power controller is enabled, this platform port calls the corresponding
implementation-specific routines.
Signed-off-by: Oliver Swede <oli.swede@arm.com>
Change-Id: I88d5a073eead4b653b1ca73273182cd98a95e4c5
This sets the frequency of the system counter so that the Delay Timer
driver programs the correct value to CNTCRL. This value depends on
the FPGA image being used, and is 10MHz for the initial test image.
Once configured, the BL31 platform setup sequence then enables the
system counter.
Signed-off-by: Oliver Swede <oli.swede@arm.com>
Change-Id: Ieb036a36fd990f350b5953357424a255b8ac5d5a
This adds a basic PSCI implementation allow secondary CPUs to be
released from an initial state and continue through to the warm boot
entrypoint.
Each secondary CPU is kept in a holding pen, whereby it polls the value
representing its hold state, by reading this from an array that acts as
a table for all the PEs. The hold states are initially set to 0 for all
cores to indicate that the executing core should continue polling.
To prevent the secondary CPUs from interfering with the platform's
initialization, they are only updated by the primary CPU once the cold
boot sequence has completed and fpga_pwr_domain_on(mpidr) is called.
The polling target CPU will then read 1 (which indicates that it should
branch to the warm reset entrypoint) and then jump to that address
rather than continue polling.
In addition to the initial polling behaviour of the secondary CPUs
before their warm boot reset sequence, they are also placed in a
low-power wfe() state at the end of each poll; accordingly, the PSCI
fpga_pwr_domain_on(mpidr) function also signals an event to all cores
(after updating the target CPU's hold entry) to wake them from this
state, allowing any secondary CPUs that are still polling to check
their hold state again.
This method is in accordance with both the PSCI and Linux kernel
recommendations, as the lessened overhead reduces the energy
consumption associated with the busy-loop.
The table of hold entries is implemented by a global array as shared SRAM
(which is used by other platforms in similar implementations) is not
available on the FPGA images.
Signed-off-by: Oliver Swede <oli.swede@arm.com>
Change-Id: I65cfd1892f8be1dfcb285f0e1e94e7a9870cdf5a
This makes use of the PRELOADED_BL33_BASE flag to indicate to BL31 that
the BL33 payload (kernel) has already been loaded and resides in memory;
BL31 will then jump to the non-secure address.
For this port the BL33 payload is the Linux kernel, and in accordance
with the pre-kernel setup requirements (as specified in the `Booting
AArch64 Linux' documentation:
https://www.kernel.org/doc/Documentation/arm64/booting.txt),
this change also sets up the primary CPU's registers x0-x3 so they are
the expected values, which includes the address of the DTB at x0.
An external linker script is currently required to combine BL31, the
BL33 payload, and any other software images to create an ELF file that
can be uploaded to the FPGA board along with the bit file. It therefore
has dependencies on the value of PRELOADED_BL33_BASE (kernel base) and
the DTB base (plus any other relevant base addresses used to
distinguish the different ELF sections), both of which are set in this
patch.
Signed-off-by: Oliver Swede <oli.swede@arm.com>
Change-Id: If7ae8ee82d1e09fb05f553f6077ae13680dbf66b
This adds the minimal functions and definitions to create a basic
BL31 port for an initial FPGA image, in order for the port to be
uploaded to one the FPGA boards operated by an internal group within
Arm, such that BL31 runs as a payload for an image.
Future changes will enable the port for a wide range of system
configurations running on the FPGA boards to ensure compatibility with
multiple FPGA images.
It is expected that this will replace the FPGA fork of the Linux kernel
bootwrapper by performing similar secure-world initialization and setup
through the use of drivers and other well-established methods, before
passing control to the kernel, which will act as the BL33 payload and
run in EL2NS.
This change introduces a basic, loadable port with the console
initialized by setting the baud rate and base address of the UART as
configured by the Zeus image.
It is a BL31-only port, and RESET_TO_BL31 is enabled to reflect this.
Signed-off-by: Oliver Swede <oli.swede@arm.com>
Change-Id: I1817ad81be00afddcdbbda1ab70eb697203178e2
This patch provides support for measured boot by adding calculation
of BL2 image hash in BL1 and writing these data in TB_FW_CONFIG DTB.
Change-Id: Ic074a7ed19b14956719c271c805b35d147b7cec1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
When SPD=spmd and SPMD_SPM_AT_SEL2=0, that is SPMC sits at S-EL1
then there is no need for TF-A to load secure partitions individually.
In this configuration, SPMC handles secure partition loading at
S-EL1/EL0 levels.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I06a0d88a4811274a8c347ce57b56bb5f64e345df
To demonstrate communication between SP's two instances of Cactus at
S-EL1 has been used.
This patch replaces Ivy SP with cactus-secondary SP which aligns with
changes in tf-a-tests repository.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Iee84f1f7f023b7c4f23fbc13682a42614a7f3707
When using the SPM Dispatcher, the SPMC sits as a BL32 component
(BL32_IMAGE_ID). The SPMC manifest is passed as the TOS fw config
component (TOS_FW_CONFIG_ID). It defines platform specific attributes
(memory range and physical CPU layout) as well as the attributes for
each secure partition (mostly load address). This manifest is passed
to the SPMC on boot up. An SP package contains the SP dtb in the SPCI
defined partition manifest format. As the SPMC manifest was enriched
it needs an increase of tos_fw-config max-size in fvp_fw_config dts.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Ia1dce00c6c4cbaa118fa56617980d32e2956a94e
Rather than creating entry in plat_arm_mmap array to map the
entire DRAM region in BL31/SP_MIN, only map a smaller region holding
HW_CONFIG DTB. Consequently, an increase in number of sub-translation
tables(level-2 and level-3) i.e., MAX_XLAT_TABLES is necessary to map
the new region in memory.
In order to accommodate the increased code size in BL31 i.e.,
PROGBITS, the max size of BL31 image is increased by 0x1000(4K).
Change-Id: I540b8ee550588e22a3a9fb218183d2ab8061c851
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Implemented SMCCC_ARCH_SOC_ID call in order to get below
SOC information:
1. SOC revision
2. SOC version
Implementation done using below SMCCC specification document:
https://developer.arm.com/docs/den0028/c
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ie0595f1c345a6429a6fb4a7f05534a0ca9c9a48b
Merge the previously introduced arm_fconf_io_storage into arm_io_storage. This
removes the duplicate io_policies and functions definition.
This patch:
- replace arm_io_storage.c with the content of arm_fconf_io_storage.c
- rename the USE_FCONF_BASED_IO option into ARM_IO_IN_DTB.
- use the ARM_IO_IN_DTB option to compile out io_policies moved in dtb.
- propagate DEFINES when parsing dts.
- use ARM_IO_IN_DTB to include or not uuid nodes in fw_config dtb.
- set the ARM_IO_IN_DTB to 0 by default for fvp. This ensure that the behavior
of fvp stays the same as it was before the introduction of fconf.
Change-Id: Ia774a96d1d3a2bccad29f7ce2e2b4c21b26c080e
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
This patch introduces the `SPCI_ID_GET` interface which will return the
ID of the calling SPCI component. Returns 0 for requests from the
non-secure world and the SPCI component ID as specified in the manifest
for secure world requests.
Change-Id: Icf81eb1d0e1d7d5c521571e04972b6e2d356e0d1
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Signed-off-by: Marc Bonnici <marc.bonnici@arm.com>
To accommodate the increasing size of the SCP_BL2 binary, the base
address of the memory region allocated to SCP_BL2 has been moved
downwards from its current (mostly) arbitrary address to the beginning
of the non-shared trusted SRAM.
Change-Id: I086a3765bf3ea88f45525223d765dc0dbad6b434
Signed-off-by: Chris Kay <chris.kay@arm.com>
Add CLCD, HDLCD, PCI and VIRTIO devices as source interfaces for TZC
filter unit to enable DMA for these devices.
Change-Id: Ifad2e56b18605311936e03cfcccda573cac7e60a
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
The motivation behind this patch and following patches is to extract
information about the platform in runtime rather than depending on
compile time macros such as FVP_CLUSTER_COUNT. This partially enables
us to use a single binary for a family of platforms which all have
similar hardware capabilities but differ in configurations.
we populate the data structure describing the power domain hierarchy
of the platform dynamically by querying the number of clusters and cpus
using fconf getter APIs. Compile time macro such as FVP_CLUSTER_COUNT
is still needed as it determines the size of related data structures.
Note that the cpu-map node in HW_CONFIG dts represents a logical
hierarchy of power domains of CPU. However, in reality, the power
domains may not have been physically built in such hierarchy.
Change-Id: Ibcbb5ca7b2c969f8ad03ab2eab289725245af7a9
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Create, register( and implicitly invoke) fconf_populate_topology()
function which extracts the topology related properties from dtb into
the newly created fconf based configuration structure 'soc_topology'.
Appropriate libfdt APIs are added to jmptbl.i file for use with USE_ROMLIB
build feature.
A new property which describes the power domain levels is added to the
HW_CONFIG device tree source files.
This patch also fixes a minor bug in the common device tree file
fvp-base-gicv3-psci-dynamiq-common.dtsi
As this file includes fvp-base-gicv3-psci-common.dtsi, it is necessary
to delete all previous cluster node definitons because DynamIQ based
models have upto 8 CPUs in each cluster. If not deleted, the final dts
would have an inaccurate description of SoC topology, i.e., cluster0
with 8 or more core nodes and cluster1 with 4 core nodes.
Change-Id: I9eb406da3ba4732008a66c01afec7c9fa8ef59bf
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Necessary infrastructure added to integrate fconf framework in BL31 & SP_MIN.
Created few populator() functions which parse HW_CONFIG device tree
and registered them with fconf framework. Many of the changes are
only applicable for fvp platform.
This patch:
1. Adds necessary symbols and sections in BL31, SP_MIN linker script
2. Adds necessary memory map entry for translation in BL31, SP_MIN
3. Creates an abstraction layer for hardware configuration based on
fconf framework
4. Adds necessary changes to build flow (makefiles)
5. Minimal callback to read hw_config dtb for capturing properties
related to GIC(interrupt-controller node)
6. updates the fconf documentation
Change-Id: Ib6292071f674ef093962b9e8ba0d322b7bf919af
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
A populate() function essentially captures the value of a property,
defined by a platform, into a fconf related c structure. Such a
callback is usually platform specific and is associated to a specific
configuration source.
For example, a populate() function which captures the hardware topology
of the platform can only parse HW_CONFIG DTB. Hence each populator
function must be registered with a specific 'config_type' identifier.
It broadly represents a logical grouping of configuration properties
which is usually a device tree source file.
Example:
> TB_FW: properties related to trusted firmware such as IO policies,
base address of other DTBs, mbedtls heap info etc.
> HW_CONFIG: properties related to hardware configuration of the SoC
such as topology, GIC controller, PSCI hooks, CPU ID etc.
This patch modifies FCONF_REGISTER_POPULATOR macro and fconf_populate()
to register and invoke the appropriate callbacks selectively based on
configuration type.
Change-Id: I6f63b1fd7a8729c6c9137d5b63270af1857bb44a
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Shared RAM region in the remote chip's memory is used as one of the
mailbox region (SCMI payload area) through which the AP core on the
local chip and SCP core on the remote chip exchange SCMI protocol
message during the initialization. Mark this region as non-cacheable in
the MMAP entry to prevent local AP core from reading stale data from the
cache.
Change-Id: I7e9dc5fbcc3b40e9bcff5499f15abd2aadaed385
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Since N1SDP has a system level cache which is an
external LLC enable the NEOVERSE_N1_EXTERNAL_LLC flag.
Change-Id: Idb34274e61e7fd9db5485862a0caa497f3e290c7
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
* changes:
plat/arm: Pass cookie argument down to arm_get_rotpk_info()
plat/arm: Add support for dualroot CoT
plat/arm: Provide some PROTK files for development
This patch provides separation of GICD, GICR accessor
functions and adds new macros for GICv3 registers access
as a preparation for GICv3.1 and GICv4 support.
NOTE: Platforms need to modify to include both
'gicdv3_helpers.c' and 'gicrv3_helpers.c' instead of the
single helper file previously.
Change-Id: I1641bd6d217d6eb7d1228be3c4177b2d556da60a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch implements loading of Secure Partition packages using
existing framework of loading other bl images.
The current framework uses a statically defined array to store all the
possible image types and at run time generates a link list and traverse
through it to load different images.
To load SPs, a new array of fixed size is introduced which will be
dynamically populated based on number of SPs available in the system
and it will be appended to the loadable images list.
Change-Id: I8309f63595f2a71b28a73b922d20ccba9c4f6ae4
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Added SPMD_SPM_AT_SEL2 build command line parameter.
Set to 1 to run SPM at S-EL2.
Set to 0 to run SPM at S-EL1 (pre-v8.4 or S-EL2 is disabled).
Removed runtime EL from SPM core manifest.
Change-Id: Icb4f5ea4c800f266880db1d410d63fe27a1171c0
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Add load address and UUID in fw config dts for Cactus and Ivy which are
example SP's in tf-test repository.
For prototype purpose these information is added manually but later on
it will be updated at compile time from SP layout file and SP manifests
provided by platform.
Change-Id: I41f485e0245d882c7b514bad41fae34036597ce4
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Use the firmware configuration framework to retrieve information about
Secure Partitions to facilitate loading them into memory.
To load a SP image we need UUID look-up into FIP and the load address
where it needs to be loaded in memory.
This patch introduces a SP populator function which gets UUID and load
address from firmware config device tree and updates its C data
structure.
Change-Id: I17faec41803df9a76712dcc8b67cadb1c9daf8cd
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
* changes:
board/rddaniel: intialize tzc400 controllers
plat/arm/tzc: add support to configure multiple tzc400
plat/arm: allow boards to specify second DRAM Base address
plat/arm: allow boards to define PLAT_ARM_TZC_FILTERS
MISRA C-2012 Rule 20.7:
Macro parameter expands into an expression without being wrapped by parentheses.
MISRA C-2012 Rule 12.1:
Missing explicit parentheses on sub-expression.
MISRA C-2012 Rule 18.4:
Essential type of the left hand operand is not the same as that of the right
operand.
Include does not provide any needed symbols.
Change-Id: Ie1c6451cfbc8f519146c28b2cf15c50b1f36adc8
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
This patch fixes incorrect setting for DEVICE1_SIZE
for FVP platforms with more than 8 PEs.
The current value of 0x200000 supports only 8 PEs
and causes exception for FVP platforms with the greater
number of PEs, e.g. FVP_Base_Cortex_A65AEx8 with 16 PEs
in one cluster.
Change-Id: Ie6391509fe6eeafb8ba779303636cd762e7d21b2
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I7a23327394d142af4b293ea7ccd90b843c54587c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch introduces a build flag which allows the xlat tables
to be mapped in a read-only region within BL31 memory. It makes it
much harder for someone who has acquired the ability to write to
arbitrary secure memory addresses to gain control of the
translation tables.
The memory attributes of the descriptors describing the tables
themselves are changed to read-only secure data. This change
happens at the end of BL31 runtime setup. Until this point, the
tables have read-write permissions. This gives a window of
opportunity for changes to be made to the tables with the MMU on
(e.g. reclaiming init code). No changes can be made to the tables
with the MMU turned on from this point onwards. This change is also
enabled for sp_min and tspd.
To make all this possible, the base table was moved to .rodata. The
penalty we pay is that now .rodata must be aligned to the size of
the base table (512B alignment). Still, this is better than putting
the base table with the higher level tables in the xlat_table
section, as that would cost us a full 4KB page.
Changing the tables from read-write to read-only cannot be done with
the MMU on, as the break-before-make sequence would invalidate the
descriptor which resolves the level 3 page table where that very
descriptor is located. This would make the translation required for
writing the changes impossible, generating an MMU fault.
The caches are also flushed.
Signed-off-by: Petre-Ionut Tudor <petre-ionut.tudor@arm.com>
Change-Id: Ibe5de307e6dc94c67d6186139ac3973516430466
The dualroot chain of trust involves 2 root-of-trust public keys:
- The classic ROTPK.
- The platform ROTPK (a.k.a. PROTPK).
Use the cookie argument as a key ID for plat_get_rotpk_info() to return the
appropriate one. This only applies if we are using the dualroot CoT ; if using
the TBBR one, the behaviour is unchanged.
Change-Id: I400707a87ec01afd5922b68db31d652d787f79bd
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The cookie will be leveraged in the next commit.
Change-Id: Ie8bad275d856d84c27466461cf815529dd860446
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
- Use the development PROTPK if using the dualroot CoT.
Note that unlike the ROTPK, the PROTPK key hash file is not generated
from the key file, instead it has to be provided. This might be
enhanced in the future.
- Define a CoT build flag for the platform code to provide different
implementations where needed.
Change-Id: Iaaf25183b94e77a99a5d8d875831d90c102a97ea
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
When using the new dualroot chain of trust, a new root of trust key is
needed to authenticate the images belonging to the platform owner.
Provide a development one to deploy this on Arm platforms.
Change-Id: I481145e09aa564822d474cb47d38ec211dd24efd
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
A TZC400 controller is placed inline on DRAM channels and regulates
the secure and non-secure accesses to both secure and non-secure
regions of the DRAM memory. Configure each of the TZC controllers
accordingly.
Change-Id: I75f6d13591a7fe9e50ce15c793e35a8018041815
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
For platforms that have two or more TZC400 controllers instantiated,
allow the TZC400 driver to be usable with all those instances.
This is achieved by allowing 'arm_tzc400_setup' function to accept
the base address of the TZC400 controller.
Change-Id: I4add470e6ddb58432cd066145e644112400ab924
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
The base address for second DRAM varies across different platforms.
So allow platforms to define second DRAM by moving Juno/SGM-775 specific
definition of second DRAM base address to Juno/SGM-775 board definition
respectively, SGI/RD specific definition of DRAM 2 base address to SGI
board definition.
Change-Id: I0ecd3a2bd600b6c7019c7f06f8c452952bd07cae
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
A TZC400 can have upto 4 filters and the number of filters instantiated
within a TZC400 is platform dependent. So allow platforms to define the
value of PLAT_ARM_TZC_FILTERS by moving the existing Juno specific
definition of PLAT_ARM_TZC_FILTERS to Juno board definitions.
Change-Id: I67a63d7336595bbfdce3163f9a9473e15e266f40
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
Use CREATE_SEQ helper macro to create sequence of valid chip counts
instead of manually creating the sequence. This allows a scalable
approach to increase the valid chip count sequence in the future.
Change-Id: I5ca7a00460325c156b9e9e52b2bf656a2e43f82d
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
When TF-A is built with RESET_TO_BL31=1 option, BL31 is the
first image to be run and should have all the memory allocated
to it except for the memory reserved for Shared RAM at the start
of Trusted SRAM.
This patch fixes FVP BL31 load address and its image size for
RESET_TO_BL31=1 option. BL31 startup address should be set to
0x400_1000 and its maximum image size to the size of Trusted SRAM
minus the first 4KB of shared memory.
Loading BL31 at 0x0402_0000 as it is currently stated in
'\docs\plat\arm\fvp\index.rst' causes EL3 exception when the
image size gets increased (i.e. building with LOG_LEVEL=50)
but doesn't exceed 0x3B000 not causing build error.
Change-Id: Ie450baaf247f1577112f8d143b24e76c39d33e91
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Adding support for 32MHz UART clock and selecting it as the
default UART clock
Change-Id: I9541eaff70424e85a3b5ee4820ca0e7efb040d2c
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Running checkpatch.pl on the codebase and making required changes
Change-Id: I7d3f8764cef632ab2a6d3c355c68f590440b85b8
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Note: This patch implements in-band messaging protocol only.
ARM has launched a next version of MHU i.e. MHUv2 with its latest
subsystems. The main change is that the MHUv2 is now a distributed IP
with different peripheral views (registers) for the sender and receiver.
Another main difference is that MHUv1 duplex channels are now split into
simplex/half duplex in MHUv2. MHUv2 has a configurable number of
communication channels. There is a capability register (MSG_NO_CAP) to
find out how many channels are available in a system.
The register offsets have also changed for STAT, SET & CLEAR registers
from 0x0, 0x8 & 0x10 in MHUv1 to 0x0, 0xC & 0x8 in MHUv2 respectively.
0x0 0x4 0x8 0xC 0x1F
------------------------....-----
| STAT | | | SET | | |
------------------------....-----
Transmit Channel
0x0 0x4 0x8 0xC 0x1F
------------------------....-----
| STAT | | CLR | | | |
------------------------....-----
Receive Channel
The MHU controller can request the receiver to wake-up and once the
request is removed, the receiver may go back to sleep, but the MHU
itself does not actively put a receiver to sleep.
So, in order to wake-up the receiver when the sender wants to send data,
the sender has to set ACCESS_REQUEST register first in order to wake-up
receiver, state of which can be detected using ACCESS_READY register.
ACCESS_REQUEST has an offset of 0xF88 & ACCESS_READY has an offset
of 0xF8C and are accessible only on any sender channel.
This patch adds necessary changes in a new file required to support the
latest MHUv2 controller. This patch also needs an update in DT binding
for ARM MHUv2 as we need a second register base (tx base) which would
be used as the send channel base.
Change-Id: I1455e08b3d88671a191c558790c503eabe07a8e6
Signed-off-by: Tushar Khandelwal <tushar.khandelwal@arm.com>
Adding support for generating a semi-random number required for
enabling building TF-A with stack protector support.
TF-A for corstone-700 may now be built using ENABLE_STACK_PROTECTOR=all
Change-Id: I03e1be1a8d4e4a822cf286f3b9ad4da4337ca765
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Forced hash generation used to always generate hash via RSA encryption.
This patch changes encryption based on ARM_ROTPK_LOCATION.
Also removes setting KEY_ALG based on ARM_ROTPL_LOCATION - there is no
relation between these two.
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: Id727d2ed06176a243719fd0adfa0cae26c325005
* changes:
SPMD: enable SPM dispatcher support
SPMD: hook SPMD into standard services framework
SPMD: add SPM dispatcher based upon SPCI Beta 0 spec
SPMD: add support to run BL32 in TDRAM and BL31 in secure DRAM on Arm FVP
SPMD: add support for an example SPM core manifest
SPMD: add SPCI Beta 0 specification header file
This patch adds support to the build system to include support for the SPM
dispatcher when the SPD configuration option is spmd.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: Ic1ae50ecd7403fcbcf1d318abdbd6ebdc642f732
This patch reserves and maps the Trusted DRAM for SPM core execution.
It also configures the TrustZone address space controller to run BL31
in secure DRAM.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I7e1bb3bbc61a0fec6a9cb595964ff553620c21dc
This patch repurposes the TOS FW configuration file as the manifest for
the SPM core component which will reside at the secure EL adjacent to
EL3. The SPM dispatcher component will use the manifest to determine how
the core component must be initialised. Routines and data structure to
parse the manifest have also been added.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: Id94f8ece43b4e05609f0a1d364708a912f6203cb
In preparation for adding support for Reference Design platforms
which have different base addresses for GIC Distributor or
Redistributor, move GIC related base addresses to individual platform
definition files.
Change-Id: Iecf52b4392a30b86905e1cd047c0ff87d59d0191
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Include multi-chip-mode parameter in HW_CONFIG dts to let next stage of
boot firmware know about the multi-chip operation mode.
Change-Id: Ic7535c2280fd57180ad14aa0ae277cf0c4d1337b
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
RD-N1-Edge based platforms can operate in dual-chip configuration
wherein two rdn1edge SoCs are connected through a high speed coherent
CCIX link.
This patch adds a function to check if the RD-N1-Edge platform is
operating in multi-chip mode by reading the SID register's NODE_ID
value. If operating in multi-chip mode, initialize GIC-600 multi-chip
operation by overriding the default GICR frames with array of GICR
frames and setting the chip 0 as routing table owner.
The address space of the second RD-N1-Edge chip (chip 1) starts from the
address 4TB. So increase the physical and virtual address space size to
43 bits to accommodate the multi-chip configuration. If the multi-chip
mode configuration is detected, dynamically add mmap entry for the
peripherals memory region of the second RD-N1-Edge SoC. This is required
to let the BL31 platform setup stage to configure the devices in the
second chip.
PLATFORM_CORE_COUNT macro is set to be multiple of CSS_SGI_CHIP_COUNT
and topology changes are added to represent the dual-chip configuration.
In order the build the dual-chip platform, CSS_SGI_CHIP_COUNT macro
should be set to 2:
export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all
Change-Id: I576cdaf71f0b0e41b9a9181fa4feb7091f8c7bb4
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.
Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.
Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
AFF3 bits of MPIDR corresponds to Chip-Id in Arm multi-chip platforms.
For calculating linear core position of CPU cores from slave chips, AFF3
bits has to be used. Update `plat_arm_calc_core_pos` assembly function
to include AFF3 bits in calculation.
Change-Id: I4af2bd82ab8e31e18bc61de22705a73893954260
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Some of the Reference Design platforms like RD-N1-Edge can operate in
multi-chip configuration wherein two or more SoCs are connected through
a high speed coherent CCIX link. For the RD platforms, the remote chip
address space is at the offset of 4TB per chip. In order for the primary
chip to access the device memory region on the remote chip, the required
memory region entries need to be added as mmap entry. This patch adds
macros related to the remote chip device memory region.
Change-Id: I833810b96f1a0e7c3c289ac32597b6ba03344c80
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Multi-chip platforms have two or more identical chips connected using a
high speed coherent link. In order to identify such platforms,
add chip_id and multi_chip_mode information in the platform variant
info structure. The values of these two new elements is populated
during boot.
Change-Id: Ie6e89cb33b3f0f408814f6239cd06647053e23ed
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
For SGI-575 and RD platforms, move bl31_platform_setup handler to
individual board files to allow the platforms to perform board specific
bl31 setup.
Change-Id: Ia44bccc0a7f40a155b33909bcb438a0909b20d42
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
RD-E1-Edge platform consists of two clusters with eight CPUs each and
two processing elements (PE) per CPU. Commit a9fbf13e04 (plat/arm/sgi:
move topology information to board folder) defined the RD-E1-Edge
topology tree to have two clusters with eight CPUs each but PE per CPU
entries were not added. This patch fixes the topology tree accordingly.
Change-Id: I7f97f0013be60e5d51c214fce3962e246bae8a0b
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Introduce macro 'CSS_SGI_CHIP_COUNT' to allow Arm CSS platforms with
multi-chip support to define number of chiplets on the platform. By
default, this flag is set to 1 and does not affect the existing single
chip platforms.
For multi-chip platforms, override the default value of
CSS_SGI_CHIP_COUNT with the number of chiplets supported on the
platform. As an example, the command below sets the number of chiplets
to two on the RD-N1-Edge multi-chip platform:
export CROSS_COMPILE=<path-to-cross-compiler>
make PLAT=rdn1edge CSS_SGI_CHIP_COUNT=2 ARCH=aarch64 all
Change-Id: If364dc36bd34b30cc356f74b3e97633933e6c8ee
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Currently, an IO setup failure will be ignored on arm platform release
build. Change this to panic instead.
Change-Id: I027a045bce2422b0a0fc4ff9e9d4c6e7bf5d2f98
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change the return type of "arm_io_is_toc_valid()" and
"plat_arm_bl1_fwu_needed()" to bool, to match function behavior.
Change-Id: I503fba211219a241cb263149ef36ca14e3362a1c
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Use the firmware configuration framework to store the io_policies
information inside the configuration device tree instead of the static
structure in the code base.
The io_policies required by BL1 can't be inside the dtb, as this one is
loaded by BL1, and only available at BL2.
This change currently only applies to FVP platform.
Change-Id: Ic9c1ac3931a4a136aa36f7f58f66d3764c1bfca1
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Use the firmware configuration framework in arm dynamic configuration
to retrieve mbedtls heap information between bl1 and bl2.
For this, a new fconf getter is added to expose the device tree base
address and size.
Change-Id: Ifa5ac9366ae100e2cdd1f4c8e85fc591b170f4b6
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Use fconf to retrieve the `disable_authentication` property.
Move this access from arm dynamic configuration to bl common.
Change-Id: Ibf184a5c6245d04839222f5457cf5e651f252b86
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
This patch introduces a better separation between the trusted-boot
related properties, and the dynamic configuration DTBs loading
information.
The dynamic configuration DTBs properties are moved to a new node:
`dtb-registry`. All the sub-nodes present will be provided to the
dynamic config framework to be loaded. The node currently only contains
the already defined configuration DTBs, but can be extended for future
features if necessary.
The dynamic config framework is modified to use the abstraction provided
by the fconf framework, instead of directly accessing the DTBs.
The trusted-boot properties are kept under the "arm,tb_fw" compatible
string, but in a separate `tb_fw-config` node.
The `tb_fw-config` property of the `dtb-registry` node simply points
to the load address of `fw_config`, as the `tb_fw-config` is currently
part of the same DTB.
Change-Id: Iceb6c4c2cb92b692b6e28dbdc9fb060f1c46de82
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Use the dtb provided by bl1 as configuration file for fconf.
Change-Id: I3f466ad9b7047e1a361d94e71ac6d693e31496d9
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Move the loading of the dtb from arm_dym_cfg to fconf. The new loading
function is not associated to arm platform anymore, and can be moved
to bl_main if wanted.
Change-Id: I847d07eaba36d31d9d3ed9eba8e58666ea1ba563
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Introduce the Firmware CONfiguration Framework (fconf).
The fconf is an abstraction layer for platform specific data, allowing
a "property" to be queried and a value retrieved without the requesting
entity knowing what backing store is being used to hold the data.
The default backing store used is C structure. If another backing store
has to be used, the platform integrator needs to provide a "populate()"
function to fill the corresponding C structure.
The "populate()" function must be registered to the fconf framework with
the "FCONF_REGISTER_POPULATOR()". This ensures that the function would
be called inside the "fconf_populate()" function.
A two level macro is used as getter:
- the first macro takes 3 parameters and converts it to a function
call: FCONF_GET_PROPERTY(a,b,c) -> a__b_getter(c).
- the second level defines a__b_getter(c) to the matching C structure,
variable, array, function, etc..
Ex: Get a Chain of trust property:
1) FCONF_GET_PROPERY(tbbr, cot, BL2_id) -> tbbr__cot_getter(BL2_id)
2) tbbr__cot_getter(BL2_id) -> cot_desc_ptr[BL2_id]
Change-Id: Id394001353ed295bc680c3f543af0cf8da549469
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Enables usage of ARM_ROTPK_LOCATION=regs for FVP board.
Removes hard-coded developer keys. Instead, setting
ARM_ROTPK_LOCATION=devel_* takes keys from default directory.
In case of ROT_KEY specified - generates a new hash and replaces the
original.
Note: Juno board was tested by original feature author and was not tested
for this patch since we don't have access to the private key. Juno
implementation was moved to board-specific file without changing
functionality. It is not known whether byte-swapping is still needed
for this platform.
Change-Id: I0fdbaca0415cdcd78f3a388551c2e478c01ed986
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Stack usage reaches 90% with some configuration. Bump slightly the stack
size to prevent a stack-overflow.
Change-Id: I44ce8b12906586a42f152b7677785fcdc5e78ae1
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Fix code that violates the MISRA rule:
MISRA C-2012 Rule 11.9: Literal "0" shall not be used as
null pointer constant.
The fix explicitly checks whether a pointer is NULL.
Change-Id: Ibc318dc0f464982be9a34783f24ccd1d44800551
Signed-off-by: Zelalem <zelalem.aweke@arm.com>
This patch adds 'fdtw_read_bytes' and 'fdtw_write_inplace_bytes'
functions for read/write array of bytes from/to a given property.
It also adds 'fdt_setprop_inplace_namelen_partial' to jmptbl.i
files for builds with USE_ROMLIB=1 option.
Change-Id: Ied7b5c8b38a0e21d508aa7bcf5893e656028b14d
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Allows to select the chain of trust to use when the Trusted Boot feature
is enabled. This affects both the cert_create tool and the firmware
itself.
Right now, the only available CoT is TBBR.
Change-Id: I7ab54e66508a1416cb3fcd3dfb0f055696763b3d
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The Secure Configuration Register is 64-bits in AArch64 and 32-bits in
AArch32. Use u_register_t instead of unsigned int to reflect this.
Change-Id: I51b69467baba36bf0cfaec2595dc8837b1566934
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Manish V Badarkhe
Sandeep Tripathy
Sayanta Pattanayak
Olivier Deprez
Ruari Phipps
Mark Dykes
Madhukar Pappireddy
Manish Pandey
Jimmy Brisson
Alexei Fedorov
André Przywara
Javier Almansa Sobrino
Vijayenthiran Subramaniam
Sandrine Bailleux
Abdellatif El Khlifi
laurenw-arm
Louis Mayencourt
Usama Arif
J-Alves
Balint Dobszay
Aditya Angadi
Chris Kay
Masahiro Yamada
Oliver Swede
Max Shvetsov
Chandni Cherukuri
Petre-Ionut Tudor
joanna.farley
Suyash Pathak
Vishnu Banavath
Avinash Mehta
Khandelwal
Morten Borup Petersen
Achin Gupta
Zelalem