Move efuse definitions to a separate header file for later
usage with other FW modules.
Change-Id: I2e9465f760d0388c8e5863bc64a4cdc57de2417f
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/47313
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Yi Guo <yi.guo@cavium.com>
The SCMI power domain protocol in firmware has been updated to v2.0,
thus update the corresponding version in TF-A too.
Signed-off-by: Nicola Mazzucato <nicola.mazzucato@arm.com>
Change-Id: If3920ff71136dce94b2780e29a47f24aa09876c0
Enable basic support for QEMU "max" CPU.
The "max" CPU does not attampt to emulate any specific CPU, but rather
just enables all the functions emulated by QEMU.
Change-Id: I69c212932ef61433509662d0fefbabb1e9e71cf2
Signed-off-by: Leif Lindholm <leif@nuviainc.com>
Since there is a secure and non-secure version of the timer registers
there is no need to preserve their context in EL3.
With that, following registers were removed from EL3 save/restore
routine:
cnthps_ctl_el2
cnthps_tval_el2
cnthps_cval_el2
cnthvs_ctl_el2
cnthvs_tval_el2
cnthvs_cval_el2
cnthp_ctl_el2
cnthp_cval_el2
cnthp_tval_el2
cnthv_ctl_el2
cnthv_cval_el2
cnthv_tval_el2
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: I6e2fc09c74a7375c4fccc11f12af4e39e6dc616b
The legacy console is gone. Re-add DCC console support based
on the multi-console framework.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Ia8388721093bc1be3af40974530d7c9a9ae5f43e
Broadcom I2C controller driver. Follwoing API's are supported:-
- i2c_init() Intialize ethe I2C controller
- i2c_probe()
- i2c_set_bus_speed() Set the I2C bus speed
- i2c_get_bus_speed() Get the current bus speed
- i2c_recv_byte() Receive one byte of data.
- i2c_send_byte() Send one byteof data
- i2c_read_byte() Read single byte of data
- i2c_read() Read multiple bytes of data
- i2c_write_byte Write single byte of data
- i2c_write() Write multiple bytes of data
This driver is verified by reading the DDR SPD data.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Change-Id: I2d7fe53950e8b12fab19d0293020523ff8b74e13
NXP SMMU driver API for NXP SoC.
- Currently it supports by-passing SMMU, called only when NXP CAAM
is enabled.
- (TBD) AMQ based SMMU access control: Access Management Qualifiers (AMQ)
advertised by a bus master for a given transaction.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I23a12928ddedb1a2cf4b396606e35c67e016e331
Flexspi driver now introduces read/write/erase APIs for complete flash
size, FAST-READ are by default used and IP bus is used for erase, read
and write using flexspi APIs.
Framework layer is currently embedded in driver itself using flash_info
defines.
Test cases are also added to confirm flash functionality currently under
DEBUG flag.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Change-Id: I755c0f763f6297a35cad6885f84640de50f51bb0
NXP Timer Apis are based on:
- drivers/delay_timer
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I2cbccf4c082a10affee1143390905b9cc99c3382
Generic framework is added to include platform defined UUID.
This framework is added for the following:
- All NXP SoC based platforms needed additional fip-fuse.bin
- NXP SoC lx2160a based platforms requires additional fip-ddr.bin
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Ibe05d9c596256e34077287a490dfcd5b731ef2cf
Conditional definition for the macro MAX_NUMBER_IDS.
This will allow to update this definition by the platform
specific implementation.
Since, NXP SoC lx2160a based platforms requires additional
FIP DDR to be loaded before initializing the DDR.
It requires addition of defines for DDR image IDs.
A dedicated header plat_tbbr_img_def.h is added to the platform
folder - plat/nxp/common/include/default/
Inclusion of this header file will depend on the compile time
flag PLAT_TBBR_IMG_DEF.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I4faba74dce578e2a34acbc8915ff75d7b8368cee
Incorrect value is picked for TF_MBEDTLS_USE_RSA defination,
even if the TF_MBEDTLS_RSA is enabled.
Due to which PK_DER_LEN is defined incorrectly.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I2ca4ca121e0287b88ea689c885ddcd45a34a3e91
Changes to 'tools/cert_create' folder, to include platform defined
certificates, keys, and extensions.
NXP SoC lx2160a : based platforms requires additional
FIP DDR to be loaded before initializing the DDR.
To enable chain of trust on these platforms, FIP DDR
image needs to be authenticated, additionally.
Platform specific folder 'tools/nxp/cert_create_helper'
is added to support platform specific macros and definitions.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I4752a30a9ff3aa1d403e9babe3a07ba0e6b2bf8f
A new function tzc400_it_handler() is created to manage TZC400
interrupts. The required helpers to read and clear interrupts are added
as well.
In case DEBUG is enabled, more information about the faulty access
(address, NSAID, type of access) is displayed.
Change-Id: Ie9ab1c199a8f12b2c9472d7120efbdf35711284a
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The UEFI specification details the represenatation
for the EFI_GUID type. Add this representation to the
uuid_helper_t union type so that GUID definitions
can be shared verbatim between UEFI and TF-A header
files.
Change-Id: Ie44ac141f70dd0025e186581d26dce1c1c29fce6
Signed-off-by: Tomas Pilar <tomas@nuviainc.com>
The speculation barrier feature (`FEAT_SB`) was introduced with and
made mandatory in the Armv8.5-A extension. It was retroactively made
optional in prior extensions, but the checks in our code-base do not
reflect that, assuming that it is only available in Armv8.5-A or later.
This change introduces the `ENABLE_FEAT_SB` definition, which derives
support for the `sb` instruction in the assembler from the feature
flags passed to it. Note that we assume that if this feature is enabled
then all the cores in the system support it - enabling speculation
barriers for only a subset of the cores is unsupported.
Signed-off-by: Chris Kay <chris.kay@arm.com>
Change-Id: I978ed38829385b221b10ba56d49b78f4756e20ea
Remove the former impdef SPMD service for SPMC entry point
registration. Replace with FFA_SECONDARY_EP_REGISTER ABI
providing a single entry point address into the SPMC for
primary and secondary cold boot.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I067adeec25fc12cdae90c15a616903b4ac4d4d83
ARMv8.6 adds virtual offset registers to support virtualization of the
event counters in EL1 and EL0. This patch enables support for this
feature in EL3 firmware.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I7ee1f3d9f554930bf5ef6f3d492e932e6d95b217
* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mapping at BLE stage
plat/marvell/armada/common/mss: use MSS SRAM in secure mode
include/drivers/marvell/mochi: add detection of secure mode
plat/marvell: fix SPD handling in dram port
marvell: drivers: move XOR0/1 DIOB from WIN 0 to 1
drivers/marvell/mochi: add support for cn913x in PCIe EP mode
drivers/marvell/mochi: add missing stream IDs configurations
plat/marvell/armada/a8k: support HW RNG by SMC
drivers/rambus: add TRNG-IP-76 driver
The Juno Trusted Entropy Source has a bias, which makes the generated
raw numbers fail a FIPS 140-2 statistic test.
To improve the quality of the numbers, we can use the CPU's CRC
instructions, which do a decent job on conditioning the bits.
This adds a *very* simple version of arm_acle.h, which is typically
provided by the compiler, and contains the CRC instrinsics definitions
we need. We need the original version by using -nostdinc.
Change-Id: I83d3e6902d6a1164aacd5060ac13a38f0057bd1a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add Rambus (InsideSecure) TRNG-IP-76 HW RNG driver.
This IP is part of Marvell Armada CP110/CP115 die integrated
to Armada 7k/8K/CN913x SoCs
Change-Id: I9c5f510ad6728c7ed168da43d85b19d5852cd873
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
The filters parameter passed to tzc400_configure_region() is supposed
to be filter bit flag without bit shift, so the macros
TZC_400_REGION_ATTR_FILTER_BIT and TZC_400_REGION_ATTR_FILTER_BIT_ALL
should always construct the value without any shift.
It is not a functional issue for TZC_REGION_ATTR_F_EN_SHIFT is lucky
to be 0.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I5d363c462b8517256523f637e670eefa56722afd
This adds the TRNG Firmware Interface Service to the standard
service dispatcher. This includes a method for dispatching entropy
requests to platforms and includes an entropy pool implementation to
avoid dropping any entropy requested from the platform.
Change-Id: I71cadb3cb377a507652eca9e0d68714c973026e9
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In DDR controller PWRTMG register, the mask for field SELFREF_TO_X32 is
wrong. This field is from bit 16 to 23.
Change-Id: Id336fb08c88f0a153df186dd819e41af72febb88
Signed-off-by: Yann Gautier <yann.gautier@st.com>
From commit: 21571b1d140ae7bb44e94c0afba2ec61456b275b
The coding guidelines[1] in TF-A forbid the use of ato*() functions
in favour of strto*(). However, the TF-A libc does not provide an
implementation of strto*(), making this rule impossible to satisfy.
Also made small changes to fit into TF-A project. Added the source
files to the libc makefile
[1] https://trustedfirmware-a.readthedocs.io/en/latest/process/coding-guidelines.html#libc-functions-that-are-banned-or-to-be-used-with-caution
Change-Id: I2e94a0b227ec39f6f4530dc50bb477999d27730f
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
From commit: 21571b1d140ae7bb44e94c0afba2ec61456b275b
The coding guidelines[1] in TF-A forbid the use of ato*() functions
in favour of strto*(). However, the TF-A libc does not provide an
implementation of strto*(), making this rule impossible to satisfy.
Also made small changes to fit into TF-A project. Added the source
files to the libc makefile
[1] https://trustedfirmware-a.readthedocs.io/en/latest/process/coding-guidelines.html#libc-functions-that-are-banned-or-to-be-used-with-caution
Change-Id: I9cb581574d46de73c3d6917ebf78935fc5ac075a
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
From commit: 21571b1d140ae7bb44e94c0afba2ec61456b275b
The coding guidelines[1] in TF-A forbid the use of ato*() functions
in favour of strto*(). However, the TF-A libc does not provide an
implementation of strto*(), making this rule impossible to satisfy.
Also made small changes to fit into TF-A project. Added the source
files to the libc makefile
[1] https://trustedfirmware-a.readthedocs.io/en/latest/process/coding-guidelines.html#libc-functions-that-are-banned-or-to-be-used-with-caution
Change-Id: I8c3b92751d1ce226c966f7c81fedd83f0846865e
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
From commit: 21571b1d140ae7bb44e94c0afba2ec61456b275b
The coding guidelines[1] in TF-A forbid the use of ato*() functions
in favour of strto*(). However, the TF-A libc does not provide an
implementation of strto*(), making this rule impossible to satisfy.
Also made small changes to fit into TF-A project. Added the source
files to the libc makefile
[1] https://trustedfirmware-a.readthedocs.io/en/latest/process/coding-guidelines.html#libc-functions-that-are-banned-or-to-be-used-with-caution
Change-Id: Ica95bf5da722913834fe90bf3fe743aa34e01e80
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
For SoCs which do not implement RAS, use DSB as a barrier to
synchronize pending external aborts at the entry and exit of
exception handlers. This is needed to isolate the SErrors to
appropriate context.
However, this introduces an unintended side effect as discussed
in the https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/3440
A summary of the side effect and a quick workaround is provided as
part of this patch and summarized here:
The explicit DSB at the entry of various exception vectors in BL31
for handling exceptions from lower ELs can inadvertently trigger an
SError exception in EL3 due to pending asyncrhonouus aborts in lower
ELs. This will end up being handled by serror_sp_elx in EL3 which will
ultimately panic and die.
The way to workaround is to update a flag to indicate if the exception
truly came from EL3. This flag is allocated in the cpu_context
structure. This is not a bullet proof solution to the problem at hand
because we assume the instructions following "isb" that help to update
the flag (lines 100-102 & 139-141) execute without causing further
exceptions.
Change-Id: I4d345b07d746a727459435ddd6abb37fda24a9bf
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
This patch does not change code, it only updates comments and macro name
for 6th bit of Status Register. So TF-A binary stay same.
6th bit of the Status Register is named TX EMPTY and is set to 1 when both
Transmitter Holding Register (THR) or Transmitter Shift Register (TSR) are
empty. It is when all characters were already transmitted.
There is also TX FIFO EMPTY bit in the Status Register which is set to 1
only when THR is empty.
In both console_a3700_core_init() and console_a3700_core_flush() functions
we should wait until both THR and TSR are empty therefore we should check
6th bit of the Status Register.
So current code is correct, just had misleading macro names and comments.
This change fixes this "documentation" issue, fixes macro name for 6th bit
of the Status Register and also updates comments.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I19e4e7f53a90bcfb318e6dd1b1249b6cbf81c4d3
Implementation is simple, just check if there is a pending character in
RX FIFO via RXRDY bit of Status Register and if yes, read it from
UART_RX_REG register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I226b6e336f44f5d0ca8dcb68e49a68e8f2f49708
Add ISAR0 feature register read helper, location
of FEAT_RNG bits, feature support helper and the
rndr/rndrrs register read helpers.
Signed-off-by: Tomas Pilar <tomas@nuviainc.com>
Change-Id: I2a785a36f62a917548e55892ce92fa8b72fcb99d
Cortex A78 erratum 1951500 is a Cat B erratum that applies to revisions
r0p0, r1p0, and r1p1. The workaround is to insert a DMB ST before
acquire atomic instructions without release semantics. This workaround
works on revisions r1p0 and r1p1, in r0p0 there is no workaround.
SDEN can be found here:
https://documentation-service.arm.com/static/5fb66157ca04df4095c1cc2e
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I47610cee75af6a127ea65edc4d5cffc7e6a2d0a3
Cortex A78 erratum 1941498 is a Cat B erratum that applies to revisions
r0p0, r1p0, and r1p1. The workaround is to set bit 8 in the ECTLR_EL1
register, there is a small performance cost (<0.5%) for setting this bit.
SDEN can be found here:
https://documentation-service.arm.com/static/5fb66157ca04df4095c1cc2e
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I959cee8e3d46c1b84ff5e4409ce5945e459cc6a9
Write char if fifo is empty. If this is done like this all chars are
printed. Because origin code just put that chars to fifo and in case of
reset messages were missing.
Before this change chars are put to fifo and only check before adding if
fifo is full. The patch is changing this logic that it is adding char only
when fifo is empty to make sure that in case of reset (by another SW for
example) all chars are printed. Maybe one char can be missed but for IP
itself it is much easier to send just one char compare to full fifo.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Ic24c2c1252bce24be2aed68ee29477ca4a549e5f
* changes:
allwinner: Use RSB for the PMIC connection on H6
allwinner: Return the PMIC to I2C mode after use
allwinner: Always use a 3MHz RSB bus clock
Increase SP max size for latest OP-TEE build with debug and
stats enabled.
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Change-Id: I4593884e0deb39ada10009f6876d815136f8ee65
This gives the rich OS the flexibility to choose between I2C and RSB
communication. Since a runtime address can only be assigned once after
entering RSB mode, it also lets the rich OS choose any runtime address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Id49c124c5e925985fc31c0ba38c7fb6c941aafa8
If FEAT_PMUv3 is implemented and PMEVTYPER<n>(_EL0).MT bit is implemented
as well, it is possible to control whether PMU counters take into account
events happening on other threads.
If FEAT_MTPMU is implemented, EL3 (or EL2) can override the MT bit
leaving it to effective state of 0 regardless of any write to it.
This patch introduces the DISABLE_MTPMU flag, which allows to diable
multithread event count from EL3 (or EL2). The flag is disabled
by default so the behavior is consistent with those architectures
that do not implement FEAT_MTPMU.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: Iee3a8470ae8ba13316af1bd40c8d4aa86e0cb85e
This patch provides the following changes:
- Adds definition for FEAT_MTE3 value in ID_AA64PFR1_EL1 register
- Enables Memory Tagging Extension for FEAT_MTE3.
Change-Id: I735988575466fdc083892ec12c1aee89b5faa472
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Enable basic support for Neoverse-N2 CPUs.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I498adc2d9fc61ac6e1af8ece131039410872e8ad
This patch provides the changes listed below:
- Adds new bit fields definitions for SCTLR_EL1/2 registers
- Corrects the name of SCTLR_EL1/2.[20] bit field from
SCTLR_UWXN_BIT to SCTLR_TSCXT_BIT
- Adds FEAT_PANx bit field definitions and their possible
values for ID_AA64MMFR1_EL1 register.
- Adds setting of SCTLR_EL1.SPAN bit to preserve PSTATE.PAN
on taking an exception to EL1 in spm_sp_setup() function
(services\std_svc\spm_mm\spm_mm_setup.c)
Change-Id: If51f20e7995c649126a7728a4d0867041fdade19
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This errata workaround did not work as intended and was revised in
subsequent SDEN releases so we are reverting this change.
This is the patch being reverted:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/4686
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I8554c75d7217331c7effd781b5f7f49b781bbebe
This errata workaround did not work as intended and was revised in
subsequent SDEN releases so we are reverting this change.
This is the patch being reverted:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/4684
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I560749a5b55e22fbe49d3f428a8b9545d6bdaaf0
Currently, when RECLAIM_INIT_CODE is set, the
stacks are scaled to ensure that the entirety
of the init section can be reclaimed as stack.
This causes an issue in lib/psci/aarch64/psci_helpers.S,
where the stack size is used for cache operations in
psci_do_pwrdown_cache_maintenance(). If the stacks
are scaled, then the PSCI code may fail to invalidate
some of the stack memory before power down.
Resizing stacks is also not good for stability in general,
since code that works with a small number of cores may
overflow the stack when the number of cores is increased.
Change to make every stack be PLATFORM_STACK_SIZE big,
and allow the total stack to be smaller than the
init section.
Any pages of the init section not reclaimed as
stack will be set to read-only and execute-never,
for security.
Change-Id: I10b3884981006431f2fcbec3864c81d4a8c246e8
Signed-off-by: David Horstmann <david.horstmann@arm.com>
When issuing barrier instructions like DSB or DMB, we must make sure
that the compiler does not undermine out efforts to fence off
instructions. Currently the compiler is free to move the barrier
instruction around, in respect to former or later memory access
statements, which is not what we want.
Add a compiler barrier to the inline assembly statement in our
DEFINE_SYSOP_TYPE_FUNC macro, to make sure memory accesses are not
reordered by the compiler.
This is in line with Linux' definition:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm64/include/asm/barrier.h
Since those instructions share a definition, apart from DSB and DMB this
now also covers some TLBI instructions. Having a compiler barrier there
also is useful, although we probably have stronger barriers in place
already.
Change-Id: If6fe97b13a562643a643efc507cb4aad29daa5b6
Reported-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To support platforms without Trusted DRAM this patch defines
PLAT_ARM_SPMC_BASE and enables platform to use either Trusted DRAM or
DRAM region behind TZC.
Change-Id: Icaa5c7d33334258ff27e8e0bfd0812c304e68ae4
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Retrieve peripheral base address from a define instead of
parsing the device tree. The goal is to improve execution time.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I2588c53ad3d4abcc3d7fe156458434a7940dd72b
Usually, C has no problem up-converting types to larger bit sizes. MISRA
rule 10.7 requires that you not do this, or be very explicit about this.
This resolves the following required rule:
bl1/aarch64/bl1_context_mgmt.c:81:[MISRA C-2012 Rule 10.7 (required)]<None>
The width of the composite expression "0U | ((mode & 3U) << 2U) | 1U |
0x3c0U" (32 bits) is less that the right hand operand
"18446744073709547519ULL" (64 bits).
This also resolves MISRA defects such as:
bl2/aarch64/bl2arch_setup.c:18:[MISRA C-2012 Rule 12.2 (required)]
In the expression "3U << 20", shifting more than 7 bits, the number
of bits in the essential type of the left expression, "3U", is
not allowed.
Further, MISRA requires that all shifts don't overflow. The definition of
PAGE_SIZE was (1U << 12), and 1U is 8 bits. This caused about 50 issues.
This fixes the violation by changing the definition to 1UL << 12. Since
this uses 32bits, it should not create any issues for aarch32.
This patch also contains a fix for a build failure in the sun50i_a64
platform. Specifically, these misra fixes removed a single and
instruction,
92407e73 and x19, x19, #0xffffffff
from the cm_setup_context function caused a relocation in
psci_cpus_on_start to require a linker-generated stub. This increased the
size of the .text section and caused an alignment later on to go over a
page boundary and round up to the end of RAM before placing the .data
section. This sectionn is of non-zero size and therefore causes a link
error.
The fix included in this reorders the functions during link time
without changing their ording with respect to alignment.
Change-Id: I76b4b662c3d262296728a8b9aab7a33b02087f16
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
And from crash_console_flush.
We ignore the error information return by console_flush in _every_
place where we call it, and casting the return type to void does not
work around the MISRA violation that this causes. Instead, we collect
the error information from the driver (to avoid changing that API), and
don't return it to the caller.
Change-Id: I1e35afe01764d5c8f0efd04f8949d333ffb688c1
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
This patch updates the MIDR value for rainier cpu.
Change-Id: I99a5d96f757239cf65b2688095c4ec66cd991cf9
Signed-off-by: Jagadeesh Ujja <jagadeesh.ujja@arm.com>
Cortex A77 erratum 1925769 is a Cat B erratum, present in older
revisions of the Cortex A77 processor core. The workaround is to
set bit 8 in the ECTLR_EL1 register, there is a small performance cost
(<0.5%) for setting this bit.
SDEN can be found here:
https://documentation-service.arm.com/static/5f7c35d0d3be967f7be46d33
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I9cf0e0b5dc1e3e32e24279d2632c759cc7bd7ce9
Update the libfdt source files, the upstream commit is 73e0f143b73d
("libfdt: fdt_strerror(): Fix comparison warning").
This brings us the fixes for the signed/unsigned comparison warnings,
so platforms can enable -Wsign-compare now.
Change-Id: I303d891c82ffea0acefdde27289339db5ac5a289
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch migrates the mbedcrypto dependency for TF-A
to mbedTLS repo v2.24.0 which is the latest release tag.
The relevant documentation is updated to reflect the
use of new version.
Change-Id: I116f44242e8c98e856416ea871d11abd3234dac1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
* changes:
arm_fpga: Add platform documentation
arm_fpga: Add post-build linker script
arm_fpga: Add ROM trampoline
arm_fpga: Add devicetree file
arm_fpga: Remove SPE PMU DT node if SPE is not available
arm_fpga: Adjust GICR size in DT to match number of cores
fdt: Add function to adjust GICv3 redistributor size
drivers: arm: gicv3: Allow detecting number of cores
We now have code to detect the CPU topology at runtime, and can also
populate the CPU nodes in a devicetree accordingly. This is used by the
ARM FPGA port, for instance.
But also a GICv3 compatible interrupt controller provides MMIO frames
per core, so the size of this region needs to be adjusted in the DT,
to match the number of cores as well.
Provide a generic function to find the GICv3 interrupt controller in
the DT, then adjust the "reg" entry to match the number of detected
cores. Since the size of the GICR frame per cores differs between
GICv4 and GICv3, this size is supplied as a parameter to the function.
The caller should determine the applicable value by either hardcoding
it or by observing GICR_TYPER.VLPIS.
Change-Id: Ic2a6445c2c5381a36bf24263f52fcbefad378c05
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
A GICv3 interrupt controller will be instantiated for a certain number
of cores. This will result in the respective number of GICR frames. The
last frame will have the "Last" bit set in its GICR_TYPER register.
For platforms with a topology unknown at build time (the Arm FPGAs, for
instance), we need to learn the number of used cores at runtime, to size
the GICR region in the devicetree accordingly.
Add a generic function that iterates over all GICR frames until it
encounters one with the "Last" bit set. It returns the number of cores
the GICv3 has been configured for.
Change-Id: I79f033c50dfc1c275aba7122725868811abcc4f8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
* changes:
plat/arm: Add platform support for Morello
fdts: add device tree sources for morello platform
lib/cpus: add support for Morello Rainier CPUs
This patch adds CPU support for the Rainier CPU which is
derived from Neoverse N1 r4p0 CPU and implements the
Morello capability architecture.
Change-Id: Ic6b796481da5a66504ecb0648879446edf4c69fb
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
Cortex A77 erratum 1508412 is a Cat B Errata present in r0p0 and r1p0.
The workaround is a write sequence to several implementation defined
registers based on A77 revision.
This errata is explained in this SDEN:
https://static.docs.arm.com/101992/0010/Arm_Cortex_A77_MP074_Software_Developer_Errata_Notice_v10.pdf
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I217993cffb3ac57c313db8490e7b8a7bb393379b
This patch allows the system to fallback to a default CPU library
in case the MPID does not match with any of the supported ones.
This feature can be enabled by setting SUPPORT_UNKNOWN_MPID build
option to 1 (enabled by default only on arm_fpga platform).
This feature can be very dangerous on a production image and
therefore it MUST be disabled for Release images.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I0df7ef2b012d7d60a4fd5de44dea1fbbb46881ba
Depending on compiler, the issue about bool or uint*_t not defined can
appear.
Correct this by adding stdbool.h and stdint.h includes in etzpc.h.
Change-Id: If1419dc511efbe682459fa4a776481fa52a38aa3
Signed-off-by: Yann Gautier <yann.gautier@st.com>
nand_wait_ready is called with a millisecond delay
but the timeout used a micro second. Fixing the conversion
in the timeout call.
The prototype of the function is also changed to use an unsigned int
parameter.
Change-Id: Ia3281be7980477dfbfdb842308d35ecd8b926fb8
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
There is one dtsi file per SoC version:
- STM32MP151: common part for all version, Single Cortex-A7
- STM32MP153: Dual Cortex-A7
- STM32MP157: + GPU and DSI, but not needed for TF-A
The STM32MP15xC include a cryptography peripheral, add it in a dedicated
file.
There are 4 packages available, for which the IOs number change. Have one
file for each package. The 2 packages AB and AD are added.
STM32157A-DK1 and STM32MP157C-DK2 share most of their features, a common
dkx file is then created.
Some reordering is done in other files, and realign with kernel DT files.
The DDR files are generated with our internal tool, no changes in the
registers values.
Change-Id: I9f2ef00306310abe34b94c2f10fc7a77a10493d1
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Builds in Debug mode with Measured Boot enabled might run out of trusted
SRAM. This patch allows to change the Log Level at which the Measured Boot
driver will dump the event log, so the latter can be accessed even on
Release builds if necessary, saving space on RAM.
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I133689e313776cb3f231b774c26cbca4760fa120
From commit: 21571b1d140ae7bb44e94c0afba2ec61456b275b
Made small changes to fit into TF-A project
Change-Id: I991f653a7ace04f9c84bcda78ad8d7114ea18e93
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Implemented a parser which populates the properties of
the CoT descriptors as per the binding document [1].
'COT_DESC_IN_DTB' build option is disabled by default and can
be enabled in future for all Arm platforms by making necessary
changes in the memory map.
Currently, this parser is tested only for FVP platform.
[1]:
https://trustedfirmware-a.readthedocs.io/en/latest/components/cot-binding.html
Change-Id: I2f911206087a1a2942aa728de151d2ac269d27cc
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
It uses the existing implementation of snprintf() function
Change-Id: Ie59418564c2e415222e819cf322c34e9a4d1f336
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
From commit: 21571b1d140ae7bb44e94c0afba2ec61456b275b
Made small changes to fit into TF-A project
Change-Id: I07fd7fe1037857f6b299c35367c104fb51fa5cfa
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
The API can be used to invoke a 'stop_func' callback for all
other cores from any initiating core. Optionally it can also
wait for other cores to power down. There may be various use
of such API by platform. Ex: Platform may use this to power
down all other cores from a crashed core.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Change-Id: I4f9dc8a38d419f299c021535d5f1bcc6883106f9
The DSU contains system control registers in the SCU and L3 logic to
control the functionality of the cluster. If "DIRECT CONNECT" L3
memory system variant is used, there won't be any L3 cache,
snoop filter, and SCU logic present hence no system control register
will be present. Hence check SCU presence before accessing DSU register
for DSU_936184 errata.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Change-Id: I1ffa8afb0447ae3bd1032c9dd678d68021fe5a63
This patch creates and populates the /cpus node in a device tree
based on the existing topology. It uses the minimum required nodes
and properties to satisfy the binding as specified in
https://www.kernel.org/doc/Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Javier Almansa Sobrino <javier.almansasobrino@arm.com>
Change-Id: I03bf4e9a6427da0a3b8ed013f93d7bc43b5c4df0
This patch introduces support for PN9 variant for some
Denver based platforms.
Original change by: Hemant Nigam <hnigam@nvidia.com>
Signed-off-by: Kalyani Chidambaram Vaidyanathan <kalyanic@nvidia.com>
Change-Id: I331cd3a083721fd1cd1b03f4a11b32fd306a21f3
Using the Fconf, register base address of the various nv-counters
(currently, trusted, non-trusted nv-counters) are moved to the
device tree and retrieved during run-time. This feature is
enabled using the build option COT_DESC_IN_DTB.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I236f532e63cea63b179f60892cb406fc05cd5830
Created a header file defining the id of the various nv-counters
used in the system.
Also, updated the device tree to add 'id' property for the trusted
and non-trusted nv-counters.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ia41a557f7e56ad4ed536aee11c7a59e078ae07c0
'EHF' is used by RAS, SDEI, SPM_MM common frameworks.
If platform needs to plug-in specific handlers then
'PLAT_EHF_DESC' can be used to populate platform specific
priority levels.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Change-Id: I37af7e0e48111f87b6982604bf5c15db3e05755d
FF-A interface to handle SPMC to SPMD direct messages requests.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: Ia707a308c55561a31dcfa86e554ea1c9e23f862a
In case of AT speculative workaround applied, page table walk
is disabled for lower ELs (EL1 and EL0) in EL3.
Hence added a wrapper function which temporarily enables page
table walk to execute AT instruction for lower ELs and then
disables page table walk.
Execute AT instructions directly for lower ELs (EL1 and EL0)
assuming page table walk is enabled always when AT speculative
workaround is not applied.
Change-Id: I4ad4c0bcbb761448af257e9f72ae979473c0dde8
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
As per latest mailing communication [1], we decided to
update AT speculative workaround implementation in order to
disable page table walk for lower ELs(EL1 or EL0) immediately
after context switching to EL3 from lower ELs.
Previous implementation of AT speculative workaround is available
here: 45aecff00
AT speculative workaround is updated as below:
1. Avoid saving and restoring of SCTLR and TCR registers for EL1
in context save and restore routine respectively.
2. On EL3 entry, save SCTLR and TCR registers for EL1.
3. On EL3 entry, update EL1 system registers to disable stage 1
page table walk for lower ELs (EL1 and EL0) and enable EL1
MMU.
4. On EL3 exit, restore SCTLR and TCR registers for EL1 which
are saved in step 2.
[1]:
https://lists.trustedfirmware.org/pipermail/tf-a/2020-July/000586.html
Change-Id: Iee8de16f81dc970a8f492726f2ddd57e7bd9ffb5
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
SCTLR and TCR registers of EL1 plays role in enabling/disabling of
page table walk for lower ELs (EL0 and EL1).
Hence re-arranged EL1 context offsets to have SCTLR and TCR registers
values one after another in the stack so that these registers values
can be saved and restored using stp and ldp instruction respectively.
Change-Id: Iaa28fd9eba82a60932b6b6d85ec8857a9acd5f8b
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
* changes:
SPM: Add owner field to cactus secure partitions
SPM: Alter sp_gen.mk entry depending on owner of partition
plat/arm: enable support for Plat owned SPs
For Arm platforms SPs are loaded by parsing tb_fw_config.dts and
adding them to SP structure sequentially, which in-turn is appended to
loadable image list.
With recently introduced dualroot CoT for SPs where they are owned
either by SiP or by Platform. SiP owned SPs index starts at SP_PKG1_ID
and Plat owned SPs index starts at SP_PKG5_ID. As the start index of SP
depends on the owner, there should be a mechanism to parse owner of a SP
and put it at the correct index in SP structure.
This patch adds support for parsing a new optional field "owner" and
based on it put SP details(UUID & Load-address) at the correct index in
SP structure.
Change-Id: Ibd255b60d5c45023cc7fdb10971bef6626cb560b
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
We relyed on the default signed-ness of constants, which is usually
signed. This can create MISRA violations, such as:
bl1/bl1_main.c:257:[MISRA C-2012 10.8 (required)] Cast of composite
expression off essential type signed to essential type unsigned
These constants were only used as unsigned, so this patch makes them
explicitly unsigned.
Change-Id: I5f1310c881e936077035fbb1d5ffb449b45de3ad
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
There was a collision between the name of the typedef in the CASSERT and
something else, so we make the name of the typedef unique to the
invocation of DEFFINE_SVC_UUID2 by appending the name that's passed into
the macro. This eliminates the following MISRA violation:
bl1/bl1_main.c:233:[MISRA C-2012 Rule 5.6 (required)] Identifier
"invalid_svc_uuid" is already used to represent a typedef.
This also resolves MISRA rule 5.9.
These renamings are as follows:
* tzram -> secram. This matches the function call name as it has
sec_mem in it's name
* fw_config_base -> config_base. This file does not mess with
hw_conig, so there's little chance of confusion
Change-Id: I8734ba0956140c8e29b89d0596d10d61a6ef351e
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
For dualroot CoT there are two sets of SP certificates, one owned by
Silicon Provider(SiP) and other owned by Platform. Each certificate can
have a maximum of 4 SPs.
This patch reduces the number of SiP owned SPs from 8 to 4 and adds
the remaining 4 to Plat owned SP.
Plat owned SP certificate is signed using Platform RoT key and
protected against anti-rollback using the Non-trusted Non-volatile
counter.
Change-Id: Idc3ddd87d6d85a5506a7435f45a6ec17c4c50425
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Add support to generate a certificate named "plat-sp-cert" for Secure
Partitions(SP) owned by Platform.
Earlier a single certificate file "sip-sp-cert" was generated which
contained hash of all 8 SPs, with this change SPs are divided into
two categories viz "SiP owned" and "Plat owned" containing 4 SPs each.
Platform RoT key pair is used for signing.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I5bd493cfce4cf3fc14b87c8ed1045f633d0c92b6
ERRATA ID: RES-3033912 - Internal Address Space Init state causes
a hang upon accesses to [0xf070_0000, 0xf07f_ffff]
Workaround: Boot Firmware (ATF) should configure CCU_RGF_WIN(4) to
split [0x6e_0000, 0xff_ffff] to values [0x6e_0000, 0x6f_ffff] and
[0x80_0000, 0xff_ffff] that cause accesses to the segment of
[0xf070_0000, 0xf07f_ffff] to act as RAZWI. Reuse common
work-around code for both AP806 and AP807.
Change-Id: Ia91a4802d02917d1682faa0c81571093d1687d97
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
This patch fixes the bug when AMUv1 group1 counters was
always assumed being implemented without checking for its
presence which was causing exception otherwise.
The AMU extension code was also modified as listed below:
- Added detection of AMUv1 for ARMv8.6
- 'PLAT_AMU_GROUP1_NR_COUNTERS' build option is removed and
number of group1 counters 'AMU_GROUP1_NR_COUNTERS' is now
calculated based on 'AMU_GROUP1_COUNTERS_MASK' value
- Added bit fields definitions and access functions for
AMCFGR_EL0/AMCFGR and AMCGCR_EL0/AMCGCR registers
- Unification of amu.c Aarch64 and Aarch32 source files
- Bug fixes and TF-A coding style compliant changes.
Change-Id: I14e407be62c3026ebc674ec7045e240ccb71e1fb
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
BL31 binary size is aligned to 4KB because of the
code in include\plat\arm\common\arm_reclaim_init.ld.S:
__INIT_CODE_UNALIGNED__ = .;
. = ALIGN(PAGE_SIZE);
__INIT_CODE_END__ = .;
with all the zero data after the last instruction of
BL31 code to the end of the page.
This causes increase in size of BL31 binary stored in FIP
and its loading time by BL2.
This patch reduces the size of BL31 image by moving
page alignment from __INIT_CODE_END__ to __STACKS_END__
which also increases the stack size for secondary CPUs.
Change-Id: Ie2ec503fc774c22c12ec506d74fd3ef2b0b183a9
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch adds support for additional Denver MIDRs to
cover all the current SKUs.
Change-Id: I85d0ffe9b3cb351f430ca7d7065a2609968a7a28
Signed-off-by: Alex Van Brunt <avanbrunt@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Currently only single signing domain is supported for SP packages but
there is plan to support dual signing domains if CoT is dualroot.
SP_CONTENT_CERT_ID is the certificate file which is currently generated
and signed with trusted world key which in-turn is derived from Silicon
provider RoT key.
To allow dual signing domain for SP packages, other certificate file
will be derived from Platform owned RoT key.
This patch renames "SP_CONTENT_CERT_ID" to "SIP_SP_CONTENT_CERT_ID" and
does other related changes.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I0bc445a3ab257e2dac03faa64f46e36a9fed5e93
Provide manifest and build options to boot OP-TEE as a
guest S-EL1 Secure Partition on top of Hafnium in S-EL2.
Increase ARM_SP_MAX_SIZE to cope with OP-TEE debug build image.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Idd2686fa689a78fe2d05ed92b1d23c65e2edd4cb
Add CN913x case to bl2_plat_get_cp_count.
Fix loading of cp1/2 image. This is a preparation
patch for adding CN913x SoC family support.
Change-Id: Id84a30203d20572fc0dfd3f91ea395c199a85fe9
Signed-off-by: Ben Peled <bpeled@marvell.com>
This patch fixes defects 10.3, 10.4, 10.7, 20.7
reported by MISRA-2012 scan and adds braces for
conditional statements according to the TF-A
coding style.
Change-Id: If84ed31cdd55bc8e7cdd2a5f48c0dacc25792112
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Currently, 'SMCCC_ARCH_FEATURES' SMC call handler unconditionally
returns 'SMC_OK' for 'SMCCC_ARCH_SOC_ID' function. This seems to
be not correct for the platform which doesn't implement soc-id
functionality i.e. functions to retrieve both soc-version and
soc-revision.
Hence introduced a platform function which will check whether SMCCC
feature is available for the platform.
Also, updated porting guide for the newly added platform function.
Change-Id: I389f0ef6b0837bb24c712aa995b7176117bc7961
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
This reverts commit 11af40b630, reversing
changes made to 2afcf1d4b8.
This errata workaround did not work as intended so we are reverting this
change. In the future, when the corrected workaround is published in an
SDEN, we will push a new workaround.
This is the patch being reverted:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/4750
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I20aa064c1bac9671939e657bec269d32b9e75a97
In BL2, fw_config's population happened before the cache gets
enabled.
Hence to boost the performance, moved fw_config's population
after cache gets enabled (i.e. after MMU gets enabled).
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I2e75cabd76b1cb7a660f6b72f409ab40d2877284
Updated the function 'set_fw_config_info' to make it generic
by doing below changes:
1. Rename function name from 'set_fw_config_info' to 'set_config_info'
2. Take image_id as an argument so that this function can set any
config information.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Icf29e19d3e9996d8154d84dbbbc76712fab0f0c1
Update the data type of the member 'config_max_size' present in the
structure 'dyn_cfg_dtb_info_t' to uint32_t.
This change is being done so that dyn_cfg_dtb_info_t and image_info
structure should use same data type for maximum size.
Change-Id: I9b5927a47eb8351bbf3664b8b1e047ae1ae5a260
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
* changes:
plat/arm/board/fvp: Add support for Measured Boot
TF-A: Add support for Measured Boot driver to FCONF
TF-A: Add support for Measured Boot driver in BL1 and BL2
TF-A: Add Event Log for Measured Boot
TF-A: Add support for Measured Boot driver
This patch adds support for Event Log generation required
for Measured Boot functionality.
Change-Id: I34f05a33565e6659e78499d62cc6fb00b7d6c2dc
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch adds support for Measured Boot driver functionality
in common Arm platform code.
Change-Id: If049dcf8d847c39023b77c0d805a8cf5b8bcaa3e
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Getting the actual size of a DTB blob is useful beyond the Raspberry Pi
port, so let's move this helper to a common header.
Change-Id: Ia5be46e9353ca859a1e5ad9e3c057a322dfe22e2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch redefines 'true' and 'false' definitions in
'include/lib/libc/stdbool.h' to fix defect reported by
MISRA C-2012 Rule 10.1
"The expression \"0\" of non-boolean essential type is
being interpreted as a boolean value for the operator \"? :\"."
Change-Id: Ie1b16e5826e5427cc272bd753e15d4d283e1ee4c
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
- Fix the line address macro
- LLC invalidate and enable before ways lock for allocation
- Add support for limited SRAM size allocation
- Add SRAM RW test function
Change-Id: I1867ece3047566ddd7931bd7472e1f47fb42c8d4
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Included cot_descriptors.dtsi in platform device tree
(fvp_tb_fw_config.dts).
Also, updated the maximum size of tb_fw_config to 0x1800
in order to accomodate the device tree for CoT descriptors.
Follow up patch will parse the device tree for these CoT descriptors
and fill the CoT descriptor structures at runtime instead of using
static CoT descriptor structures in the code base.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I90122bc713f6842b82fb019b04caf42629b4f45a
Added CoT descriptor nodes and properties in device tree.
Currently, CoT descriptors which are used by BL2 are added as part
of device tree.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Iff23cff843e5489fac18bcee5f5d6a71de5ad0d0
Introduce stm32mp1_register_clock_parents_secure() in stm32mp1
clock driver to allow platform shared resources to register as
secure the parent clocks of a clock registered as secure.
Change-Id: I53a9ab6aa78ee840ededce67e7b12a84e08ee843
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
The .rela.dyn section is the same for BL2-AT-EL3, BL31, TSP.
Move it to the common header file.
I slightly changed the definition so that we can do "RELA_SECTION >RAM".
It still produced equivalent elf images.
Please note I got rid of '.' from the VMA field. Otherwise, if the end
of previous .data section is not 8-byte aligned, it fails to link.
aarch64-linux-gnu-ld.bfd: warning: changing start of section .rela.dyn by 4 bytes
aarch64-linux-gnu-ld.bfd: warning: changing start of section .rela.dyn by 4 bytes
aarch64-linux-gnu-ld.bfd: warning: changing start of section .rela.dyn by 4 bytes
make: *** [Makefile:1071: build/qemu/release/bl31/bl31.elf] Error 1
Change-Id: Iba7422d99c0374d4d9e97e6fd47bae129dba5cc9
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This version corresponds to the following commit <7be250b>
libfdt: Correct condition for reordering blocks
Also, updated the Juno romlib jumptable with fdt APIs.
Change-Id: Ib6d28c1aea81c2144a263958f0792cc4daea7a1f
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
* changes:
plat: marvell: armada: a8k: add OP-TEE OS MMU tables
drivers: marvell: add support for mapping the entire LLC to SRAM
plat: marvell: armada: add LLC SRAM CCU setup for AP806/AP807 platforms
plat: marvell: armada: reduce memory size reserved for FIP image
plat: marvell: armada: platform definitions cleanup
plat: marvell: armada: a8k: check CCU window state before loading MSS BL2
drivers: marvell: add CCU driver API for window state checking
drivers: marvell: align and extend llc macros
plat: marvell: a8k: move address config of cp1/2 to BL2
plat: marvell: armada: re-enable BL32_BASE definition
plat: marvell: a8k: extend includes to take advantage of the phy_porting_layer
marvell: comphy: initialize common phy selector for AP mode
marvell: comphy: update rx_training procedure
plat: marvell: armada: configure amb for all CPs
plat: marvell: armada: modify PLAT_FAMILY name for 37xx SoCs
* changes:
doc: Update memory layout for firmware configuration area
plat/arm: Increase size of firmware configuration area
plat/arm: Load and populate fw_config and tb_fw_config
fconf: Handle error from fconf_load_config
plat/arm: Update the fw_config load call and populate it's information
fconf: Allow fconf to load additional firmware configuration
fconf: Clean confused naming between TB_FW and FW_CONFIG
tbbr/dualroot: Add fw_config image in chain of trust
cert_tool: Update cert_tool for fw_config image support
fiptool: Add fw_config in FIP
plat/arm: Rentroduce tb_fw_config device tree
Neoverse N1 erratum 1800710 is a Cat B erratum, present in older
revisions of the Neoverse N1 processor core. The workaround is to
set a bit in the ECTLR_EL1 system register, which disables allocation
of splintered pages in the L2 TLB.
This errata is explained in this SDEN:
https://static.docs.arm.com/sden885747/f/Arm_Neoverse_N1_MP050_Software_Developer_Errata_Notice_v21.pdf
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Ie5b15c8bc3235e474a06a57c3ec70684361857a6
Cortex A77 erratum 1800714 is a Cat B erratum, present in older
revisions of the Cortex A77 processor core. The workaround is to
set a bit in the ECTLR_EL1 system register, which disables allocation
of splintered pages in the L2 TLB.
Since this is the first errata workaround implemented for Cortex A77,
this patch also adds the required cortex_a77_reset_func in the file
lib/cpus/aarch64/cortex_a77.S.
This errata is explained in this SDEN:
https://static.docs.arm.com/101992/0010/Arm_Cortex_A77_MP074_Software_Developer_Errata_Notice_v10.pdf
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I844de34ee1bd0268f80794e2d9542de2f30fd3ad
Increased the size of firmware configuration area to accommodate
all configs.
Updated maximum size of following bootloaders due to increase
in firmware configs size and addition of the code in the BL2.
1. Increased maximum size of BL2 for Juno platform in no
optimisation case.
2. Reduced maximum size of BL31 for fvp and Juno platform.
3. Reduced maximum size of BL32 for Juno platform.
Change-Id: Ifba0564df0d1fe86175bed9fae87fdcf013b1831
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Modified the code to do below changes:
1. Load tb_fw_config along with fw_config by BL1.
2. Populate fw_config device tree information in the
BL1 to load tb_fw_config.
3. In BL2, populate fw_config information to retrieve
the address of tb_fw_config and then tb_fw_config
gets populated using retrieved address.
4. Avoid processing of configuration file in case of error
value returned from "fw_config_load" function.
5. Updated entrypoint information for BL2 image so
that it's arg0 should point to fw_config address.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change-Id: Ife6f7b673a074e7f544ee3d1bda7645fd5b2886c
Updated 'fconf_load_config' function to return
the error.
Error from 'fconf_load_config" gets handled
by BL1 in subsequent patches.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I4360f4df850e355b5762bb2d9666eb285101bc68
Modified the `fconf_load_config` function so that it can
additionally support loading of tb_fw_config along with
fw_config.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ie060121d367ba12e3fcac5b8ff169d415a5c2bcd
Cleaned up confused naming between TB_FW and FW_CONFIG.
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I9e9f6e6ca076d38fee0388f97d370431ae067f08
Updated cert_tool to add hash information of fw_config image into
the existing "trusted boot fw" certificate.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I720319225925806a2a9f50a1ac9c8a464be975f0
Added support in fiptool to include fw_config image
in FIP.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ibbd14723a4141598d9d7f6bfcf88a0ef92cf87bc
Change handler of FFA version interface:
- Return SPMD's version if the origin of the call is secure;
- Return SPMC's version if origin is non-secure.
Signed-off-by: J-Alves <joao.alves@arm.com>
Change-Id: I0d1554da79b72b1e02da6cc363a2288119c32f44
Cortex A76 erratum 1800710 is a Cat B erratum, present in older
revisions of the Cortex A76 processor core. The workaround is to
set a bit in the ECTLR_EL1 system register, which disables allocation
of splintered pages in the L2 TLB.
This errata is explained in this SDEN:
https://static.docs.arm.com/sden885749/g/Arm_Cortex_A76_MP052_Software_Developer_Errata_Notice_v20.pdf
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Ifc34f2e9e053dcee6a108cfb7df7ff7f497c9493
Cortex A76 erratum 1791580 is a Cat B erratum present in earlier
revisions of the Cortex A76. The workaround is to set a bit in the
implementation defined CPUACTLR2 register, which forces atomic store
operations to write-back memory to be performed in the L1 data cache.
This errata is explained in this SDEN:
https://static.docs.arm.com/sden885749/g/Arm_Cortex_A76_MP052_Software_Developer_Errata_Notice_v20.pdf
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Iefd58159b3f2e2286138993317b98e57dc361925
* changes:
drivers/scmi-msg: smt entry points for incoming messages
drivers/scmi-msg: support for reset domain protocol
drivers/scmi-msg: support for clock protocol
drivers/scmi-msg: driver for processing scmi messages
It is desired to have the peripheral writes completed to clear the
interrupt condition and de-assert the interrupt request to GIC before
EOI write. Failing which spurious interrupt will occurred.
A barrier is needed to ensure peripheral register write transfers are
complete before EOI is done.
GICv2 memory mapped DEVICE nGnR(n)E writes are ordered from core point
of view. However these writes may pass over different interconnects,
bridges, buffers leaving some rare chances for the actual write to
complete out of order.
GICv3 ICC EOI system register writes have no ordering against nGnR(n)E
memory writes as they are over different interfaces.
Hence a dsb can ensure from core no writes are issued before the previous
writes are *complete*.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Change-Id: Ie6362009e2f91955be99dca8ece14ade7b4811d6
Adjust the latest OP-TEE memory definitions to the
newest TF-A baseline.
Change-Id: Ib9c82b85f868adaf3c7285eb340486bda9c59c36
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add llc_sram_enable() and llc_sram_disable() APIs to Marvell
cache_lls driver.
Add LLC_SRAM definition to Marvell common makefile - disabled
by the default.
Add description of LLC_SRAM flag to the build documentation.
Change-Id: Ib348e09752ce1206d29268ef96c9018b781db182
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Add ccu_is_win_enabled() API for checking the CCU window
state using AP and window indexes.
Change-Id: Ib955a2cac28b2729b0a763f3bbbea28b476a2fe4
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Make all LLC-related macros to start with the same prefix
Add more LLC control registers definitions
This patch is a preparation step for LLC SRAM support
Change-Id: I0a4f0fc83e8ef35be93dd239a85f2a9f88d1ab19
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
As a preparation to support proper loading the OPTEE OS image,
enable the BL32 specific defines in case the SPD is used.
On the occasion move two BL32-related macros to marvell_def.h
and fix BL32_LIMIT definition.
Change-Id: Id4e2d81833bc1895650cca8b0fc0bfc341cf77f3
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
The Marvell Armada 37xx SoCs-based platforms contain a bit
awkward directory structure because the currently only one
supported PLAT and PLAT_FAMILY are the same. Modify the latter
to 'a3k' in order to improve it and keep plat/marvell/armada
tree more consistent:
plat/marvell/
├── armada
│ ├── a3k
│ │ ├── a3700
[...]
│ ├── a8k
│ │ ├── a70x0
[...]
Change-Id: I693a6ef88e6ce49a326a3328875c90bbc186066a
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble: ap807: clean-up PLL configuration sequence
ddr: a80x0: add DDR 32-bit mode support
plat: marvell: mci: perform mci link tuning for all mci interfaces
plat: marvell: mci: use more meaningful name for mci link tuning
plat: marvell: a8k: remove wrong or unnecessary comments
plat: marvell: ap807: enable snoop filter for ap807
plat: marvell: ap807: update configuration space of each CP
plat: marvell: ap807: use correct address for MCIx4 register
plat: marvell: add support for PLL 2.2GHz mode
plat: marvell: armada: make a8k_common.mk and mss_common.mk more generic
marvell: armada: add extra level in marvell platform hierarchy
This change implements SCMI channels for reading a SCMI message from a
shared memory and call the SCMI message drivers to route the message
to the target platform services.
SMT refers to the shared memory management protocol which is used
to get/put message/response in shared memory. SMT is a 28byte header
stating shared memory state and exchanged protocol data.
The processing entry for a SCMI message can be a secure interrupt
or fastcall SMCCC invocation.
SMT description in this implementation is based on the OP-TEE
project [1] itself based in the SCP-firmware implementation [2].
Link: [1] a58c4d706d
Link: [2] https://github.com/ARM-software/SCP-firmware.git
Change-Id: I416c7dab5c67954c6fe80bae8d8cdfdcda66873e
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Adds SCMI reset domain protocol support in the SCMI message drivers
as defined in SCMI specification v2.0 [1]. Not all the messages
defined in the specification are supported.
scmi_msg_get_rd_handler() sanitizes the message_id value
against any speculative use of reset domain ID as a index since by
SCMI specification, IDs are indices.
This implementation is based on the OP-TEE project implementation [2]
itself based on the SCP-firmware implementation [3] of the SCMI
protocol server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] 56a1f10ed9
Link: [3] https://github.com/ARM-software/SCP-firmware.git
Change-Id: If7cf13de40a815dedb40dcd5af8b6bb6725d9078
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Adds SCMI clock protocol support in the SCMI message drivers as
defined in SCMI specification v2.0 [1] for clock protocol messages.
Platform can provide one of the plat_scmi_clock_*() handler for the
supported operations set/get state/rate and others.
scmi_msg_get_clock_handler() sanitizes the message_id value
against any speculative use of clock ID as a index since by
SCMI specification, IDs are indices.
This implementation is based on the OP-TEE project implementation [2]
itself based on the SCP-firmware implementation [3] of the SCMI
protocol server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] a7a9e3ba71
Link: [3] https://github.com/ARM-software/SCP-firmware.git
Change-Id: Ib56e096512042d4f7b9563d1e4181554eb8ed02c
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
This change introduces drivers to allow a platform to create a basic
SCMI service and register handlers for client request (SCMI agent) on
system resources. This is the first piece of the drivers: an entry
function, the SCMI base protocol support and helpers for create
the response message.
With this change, scmi_process_message() is the entry function to
process an incoming SCMI message. The function expect the message
is already copied from shared memory into secure memory. The message
structure stores message reference and output buffer reference where
response message shall be stored.
scmi_process_message() calls the SCMI protocol driver according to
the protocol ID in the message. The SCMI protocol driver will call
defined platform handlers according to the message content.
This change introduces only the SCMI base protocol as defined in
SCMI specification v2.0 [1]. Not all the messages defined
in the specification are supported.
The SCMI message implementation is derived from the OP-TEE project [2]
itself based on the SCP-firmware implementation [3] of the SCMI protocol
server side.
Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] ae8c806809
Link: [3] https://github.com/ARM-software/SCP-firmware/tree/v2.6.0
Change-Id: I639c4154a39fca60606264baf8d32452641f45e9
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
This patch adds a build config 'RAS_TRAP_LOWER_EL_ERR_ACCESS' to set
SCR_EL3.TERR during CPU boot. This bit enables trapping RAS register
accesses from EL1 or EL2 to EL3.
RAS_TRAP_LOWER_EL_ERR_ACCESS is disabled by default.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: Ifb0fb0afedea7dd2a29a0b0491a1161ecd241438
This patch adds all Tegra194 RAS nodes definitions and support to
handle all uncorrectable RAS errors.
Change-Id: I109b5a8dbca91d92752dc282c4ca30f273c475f9
Signed-off-by: David Pu <dpu@nvidia.com>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
with sha 0792dd7, support to generate certificate for Secure
Partitions was added for dualroot CoT only, this patch extends
this support for tbbr CoT.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I451c0333536dd1cbe17861d454bdb0dc7a17c63f
Using the fconf framework, the Group 0 and Group 1 secure interrupt
descriptors are moved to device tree and retrieved in runtime. This
feature is enabled by the build flag SEC_INT_DESC_IN_FCONF.
Change-Id: I360c63a83286c7ecc2426cd1ff1b4746d61e633c
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.
This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.
Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
A new certificate "sip-sp-cert" has been added for Silicon Provider(SiP)
owned Secure Partitions(SP). A similar support for Platform owned SP can
be added in future. The certificate is also protected against anti-
rollback using the trusted Non-Volatile counter.
To avoid deviating from TBBR spec, support for SP CoT is only provided
in dualroot.
Secure Partition content certificate is assigned image ID 31 and SP
images follows after it.
The CoT for secure partition look like below.
+------------------+ +-------------------+
| ROTPK/ROTPK Hash |------>| Trusted Key |
+------------------+ | Certificate |
| (Auth Image) |
/+-------------------+
/ |
/ |
/ |
/ |
L v
+------------------+ +-------------------+
| Trusted World |------>| SiP owned SPs |
| Public Key | | Content Cert |
+------------------+ | (Auth Image) |
/ +-------------------+
/ |
/ v|
+------------------+ L +-------------------+
| SP_PKG1 Hash |------>| SP_PKG1 |
| | | (Data Image) |
+------------------+ +-------------------+
. .
. .
. .
+------------------+ +-------------------+
| SP_PKG8 Hash |------>| SP_PKG8 |
| | | (Data Image) |
+------------------+ +-------------------+
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ia31546bac1327a3e0b5d37e8b99c808442d5e53f
Add support to generate certificate "sip-sp-cert" for Secure
Partitions(SP) owned by Silicon provider(SiP).
To avoid deviation from TBBR specification the support is only added for
dualroot CoT and not for TBBR CoT.
A single certificate file is generated containing hash of individual
packages. Maximum 8 secure partitions are supported.
Following new options added to cert_tool:
--sip-sp-cert --> SiP owned Secure Partition Content Certificate
--sp-pkg1 --> Secure Partition Package1 file
--sp-pkg2
.....
--sp-pkg8
Trusted world key pair is used for signing.
Going forward, this feature can be extended for Platfrom owned
Partitions, if required.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ia6dfbc1447cfb41b1fcbd12cf2bf7b88f409bd8d
Remove pll powerdown from pll configuration sequence to improve
stability. Remove redundant cases, which no longer exist.
Also get rid of irrelevant definition of CPU_2200_DDR_1200_RCLK_1200,
which is not used by 806/807.
Change-Id: If911e7dee003dfb9a42fafd7ffe34662f026fd23
Signed-off-by: Alex Leibovich <alexl@marvell.com>
The mci_initialize function name was misleading. The function itself
doesn't initialize MCI in general but performs MCI link tuning for
performance improvement.
Change-Id: I13094ad2235182a14984035bbe58013ebde84a7e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
By default all external CPs start with configuration address space set to
0xf200_0000. To overcome this issue, go in the loop and initialize the
CP one by one, using temporary window configuration which allows to access
each CP and update its configuration space according to decoding
windows scheme defined for each platform.
In case of cn9130 after this procedure bellow addresses will be used:
CP0 - f2000000
CP1 - f4000000
CP2 - f6000000
When the re-configuration is done there is need to restore previous
decoding window configuration(init_io_win).
Change-Id: I1a652bfbd0bf7106930a7a4e949094dc9078a981
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
plat, include/plat) are moved to the new "armada" sub-folder.
Change-Id: Icf03356187078ad6a2e56c9870992be3ca4c9655
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
ETZPC stands for Extended TrustZone Protection Controller. It is a
resource conditional access device. It is mainly based on Arm TZPC.
ST ETZPC exposes memory mapped DECPROT cells to set access permissions
to SoC peripheral interfaces as I2C, SPI, DDR controllers, and some
of the SoC internal memories.
ST ETZPC exposes memory mapped TZMA cells to set access permissions
to some SoC internal memories.
Change-Id: I47ce20ffcfb55306dab923153b71e1bcbe2a5570
Co-developed-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Enhanced Counter Virtualization, ECV, is an architecture extension introduced
in ARMv8.6. This extension allows the hypervisor, at EL2, to setup
self-synchronizing views of the timers for it's EL1 Guests. This patch pokes the
control register to enable this extension when booting a hypervisor at EL2.
Change-Id: I4e929ecdf400cea17eff1de5cf8704aa7e40973d
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
The Fine Grained Traps (FGT) architecture extension was added to aarch64 in
ARMv8.6. This extension primarily allows hypervisors, at EL2, to trap specific
instructions in a more fine grained manner, with an enable bit for each
instruction. This patch adds support for this extension by enabling the
extension when booting an hypervisor at EL2.
Change-Id: Idb9013ed118b6a1b7b76287237096de992ca4da3
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Core spm_mm code expects the translation tables are located in the
inner & outer WBWA & shareable memory.
REGISTER_XLAT_CONTEXT2 macro is used to specify the translation
table section in spm_mm.
In the commit 363830df1c (xlat_tables_v2: merge
REGISTER_XLAT_CONTEXT_{FULL_SPEC,RO_BASE_TABLE}), REGISTER_XLAT_CONTEXT2
macro explicitly specifies the base xlat table goes into .bss by default.
This change affects the existing SynQuacer spm_mm implementation.
plat/socionext/synquacer/include/plat.ld.S linker script intends to
locate ".bss.sp_base_xlat_table" into "sp_xlat_table" section,
but this implementation is no longer available.
This patch adds the base table section name parameter for
REGISTER_XLAT_CONTEXT2 so that platform can specify the
inner & outer WBWA & shareable memory for spm_mm base xlat table.
If PLAT_SP_IMAGE_BASE_XLAT_SECTION_NAME is not defined, base xlat table
goes into .bss by default, the result is same as before.
Change-Id: Ie0e1a235e5bd4288dc376f582d6c44c5df6d31b2
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This should allow git to easily track file moves
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Change-Id: I1592cf39a4f94209c560dc6d1a8bc1bfb21d8327
Changes stm32mp1 reset driver to API to add a timeout argument
to stm32mp_reset_assert() and stm32mp_reset_deassert() and
a return value.
With a supplied timeout, the functions wait the target reset state
is reached before returning. With a timeout of zero, the functions
simply load target reset state in SoC interface and return without
waiting.
Helper functions stm32mp_reset_set() and stm32mp_reset_release()
use a zero timeout and return without a return code.
This change updates few stm32 drivers and plat/stm32mp1 blé_plat_setup.c
accordingly without any functional change.
functional change.
Change-Id: Ia1a73a15125d3055fd8739c125b70bcb9562c27f
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
The patch fixes BL31 linker script error
"Init code ends past the end of the stacks"
for platforms with number of CPUs less than 4,
which is caused by __STACKS_END__ address being
lower than __INIT_CODE_END__.
The modified BL31 linker script detects such cases
and increases the total amount of stack memory,
setting __STACKS_END__ = __INIT_CODE_END__, and
CPUs' stacks are calculated by BL31 'plat_get_my_stack'
function accordingly. For platforms with more than 4 CPUs
and __INIT_CODE_END__ < __STACKS_END__ stack memory does not
increase and allocated CPUs' stacks match the existing
implementation.
The patch removes exclusion of PSCI initialization
functions from the reclaimed .init section in
'arm_reclaim_init.ld.S' script, which increases the
size of reclaimed memory region.
Change-Id: I927773e00dd84e1ffe72f9ee534f4f2fc7b6153c
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch fixes wrong ID_AA64DFR0_EL1 register read instead of
ID_AA64PFR0_EL1 to detect support for MPAM extension.
It also implements get_mpam_version() function which returns
MPAM version as:
0x00: None Armv8.0 or later;
0x01: v0.1 Armv8.4 or later;
0x10: v1.0 Armv8.2 or later;
0x11: v1.1 Armv8.4 or later;
Change-Id: I31d776b1a1b60cb16e5e62296d70adb129d7b760
Reported-by: Matteo Zini <matteozini96@gmail.com>
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
SPCI is renamed as PSA FF-A which stands for Platform Security
Architecture Firmware Framework for A class processors.
This patch replaces the occurrence of SPCI with PSA FF-A(in documents)
or simply FFA(in code).
Change-Id: I4ab10adb9ffeef1ff784641dfafd99f515133760
Signed-off-by: J-Alves <joao.alves@arm.com>
This patch introduces the populate function which leverages
a new driver to extract base address and clk frequency properties
of the uart serial node from HW_CONFIG device tree.
This patch also introduces fdt helper API fdtw_translate_address()
which helps in performing address translation.
Change-Id: I053628065ebddbde0c9cb3aa93d838619f502ee3
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
This patch enables the v8.6 extension to add a delay before WFE traps
are taken. A weak hook plat_arm_set_twedel_scr_el3 has been added in
plat/common/aarch64/plat_common.c that disables this feature by default
but platform-specific code can override it when needed.
The only hook provided sets the TWED fields in SCR_EL3, there are similar
fields in HCR_EL2, SCTLR_EL2, and SCTLR_EL1 to control WFE trap delays in
lower ELs but these should be configured by code running at EL2 and/or EL1
depending on the platform configuration and is outside the scope of TF-A.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I0a9bb814205efeab693a3d0a0623e62144abba2d
Removing FPEXC32_EL2 from the register save/restore routine for EL2
registers since it is already a part of save/restore routine for
fpregs.
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Change-Id: I5ed45fdbf7c8efa8dcfcd96586328d4f6b256bc4
CoT used for BL1 and BL2 are moved to tbbr_cot_bl1.c
and tbbr_cot_bl2.c respectively.
Common CoT used across BL1 and BL2 are moved to
tbbr_cot_common.c.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I2252ac8a6960b3431bcaafdb3ea4fb2d01b79cf5
This patch introduces dynamic configuration for SDEI setup and is supported
when the new build flag SDEI_IN_FCONF is enabled. Instead of using C arrays
and processing the configuration at compile time, the config is moved to
dts files. It will be retrieved at runtime during SDEI init, using the fconf
layer.
Change-Id: If5c35a7517ba00a9f258d7f3e7c8c20cee169a31
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Co-authored-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
During context switching from higher EL (EL2 or higher)
to lower EL can cause incorrect translation in TLB due to
speculative execution of AT instruction using out-of-context
translation regime.
Workaround is implemented as below during EL's (EL1 or EL2)
"context_restore" operation:
1. Disable page table walk using SCTLR.M and TCR.EPD0 & EPD1
bits for EL1 or EL2 (stage1 and stage2 disabled)
2. Save all system registers except TCR and SCTLR (for EL1 and EL2)
3. Do memory barrier operation (isb) to ensure all
system register writes are done.
4. Restore TCR and SCTLR registers (for EL1 and EL2)
Errata details are available for various CPUs as below:
Cortex-A76: 1165522
Cortex-A72: 1319367
Cortex-A57: 1319537
Cortex-A55: 1530923
Cortex-A53: 1530924
More details can be found in mail-chain:
https://lists.trustedfirmware.org/pipermail/tf-a/2020-April/000445.html
Currently, Workaround is implemented as build option which is default
disabled.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: If8545e61f782cb0c2dda7ffbaf50681c825bd2f0
Currently BL2 passes TOS_FW_CONFIG address and size through registers to
BL31. This corresponds to SPMC manifest load address and size. The SPMC
manifest is mapped in BL31 by dynamic mapping. This patch removes BL2
changes from generic code (which were enclosed by SPD=spmd) and retrieves
SPMC manifest size directly from within SPMD. The SPMC manifest load
address is still passed through a register by generic code.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I35c5abd95c616ae25677302f0b1d0c45c51c042f
As a follow-up to bdd2596d4, and related to SPM Dispatcher
EL3 component and SPM Core S-EL2/S-EL1 component: update
with cosmetic and coding rules changes. In addition:
-Add Armv8.4-SecEL2 arch detection helper.
-Add an SPMC context (on current core) get helper.
-Return more meaningful error return codes.
-Remove complexity in few spmd_smc_handler switch-cases.
-Remove unused defines and structures from spmd_private.h
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I99e642450b0dafb19d3218a2f0e2d3107e8ca3fe
Oscillators, PLLs and some system clocks can be related straight to
a parent clock. Prior this change were only oscillators and few
clocks supported by this look up. This changes adds PLLs and other
system clocks. This enables for flexible use of clock tree exploration
when computing a clock frequency value.
Change-Id: I15ec98023a7095e3120a6954de59a4799d92c66b
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
The stdout-path property in the /chosen node of a DTB points to a device
node, which is used for boot console output.
On most (if not all) ARM based platforms this is the debug UART.
The ST platform code contains a function to parse this property and
chase down eventual aliases to learn the node offset of this UART node.
Introduce a slightly more generalised version of this ST platform function
in the generic fdt_wrappers code. This will be useful for other platforms
as well.
Change-Id: Ie6da47ace7833861b5e35fe8cba49835db3659a5
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The STM32 platform port parse DT nodes to find base address to
peripherals. It does this by using its own implementation, even though
this functionality is generic and actually widely useful outside of the
STM32 code.
Re-implement fdt_get_reg_props_by_name() on top of the newly introduced
fdt_get_reg_props_by_index() function, and move it to fdt_wrapper.c.
This is removes the assumption that #address-cells and #size-cells are
always one.
Change-Id: I6d584930262c732b6e0356d98aea50b2654f789d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment the fconf_populate_gicv3_config() implementation is
somewhat incomplete: First it actually fails to store the retrieved
information (the local addr[] array is going nowhere), but also it makes
quite some assumptions about the device tree passed to it: it needs to
use two address-cells and two size-cells, and also requires all five
register regions to be specified, where actually only the first two
are mandatory according to the binding (and needed by our code).
Fix this by introducing a proper generic function to retrieve "reg"
property information from a DT node:
We retrieve the #address-cells and #size-cells properties from the
parent node, then use those to extract the right values from the "reg"
property. The function takes an index to select one region of a reg
property.
This is loosely based on the STM32 implementation using "reg-names",
which we will subsume in a follow-up patch.
Change-Id: Ia59bfdf80aea4e36876c7b6ed4d153e303f482e8
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The STM32 platform code uses its own set of FDT helper functions,
although some of them are fairly generic.
Remove the implementation of fdt_read_uint32_default() and implement it
on top of the newly introduced fdt_read_uint32() function, then convert
all users over.
This also fixes two callers, which were slightly abusing the "default"
semantic.
Change-Id: I570533362b4846e58dd797a92347de3e0e5abb75
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Our fdtw_read_cells() implementation goes to great lengths to
sanity-check every parameter and result, but leaves a big hole open:
The size of the storage the value pointer points at needs to match the
number of cells given. This can't be easily checked at compile time,
since we lose the size information by using a void pointer.
Regardless the current usage of this function is somewhat wrong anyways,
since we use it on single-element, fixed-length properties only, for
which the DT binding specifies the size.
Typically we use those functions dealing with a number of cells in DT
context to deal with *dynamically* sized properties, which depend on
other properties (#size-cells, #clock-cells, ...), to specify the number
of cells needed.
Another problem with the current implementation is the use of
ambiguously sized types (uintptr_t, size_t) together with a certain
expectation about their size. In general there is no relation between
the length of a DT property and the bitness of the code that parses the
DTB: AArch64 code could encounter 32-bit addresses (where the physical
address space is limited to 4GB [1]), while AArch32 code could read
64-bit sized properties (/memory nodes on LPAE systems, [2]).
To make this more clear, fix the potential issues and also align more
with other DT users (Linux and U-Boot), introduce functions to explicitly
read uint32 and uint64 properties. As the other DT consumers, we do this
based on the generic "read array" function.
Convert all users to use either of those two new functions, and make
sure we never use a pointer to anything other than uint32_t or uint64_t
variables directly.
This reveals (and fixes) a bug in plat_spmd_manifest.c, where we write
4 bytes into a uint16_t variable (passed via a void pointer).
Also we change the implementation of the function to better align with
other libfdt users, by using the right types (fdt32_t) and common
variable names (*prop, prop_names).
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi#n874
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/ecx-2000.dts
Change-Id: I718de960515117ac7a3331a1b177d2ec224a3890
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The device tree parsing code for the STM32 platform is using its own FDT
helper functions, some of them being rather generic.
In particular the existing fdt_read_uint32_array() implementation is now
almost identical to the new generic code in fdt_wrappers.c, so we can
remove the ST specific version and adjust the existing callers.
Compared to the original ST implementation the new version takes a
pointer to the DTB as the first argument, and also swaps the order of
the number of cells and the pointer.
Change-Id: Id06b0f1ba4db1ad1f733be40e82c34f46638551a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently our fdtw_read_array() implementation requires the length of
the property to exactly match the requested size, which makes it less
flexible for parsing generic device trees.
Also the name is slightly misleading, since we treat the cells of the
array as 32 bit unsigned integers, performing the endianess conversion.
To fix those issues and align the code more with other DT users (Linux
kernel or U-Boot), rename the function to "fdt_read_uint32_array", and
relax the length check to only check if the property covers at least the
number of cells we request.
This also changes the variable names to be more in-line with other DT
users, and switches to the proper data types.
This makes this function more useful in later patches.
Change-Id: Id86f4f588ffcb5106d4476763ecdfe35a735fa6c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Move the data section to the common header.
I slightly tweaked some scripts as follows:
[1] bl1.ld.S has ALIGN(16). I added DATA_ALIGN macro, which is 1
by default, but overridden by bl1.ld.S. Currently, ALIGN(16)
of the .data section is redundant because commit 4128659076
("Fix boot failures on some builds linked with ld.lld.") padded
out the previous section to work around the issue of LLD version
<= 10.0. This will be fixed in the future release of LLVM, so
I am keeping the proper way to align LMA.
[2] bl1.ld.S and bl2_el3.ld.S define __DATA_RAM_{START,END}__ instead
of __DATA_{START,END}__. I put them out of the .data section.
[3] SORT_BY_ALIGNMENT() is missing tsp.ld.S, sp_min.ld.S, and
mediatek/mt6795/bl31.ld.S. This commit adds SORT_BY_ALIGNMENT()
for all images, so the symbol order in those three will change,
but I do not think it is a big deal.
Change-Id: I215bb23c319f045cd88e6f4e8ee2518c67f03692
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
By writing 0 to CLUSTERPWRDN DSU register bit 0, we send an
advisory to the power controller that cluster power is not required
when all cores are powered down.
The AArch32 CLUSTERPWRDN register is architecturally mapped to the
AArch64 CLUSTERPWRDN_EL1 register
Change-Id: Ie6e67c1c7d811fa25c51e2e405ca7f59bd20c81b
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
This patch adds support for GICv4 extension.
New `GIC_ENABLE_V4_EXTN` option passed to gicv3.mk makefile
was added, and enables GICv4 related changes when set to 1.
This option defaults to 0.
Change-Id: I30ebe1b7a98d3a54863900f37eda4589c707a288
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch adds code to parse memory range information passed by
coreboot, and a simple helper to test whether a specific address belongs
to a range. This may be useful for coreboot-using platforms that need to
know information about the system's memory layout (e.g. to check whether
an address passed in via SMC targets valid DRAM).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I3bea326c426db27d1a8b7d6e17418e4850e884b4
bakery_lock_normal.c uses the raw register accessor, read_sctlr(_el3)
to check whether the dcache is enabled.
Using is_dcache_enabled() is cleaner, and a good abstraction for
the library code like this.
A problem is is_dcache_enabled() is declared in the local header,
lib/xlat_tables_v2/xlat_tables_private.h
I searched for a good place to declare this helper. Moving it to
arch_helpers.h, closed to cache operation helpers, looks good enough
to me.
I also changed the type of 'is_cached' to bool for consistency,
and to avoid MISRA warnings.
Change-Id: I9b016f67bc8eade25c316aa9c0db0fa4cd375b79
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch provides support for GICv3.1 extended PPI and SPI
range. The option is enabled by setting to 1 and passing
`GIC_EXT_INTID` build flag to gicv3.mk makefile.
This option defaults to 0 with no extended range support.
Change-Id: I7d09086fe22ea531c5df51a8a1efd8928458d394
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Attempts to address MISRA compliance issues in BL1, BL2, and BL31 code.
Mainly issues like not using boolean expressions in conditionals,
conflicting variable names, ignoring return values without (void), adding
explicit casts, etc.
Change-Id: If1fa18ab621b9c374db73fa6eaa6f6e5e55c146a
Signed-off-by: John Powell <john.powell@arm.com>
* changes:
doc: brcm: Add documentation file for brcm stingray platform
drivers: Add SPI Nor flash support
drivers: Add iproc spi driver
drivers: Add emmc driver for Broadcom platforms
Add BL31 support for Broadcom stingray platform
Add BL2 support for Broadcom stingray platform
Add bl31 support common across Broadcom platforms
Add bl2 setup code common across Broadcom platforms
drivers: Add support to retrieve plat_toc_flags
Present framework restricts platform to pass desired shareability attribute
for normal memory region mapped in MMU. it defaults to inner shareability.
There are platforms where memories (like SRAM) are not placed at snoopable
region in advaned interconnect like CCN/CMN hence snoopable transaction is
not possible to these memory. Though These memories could be mapped in MMU
as MT_NON_CACHEABLE, data caches benefits won't be available.
If these memories are mapped as cacheable with non-shareable attribute,
when only one core is running like at boot time, MMU data cached could be
used for faster execution. Hence adding support to pass the shareability
attribute for memory regions.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Change-Id: I678cb50120a28dae4aa9d1896e8faf1dd5cf1754
The platform io policies array is now always accessed through a fconf getter.
This gives us an ideal spot to check for out-of-bound accesses.
Remove the assertion in plat_get_image_source(), which is now redundant.
Change-Id: Iefe808d530229073b68cbd164d927b8b6662a217
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
The chain of trust array is now always accessed through a fconf getter.
This gives us an ideal spot to check for out-of-bound accesses.
Change-Id: Ic5ea20e43cf8ca959bb7f9b60de7c0839b390add
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
* changes:
xlat_tables_v2: fix assembler warning of PLAT_RO_XLAT_TABLES
linker_script: move bss section to bl_common.ld.h
linker_script: replace common read-only data with RODATA_COMMON
linker_script: move more common code to bl_common.ld.h
Commit d5e97a1d2c ("Build: define IMAGE_AT_EL1 or IMAGE_AT_EL3
globally for C files") does not have commit 848a7e8ce1 ("Build:
introduce per-BL CPPFLAGS and ASFLAGS") as an ancestor because
they were pulled almost at the same time.
This is a follow-up conversion to be consistent with commit
11a3c5ee73 ("plat: pass -D option to BL*_CPPFLAGS instead of
BL*_CFLAGS").
With this change, the command line option, IMAGE_AT_EL3, will be
passed to .S files as well.
I remove the definition in include/lib/cpus/aarch64/cpu_macros.S
Otherwise, the following error would happen.
include/lib/cpus/aarch64/cpu_macros.S:29:0: error: "IMAGE_AT_EL3" redefined [-Werror]
Change-Id: I943c8f22356483c2ae3c57b515c69243a8fa6889
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If PLAT_RO_XLAT_TABLES is defined, the base xlat table goes to the
.rodata section instead of .bss section.
This causes a warning like:
/tmp/ccswitLr.s: Assembler messages:
/tmp/ccswitLr.s:297: Warning: setting incorrect section attributes for .rodata
It is practically no problem, but I want to keep the build log clean.
Put the base table into the "base_xlat_table" section to suppress the
assembler warnings.
The linker script determines its final destination; rodata section if
PLAT_RO_XLAT_TABLES=1, or bss section otherwise. So, the result is the
same.
Change-Id: Ic85d1d2dddd9b5339289fc2378cbcb21dd7db02e
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move the bss section to the common header. This adds BAKERY_LOCK_NORMAL
and PMF_TIMESTAMP, which previously existed only in BL31. This is not
a big deal because unused data should not be compiled in the first
place. I believe this should be controlled by BL*_SOURCES in Makefiles,
not by linker scripts.
I investigated BL1, BL2, BL2U, BL31 for plat=fvp, and BL2-AT-EL3,
BL31, BL31 for plat=uniphier. I did not see any more unexpected
code addition.
The bss section has bigger alignment. I added BSS_ALIGN for this.
Currently, SORT_BY_ALIGNMENT() is missing in sp_min.ld.S, and with this
change, the BSS symbols in SP_MIN will be sorted by the alignment.
This is not a big deal (or, even better in terms of the image size).
Change-Id: I680ee61f84067a559bac0757f9d03e73119beb33
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The common section data are repeated in many linker scripts (often
twice in each script to support SEPARATE_CODE_AND_RODATA). When you
add a new read-only data section, you end up with touching lots of
places.
After this commit, you will only need to touch bl_common.ld.h when
you add a new section to RODATA_COMMON.
Replace a series of RO section with RODATA_COMMON, which contains
6 sections, some of which did not exist before.
This is not a big deal because unneeded data should not be compiled
in the first place. I believe this should be controlled by BL*_SOURCES
in Makefiles, not by linker scripts.
When I was working on this commit, the BL1 image size increased
due to the fconf_populator. Commit c452ba159c ("fconf: exclude
fconf_dyn_cfg_getter.c from BL1_SOURCES") fixed this issue.
I investigated BL1, BL2, BL2U, BL31 for plat=fvp, and BL2-AT-EL3,
BL31, BL31 for plat=uniphier. I did not see any more unexpected
code addition.
Change-Id: I5d14d60dbe3c821765bce3ae538968ef266f1460
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These are mostly used to collect data from special structure,
and repeated in many linker scripts.
To differentiate the alignment size between aarch32/aarch64, I added
a new macro STRUCT_ALIGN.
While I moved the PMF_SVC_DESCS, I dropped #if ENABLE_PMF conditional.
As you can see in include/lib/pmf/pmf_helpers.h, PMF_REGISTER_SERVICE*
are no-op when ENABLE_PMF=0. So, pmf_svc_descs and pmf_timestamp_array
data are not populated.
Change-Id: I3f4ab7fa18f76339f1789103407ba76bda7e56d0
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch changes the prototype cm_setup_context() to use struct entry_point_info
rather than the typedef'ed version of it. This fixes the following compilation error
seen with EL3_EXCEPTION_HANDLING = 1.
<snip>
In file included from bl31/ehf.c:19:
include/lib/el3_runtime/context_mgmt.h:35:49: error: unknown type name 'entry_point_info_t'
35 | void cm_setup_context(cpu_context_t *ctx, const entry_point_info_t *ep);
| ^~~~~~~~~~~~~~~~~~
<snip>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I73b059ff2dade2259cefd0f9a097c7ea4a88055d
Add Crypto 713 support as crypto module and NVM counter provider.
As files under include/drivers/arm/cryptocell/713/ are copied verbatim
from the CryptoCell SBROM lib project they are filtered from checkpatch
coding style check.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Change-Id: I7c361772f00ca7d96481f81ac6cbb2704467e52c
Add support to retrieve plat_toc_flags value from FIP header flags.
plat_toc_flags is for platform specific use. It is stored in
FIP header by fiptool using --plat-toc-flags option.
Change-Id: Ibadd91b4f28e6503f4426e4efd404bbe512ad124
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
enable_mmu_* has a different function name, so it is not handy in the
shared code. enable_mmu() calls an appropriate one depending on the
exception level.
Change-Id: I0657968bfcb91c32733f75f9259f550a5c35b1c3
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are some cases where we want to run EL-dependent code in the
shared code.
We could use #ifdef, but it leaves slight possibility where we do not
know the exception level at the build-time (e.g. library code).
The counter approach is to use get_current_el(), but it is run-time
detection, so all EL code is linked, some of which might be unneeded.
This commit adds get_current_el_maybe_constant(). This is a static
inline function that returns a constant value if we know the exception
level at build-time. This is mostly the case.
if (get_current_el_maybe_constant() == 1) {
/* do something for EL1 */
} else if (get_current_el_maybe_constant() == 3) {
/* do something for EL3 */
}
If get_current_el_maybe_constant() is build-time constant, the compiler
will optimize out the unreachable code.
If such code is included from the library code, it is not built-time
constant. In this case, it falls back to get_current_el(), so it still
works.
Change-Id: Idb03c20342a5b5173fe2d6b40e1fac7998675ad3
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Moved SMCCC defines from plat_arm.h to new <smccc_def.h> header
and include this header in all ARM platforms.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I4cbc69c7b9307461de87b7c7bf200dd9b810e485
This patch provides support for measured boot by adding calculation
of BL2 image hash in BL1 and writing these data in TB_FW_CONFIG DTB.
Change-Id: Ic074a7ed19b14956719c271c805b35d147b7cec1
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Fixed below 'tautological-constant-compare' error when building the source
code with latest clang compiler <clang version 11.0.0>.
plat/common/plat_psci_common.c:36:2:
error: converting the result of '<<' to a boolean always evaluates
to true [-Werror,-Wtautological-constant-compare]
PMF_STORE_ENABLE)
^
include/lib/pmf/pmf.h:28:29: note: expanded from macro 'PMF_STORE_ENABLE'
PMF_STORE_ENABLE (1 << 0)
This error is observed beacuse of CASSERT placed in
"PMF_DEFINE_CAPTURE_TIMESTAMP" which do below stuff:
CASSERT(_flags, select_proper_config);
where _flags = PMF_STORE_ENABLE (1 << 0) which always results true.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ifa82ea202496a23fdf1d27ea1798d1f1b583a021
Correct the following warning given by sparse tool:
include/drivers/raw_nand.h:158:3: warning:
symbol '__packed' was not declared. Should it be static?
Change-Id: I03bd9a8aee5cdc5212ce5225be8033f1a6e92bd9
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This patch adds support to handle following TLK SMCs:
{TLK_SET_BL_VERSION, TLK_LOCK_BL_INTERFACE, TLK_BL_RPMB_SERVICE}
These SMCs need to be supported in ATF in order to forward them to
TLK. Otherwise, these functionalities won't work.
Brief:
TLK_SET_BL_VERSION: This SMC is issued by the bootloader to supply its
version to TLK. TLK can use this to prevent rollback attacks.
TLK_LOCK_BL_INTERFACE: This SMC is issued by bootloader before handing off
execution to the OS. This allows preventing sensitive SMCs being used
by the OS.
TLK_BL_RPMB_SERVICE: bootloader issues this SMC to sign or verify RPMB
frames.
Tested by: Tests TLK can receive the new SMCs issued by bootloader
Change-Id: I57c2d189a5f7a77cea26c3f8921866f2a6f0f944
Signed-off-by: Mustafa Yigit Bilgen <mbilgen@nvidia.com>
TPIDR_EL2 is missing from the EL2 state register save/restore
sequence. This patch adds it to the context save restore routines.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I35fc5ee82f97b72bcedac57c791312e7b3a45251
TLK does not participate in the system off/reset process and so
has no use for the SYSTEM_OFF/RESET notifications.
This patch removes the system off/reset handlers as a result.
Change-Id: Icf1430b1400cea88000e6d54426eb604a43cbe6c
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch enables dual execution optimized translations for EL2 and EL3
CPU exception levels.
Change-Id: I28fe98bb05687400f247e94adf44a1f3a85c38b1
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
* changes:
rpi: docs: Update maintainers file to new RPi directory scheme
rpi: console: Autodetect Mini-UART vs. PL011 configuration
rpi3: build: Include GPIO driver in all BL stages
rpi: Allow using PL011 UART for RPi3/RPi4
rpi3: console: Use same "clock-less" setup scheme as RPi4
rpi3: gpio: Simplify GPIO setup
There is really no reason to use and pass around a struct when its only
member is the (fixed) base address.
Remove the struct and just use the base address on its own inside the
GPIO driver. Then set the base address automatically.
This simplifies GPIO setup for users, which now don't need to deal with
zeroing a struct and setting the base address anymore.
Change-Id: I3060f7859e3f8ef9a24cc8fb38307b5da943f127
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Implemented SMCCC_ARCH_SOC_ID call in order to get below
SOC information:
1. SOC revision
2. SOC version
Implementation done using below SMCCC specification document:
https://developer.arm.com/docs/den0028/c
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ie0595f1c345a6429a6fb4a7f05534a0ca9c9a48b
This patch introduces the `SPCI_ID_GET` interface which will return the
ID of the calling SPCI component. Returns 0 for requests from the
non-secure world and the SPCI component ID as specified in the manifest
for secure world requests.
Change-Id: Icf81eb1d0e1d7d5c521571e04972b6e2d356e0d1
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Signed-off-by: Marc Bonnici <marc.bonnici@arm.com>
This patch adds an interrupt handler for TLK. On receiving an
interrupt, the source of the interrupt is determined and the
interrupt is marked complete. The IRQ number is passed to
TLK along with a special SMC function ID. TLK issues an SMC
to notify completion of the interrupt handler in the S-EL1
world.
Change-Id: I76f28cee6537245c5e448d2078f86312219cea1a
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Necessary infrastructure added to integrate fconf framework in BL31 & SP_MIN.
Created few populator() functions which parse HW_CONFIG device tree
and registered them with fconf framework. Many of the changes are
only applicable for fvp platform.
This patch:
1. Adds necessary symbols and sections in BL31, SP_MIN linker script
2. Adds necessary memory map entry for translation in BL31, SP_MIN
3. Creates an abstraction layer for hardware configuration based on
fconf framework
4. Adds necessary changes to build flow (makefiles)
5. Minimal callback to read hw_config dtb for capturing properties
related to GIC(interrupt-controller node)
6. updates the fconf documentation
Change-Id: Ib6292071f674ef093962b9e8ba0d322b7bf919af
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
A populate() function essentially captures the value of a property,
defined by a platform, into a fconf related c structure. Such a
callback is usually platform specific and is associated to a specific
configuration source.
For example, a populate() function which captures the hardware topology
of the platform can only parse HW_CONFIG DTB. Hence each populator
function must be registered with a specific 'config_type' identifier.
It broadly represents a logical grouping of configuration properties
which is usually a device tree source file.
Example:
> TB_FW: properties related to trusted firmware such as IO policies,
base address of other DTBs, mbedtls heap info etc.
> HW_CONFIG: properties related to hardware configuration of the SoC
such as topology, GIC controller, PSCI hooks, CPU ID etc.
This patch modifies FCONF_REGISTER_POPULATOR macro and fconf_populate()
to register and invoke the appropriate callbacks selectively based on
configuration type.
Change-Id: I6f63b1fd7a8729c6c9137d5b63270af1857bb44a
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
* changes:
Factor xlat_table sections in linker scripts out into a header file
xlat_tables_v2: use ARRAY_SIZE in REGISTER_XLAT_CONTEXT_FULL_SPEC
xlat_tables_v2: merge REGISTER_XLAT_CONTEXT_{FULL_SPEC,RO_BASE_TABLE}
TF-A has so many linker scripts, at least one linker script for each BL
image, and some platforms have their own ones. They duplicate quite
similar code (and comments).
When we add some changes to linker scripts, we end up with touching
so many files. This is not nice in the maintainability perspective.
When you look at Linux kernel, the common code is macrofied in
include/asm-generic/vmlinux.lds.h, which is included from each arch
linker script, arch/*/kernel/vmlinux.lds.S
TF-A can follow this approach. Let's factor out the common code into
include/common/bl_common.ld.h
As a start point, this commit factors out the xlat_table section.
Change-Id: Ifa369e9b48e8e12702535d721cc2a16d12397895
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With this, it is clearer that .base_table_entries and .tables_num
are the array size of .base_table and .tables, respectively.
Change-Id: I634e65aba835ab9908cc3919355df6bc6e18d42a
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
xlat_tables_v2_helpers.h defines two quite similar macros,
REGISTER_XLAT_CONTEXT_FULL_SPEC and REGISTER_XLAT_CONTEXT_RO_BASE_TABLE.
Only the difference is the section of _ctx_name##_base_xlat_table.
Parameterize it and unify these two macros.
The base xlat table goes into the .bss section by default.
If PLAT_RO_XLAT_TABLES is defined, it goes into the .rodata section.
Change-Id: I8b02f4da98f0c272e348a200cebd89f479099c55
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* changes:
plat/arm: Pass cookie argument down to arm_get_rotpk_info()
plat/arm: Add support for dualroot CoT
plat/arm: Provide some PROTK files for development
This patch provides separation of GICD, GICR accessor
functions and adds new macros for GICv3 registers access
as a preparation for GICv3.1 and GICv4 support.
NOTE: Platforms need to modify to include both
'gicdv3_helpers.c' and 'gicrv3_helpers.c' instead of the
single helper file previously.
Change-Id: I1641bd6d217d6eb7d1228be3c4177b2d556da60a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
This patch provides a fix for incorrect crash dump data for
lower EL when TF-A is built with HANDLE_EA_EL3_FIRST=1 option
which enables routing of External Aborts and SErrors to EL3.
Change-Id: I9d5e6775e6aad21db5b78362da6c3a3d897df977
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
TBBR spec advocates for optional encryption of firmwares (see optional
requirement: R060_TBBR_FUNCTION). So add an IO abstaction layer to
support firmware decryption that can be stacked above any underlying IO/
packaging layer like FIP etc. It aims to provide a framework to load any
encrypted IO payload.
Also, add plat_get_enc_key_info() to be implemented in a platform
specific manner as handling of encryption key may vary from one platform
to another.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Change-Id: I9892e0ddf00ebecb8981301dbfa41ea23e078b03
Add framework for autheticated decryption of data. Currently this
patch optionally imports mbedtls library as a backend if build option
"DECRYPTION_SUPPORT = aes_gcm" is set to perform authenticated decryption
using AES-GCM algorithm.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Change-Id: I2966f0e79033151012bf4ffc66f484cd949e7271
This patch implements loading of Secure Partition packages using
existing framework of loading other bl images.
The current framework uses a statically defined array to store all the
possible image types and at run time generates a link list and traverse
through it to load different images.
To load SPs, a new array of fixed size is introduced which will be
dynamically populated based on number of SPs available in the system
and it will be appended to the loadable images list.
Change-Id: I8309f63595f2a71b28a73b922d20ccba9c4f6ae4
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Added SPMD_SPM_AT_SEL2 build command line parameter.
Set to 1 to run SPM at S-EL2.
Set to 0 to run SPM at S-EL1 (pre-v8.4 or S-EL2 is disabled).
Removed runtime EL from SPM core manifest.
Change-Id: Icb4f5ea4c800f266880db1d410d63fe27a1171c0
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
This patch adds EL2 registers that are supported up to ARMv8.6.
ARM_ARCH_MINOR has to specified to enable save/restore routine.
Note: Following registers are still not covered in save/restore.
* AMEVCNTVOFF0<n>_EL2
* AMEVCNTVOFF1<n>_EL2
* ICH_AP0R<n>_EL2
* ICH_AP1R<n>_EL2
* ICH_LR<n>_EL2
Change-Id: I4813f3243e56e21cb297b31ef549a4b38d4876e1
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
Use the firmware configuration framework to retrieve information about
Secure Partitions to facilitate loading them into memory.
To load a SP image we need UUID look-up into FIP and the load address
where it needs to be loaded in memory.
This patch introduces a SP populator function which gets UUID and load
address from firmware config device tree and updates its C data
structure.
Change-Id: I17faec41803df9a76712dcc8b67cadb1c9daf8cd
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
NOTE: Not all EL-2 system registers are saved/restored.
This subset includes registers recognized by ARMv8.0
Change-Id: I9993c7d78d8f5f8e72d1c6c8d6fd871283aa3ce0
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
aarch32 CPUs speculatively execute instructions following a
ERET as if it was not a jump instruction. This could lead to
cache-based side channel vulnerabilities. The software fix is
to place barrier instructions following ERET.
The counterpart patch for aarch64 is merged:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=f461fe346b728d0e88142fd7b8f2816415af18bc
Change-Id: I2aa3105bee0b92238f389830b3a3b8650f33af3d
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
* changes:
board/rddaniel: intialize tzc400 controllers
plat/arm/tzc: add support to configure multiple tzc400
plat/arm: allow boards to specify second DRAM Base address
plat/arm: allow boards to define PLAT_ARM_TZC_FILTERS
MISRA C-2012 Rule 20.7:
Macro parameter expands into an expression without being wrapped by parentheses.
MISRA C-2012 Rule 12.1:
Missing explicit parentheses on sub-expression.
MISRA C-2012 Rule 18.4:
Essential type of the left hand operand is not the same as that of the right
operand.
Include does not provide any needed symbols.
Change-Id: Ie1c6451cfbc8f519146c28b2cf15c50b1f36adc8
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
* changes:
marvell: Consolidate console register calls
uniphier: Use generic console_t data structure
spe: Use generic console_t data structure
LS 16550: Use generic console_t data structure
stm32: Use generic console_t data structure
rcar: Use generic console_t data structure
a3700: Use generic console_t data structure
16550: Use generic console_t data structure
imx: Use generic console_t data structure
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location for the coreboot memory console.
This removes the base member from the coreboot specific data structure,
but keeps the struct console_cbmc_t and its size member.
Change-Id: I7f1dffd41392ba3fe5c07090aea761a42313fb5b
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I7a23327394d142af4b293ea7ccd90b843c54587c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I07a07677153d3671ced776671e4f107824d3df16
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
*All* UART drivers in TF-A are storing their base address as a uintptr_t
pointer in the first location of the UART specific driver data.
Since the base address is a pretty natural and generic data item, we
should integrate this into the generic console_t structure.
That will not only allow to remove a lot of seemingly UART specific data
structures, but also enables to simplify runtime choices between different
UARTs, since they can share the same pointer.
This patch just adds the new member, the existing data structures will
be handled on a per-UART base in follow-up patches.
Change-Id: I59ce49471ccc8f3b870f2cfd8a72ebfd0cb14d12
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I9f8b55414ab7965e431e3e86d182eabd511f32a4
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: Iea6ca26ff4903c33f0fad27fec96fdbabd4e0a91
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I836e26ff1771abf21fd460d0ee40e90a452e9b43
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I89c3ab2ed85ab941d8b38ced48474feb4aaa8b7e
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: I5c2fe3b6a667acf80c808cfec4a64059a2c9c25f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch introduces a build flag which allows the xlat tables
to be mapped in a read-only region within BL31 memory. It makes it
much harder for someone who has acquired the ability to write to
arbitrary secure memory addresses to gain control of the
translation tables.
The memory attributes of the descriptors describing the tables
themselves are changed to read-only secure data. This change
happens at the end of BL31 runtime setup. Until this point, the
tables have read-write permissions. This gives a window of
opportunity for changes to be made to the tables with the MMU on
(e.g. reclaiming init code). No changes can be made to the tables
with the MMU turned on from this point onwards. This change is also
enabled for sp_min and tspd.
To make all this possible, the base table was moved to .rodata. The
penalty we pay is that now .rodata must be aligned to the size of
the base table (512B alignment). Still, this is better than putting
the base table with the higher level tables in the xlat_table
section, as that would cost us a full 4KB page.
Changing the tables from read-write to read-only cannot be done with
the MMU on, as the break-before-make sequence would invalidate the
descriptor which resolves the level 3 page table where that very
descriptor is located. This would make the translation required for
writing the changes impossible, generating an MMU fault.
The caches are also flushed.
Signed-off-by: Petre-Ionut Tudor <petre-ionut.tudor@arm.com>
Change-Id: Ibe5de307e6dc94c67d6186139ac3973516430466
The cookie will be leveraged in the next commit.
Change-Id: Ie8bad275d856d84c27466461cf815529dd860446
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
This new chain of trust defines 2 independent signing domains:
1) One for the silicon firmware (BL1, BL2, BL31) and optionally the
Trusted OS. It is rooted in the Silicon ROTPK, just as in the TBBR
CoT.
2) One for the Normal World Bootloader (BL33). It is rooted in a new key
called Platform ROTPK, or PROTPK for short.
In terms of certificates chain,
- Signing domain 1) is similar to what TBBR advocates (see page 21 of
the TBBR specification), except that the Non-Trusted World Public Key
has been removed from the Trusted Key Certificate.
- Signing domain 2) only contains the Non-Trusted World Content
certificate, which provides the hash of the Non-Trusted World
Bootloader. Compared to the TBBR CoT, there's no Non-Trusted World
Key certificate for simplicity.
Change-Id: I62f1e952522d84470acc360cf5ee63e4c4b0b4d9
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
At each BL entry point, the registers r9 to r12 are used to save info from
the previous BL parameters put in r0 to r3. But zeromem uses r12, leading
to a corruption of arg3. Therefore this change copies r12 to r7 before
zeromem() call and restores r12 afterwards. It may be better to save it
in r7 in el3_arch_init_common and not at the entrypoint as r7 could be used
in other functions, especially platform ones.
This is a fix for Task T661.
Change-Id: Icc11990c69b5d4c542d08aca1a77b1f754b61a53
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This patch modifies the delay timer driver to switch to the ARM
secure physical timer instead of using Tegra's on-chip uS timer.
The secure timer is not accessible to the NS world and so eliminates
an important attack vector, where the Tegra timer source gets switched
off from the NS world leading to a DoS attack for the trusted world.
This timer is shared with the S-EL1 layer for now, but later patches
will mark it as exclusive to the EL3 exception mode.
Change-Id: I2c00f8cb4c48b25578971c626c314603906ad7cc
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch moves the MHZ_TICKS_PER_SEC macro to utils_def.h
for other platforms to use.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I6c4dc733f548d73cfdb3515ec9ad89a9efaf4407
The CPUACTLR_EL1 register on Cortex-A57 CPUs supports a bit to enable
non-cacheable streaming enhancement. Platforms can set this bit only
if their memory system meets the requirement that cache line fill
requests from the Cortex-A57 processor are atomic.
This patch adds support to enable higher performance non-cacheable load
forwarding for such platforms. Platforms must enable this support by
setting the 'A57_ENABLE_NONCACHEABLE_LOAD_FWD' flag from their
makefiles. This flag is disabled by default.
Change-Id: Ib27e55dd68d11a50962c0bbc5b89072208b4bac5
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Removed duplicate error code present for SMCCC and used
proper error code for "SMCCC_ARCH_WORKAROUND_2" call.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I76fc7c88095f78a7e2c3d205838f8eaf3132ed5c
For platforms that have two or more TZC400 controllers instantiated,
allow the TZC400 driver to be usable with all those instances.
This is achieved by allowing 'arm_tzc400_setup' function to accept
the base address of the TZC400 controller.
Change-Id: I4add470e6ddb58432cd066145e644112400ab924
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
The base address for second DRAM varies across different platforms.
So allow platforms to define second DRAM by moving Juno/SGM-775 specific
definition of second DRAM base address to Juno/SGM-775 board definition
respectively, SGI/RD specific definition of DRAM 2 base address to SGI
board definition.
Change-Id: I0ecd3a2bd600b6c7019c7f06f8c452952bd07cae
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
A TZC400 can have upto 4 filters and the number of filters instantiated
within a TZC400 is platform dependent. So allow platforms to define the
value of PLAT_ARM_TZC_FILTERS by moving the existing Juno specific
definition of PLAT_ARM_TZC_FILTERS to Juno board definitions.
Change-Id: I67a63d7336595bbfdce3163f9a9473e15e266f40
Signed-off-by: Suyash Pathak <suyash.pathak@arm.com>
Fixes for the following MISRA violations:
- Missing explicit parentheses on sub-expression
- An identifier or macro name beginning with an
underscore, shall not be declared
- Type mismatch in BL1 SMC handlers and tspd_main.c
Change-Id: I7a92abf260da95acb0846b27c2997b59b059efc4
Signed-off-by: Zelalem <zelalem.aweke@arm.com>
* changes:
SPMD: enable SPM dispatcher support
SPMD: hook SPMD into standard services framework
SPMD: add SPM dispatcher based upon SPCI Beta 0 spec
SPMD: add support to run BL32 in TDRAM and BL31 in secure DRAM on Arm FVP
SPMD: add support for an example SPM core manifest
SPMD: add SPCI Beta 0 specification header file
This patch adds a rudimentary SPM dispatcher component in EL3.
It does the following:
- Consumes the TOS_FW_CONFIG to determine properties of the SPM core
component
- Initialises the SPM core component which resides in the BL32 image
- Implements a handler for SPCI calls from either security state. Some
basic validation is done for each call but in most cases it is simply
forwarded as-is to the "other" security state.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I7d116814557f7255f4f4ebb797d1619d4fbab590
This patch reserves and maps the Trusted DRAM for SPM core execution.
It also configures the TrustZone address space controller to run BL31
in secure DRAM.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: I7e1bb3bbc61a0fec6a9cb595964ff553620c21dc
This patch repurposes the TOS FW configuration file as the manifest for
the SPM core component which will reside at the secure EL adjacent to
EL3. The SPM dispatcher component will use the manifest to determine how
the core component must be initialised. Routines and data structure to
parse the manifest have also been added.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: Id94f8ece43b4e05609f0a1d364708a912f6203cb
Currently sptool generates a single blob containing all the Secure
Partitions, with latest SPM implementation, it is desirable to have
individual blobs for each Secure Partition. It allows to leverage
packaging and parsing of SP on existing FIP framework. It also allows
SP packages coming from different sources.
This patch modifies sptool so that it takes number of SP payload pairs
as input and generates number of SP blobs instead of a single blob.
Each SP blob can optionally have its own header containing offsets and
sizes of different payloads along with a SP magic number and version.
It is also associated in FIP with a UUID, provided by SP owner.
Usage example:
sptool -i sp1.bin:sp1.dtb -o sp1.pkg -i sp2.bin:sp2.dtb -o sp2.pkg ...
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ie2db8e601fa1d4182d0a1d22e78e9533dce231bc
At the moment, address demangling is only used by the backtrace
functionality. However, at some point, other parts of the TF-A
codebase may want to use it.
The 'demangle_address' function is replaced with a single XPACI
instruction which is also added in 'do_crash_reporting()'.
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Change-Id: I4424dcd54d5bf0a5f9b2a0a84c4e565eec7329ec
On systems that have multiple platform components that can interpret the
SCMI messages, there is a need to support multiple SCMI channels (one
each to those platform components). Extend the existing SCMI interface
that currently supports only a single SCMI channel to support multiple
SCMI channels.
Change-Id: Ice4062475b903aef3b5e5bc37df364c9778a62c5
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
In order to allow the MHUv2 driver to be usable with multiple MHUv2
controllers, use the base address of the controller from the platform
information instead of the MHUV2_BASE_ADDR macro.
Change-Id: I4dbab87b929fb0568935e6c8b339ce67937f8cd1
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Multi-chip platforms have two or more identical chips connected using a
high speed coherent link. In order to identify such platforms,
add chip_id and multi_chip_mode information in the platform variant
info structure. The values of these two new elements is populated
during boot.
Change-Id: Ie6e89cb33b3f0f408814f6239cd06647053e23ed
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Currently, an IO setup failure will be ignored on arm platform release
build. Change this to panic instead.
Change-Id: I027a045bce2422b0a0fc4ff9e9d4c6e7bf5d2f98
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change the return type of "arm_io_is_toc_valid()" and
"plat_arm_bl1_fwu_needed()" to bool, to match function behavior.
Change-Id: I503fba211219a241cb263149ef36ca14e3362a1c
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Use the firmware configuration framework to store the io_policies
information inside the configuration device tree instead of the static
structure in the code base.
The io_policies required by BL1 can't be inside the dtb, as this one is
loaded by BL1, and only available at BL2.
This change currently only applies to FVP platform.
Change-Id: Ic9c1ac3931a4a136aa36f7f58f66d3764c1bfca1
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Use the firmware configuration framework in arm dynamic configuration
to retrieve mbedtls heap information between bl1 and bl2.
For this, a new fconf getter is added to expose the device tree base
address and size.
Change-Id: Ifa5ac9366ae100e2cdd1f4c8e85fc591b170f4b6
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Use fconf to retrieve the `disable_authentication` property.
Move this access from arm dynamic configuration to bl common.
Change-Id: Ibf184a5c6245d04839222f5457cf5e651f252b86
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
This patch introduces a better separation between the trusted-boot
related properties, and the dynamic configuration DTBs loading
information.
The dynamic configuration DTBs properties are moved to a new node:
`dtb-registry`. All the sub-nodes present will be provided to the
dynamic config framework to be loaded. The node currently only contains
the already defined configuration DTBs, but can be extended for future
features if necessary.
The dynamic config framework is modified to use the abstraction provided
by the fconf framework, instead of directly accessing the DTBs.
The trusted-boot properties are kept under the "arm,tb_fw" compatible
string, but in a separate `tb_fw-config` node.
The `tb_fw-config` property of the `dtb-registry` node simply points
to the load address of `fw_config`, as the `tb_fw-config` is currently
part of the same DTB.
Change-Id: Iceb6c4c2cb92b692b6e28dbdc9fb060f1c46de82
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Use the dtb provided by bl1 as configuration file for fconf.
Change-Id: I3f466ad9b7047e1a361d94e71ac6d693e31496d9
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Move the loading of the dtb from arm_dym_cfg to fconf. The new loading
function is not associated to arm platform anymore, and can be moved
to bl_main if wanted.
Change-Id: I847d07eaba36d31d9d3ed9eba8e58666ea1ba563
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Introduce the Firmware CONfiguration Framework (fconf).
The fconf is an abstraction layer for platform specific data, allowing
a "property" to be queried and a value retrieved without the requesting
entity knowing what backing store is being used to hold the data.
The default backing store used is C structure. If another backing store
has to be used, the platform integrator needs to provide a "populate()"
function to fill the corresponding C structure.
The "populate()" function must be registered to the fconf framework with
the "FCONF_REGISTER_POPULATOR()". This ensures that the function would
be called inside the "fconf_populate()" function.
A two level macro is used as getter:
- the first macro takes 3 parameters and converts it to a function
call: FCONF_GET_PROPERTY(a,b,c) -> a__b_getter(c).
- the second level defines a__b_getter(c) to the matching C structure,
variable, array, function, etc..
Ex: Get a Chain of trust property:
1) FCONF_GET_PROPERY(tbbr, cot, BL2_id) -> tbbr__cot_getter(BL2_id)
2) tbbr__cot_getter(BL2_id) -> cot_desc_ptr[BL2_id]
Change-Id: Id394001353ed295bc680c3f543af0cf8da549469
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Enables usage of ARM_ROTPK_LOCATION=regs for FVP board.
Removes hard-coded developer keys. Instead, setting
ARM_ROTPK_LOCATION=devel_* takes keys from default directory.
In case of ROT_KEY specified - generates a new hash and replaces the
original.
Note: Juno board was tested by original feature author and was not tested
for this patch since we don't have access to the private key. Juno
implementation was moved to board-specific file without changing
functionality. It is not known whether byte-swapping is still needed
for this platform.
Change-Id: I0fdbaca0415cdcd78f3a388551c2e478c01ed986
Signed-off-by: Max Shvetsov <maksims.svecovs@arm.com>
This patch adds a header file with defines based on the SPCI Beta 0 spec.
It will be used by the SPM dispatcher component which will be introduced
in subsequent patches.
Signed-off-by: Achin Gupta <achin.gupta@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
Change-Id: Ia8a196cd85ebc14731f24801698d0a49a97b6063
This patch adds 'fdtw_read_bytes' and 'fdtw_write_inplace_bytes'
functions for read/write array of bytes from/to a given property.
It also adds 'fdt_setprop_inplace_namelen_partial' to jmptbl.i
files for builds with USE_ROMLIB=1 option.
Change-Id: Ied7b5c8b38a0e21d508aa7bcf5893e656028b14d
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
In order to access MG SRAM, the amb bridge needs to be configured which is
done in bl2 platform init.
For MG CM3, the image is only loaded to its SRAM and the CM3 itself is
left in reset. It is because the next stage bootloader (e.g. u-boot)
will trigger action which will take it out of reset when needed. This
can happen e.g. when appropriate device-tree setup (which has enabled
802.3 auto-neg) will be chosen. In other cases the MG CM3 should not be
running.
Change-Id: I816ea14e3a7174eace068ec44e3cc09998d0337e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
This patch adds 'calc_hash' function using Mbed TLS library
required for Measured Boot support.
Change-Id: Ifc5aee0162d04db58ec6391e0726a526f29a52bb
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
The Secure Configuration Register is 64-bits in AArch64 and 32-bits in
AArch32. Use u_register_t instead of unsigned int to reflect this.
Change-Id: I51b69467baba36bf0cfaec2595dc8837b1566934
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
In order to support SEPARATE_NOBITS_REGION for Arm platforms, we need to load
BL31 PROGBITS into secure DRAM space and BL31 NOBITS into SRAM. Hence mandate
the build to require that ARM_BL31_IN_DRAM is enabled as well.
Naturally with SEPARATE_NOBITS_REGION enabled, the BL31 initialization code
cannot be reclaimed to be used for runtime data such as secondary cpu stacks.
Memory map for BL31 NOBITS region also has to be created.
Change-Id: Ibbc8c9499a32e63fd0957a6e254608fbf6fa90c9
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
CPUECTLR_EL1.EXTLLC bit indicates the presense of internal or external
last level cache(LLC) in the system, the reset value is internal LLC.
To cater for the platforms(like N1SDP) which has external LLC present
introduce a new build option 'NEOVERSE_N1_EXTERNAL_LLC' which can be
enabled by platform port.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ibf475fcd6fd44401897a71600f4eafe989921363
Currently, the end address macros are defined per BL, like BL2_END,
BL31_END, BL32_END. They are not handy in the common code shared
between multiple BL stages.
This commit introduces BL_END, which is equivalent to BL{2,31,32}_END,
and will be useful for the BL-common code.
Change-Id: I3c39bf6096d99ce920a5b9fa21c0f65456fbfe8a
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This makes the PSCI SYSTEM_OFF call work on QEMU. It assumes that QEMU has
semihosting enabled, but that is already assumed by the image loader.
Signed-off-by: Andrew Walbran <qwandor@google.com>
Change-Id: I0fb7cf7909262b675c3143efeac07f4d60730b03
Even though ERET always causes a jump to another address, aarch64 CPUs
speculatively execute following instructions as if the ERET
instruction was not a jump instruction.
The speculative execution does not cross privilege-levels (to the jump
target as one would expect), but it continues on the kernel privilege
level as if the ERET instruction did not change the control flow -
thus execution anything that is accidentally linked after the ERET
instruction. Later, the results of this speculative execution are
always architecturally discarded, however they can leak data using
microarchitectural side channels. This speculative execution is very
reliable (seems to be unconditional) and it manages to complete even
relatively performance-heavy operations (e.g. multiple dependent
fetches from uncached memory).
This was fixed in Linux, FreeBSD, OpenBSD and Optee OS:
679db7080129fb48ace43a08873eceabfd092aa1
It is demonstrated in a SafeSide example:
https://github.com/google/safeside/blob/master/demos/eret_hvc_smc_wrapper.cchttps://github.com/google/safeside/blob/master/kernel_modules/kmod_eret_hvc_smc/eret_hvc_smc_module.c
Signed-off-by: Anthony Steinhauser <asteinhauser@google.com>
Change-Id: Iead39b0b9fb4b8d8b5609daaa8be81497ba63a0f
Device size could be more than 4GB, we must
define size as unsigned long long.
Change-Id: I52055cf5c1c15ff18ab9e157aa9b73c8b4fb7b63
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Add the standard CLAMP macro. It ensures that
x is between the limits set by low and high.
If low is greater than high the result is undefined.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Change-Id: Ia173bb9ca51bc8d9a8ec573bbc15636a94f881f4
SPI-NOR framework is based on SPI-MEM framework using
spi_mem_op execution interface.
It implements read functions and allows NOR configuration
up to quad mode.
Default management is 1 data line but it can be overridden
by platform.
It also includes specific quad mode configuration for
Spansion, Micron and Macronix memories.
Change-Id: If49502b899b4a75f6ebc3190f6bde1013651197f
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
This framework supports SPI-NAND and is based on the
SPI-MEM framework for SPI operations. It uses a common high
level access using the io_mtd.
It is limited to the read functionalities.
Default behavior is the basic one data line operation
but it could be overridden by platform.
Change-Id: Icb4e0887c4003a826f47c876479dd004a323a32b
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
The raw NAND framework supports SLC NAND devices.
It introduces a new high level interface (io_mtd) that
defines operations a driver can register to the NAND framework.
This interface will fill in the io_mtd device specification:
- device_size
- erase_size
that could be used by the io_storage interface.
NAND core source file integrates the standard read loop that
performs NAND device read operations using a skip bad block strategy.
A platform buffer must be defined in case of unaligned
data. This buffer must fit to the maximum device page size
defined by PLATFORM_MTD_MAX_PAGE_SIZE.
The raw_nand.c source file embeds the specific NAND operations
to read data.
The read command is a raw page read without any ECC correction.
This can be overridden by a low level driver.
No generic support for write or erase command or software
ECC correction.
NAND ONFI detection is available and can be enabled using
NAND_ONFI_DETECT=1.
For non-ONFI NAND management, platform can define required
information.
Change-Id: Id80e9864456cf47f02b74938cf25d99261da8e82
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Implements a way to add platform specific power off code to a
Marvell Armada 8K platform.
Marvell Armada 8K boards can now add a board/system_power.c file
that contains a system_power_off() function.
This function can now send a command to a power management MCU or
other board periferals before shutting the board down.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Change-Id: Iaba20bc2f603195679c54ad12c0c18962dd8e3db
---
I am working on a device that will be ported later, which has a
custom power management MCU that handles LEDs, board power and fans
and requires this separation.
IO seek offset can be set to values above UINT32_MAX, this change
changes the seek offset argument from 'ssize_t' to 'signed long long'.
Fixing platform seek functions to match the new interface update.
Change-Id: I25de83b3b7abe5f52a7b0fee36f71e60cac9cfcb
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
NOTE for platform integrators:
API `plat_psci_stat_get_residency()` third argument
`last_cpu_idx` is changed from "signed int" to the
"unsigned int" type.
Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.
2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent
Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.
Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c
In further patches, we aim to enable -Wredundant-decls by default.
This rearragement of helper macros is necessary to make Coverity
tool happy as well as making sure there are no redundant function
declarations for PMF related declarations.
Also, PMF related macros were added to provide appropriate function
declarations for helper APIs which capture PSCI statistics.
Change-Id: I36273032dde8fa079ef71235ed3a4629c5bfd981
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
The SCU connects one to four Cortex-A5/Cortex-A9 processors
to the memory system through the AXI interfaces.
The SCU functions are to:
- maintain data cache coherency between the Cortex-A5/Cortex-A9
processors
- initiate L2 AXI memory accesses
- arbitrate between Cortex-A5/Cortex-A9 processors requesting
L2 accesses
- manage ACP accesses.
Snoop Control Unit will enable to snoop on other CPUs caches.
This is very important when it comes to synchronizing data between
CPUs. As an example, there is a high chance that data might be
cache'd and other CPUs can't see the change. In such cases,
if snoop control unit is enabled, data is synchoronized immediately
between CPUs and the changes are visible to other CPUs.
This driver provides functionality to enable SCU as well as enabling
user to know the following
- number of CPUs present
- is a particular CPU operating in SMP mode or AMP mode
- data cache size of a particular CPU
- does SCU has ACP port
- is L2CPRESENT
Change-Id: I0d977970154fa60df57caf449200d471f02312a0
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
On some platforms the UART might have already been initialised, for
instance by firmware running before TF-A or by a separate management
processor. In this case it would not be need to initialise it again
(doing so could create spurious characters). But more importantly this
saves us from knowing the right baudrate and the right base clock rate
for the UART. This can lead to more robust and versatile firmware builds.
Allow to skip the 16550 UART initialisation and baud rate divisor
programming, by interpreting an input clock rate of "0" to signify this
case. This will just skip the call to console_16550_core_init, but still
will register the console properly.
Users should just pass 0 as the second parameter, the baudrate (third
parameter) will then be ignored as well.
Fix copy & paste typos in comments for the console_16550_register()
function on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Change-Id: I9f8fca5b358f878fac0f31dc411358fd160786ee
Some platforms are extremely memory constrained and must split BL31
between multiple non-contiguous areas in SRAM. Allow the NOBITS
sections (.bss, stacks, page tables, and coherent memory) to be placed
in a separate region of RAM from the loaded firmware image.
Because the NOBITS region may be at a lower address than the rest of
BL31, __RW_{START,END}__ and __BL31_{START,END}__ cannot include this
region, or el3_entrypoint_common would attempt to invalidate the dcache
for the entire address space. New symbols __NOBITS_{START,END}__ are
added when SEPARATE_NOBITS_REGION is enabled, and the dcached for the
NOBITS region is invalidated separately.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Idedfec5e4dbee77e94f2fdd356e6ae6f4dc79d37
Erratum 1688305 is a Cat B erratum present in r0p0, r0p1 versions
of Hercules core. The erratum can be avoided by setting bit 1 of the
implementation defined register CPUACTLR2_EL1 to 1 to prevent store-
release from being dispatched before it is the oldest.
Change-Id: I2ac04f5d9423868b6cdd4ceb3d0ffa46e570efed
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Add additional field definitions for
Cortex_A72 L2 Control registers
Change-Id: I5ef3a6db41cd7c5d9904172720682716276b7889
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
The contents of this header have been merged into the spm_mm_svc.h
header file.
Change-Id: I01530b2e4ec1b4c091ce339758025e2216e740a4
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Before adding any new SPM-related components we should first do
some cleanup around the existing SPM-MM implementation. The aim
is to make sure that any SPM-MM components have names that clearly
indicate that they are MM-related. Otherwise, when adding new SPM
code, it could quickly become confusing as it would be unclear to
which component the code belongs.
The secure_partition.h header is a clear example of this, as the
name is generic so it could easily apply to any SPM-related code,
when it is in fact SPM-MM specific.
This patch renames the file and the two structures defined within
it, and then modifies any references in files that use the header.
Change-Id: I44bd95fab774c358178b3e81262a16da500fda26
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
The Secure Partition Manager (SPM) prototype implementation is
being removed. This is preparatory work for putting in place a
dispatcher component that, in turn, enables partition managers
at S-EL2 / S-EL1.
This patch removes:
- The core service files (std_svc/spm)
- The Resource Descriptor headers (include/services)
- SPRT protocol support and service definitions
- SPCI protocol support and service definitions
Change-Id: Iaade6f6422eaf9a71187b1e2a4dffd7fb8766426
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Signed-off-by: Artsem Artsemenka <artsem.artsemenka@arm.com>
There are two different implementations of Secure Partition
management in TF-A. One is based on the "Management Mode" (MM)
design, the other is based on the Secure Partition Client Interface
(SPCI) specification. Currently there is a dependency between their
build flags that shouldn't exist, making further development
harder than it should be. This patch removes that
dependency, making the two flags function independently.
Before: ENABLE_SPM=1 is required for using either implementation.
By default, the SPCI-based implementation is enabled and
this is overridden if SPM_MM=1.
After: ENABLE_SPM=1 enables the SPCI-based implementation.
SPM_MM=1 enables the MM-based implementation.
The two build flags are mutually exclusive.
Note that the name of the ENABLE_SPM flag remains a bit
ambiguous - this will be improved in a subsequent patch. For this
patch the intention was to leave the name as-is so that it is
easier to track the changes that were made.
Change-Id: I8e64ee545d811c7000f27e8dc8ebb977d670608a
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
Provide an SMC interface to the 9p filesystem. This permits
accessing firmware drivers through a common interface, using
standardized read/write/control operations.
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I9314662314bb060f6bc02714476574da158b2a7d
Konstantin Porotchkin
Madhukar Pappireddy
Nicola Mazzucato
Leif Lindholm
Olivier Deprez
Max Shvetsov
Venkatesh Yadav Abbarapu
Bipin Ravi
Sandrine Bailleux
Bharat Gooty
johpow01
Pankaj Gupta
Kuldeep Singh
Yann Gautier
Tomas Pilar
Chris Kay
Usama Arif
Manish Pandey
Andre Przywara
Heyi Guo
Jimmy Brisson
Peng Fan
Pali Rohár
Michal Simek
Arunachalam Ganapathy
Samuel Holland
Javier Almansa Sobrino
Alexei Fedorov
David Horstmann
Joanna Farley
Saurabh Gorecha
Mark Dykes
Manish V Badarkhe
Lauren Wehrmeister
Jagadeesh Ujja
Manoj Kumar
Lionel Debieve
Sandeep Tripathy
Pramod Kumar
Hemant Nigam
Varun Wadekar
Stefan Chulski
Alex Van Brunt
Ben Peled
Etienne Carriere
Masahiro Yamada
Louis Mayencourt
J-Alves
Sheetal Tigadoli
Marcin Wojtas
Etienne Carriere
David Pu
Alex Leibovich
Grzegorz Jaszczyk
Masahisa Kojima
Balint Dobszay
Julius Werner
Gilad Ben-Yossef
Scott Branden
Mustafa Yigit Bilgen
Kalyani Chidambaram
Sumit Garg
Petre-Ionut Tudor
Suyash Pathak
Zelalem
Achin Gupta
Aditya Angadi
Vijayenthiran Subramaniam
Soby Mathew
Andrew Walbran
Anthony Steinhauser
Luka Kovacic
Deepika Bhavnani
Vishnu Banavath
Paul Beesley
György Szing
Ambroise Vincent